summaryrefslogtreecommitdiff
path: root/drivers/pinctrl/pinctrl-coh901.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/pinctrl/pinctrl-coh901.c')
-rw-r--r--drivers/pinctrl/pinctrl-coh901.c220
1 files changed, 43 insertions, 177 deletions
diff --git a/drivers/pinctrl/pinctrl-coh901.c b/drivers/pinctrl/pinctrl-coh901.c
index cc0f00d73d15..b446c9641212 100644
--- a/drivers/pinctrl/pinctrl-coh901.c
+++ b/drivers/pinctrl/pinctrl-coh901.c
@@ -1,11 +1,8 @@
/*
* U300 GPIO module.
*
- * Copyright (C) 2007-2011 ST-Ericsson AB
+ * Copyright (C) 2007-2012 ST-Ericsson AB
* License terms: GNU General Public License (GPL) version 2
- * This can driver either of the two basic GPIO cores
- * available in the U300 platforms:
- * COH 901 335 - Used in DB3150 (U300 1.0) and DB3200 (U330 1.0)
* COH 901 571/3 - Used in DB3210 (U365 2.0) and DB3350 (U335 1.0)
* Author: Linus Walleij <linus.walleij@linaro.org>
* Author: Jonas Aaberg <jonas.aberg@stericsson.com>
@@ -24,19 +21,22 @@
#include <linux/slab.h>
#include <linux/pinctrl/consumer.h>
#include <linux/pinctrl/pinconf-generic.h>
-#include <mach/gpio-u300.h>
+#include <linux/platform_data/pinctrl-coh901.h>
#include "pinctrl-coh901.h"
+#define U300_GPIO_PORT_STRIDE (0x30)
/*
- * Register definitions for COH 901 335 variant
+ * Control Register 32bit (R/W)
+ * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
+ * gives the number of GPIO pins.
+ * bit 8-2 (mask 0x000001FC) contains the core version ID.
*/
-#define U300_335_PORT_STRIDE (0x1C)
-/* Port X Pin Data Register 32bit, this is both input and output (R/W) */
-#define U300_335_PXPDIR (0x00)
-#define U300_335_PXPDOR (0x00)
-/* Port X Pin Config Register 32bit (R/W) */
-#define U300_335_PXPCR (0x04)
-/* This register layout is the same in both blocks */
+#define U300_GPIO_CR (0x00)
+#define U300_GPIO_CR_SYNC_SEL_ENABLE (0x00000002UL)
+#define U300_GPIO_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL)
+#define U300_GPIO_PXPDIR (0x04)
+#define U300_GPIO_PXPDOR (0x08)
+#define U300_GPIO_PXPCR (0x0C)
#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL)
#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL)
#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL)
@@ -44,53 +44,17 @@
#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL)
#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL)
#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL)
-/* Port X Interrupt Event Register 32bit (R/W) */
-#define U300_335_PXIEV (0x08)
-/* Port X Interrupt Enable Register 32bit (R/W) */
-#define U300_335_PXIEN (0x0C)
-/* Port X Interrupt Force Register 32bit (R/W) */
-#define U300_335_PXIFR (0x10)
-/* Port X Interrupt Config Register 32bit (R/W) */
-#define U300_335_PXICR (0x14)
-/* This register layout is the same in both blocks */
+#define U300_GPIO_PXPER (0x10)
+#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL)
+#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL)
+#define U300_GPIO_PXIEV (0x14)
+#define U300_GPIO_PXIEN (0x18)
+#define U300_GPIO_PXIFR (0x1C)
+#define U300_GPIO_PXICR (0x20)
#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL)
#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL)
#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL)
#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL)
-/* Port X Pull-up Enable Register 32bit (R/W) */
-#define U300_335_PXPER (0x18)
-/* This register layout is the same in both blocks */
-#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL)
-/* Control Register 32bit (R/W) */
-#define U300_335_CR (0x54)
-#define U300_335_CR_BLOCK_CLOCK_ENABLE (0x00000001UL)
-
-/*
- * Register definitions for COH 901 571 / 3 variant
- */
-#define U300_571_PORT_STRIDE (0x30)
-/*
- * Control Register 32bit (R/W)
- * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
- * gives the number of GPIO pins.
