diff options
Diffstat (limited to 'drivers/net/ethernet/broadcom')
| -rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x.h | 7 | ||||
| -rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c | 94 | ||||
| -rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 6 | ||||
| -rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h | 1 | ||||
| -rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c | 15 | ||||
| -rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.h | 7 | ||||
| -rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c | 254 | ||||
| -rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h | 1 | ||||
| -rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c | 28 | ||||
| -rw-r--r-- | drivers/net/ethernet/broadcom/tg3.c | 2 |
10 files changed, 257 insertions, 158 deletions
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h index dad67905f4e2..eb105abcf0e7 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h @@ -1250,7 +1250,10 @@ struct bnx2x_slowpath { * Therefore, if they would have been defined in the same union, * data can get corrupted. */ - struct afex_vif_list_ramrod_data func_afex_rdata; + union { + struct afex_vif_list_ramrod_data viflist_data; + struct function_update_data func_update; + } func_afex_rdata; /* used by dmae command executer */ struct dmae_command dmae[MAX_DMAE_C]; @@ -2501,4 +2504,6 @@ void bnx2x_set_local_cmng(struct bnx2x *bp); #define MCPR_SCRATCH_BASE(bp) \ (CHIP_IS_E1x(bp) ? MCP_REG_MCPR_SCRATCH : MCP_A_REG_MCPR_SCRATCH) +#define E1H_MAX_MF_SB_COUNT (HC_SB_MAX_SB_E1X/(E1HVN_MAX * PORT_MAX)) + #endif /* bnx2x.h */ diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c index 20dcc02431ca..11fc79585491 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c @@ -3865,6 +3865,19 @@ static void bnx2x_warpcore_enable_AN_KR(struct bnx2x_phy *phy, bnx2x_warpcore_enable_AN_KR2(phy, params, vars); } else { + /* Enable Auto-Detect to support 1G over CL37 as well */ + bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, + MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, 0x10); + + /* Force cl48 sync_status LOW to avoid getting stuck in CL73 + * parallel-detect loop when CL73 and CL37 are enabled. + */ + CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, + MDIO_AER_BLOCK_AER_REG, 0); + bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, + MDIO_WC_REG_RXB_ANA_RX_CONTROL_PCI, 0x0800); + bnx2x_set_aer_mmd(params, phy); + bnx2x_disable_kr2(params, vars, phy); } @@ -8120,17 +8133,20 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, *edc_mode = EDC_MODE_ACTIVE_DAC; else check_limiting_mode = 1; - } else if (copper_module_type & - SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE) { + } else { + *edc_mode = EDC_MODE_PASSIVE_DAC; + /* Even in case PASSIVE_DAC indication is not set, + * treat it as a passive DAC cable, since some cables + * don't have this indication. + */ + if (copper_module_type & + SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE) { DP(NETIF_MSG_LINK, "Passive Copper cable detected\n"); - *edc_mode = - EDC_MODE_PASSIVE_DAC; - } else { - DP(NETIF_MSG_LINK, - "Unknown copper-cable-type 0x%x !!!