diff options
Diffstat (limited to 'drivers/power/supply')
41 files changed, 1820 insertions, 216 deletions
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig index 4a5e8e1d1237..663a1c423806 100644 --- a/drivers/power/supply/Kconfig +++ b/drivers/power/supply/Kconfig @@ -766,6 +766,14 @@ config BATTERY_RT5033 The fuelgauge calculates and determines the battery state of charge according to battery open circuit voltage. +config CHARGER_RT5033 + tristate "RT5033 battery charger support" + depends on MFD_RT5033 + help + This adds support for battery charger in Richtek RT5033 PMIC. + The device supports pre-charge mode, fast charge mode and + constant voltage mode. + config CHARGER_RT9455 tristate "Richtek RT9455 battery charger driver" depends on I2C @@ -934,4 +942,13 @@ config BATTERY_UG3105 device is off or suspended, the functionality of this driver is limited to reporting capacity only. +config CHARGER_QCOM_SMB2 + tristate "Qualcomm PMI8998 PMIC charger driver" + depends on MFD_SPMI_PMIC + depends on IIO + help + Say Y here to enable the Qualcomm PMIC Charger driver. This + adds support for the SMB2 switch mode battery charger found + in PMI8998 and related PMICs. + endif # POWER_SUPPLY diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile index 4adbfba02d05..a8a9fa6de1e9 100644 --- a/drivers/power/supply/Makefile +++ b/drivers/power/supply/Makefile @@ -54,6 +54,7 @@ obj-$(CONFIG_BATTERY_MAX17040) += max17040_battery.o obj-$(CONFIG_BATTERY_MAX17042) += max17042_battery.o obj-$(CONFIG_BATTERY_MAX1721X) += max1721x_battery.o obj-$(CONFIG_BATTERY_RT5033) += rt5033_battery.o +obj-$(CONFIG_CHARGER_RT5033) += rt5033_charger.o obj-$(CONFIG_CHARGER_RT9455) += rt9455_charger.o obj-$(CONFIG_CHARGER_RT9467) += rt9467-charger.o obj-$(CONFIG_CHARGER_RT9471) += rt9471.o @@ -109,3 +110,4 @@ obj-$(CONFIG_BATTERY_ACER_A500) += acer_a500_battery.o obj-$(CONFIG_BATTERY_SURFACE) += surface_battery.o obj-$(CONFIG_CHARGER_SURFACE) += surface_charger.o obj-$(CONFIG_BATTERY_UG3105) += ug3105_battery.o +obj-$(CONFIG_CHARGER_QCOM_SMB2) += qcom_pmi8998_charger.o diff --git a/drivers/power/supply/adp5061.c b/drivers/power/supply/adp5061.c index 840db629a46c..3e3a0d118ce5 100644 --- a/drivers/power/supply/adp5061.c +++ b/drivers/power/supply/adp5061.c @@ -736,7 +736,7 @@ static struct i2c_driver adp5061_driver = { .driver = { .name = KBUILD_MODNAME, }, - .probe_new = adp5061_probe, + .probe = adp5061_probe, .id_table = adp5061_id, }; module_i2c_driver(adp5061_driver); diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c index a1e6d1d44808..51c3f9b6458d 100644 --- a/drivers/power/supply/axp20x_usb_power.c +++ b/drivers/power/supply/axp20x_usb_power.c @@ -26,45 +26,48 @@ #define DRVNAME "axp20x-usb-power-supply" +#define AXP192_USB_OTG_STATUS 0x04 + #define AXP20X_PWR_STATUS_VBUS_PRESENT BIT(5) #define AXP20X_PWR_STATUS_VBUS_USED BIT(4) #define AXP20X_USB_STATUS_VBUS_VALID BIT(2) -#define AXP20X_VBUS_PATH_SEL BIT(7) -#define AXP20X_VBUS_PATH_SEL_OFFSET 7 - #define AXP20X_VBUS_VHOLD_uV(b) (4000000 + (((b) >> 3) & 7) * 100000) #define AXP20X_VBUS_VHOLD_MASK GENMASK(5, 3) #define AXP20X_VBUS_VHOLD_OFFSET 3 -#define AXP20X_VBUS_CLIMIT_MASK 