- * bit 8-2 (mask 0x000001FC) contains the core version ID.
- */
-#define U300_571_CR (0x00)
-#define U300_571_CR_SYNC_SEL_ENABLE (0x00000002UL)
-#define U300_571_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL)
-/*
- * These registers have the same layout and function as the corresponding
- * COH 901 335 registers, just at different offset.
- */
-#define U300_571_PXPDIR (0x04)
-#define U300_571_PXPDOR (0x08)
-#define U300_571_PXPCR (0x0C)
-#define U300_571_PXPER (0x10)
-#define U300_571_PXIEV (0x14)
-#define U300_571_PXIEN (0x18)
-#define U300_571_PXIFR (0x1C)
-#define U300_571_PXICR (0x20)
/* 8 bits per port, no version has more than 7 ports */
#define U300_GPIO_PINS_PER_PORT 8
@@ -149,8 +113,6 @@ struct u300_gpio_confdata {
/* BS335 has seven ports of 8 bits each = GPIO pins 0..55 */
#define BS335_GPIO_NUM_PORTS 7
-/* BS365 has five ports of 8 bits each = GPIO pins 0..39 */
-#define BS365_GPIO_NUM_PORTS 5
#define U300_FLOATING_INPUT { \
.bias_mode = PIN_CONFIG_BIAS_HIGH_IMPEDANCE, \
@@ -172,7 +134,6 @@ struct u300_gpio_confdata {
.outval = 1, \
}
-
/* Initial configuration */
static const struct __initconst u300_gpio_confdata
bs335_gpio_config[BS335_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
@@ -255,66 +216,6 @@ bs335_gpio_config[BS335_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
}
};
-static const struct __initconst u300_gpio_confdata
-bs365_gpio_config[BS365_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
- /* Port 0, pins 0-7 */
- {
- U300_FLOATING_INPUT,
- U300_OUTPUT_LOW,
- U300_FLOATING_INPUT,
- U300_OUTPUT_LOW,
- U300_OUTPUT_LOW,
- U300_OUTPUT_LOW,
- U300_PULL_UP_INPUT,
- U300_FLOATING_INPUT,
- },
- /* Port 1, pins 0-7 */
- {
- U300_OUTPUT_LOW,
- U300_FLOATING_INPUT,
- U300_OUTPUT_LOW,
- U300_FLOATING_INPUT,
- U300_FLOATING_INPUT,
- U300_OUTPUT_HIGH,
- U300_OUTPUT_LOW,
- U300_OUTPUT_LOW,
- },
- /* Port 2, pins 0-7 */
- {
- U300_FLOATING_INPUT,
- U300_PULL_UP_INPUT,
- U300_OUTPUT_LOW,
- U300_OUTPUT_LOW,
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- },
- /* Port 3, pins 0-7 */
- {
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- },
- /* Port 4, pins 0-7 */
- {
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- U300_PULL_UP_INPUT,
- /* These 4 pins doesn't exist on DB3210 */
- U300_OUTPUT_LOW,
- U300_OUTPUT_LOW,
- U300_OUTPUT_LOW,
- U300_OUTPUT_LOW,
- }
-};
-
/**
* to_u300_gpio() - get the pointer to u300_gpio
* @chip: the gpio chip member of the structure u300_gpio
@@ -716,13 +617,7 @@ static void __init u300_gpio_init_coh901571(struct u300_gpio *gpio,
const struct u300_gpio_confdata *conf;
int offset = (i*8) + j;
- if (plat->variant == U300_GPIO_COH901571_3_BS335)
- conf = &bs335_gpio_config[i][j];
- else if (plat->variant == U300_GPIO_COH901571_3_BS365)
- conf = &bs365_gpio_config[i][j];
- else
- break;
-
+ conf = &bs335_gpio_config[i][j];
u300_gpio_init_pin(gpio, offset, conf);
}
}
@@ -796,50 +691,27 @@ static int __init u300_gpio_probe(struct platform_device *pdev)
goto err_no_ioremap;
}