\n", - copper_module_type); - return -EINVAL; + } else { + DP(NETIF_MSG_LINK, + "Unknown copper-cable-type\n"); + } } break; } @@ -10825,9 +10841,9 @@ static int bnx2x_54618se_config_init(struct bnx2x_phy *phy, (1<<11)); if (((phy->req_line_speed == SPEED_AUTO_NEG) && - (phy->speed_cap_mask & - PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) || - (phy->req_line_speed == SPEED_1000)) { + (phy->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) || + (phy->req_line_speed == SPEED_1000)) { an_1000_val |= (1<<8); autoneg_val |= (1<<9 | 1<<12); if (phy->req_duplex == DUPLEX_FULL) @@ -10843,30 +10859,32 @@ static int bnx2x_54618se_config_init(struct bnx2x_phy *phy, 0x09, &an_1000_val); - /* Set 100 speed advertisement */ - if (((phy->req_line_speed == SPEED_AUTO_NEG) && - (phy->speed_cap_mask & - (PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL | - PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF)))) { - an_10_100_val |= (1<<7); - /* Enable autoneg and restart autoneg for legacy speeds */ - autoneg_val |= (1<<9 | 1<<12); - - if (phy->req_duplex == DUPLEX_FULL) - an_10_100_val |= (1<<8); - DP(NETIF_MSG_LINK, "Advertising 100M\n"); - } - - /* Set 10 speed advertisement */ - if (((phy->req_line_speed == SPEED_AUTO_NEG) && - (phy->speed_cap_mask & - (PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL | - PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF)))) { - an_10_100_val |= (1<<5); - autoneg_val |= (1<<9 | 1<<12); - if (phy->req_duplex == DUPLEX_FULL) + /* Advertise 10/100 link speed */ + if (phy->req_line_speed == SPEED_AUTO_NEG) { + if (phy->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF) { + an_10_100_val |= (1<<5); + autoneg_val |= (1<<9 | 1<<12); + DP(NETIF_MSG_LINK, "Advertising 10M-HD\n"); + } + if (phy->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL) { an_10_100_val |= (1<<6); - DP(NETIF_MSG_LINK, "Advertising 10M\n"); + autoneg_val |= (1<<9 | 1<<12); + DP(NETIF_MSG_LINK, "Advertising 10M-FD\n"); + } + if (phy->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF) { + an_10_100_val |= (1<<7); + autoneg_val |= (1<<9 | 1<<12); + DP(NETIF_MSG_LINK, "Advertising 100M-HD\n"); + } + if (phy->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL) { + an_10_100_val |= (1<<8); + autoneg_val |= (1<<9 | 1<<12); + DP(NETIF_MSG_LINK, "Advertising 100M-FD\n"); + } } /* Only 10/100 are allowed to work in FORCE mode */ @@ -13342,6 +13360,10 @@ static u8 bnx2x_analyze_link_error(struct link_params *params, DP(NETIF_MSG_LINK, "Link changed:[%x %x]->%x\n", vars->link_up, old_status, status); + /* Do not touch the link in case physical link down */ + if ((vars->phy_flags & PHY_PHYSICAL_LINK_FLAG) == 0) + return 1; + /* a. Update shmem->link_status accordingly * b. Update link_vars->link_up */ @@ -13550,7 +13572,7 @@ static void bnx2x_check_kr2_wa(struct link_params *params, */ not_kr2_device = (((base_page & 0x8000) == 0) || (((base_page & 0x8000) && - ((next_page & 0xe0) == 0x2)))); + ((next_page & 0xe0) == 0x20)))); /* In case KR2 is already disabled, check if we need to re-enable it */ if (!(vars->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c index d3748bf3ac7b..18498fed520b 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c @@ -11517,9 +11517,9 @@ static int bnx2x_get_hwinfo(struct bnx2x *bp) } } - /* adjust igu_sb_cnt to MF for E1x */ - if (CHIP_IS_E1x(bp) && IS_MF(bp)) - bp->igu_sb_cnt /= E1HVN_MAX; + /* adjust igu_sb_cnt to MF for E1H */ + if (CHIP_IS_E1H(bp) && IS_MF(bp)) + bp->igu_sb_cnt = min_t(u8, bp->igu_sb_cnt, E1H_MAX_MF_SB_COUNT); /* port info */ bnx2x_get_port_hwinfo(bp); diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h