3 -#define AXP20X_VBUS_CLIMIT_900mA 0 -#define AXP20X_VBUS_CLIMIT_500mA 1 -#define AXP20X_VBUS_CLIMIT_100mA 2 -#define AXP20X_VBUS_CLIMIT_NONE 3 - -#define AXP813_VBUS_CLIMIT_900mA 0 -#define AXP813_VBUS_CLIMIT_1500mA 1 -#define AXP813_VBUS_CLIMIT_2000mA 2 -#define AXP813_VBUS_CLIMIT_2500mA 3 #define AXP20X_ADC_EN1_VBUS_CURR BIT(2) #define AXP20X_ADC_EN1_VBUS_VOLT BIT(3) -#define AXP20X_VBUS_MON_VBUS_VALID BIT(3) - -#define AXP813_BC_EN BIT(0) - /* * Note do not raise the debounce time, we must report Vusb high within * 100ms otherwise we get Vbus errors in musb. */ #define DEBOUNCE_TIME msecs_to_jiffies(50) +struct axp_data { + const struct power_supply_desc *power_desc; + const char * const *irq_names; + unsigned int num_irq_names; + const int *curr_lim_table; + struct reg_field curr_lim_fld; + struct reg_field vbus_valid_bit; + struct reg_field vbus_mon_bit; + struct reg_field usb_bc_en_bit; + struct reg_field vbus_disable_bit; + bool vbus_needs_polling: 1; +}; + struct axp20x_usb_power { struct regmap *regmap; + struct regmap_field *curr_lim_fld; + struct regmap_field *vbus_valid_bit; + struct regmap_field *vbus_mon_bit; + struct regmap_field *usb_bc_en_bit; + struct regmap_field *vbus_disable_bit; struct power_supply *supply; - enum axp20x_variants axp20x_id; + const struct axp_data *axp_data; struct iio_channel *vbus_v; struct iio_channel *vbus_i; struct delayed_work vbus_detect; @@ -81,7 +84,7 @@ static bool axp20x_usb_vbus_needs_polling(struct axp20x_usb_power *power) * present->absent transition implies an online->offline transition * and will trigger the VBUS_REMOVAL IRQ. */ - if (power->axp20x_id >= AXP221_ID && !power->online) + if (power->axp_data->vbus_needs_polling && !power->online) return true; return false; @@ -121,60 +124,6 @@ out: mod_delayed_work(system_power_efficient_wq, &power->vbus_detect, DEBOUNCE_TIME); } -static int axp20x_get_current_max(struct axp20x_usb_power *power, int *val) -{ - unsigned int v; - int ret = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v); - - if (ret) - return ret; - - switch (v & AXP20X_VBUS_CLIMIT_MASK) { - case AXP20X_VBUS_CLIMIT_100mA: - if (power->axp20x_id == AXP221_ID) - *val = -1; /* No 100mA limit */ - else - *val = 100000; - break; - case AXP20X_VBUS_CLIMIT_500mA: - *val = 500000; - break; - case AXP20X_VBUS_CLIMIT_900mA: - *val = 900000; - break; - case AXP20X_VBUS_CLIMIT_NONE: - *val = -1; - break; - } - - return 0; -} - -static int axp813_get_current_max(struct axp20x_usb_power *power, int *val) -{ - unsigned int v; - int ret = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v); - - if (ret) - return ret; - - switch (v & AXP20X_VBUS_CLIMIT_MASK) { - case AXP813_VBUS_CLIMIT_900mA: - *val = 900000; - break; - case AXP813_VBUS_CLIMIT_1500mA: - *val = 1500000; - break; - case AXP813_VBUS_CLIMIT_2000mA: - *val = 2000000; - break; - case AXP813_VBUS_CLIMIT_2500mA: - *val = 2500000; - break; - } - return 0; -} - static int axp20x_usb_power_get_property(struct power_supply *psy, enum power_supply_property psp, union power_supply_propval *val) { @@ -213,9 +162,12 @@ static int axp20x_usb_power_get_property(struct power_supply *psy, val->intval = ret * 