- if (plat->variant == U300_GPIO_COH901335) {
- dev_info(gpio->dev,
- "initializing GPIO Controller COH 901 335\n");
- gpio->stride = U300_335_PORT_STRIDE;
- gpio->pcr = U300_335_PXPCR;
- gpio->dor = U300_335_PXPDOR;
- gpio->dir = U300_335_PXPDIR;
- gpio->per = U300_335_PXPER;
- gpio->icr = U300_335_PXICR;
- gpio->ien = U300_335_PXIEN;
- gpio->iev = U300_335_PXIEV;
- ifr = U300_335_PXIFR;
-
- /* Turn on the GPIO block */
- writel(U300_335_CR_BLOCK_CLOCK_ENABLE,
- gpio->base + U300_335_CR);
- } else if (plat->variant == U300_GPIO_COH901571_3_BS335 ||
- plat->variant == U300_GPIO_COH901571_3_BS365) {
- dev_info(gpio->dev,
- "initializing GPIO Controller COH 901 571/3\n");
- gpio->stride = U300_571_PORT_STRIDE;
- gpio->pcr = U300_571_PXPCR;
- gpio->dor = U300_571_PXPDOR;
- gpio->dir = U300_571_PXPDIR;
- gpio->per = U300_571_PXPER;
- gpio->icr = U300_571_PXICR;
- gpio->ien = U300_571_PXIEN;
- gpio->iev = U300_571_PXIEV;
- ifr = U300_571_PXIFR;
-
- val = readl(gpio->base + U300_571_CR);
- dev_info(gpio->dev, "COH901571/3 block version: %d, " \
- "number of cores: %d totalling %d pins\n",
- ((val & 0x000001FC) >> 2),
- ((val & 0x0000FE00) >> 9),
- ((val & 0x0000FE00) >> 9) * 8);
- writel(U300_571_CR_BLOCK_CLKRQ_ENABLE,
- gpio->base + U300_571_CR);
- u300_gpio_init_coh901571(gpio, plat);
- } else {
- dev_err(gpio->dev, "unknown block variant\n");
- err = -ENODEV;
- goto err_unknown_variant;
- }
+ dev_info(gpio->dev,
+ "initializing GPIO Controller COH 901 571/3\n");
+ gpio->stride = U300_GPIO_PORT_STRIDE;
+ gpio->pcr = U300_GPIO_PXPCR;
+ gpio->dor = U300_GPIO_PXPDOR;
+ gpio->dir = U300_GPIO_PXPDIR;
+ gpio->per = U300_GPIO_PXPER;
+ gpio->icr = U300_GPIO_PXICR;
+ gpio->ien = U300_GPIO_PXIEN;
+ gpio->iev = U300_GPIO_PXIEV;
+ ifr = U300_GPIO_PXIFR;
+
+ val = readl(gpio->base + U300_GPIO_CR);
+ dev_info(gpio->dev, "COH901571/3 block version: %d, " \
+ "number of cores: %d totalling %d pins\n",
+ ((val & 0x000001FC) >> 2),
+ ((val & 0x0000FE00) >> 9),
+ ((val & 0x0000FE00) >> 9) * 8);
+ writel(U300_GPIO_CR_BLOCK_CLKRQ_ENABLE,
+ gpio->base + U300_GPIO_CR);
+ u300_gpio_init_coh901571(gpio, plat);
/* Add each port with its IRQ separately */
INIT_LIST_HEAD(&gpio->port_list);
@@ -906,7 +778,6 @@ err_no_pinctrl:
err_no_chip:
err_no_port:
u300_gpio_free_ports(gpio);
-err_unknown_variant:
iounmap(gpio->base);
err_no_ioremap:
release_mem_region(gpio->memres->start, resource_size(gpio->memres));
@@ -923,16 +794,11 @@ err_no_clk:
static int __exit u300_gpio_remove(struct platform_device *pdev)
{
- struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev);
struct u300_gpio *gpio = platform_get_drvdata(pdev);
int err;
/* Turn off the GPIO block */
- if (plat->variant == U300_GPIO_COH901335)
- writel(0x00000000U, gpio->base + U300_335_CR);
- if (plat->variant == U300_GPIO_COH901571_3_BS335 ||
- plat->variant == U300_GPIO_COH901571_3_BS365)
- writel(0x00000000U, gpio->base + U300_571_CR);
+ writel(0x00000000U, gpio->base + U300_GPIO_CR);
err = gpiochip_remove(&gpio->chip);
if (err < 0) {