index 08f8047188e9..2beb5430b876 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h @@ -7180,6 +7180,7 @@ Theotherbitsarereservedandshouldbezero*/ #define MDIO_WC_REG_RX1_PCI_CTRL 0x80ca #define MDIO_WC_REG_RX2_PCI_CTRL 0x80da #define MDIO_WC_REG_RX3_PCI_CTRL 0x80ea +#define MDIO_WC_REG_RXB_ANA_RX_CONTROL_PCI 0x80fa #define MDIO_WC_REG_XGXSBLK2_UNICORE_MODE_10G 0x8104 #define MDIO_WC_REG_XGXS_STATUS3 0x8129 #define MDIO_WC_REG_PAR_DET_10G_STATUS 0x8130 diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c index babf7b954ae6..98cccd487fc2 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c @@ -2036,6 +2036,7 @@ static int bnx2x_vlan_mac_del_all(struct bnx2x *bp, struct bnx2x_vlan_mac_ramrod_params p; struct bnx2x_exe_queue_obj *exeq = &o->exe_queue; struct bnx2x_exeq_elem *exeq_pos, *exeq_pos_n; + unsigned long flags; int read_lock; int rc = 0; @@ -2044,8 +2045,9 @@ static int bnx2x_vlan_mac_del_all(struct bnx2x *bp, spin_lock_bh(&exeq->lock); list_for_each_entry_safe(exeq_pos, exeq_pos_n, &exeq->exe_queue, link) { - if (exeq_pos->cmd_data.vlan_mac.vlan_mac_flags == - *vlan_mac_flags) { + flags = exeq_pos->cmd_data.vlan_mac.vlan_mac_flags; + if (BNX2X_VLAN_MAC_CMP_FLAGS(flags) == + BNX2X_VLAN_MAC_CMP_FLAGS(*vlan_mac_flags)) { rc = exeq->remove(bp, exeq->owner, exeq_pos); if (rc) { BNX2X_ERR("Failed to remove command\n"); @@ -2078,7 +2080,9 @@ static int bnx2x_vlan_mac_del_all(struct bnx2x *bp, return read_lock; list_for_each_entry(pos, &o->head, link) { - if (pos->vlan_mac_flags == *vlan_mac_flags) { + flags = pos->vlan_mac_flags; + if (BNX2X_VLAN_MAC_CMP_FLAGS(flags) == + BNX2X_VLAN_MAC_CMP_FLAGS(*vlan_mac_flags)) { p.user_req.vlan_mac_flags = pos->vlan_mac_flags; memcpy(&p.user_req.u, &pos->u, sizeof(pos->u)); rc = bnx2x_config_vlan_mac(bp, &p); @@ -4380,8 +4384,11 @@ int bnx2x_config_rss(struct bnx2x *bp, struct bnx2x_raw_obj *r = &o->raw; /* Do nothing if only driver cleanup was requested */ - if (test_bit(RAMROD_DRV_CLR_ONLY, &p->ramrod_flags)) + if (test_bit(RAMROD_DRV_CLR_ONLY, &p->ramrod_flags)) { + DP(BNX2X_MSG_SP, "Not configuring RSS ramrod_flags=%lx\n", + p->ramrod_flags); return 0; + } r->set_pending(r); diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.h index 658f4e33abf9..6a53c15c85a3 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.h @@ -266,6 +266,13 @@ enum { BNX2X_DONT_CONSUME_CAM_CREDIT, BNX2X_DONT_CONSUME_CAM_CREDIT_DEST, }; +/* When looking for matching filters, some flags are not interesting */ +#define BNX2X_VLAN_MAC_CMP_MASK (1 << BNX2X_UC_LIST_MAC | \ + 1 << BNX2X_ETH_MAC | \ + 1 << BNX2X_ISCSI_ETH_MAC | \ + 1 << BNX2X_NETQ_ETH_MAC) +#define BNX2X_VLAN_MAC_CMP_FLAGS(flags) \ + ((flags) & BNX2X_VLAN_MAC_CMP_MASK) struct bnx2x_vlan_mac_ramrod_params { /* Object to run the command from */ diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c index 6fe52d301dfe..31ab924600c1 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c @@ -1213,6 +1213,11 @@ static void bnx2x_vfop_rxmode(struct bnx2x *bp, struct bnx2x_virtf *vf) /* next state */ vfop->state = BNX2X_VFOP_RXMODE_DONE; + /* record the accept flags in vfdb so hypervisor can modify them + * if necessary + */ + bnx2x_vfq(vf, ramrod->cl_id - vf->igu_base_id, accept_flags) = + ramrod->rx_accept_flags; vfop->rc = bnx2x_config_rx_mode(bp, ramrod); bnx2x_vfop_finalize(vf, vfop->rc, VFOP_DONE); op_err: @@ -1228,39 +1233,43 @@ op_pending: return; } +static void bnx2x_vf_prep_rx_mode(struct bnx2x *bp, u8 qid, + struct bnx2x_rx_mode_ramrod_params *ramrod, + struct bnx2x_virtf *vf, + unsigned long accept_flags) +{ + struct bnx2x_vf_queue *vfq = vfq_get(vf, qid); + + memset(ramrod, 0, sizeof(*ramrod)); + ramrod->cid = vfq->cid; + ramrod->cl_id = vfq_cl_id(vf, vfq); + ramrod->rx_mode_obj = &bp->rx_mode_obj; + ramrod->func_id = FW_VF_HANDLE(vf->abs_vfid); + ramrod->rx_accept_flags = accept_flags; + ramrod->tx_accept_flags = accept_flags; + ramrod->pstate = &vf->filter_state; + ramrod->state = BNX2X_FILTER_RX_MODE_PENDING; + + set_bit(BNX2X_FILTER_RX_MODE_PENDING, &vf->filter_state); + set_bit(RAMROD_RX, &ramrod->ramrod_flags); + set_bit(RAMROD_TX, &ramrod->ramrod_flags); + + ramrod->rdata = bnx2x_vf_sp(bp, vf, rx_mode_rdata.e2); + ramrod->rdata_mapping = bnx2x_vf_sp_map(bp, vf, rx_mode_rdata.e2); +} + int bnx2x_vfop_rxmode_cmd(struct bnx2x *bp, struct bnx2x_virtf *vf, struct bnx2x_vfop_cmd *cmd, int qid, unsigned long accept_flags) { - struct bnx2x_vf_queue *vfq = vfq_get(vf, qid); struct bnx2x_vfop *vfop = bnx2x_vfop_add(bp, vf); if (vfop) { struct bnx2x_rx_mode_ramrod_params *ramrod = &vf->op_params.rx_mode; - memset(ramrod, 0, sizeof(*ramrod)); - - /* Prepare ramrod parameters */ - ramrod->cid = vfq->cid; - ramrod->cl_id = vfq_cl_id(vf, vfq); - ramrod->rx_mode_obj = &bp->rx_mode_obj; - ramrod->func_id = FW_VF_HANDLE(vf->abs_vfid); - - ramrod->rx_accept_flags = accept_flags; - ramrod->tx_accept_flags = accept_flags; - ramrod->pstate = &vf->filter_state; - ramrod->state = BNX2X_FILTER_RX_MODE_PENDING; - - set_bit(BNX2X_FILTER_RX_MODE_PENDING, &vf->filter_state); - set_bit(RAMROD_RX, &ramrod->ramrod_flags); - set_bit(RAMROD_TX, &ramrod->ramrod_flags); - - ramrod->rdata = - bnx2x_vf_sp(bp, vf, rx_mode_rdata.e2); - ramrod->rdata_mapping = - bnx2x_vf_sp_map(bp, vf, rx_mode_rdata.e2); + bnx2x_vf_prep_rx_mode(bp, qid, ramrod, vf, accept_flags); bnx2x_vfop_opset(BNX2X_VFOP_RXMODE_CONFIG, bnx2x_vfop_rxmode, cmd->done); @@ -3213,13 +3222,16 @@ int bnx2x_enable_sriov(struct bnx2x *bp) bnx2x_iov_static_resc(bp, vf); } - /* prepare msix vectors in VF configuration space */ + /* prepare msix vectors in VF configuration space - the value in the + * PCI configuration space should be the index of the last entry, + * namely one less than the actual size of the table + */ for (vf_idx = first_vf; vf_idx < first_vf + req_vfs; vf_idx++) { bnx2x_pretend_func(bp, HW_VF_HANDLE(bp, vf_idx)); REG_WR(bp, PCICFG_OFFSET + GRC_CONFIG_REG_VF_MSIX_CONTROL, - num_vf_queues); + num_vf_queues - 1); DP(BNX2X_MSG_IOV, "set msix vec num in VF %d cfg space to %d\n", - vf_idx, num_vf_queues); + vf_idx, num_vf_queues - 1); } bnx2x_pretend_func(bp, BP_ABS_FUNC(bp)); @@ -3447,10 +3459,18 @@ out: int bnx2x_set_vf_vlan(struct net_device *dev, int vfidx, u16 vlan, u8 qos) { + struct bnx2x_queue_state_params q_params = {NULL}; + struct bnx2x_vlan_mac_ramrod_params ramrod_param; + struct bnx2x_queue_update_params *update_params; + struct pf_vf_bulletin_content *bulletin = NULL; + struct bnx2x_rx_mode_ramrod_params rx_ramrod; struct bnx2x *bp = netdev_priv(dev); - int rc, q_logical_state; + struct bnx2x_vlan_mac_obj *vlan_obj; + unsigned long vlan_mac_flags = 0; + unsigned long ramrod_flags = 0; struct bnx2x_virtf *vf = NULL; - struct pf_vf_bulletin_content *bulletin = NULL; + unsigned long accept_flags; + int rc; /* sanity and init */ rc = bnx2x_vf_ndo_prep(bp, vfidx, &vf, &bulletin); @@ -3468,104 +3488,118 @@ int bnx2x_set_vf_vlan(struct net_device *dev, int vfidx, u16 vlan, u8 qos) /* update PF's copy of the VF's bulletin. No point in posting the vlan * to the VF since it doesn't have anything to do with it. But it useful * to store it here in case the VF is not up yet and we can only - * configure the vlan later when it does. + * configure the vlan later when it does. Treat vlan id 0 as remove the + * Host tag. */ - bulletin->valid_bitmap |= 1 << VLAN_VALID; + if (vlan > 0) + bulletin->valid_bitmap |= 1 << VLAN_VALID; + else + bulletin->valid_bitmap &= ~(1 << VLAN_VALID); bulletin->vlan = vlan; /* is vf initialized and queue set up? */ - q_logical_state = - bnx2x_get_q_logical_state(bp, &bnx2x_leading_vfq(vf, sp_obj)); - if (vf->state == VF_ENABLED && - q_logical_state == BNX2X_Q_LOGICAL_STATE_ACTIVE) { - /* configure the vlan in device on this vf's queue */ - unsigned long ramrod_flags = 0; - unsigned long vlan_mac_flags = 0; - struct bnx2x_vlan_mac_obj *vlan_obj = - &bnx2x_leading_vfq(vf, vlan_obj); - struct bnx2x_vlan_mac_ramrod_params ramrod_param; - struct bnx2x_queue_state_params q_params = {NULL}; - struct bnx2x_queue_update_params *update_params; + if (vf->state != VF_ENABLED || + bnx2x_get_q_logical_state(bp, &bnx2x_leading_vfq(vf, sp_obj)) != + BNX2X_Q_LOGICAL_STATE_ACTIVE) + return rc; - rc = validate_vlan_mac(bp, &bnx2x_leading_vfq(vf, mac_obj)); - if (rc) - return rc; - memset(&ramrod_param, 0, sizeof(ramrod_param)); + /* configure the vlan in device on this vf's queue */ + vlan_obj = &bnx2x_leading_vfq(vf, vlan_obj); + rc = validate_vlan_mac(bp, &bnx2x_leading_vfq(vf, mac_obj)); + if (rc) + return rc; - /* must lock vfpf channel to protect against vf flows */ - bnx2x_lock_vf_pf_channel(bp, vf, CHANNEL_TLV_PF_SET_VLAN); + /* must lock vfpf channel to protect against vf flows */ + bnx2x_lock_vf_pf_channel(bp, vf, CHANNEL_TLV_PF_SET_VLAN); - /* remove existing vlans */ - __set_bit(RAMROD_COMP_WAIT, &ramrod_flags); - rc = vlan_obj->delete_all(bp, vlan_obj, &vlan_mac_flags, - &ramrod_flags); - if (rc) { - BNX2X_ERR("failed to delete vlans\n"); - rc = -EINVAL; - goto out; - } + /* remove existing vlans */ + __set_bit(RAMROD_COMP_WAIT, &ramrod_flags); + rc = vlan_obj->delete_all(bp, vlan_obj, &vlan_mac_flags, + &ramrod_flags); + if (rc) { + BNX2X_ERR("failed to delete vlans\n"); + rc = -EINVAL; + goto out; + } + + /* need to remove/add the VF's accept_any_vlan bit */ + accept_flags = bnx2x_leading_vfq(vf, accept_flags); + if (vlan) + clear_bit(BNX2X_ACCEPT_ANY_VLAN, &accept_flags); + else + set_bit(BNX2X_ACCEPT_ANY_VLAN, &accept_flags); + + bnx2x_vf_prep_rx_mode(bp, LEADING_IDX, &rx_ramrod, vf, + accept_flags); + bnx2x_leading_vfq(vf, accept_flags) = accept_flags; + bnx2x_config_rx_mode(bp, &rx_ramrod); + + /* configure the new vlan to device */ + memset(&ramrod_param, 0, sizeof(ramrod_param)); + __set_bit(RAMROD_COMP_WAIT, &ramrod_flags); + ramrod_param.vlan_mac_obj = vlan_obj; + ramrod_param.ramrod_flags = ramrod_flags; + set_bit(BNX2X_DONT_CONSUME_CAM_CREDIT, + &ramrod_param.user_req.vlan_mac_flags); + ramrod_param.user_req.u.vlan.vlan = vlan; + ramrod_param.user_req.cmd = BNX2X_VLAN_MAC_ADD; + rc = bnx2x_config_vlan_mac(bp, &ramrod_param); + if (rc) { + BNX2X_ERR("failed to configure vlan\n"); + rc = -EINVAL; + goto out; + } - /* send queue update ramrod to configure default vlan and silent - * vlan removal + /* send queue update ramrod to configure default vlan and silent + * vlan removal + */ + __set_bit(RAMROD_COMP_WAIT, &q_params.ramrod_flags); + q_params.cmd = BNX2X_Q_CMD_UPDATE; + q_params.q_obj = &bnx2x_leading_vfq(vf, sp_obj); + update_params = &q_params.params.update; + __set_bit(BNX2X_Q_UPDATE_DEF_VLAN_EN_CHNG, + &update_params->update_flags); + __set_bit(BNX2X_Q_UPDATE_SILENT_VLAN_REM_CHNG, + &update_params->update_flags); + if (vlan == 0) { + /* if vlan is 0 then we want to leave the VF traffic + * untagged, and leave the incoming traffic untouched + * (i.e. do not remove any vlan tags). */ - __set_bit(RAMROD_COMP_WAIT, &q_params.ramrod_flags); - q_params.cmd = BNX2X_Q_CMD_UPDATE; - q_params.q_obj = &bnx2x_leading_vfq(vf, sp_obj); - update_params = &q_params.params.update; - __set_bit(BNX2X_Q_UPDATE_DEF_VLAN_EN_CHNG, + __clear_bit(BNX2X_Q_UPDATE_DEF_VLAN_EN, + &update_params->update_flags); + __clear_bit(BNX2X_Q_UPDATE_SILENT_VLAN_REM, + &update_params->update_flags); + } else { + /* configure default vlan to vf queue and set silent + * vlan removal (the vf remains unaware of this vlan). + */ + __set_bit(BNX2X_Q_UPDATE_DEF_VLAN_EN, &update_params->update_flags); - __set_bit(BNX2X_Q_UPDATE_SILENT_VLAN_REM_CHNG, + __set_bit(BNX2X_Q_UPDATE_SILENT_VLAN_REM, &update_params->update_flags); + update_params->def_vlan = vlan; + update_params->silent_removal_value = + vlan & VLAN_VID_MASK; + update_params->silent_removal_mask = VLAN_VID_MASK; + } - if (vlan == 0) { - /* if vlan is 0 then we want to leave the VF traffic - * untagged, and leave the incoming traffic untouched - * (i.e. do not remove any vlan tags). - */ - __clear_bit(BNX2X_Q_UPDATE_DEF_VLAN_EN, - &update_params->update_flags); - __clear_bit(BNX2X_Q_UPDATE_SILENT_VLAN_REM, - &update_params->update_flags); - } else { - /* configure the new vlan to device */ - __set_bit(RAMROD_COMP_WAIT, &ramrod_flags); - ramrod_param.vlan_mac_obj = vlan_obj; - ramrod_param.ramrod_flags = ramrod_flags; - ramrod_param.user_req.u.vlan.vlan = vlan; - ramrod_param.user_req.cmd = BNX2X_VLAN_MAC_ADD; - rc = bnx2x_config_vlan_mac(bp, &ramrod_param); - if (rc) { - BNX2X_ERR("failed to configure vlan\n"); - rc = -EINVAL; - goto out; - } - - /* configure default vlan to vf queue and set silent - * vlan removal (the vf remains unaware of this vlan). - */ - update_params = &q_params.params.update; - __set_bit(BNX2X_Q_UPDATE_DEF_VLAN_EN, - &update_params->update_flags); - __set_bit(BNX2X_Q_UPDATE_SILENT_VLAN_REM, - &update_params->update_flags); - update_params->def_vlan = vlan; - } + /* Update the Queue state */ + rc = bnx2x_queue_state_change(bp, &q_params); + if (rc) { + BNX2X_ERR("Failed to configure default VLAN\n"); + goto out; + } - /* Update the Queue state */ - rc = bnx2x_queue_state_change(bp, &q_params); - if (rc) { - BNX2X_ERR("Failed to configure default VLAN\n"); - goto out; - } - /* clear the flag indicating that this VF needs its vlan - * (will only be set if the HV configured the Vlan before vf was - * up and we were called because the VF came up later - */ + /* clear the flag indicating that this VF needs its vlan + * (will only be set if the HV configured the Vlan before vf was + * up and we were called because the VF came up later + */ out: - vf->cfg_flags &= ~VF_CFG_VLAN; - bnx2x_unlock_vf_pf_channel(bp, vf, CHANNEL_TLV_PF_SET_VLAN); - } + vf->cfg_flags &= ~VF_CFG_VLAN; + bnx2x_unlock_vf_pf_channel(bp, vf, CHANNEL_TLV_PF_SET_VLAN); + return rc; } diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h index a5c84a7d454c..d72ab7e24de0 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h @@ -74,6 +74,7 @@ struct bnx2x_vf_queue { /* VLANs object */ struct bnx2x_vlan_mac_obj vlan_obj; atomic_t vlan_count; /* 0 means vlan-0 is set ~ untagged */ + unsigned long accept_flags; /* last accept flags configured */ /* Queue Slow-path State object */ struct bnx2x_queue_sp_obj sp_obj; diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c index e5f7985a372c..1b1ad31b4553 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c @@ -208,7 +208,7 @@ static int bnx2x_get_vf_id(struct bnx2x *bp, u32 *vf_id) return -EINVAL; } - BNX2X_ERR("valid ME register value: 0x%08x\n", me_reg); + DP(BNX2X_MSG_IOV, "valid ME register value: 0x%08x\n", me_reg); *vf_id = (me_reg & ME_REG_VF_NUM_MASK) >> ME_REG_VF_NUM_SHIFT; @@ -1610,6 +1610,8 @@ static void bnx2x_vfop_mbx_qfilters(struct bnx2x *bp, struct bnx2x_virtf *vf) if (msg->flags & VFPF_SET_Q_FILTERS_RX_MASK_CHANGED) { unsigned long accept = 0; + struct pf_vf_bulletin_content *bulletin = + BP_VF_BULLETIN(bp, vf->index); /* covert VF-PF if mask to bnx2x accept flags */ if (msg->rx_mask & VFPF_RX_MASK_ACCEPT_MATCHED_UNICAST) @@ -1629,9 +1631,11 @@ static void bnx2x_vfop_mbx_qfilters(struct bnx2x *bp, struct bnx2x_virtf *vf) __set_bit(BNX2X_ACCEPT_BROADCAST, &accept); /* A packet arriving the vf's mac should be accepted - * with any vlan + * with any vlan, unless a vlan has already been + * configured. */ - __set_bit(BNX2X_ACCEPT_ANY_VLAN, &accept); + if (!(bulletin->valid_bitmap & (1 << VLAN_VALID))) + __set_bit(BNX2X_ACCEPT_ANY_VLAN, &accept); /* set rx-mode */ rc = bnx2x_vfop_rxmode_cmd(bp, vf, &cmd, @@ -1722,6 +1726,21 @@ static void bnx2x_vf_mbx_set_q_filters(struct bnx2x *bp, goto response; } } + /* if vlan was set by hypervisor we don't allow guest to config vlan */ + if (bulletin->valid_bitmap & 1 << VLAN_VALID) { + int i; + + /* search for vlan filters */ + for (i = 0; i < filters->n_mac_vlan_filters; i++) { + if (filters->filters[i].flags & + VFPF_Q_FILTER_VLAN_TAG_VALID) { + BNX2X_ERR("VF[%d] attempted to configure vlan but one was already set by Hypervisor. Aborting request\n", + vf->abs_vfid); + vf->op_rc = -EPERM; + goto response; + } + } + } /* verify vf_qid */ if (filters->vf_qid > vf_rxq_count(vf)) @@ -1817,6 +1836,9 @@ static void bnx2x_vf_mbx_update_rss(struct bnx2x *bp, struct bnx2x_virtf *vf, vf_op_params->rss_result_mask = rss_tlv->rss_result_mask; /* flags handled individually for backward/forward compatability */ + vf_op_params->rss_flags = 0; + vf_op_params->ramrod_flags = 0; + if (rss_tlv->rss_flags & VFPF_RSS_MODE_DISABLED) __set_bit(BNX2X_RSS_MODE_DISABLED, &vf_op_params->rss_flags); if (rss_tlv->rss_flags & VFPF_RSS_MODE_REGULAR) diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c index d88ef551dfcd..c37e9f27ff6d 100644 --- a/drivers/net/ethernet/broadcom/tg3.c +++ b/drivers/net/ethernet/broadcom/tg3.c @@ -7638,7 +7638,7 @@ static inline int tg3_4g_overflow_test(dma_addr_t mapping, int len) { u32 base = (u32) mapping & 0xffffffff; - return (base > 0xffffdcc0) && (base + len + 8 < base); + return base + len + 8 < base; } /* Test for TSO DMA buffers that cross into regions which are within MSS bytes |