1700; /* 1 step = 1.7 mV */ return 0; case POWER_SUPPLY_PROP_CURRENT_MAX: - if (power->axp20x_id == AXP813_ID) - return axp813_get_current_max(power, &val->intval); - return axp20x_get_current_max(power, &val->intval); + ret = regmap_field_read(power->curr_lim_fld, &v); + if (ret) + return ret; + + val->intval = power->axp_data->curr_lim_table[v]; + return 0; case POWER_SUPPLY_PROP_CURRENT_NOW: if (IS_ENABLED(CONFIG_AXP20X_ADC)) { ret = iio_read_channel_processed(power->vbus_i, @@ -256,16 +208,15 @@ static int axp20x_usb_power_get_property(struct power_supply *psy, val->intval = POWER_SUPPLY_HEALTH_GOOD; - if (power->axp20x_id == AXP202_ID) { - ret = regmap_read(power->regmap, - AXP20X_USB_OTG_STATUS, &v); + if (power->vbus_valid_bit) { + ret = regmap_field_read(power->vbus_valid_bit, &v); if (ret) return ret; - if (!(v & AXP20X_USB_STATUS_VBUS_VALID)) - val->intval = - POWER_SUPPLY_HEALTH_UNSPEC_FAILURE; + if (v == 0) + val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE; } + break; case POWER_SUPPLY_PROP_PRESENT: val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_PRESENT); @@ -280,16 +231,6 @@ static int axp20x_usb_power_get_property(struct power_supply *psy, return 0; } -static int axp813_usb_power_set_online(struct axp20x_usb_power *power, - int intval) -{ - int val = !intval << AXP20X_VBUS_PATH_SEL_OFFSET; - - return regmap_update_bits(power->regmap, - AXP20X_VBUS_IPSOUT_MGMT, - AXP20X_VBUS_PATH_SEL, val); -} - static int axp20x_usb_power_set_voltage_min(struct axp20x_usb_power *power, int intval) { @@ -316,50 +257,17 @@ static int axp20x_usb_power_set_voltage_min(struct axp20x_usb_power *power, return -EINVAL; } -static int axp813_usb_power_set_current_max(struct axp20x_usb_power *power, - int intval) +static int axp20x_usb_power_set_current_max(struct axp20x_usb_power *power, int intval) { - int val; + const unsigned int max = GENMASK(power->axp_data->curr_lim_fld.msb, + power->axp_data->curr_lim_fld.lsb); - switch (intval) { - case 900000: - return regmap_update_bits(power->regmap, - AXP20X_VBUS_IPSOUT_MGMT, - AXP20X_VBUS_CLIMIT_MASK, - AXP813_VBUS_CLIMIT_900mA); - case 1500000: - case 2000000: - case 2500000: - val = (intval - 1000000) / 500000; - return regmap_update_bits(power->regmap, - AXP20X_VBUS_IPSOUT_MGMT, - AXP20X_VBUS_CLIMIT_MASK, val); - default: + if (intval == -1) return -EINVAL; - } - - return -EINVAL; -} - -static int axp20x_usb_power_set_current_max(struct axp20x_usb_power *power, - int intval) -{ - int val; - switch (intval) { - case 100000: - if (power->axp20x_id == AXP221_ID) - return -EINVAL; - fallthrough; - case 500000: - case 900000: - val = (900000 - intval) / 400000; - return regmap_update_bits(power->regmap, - AXP20X_VBUS_IPSOUT_MGMT, - AXP20X_VBUS_CLIMIT_MASK, val); - default: - return -EINVAL; - } + for (unsigned int i = 0; i <= max; ++i) + if (power->axp_data->curr_lim_table[i] == intval) + return regmap_field_write(power->curr_lim_fld, i); return -EINVAL; } @@ -372,17 +280,15 @@ static int axp20x_usb_power_set_property(struct power_supply *psy, switch (psp) { case POWER_SUPPLY_PROP_ONLINE: - if (power->axp20x_id != AXP813_ID) + if (!power->vbus_disable_bit) return -EINVAL; - return axp813_usb_power_set_online(power, val->intval); + + return regmap_field_write(power->vbus_disable_bit, !val->intval); case POWER_SUPPLY_PROP_VOLTAGE_MIN: return axp20x_usb_power_set_voltage_min(power, val->intval); case POWER_SUPPLY_PROP_CURRENT_MAX: - if (power->axp20x_id == AXP813_ID) - return axp813_usb_power_set_current_max(power, - val->intval); return axp20x_usb_power_set_current_max(power, val->intval); default: @@ -405,7 +311,7 @@ static int axp20x_usb_power_prop_writeable(struct power_supply *psy, * the VBUS input offline. */ if (psp == POWER_SUPPLY_PROP_ONLINE) - return power->axp20x_id == AXP813_ID; + return power->vbus_disable_bit != NULL; return psp == POWER_SUPPLY_PROP_VOLTAGE_MIN || psp == POWER_SUPPLY_PROP_CURRENT_MAX; @@ -461,39 +367,81 @@ static const char * const axp22x_irq_names[] = { "VBUS_REMOVAL", }; -struct axp_data { - const struct power_supply_desc *power_desc; - const char * const *irq_names; - unsigned int num_irq_names; - enum axp20x_variants axp20x_id; +static int axp192_usb_curr_lim_table[] = { + -1, + -1, + 500000, + 100000, +}; + +static int axp20x_usb_curr_lim_table[] = { + 900000, + 500000, + 100000, + -1, +}; + +static int axp221_usb_curr_lim_table[] = { + 900000, + 500000, + -1, + -1, +}; + +static int axp813_usb_curr_lim_table[] = { + 900000, + 1500000, + 2000000, + 2500000, +}; + +static const struct axp_data axp192_data = { + .power_desc = &axp20x_usb_power_desc, + .irq_names = axp20x_irq_names, + .num_irq_names = ARRAY_SIZE(axp20x_irq_names), + .curr_lim_table = axp192_usb_curr_lim_table, + .curr_lim_fld = REG_FIELD(AXP20X_VBUS_IPSOUT_MGMT, 0, 1), + .vbus_valid_bit = REG_FIELD(AXP192_USB_OTG_STATUS, 2, 2), + .vbus_mon_bit = REG_FIELD(AXP20X_VBUS_MON, 3, 3), }; static const struct axp_data axp202_data = { .power_desc = &axp20x_usb_power_desc, .irq_names = axp20x_irq_names, .num_irq_names = ARRAY_SIZE(axp20x_irq_names), - .axp20x_id = AXP202_ID, + .curr_lim_table = axp20x_usb_curr_lim_table, + .curr_lim_fld = REG_FIELD(AXP20X_VBUS_IPSOUT_MGMT, 0, 1), + .vbus_valid_bit = REG_FIELD(AXP20X_USB_OTG_STATUS, 2, 2), + .vbus_mon_bit = REG_FIELD(AXP20X_VBUS_MON, 3, 3), }; static const struct axp_data axp221_data = { .power_desc = &axp22x_usb_power_desc, .irq_names = axp22x_irq_names, .num_irq_names = ARRAY_SIZE(axp22x_irq_names), - .axp20x_id = AXP221_ID, + .curr_lim_table = axp221_usb_curr_lim_table, + .curr_lim_fld = REG_FIELD(AXP20X_VBUS_IPSOUT_MGMT, 0, 1), + .vbus_needs_polling = true, }; static const struct axp_data axp223_data = { .power_desc = &axp22x_usb_power_desc, .irq_names = axp22x_irq_names, .num_irq_names = ARRAY_SIZE(axp22x_irq_names), - .axp20x_id = AXP223_ID, + .curr_lim_table = axp20x_usb_curr_lim_table, + .curr_lim_fld = REG_FIELD(AXP20X_VBUS_IPSOUT_MGMT, 0, 1), + .vbus_needs_polling = true, }; static const struct axp_data axp813_data = { .power_desc = &axp22x_usb_power_desc, .irq_names = axp22x_irq_names, .num_irq_names = ARRAY_SIZE(axp22x_irq_names), - .axp20x_id = AXP813_ID, + .curr_lim_table = axp813_usb_curr_lim_table, + .curr_lim_fld = REG_FIELD(AXP20X_VBUS_IPSOUT_MGMT, 0, 1), + .usb_bc_en_bit = REG_FIELD(AXP288_BC_GLOBAL, 0, 0), + .vbus_disable_bit = REG_FIELD(AXP20X_VBUS_IPSOUT_MGMT, 7, 7), + .vbus_needs_polling = true, }; #ifdef CONFIG_PM_SLEEP @@ -565,6 +513,26 @@ static int configure_adc_registers(struct axp20x_usb_power *power) AXP20X_ADC_EN1_VBUS_VOLT); } +static int axp20x_regmap_field_alloc_optional(struct device *dev, + struct regmap *regmap, + struct reg_field fdesc, + struct regmap_field **fieldp) +{ + struct regmap_field *field; + + if (fdesc.reg == 0) { + *fieldp = NULL; + return 0; + } + + field = devm_regmap_field_alloc(dev, regmap, fdesc); + if (IS_ERR(field)) + return PTR_ERR(field); + + *fieldp = field; + return 0; +} + static int axp20x_usb_power_probe(struct platform_device *pdev) { struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent); @@ -591,20 +559,47 @@ static int axp20x_usb_power_probe(struct platform_device *pdev) platform_set_drvdata(pdev, power); - power->axp20x_id = axp_data->axp20x_id; + power->axp_data = axp_data; power->regmap = axp20x->regmap; power->num_irqs = axp_data->num_irq_names; + power->curr_lim_fld = devm_regmap_field_alloc(&pdev->dev, power->regmap, + axp_data->curr_lim_fld); + if (IS_ERR(power->curr_lim_fld)) + return PTR_ERR(power->curr_lim_fld); + + ret = axp20x_regmap_field_alloc_optional(&pdev->dev, power->regmap, + axp_data->vbus_valid_bit, + &power->vbus_valid_bit); + if (ret) + return ret; + + ret = axp20x_regmap_field_alloc_optional(&pdev->dev, power->regmap, + axp_data->vbus_mon_bit, + &power->vbus_mon_bit); + if (ret) + return ret; + + ret = axp20x_regmap_field_alloc_optional(&pdev->dev, power->regmap, + axp_data->usb_bc_en_bit, + &power->usb_bc_en_bit); + if (ret) + return ret; + + ret = axp20x_regmap_field_alloc_optional(&pdev->dev, power->regmap, + axp_data->vbus_disable_bit, + &power->vbus_disable_bit); + if (ret) + return ret; + ret = devm_delayed_work_autocancel(&pdev->dev, &power->vbus_detect, axp20x_usb_power_poll_vbus); if (ret) return ret; - if (power->axp20x_id == AXP202_ID) { + if (power->vbus_mon_bit) { /* Enable vbus valid checking */ - ret = regmap_update_bits(power->regmap, AXP20X_VBUS_MON, - AXP20X_VBUS_MON_VBUS_VALID, - AXP20X_VBUS_MON_VBUS_VALID); + ret = regmap_field_write(power->vbus_mon_bit, 1); if (ret) return ret; @@ -617,10 +612,9 @@ static int axp20x_usb_power_probe(struct platform_device *pdev) return ret; } - if (power->axp20x_id == AXP813_ID) { + if (power->usb_bc_en_bit) { /* Enable USB Battery Charging specification detection */ - ret = regmap_update_bits(axp20x->regmap, AXP288_BC_GLOBAL, - AXP813_BC_EN, AXP813_BC_EN); + ret = regmap_field_write(power->usb_bc_en_bit, 1); if (ret) return ret; } @@ -659,6 +653,9 @@ static int axp20x_usb_power_probe(struct platform_device *pdev) static const struct of_device_id axp20x_usb_power_match[] = { { + .compatible = "x-powers,axp192-usb-power-supply", + .data = &axp192_data, + }, { .compatible = "x-powers,axp202-usb-power-supply", .data = &axp202_data, }, { diff --git a/drivers/power/supply/bd99954-charger.c b/drivers/power/supply/bd99954-charger.c index 250362e15c98..086dcf4033c1 100644 --- a/drivers/power/supply/bd99954-charger.c +++ b/drivers/power/supply/bd99954-charger.c @@ -1077,7 +1077,7 @@ static struct i2c_driver bd9995x_driver = { .name = "bd9995x-charger", .of_match_table = bd9995x_of_match, }, - .probe_new = bd9995x_probe, + .probe = bd9995x_probe, }; module_i2c_driver(bd9995x_driver); diff --git a/drivers/power/supply/bq2415x_charger.c b/drivers/power/supply/bq2415x_charger.c index 349b69d634e6..6a4798a62588 100644 --- a/drivers/power/supply/bq2415x_charger.c +++ b/drivers/power/supply/bq2415x_charger.c @@ -1780,7 +1780,7 @@ static struct i2c_driver bq2415x_driver = { .of_match_table = of_match_ptr(bq2415x_of_match_table), .acpi_match_table = ACPI_PTR(bq2415x_i2c_acpi_match), }, - .probe_new = bq2415x_probe, + .probe = bq2415x_probe, .remove = bq2415x_remove, .id_table = bq2415x_i2c_id_table, }; diff --git a/drivers/power/supply/bq24190_charger.c b/drivers/power/supply/bq24190_charger.c index dc33f00fcc06..ef8235848f56 100644 --- a/drivers/power/supply/bq24190_charger.c +++ b/drivers/power/supply/bq24190_charger.c @@ -2034,7 +2034,7 @@ static const struct of_device_id bq24190_of_match[] = { MODULE_DEVICE_TABLE(of, bq24190_of_match); static struct i2c_driver bq24190_driver = { - .probe_new = bq24190_probe, + .probe = bq24190_probe, .remove = bq24190_remove, .shutdown = bq24190_shutdown, .id_table = bq24190_i2c_ids, diff --git a/drivers/power/supply/bq24257_charger.c b/drivers/power/supply/bq24257_charger.c index 45e4ba30da98..2852860abf86 100644 --- a/drivers/power/supply/bq24257_charger.c +++ b/drivers/power/supply/bq24257_charger.c @@ -1165,7 +1165,7 @@ static struct i2c_driver bq24257_driver = { .acpi_match_table = ACPI_PTR(bq24257_acpi_match), .pm = &bq24257_pm, }, - .probe_new = bq24257_probe, + .probe = bq24257_probe, .remove = bq24257_remove, .id_table = bq24257_i2c_ids, }; diff --git a/drivers/power/supply/bq24735-charger.c b/drivers/power/supply/bq24735-charger.c index cfca3a82d5a8..8efceeae864c 100644 --- a/drivers/power/supply/bq24735-charger.c +++ b/drivers/power/supply/bq24735-charger.c @@ -505,7 +505,7 @@ static struct i2c_driver bq24735_charger_driver = { .name = "bq24735-charger", .of_match_table = bq24735_match_ids, }, - .probe_new = bq24735_charger_probe, + .probe = bq24735_charger_probe, .id_table = bq24735_charger_id, }; diff --git a/drivers/power/supply/bq2515x_charger.c b/drivers/power/supply/bq2515x_charger.c index da224ae8dc61..1dbacc9b015d 100644 --- a/drivers/power/supply/bq2515x_charger.c +++ b/drivers/power/supply/bq2515x_charger.c @@ -1158,7 +1158,7 @@ static struct i2c_driver bq2515x_driver = { .name = "bq2515x-charger", .of_match_table = bq2515x_of_match, }, - .probe_new = bq2515x_probe, + .probe = bq2515x_probe, .id_table = bq2515x_i2c_ids, }; module_i2c_driver(bq2515x_driver); diff --git a/drivers/power/supply/bq256xx_charger.c b/drivers/power/supply/bq256xx_charger.c index e624834ae66c..82d3cd5ee2f9 100644 --- a/drivers/power/supply/bq256xx_charger.c +++ b/drivers/power/supply/bq256xx_charger.c @@ -41,6 +41,9 @@ #define BQ256XX_IINDPM_MAX_uA 3200000 #define BQ256XX_IINDPM_DEF_uA 2400000 +#define BQ256XX_TS_IGNORE BIT(6) +#define BQ256XX_TS_IGNORE_SHIFT 6 + #define BQ256XX_VINDPM_MASK GENMASK(3, 0) #define BQ256XX_VINDPM_STEP_uV 100000 #define BQ256XX_VINDPM_OFFSET_uV 3900000 @@ -156,6 +159,7 @@ * @vindpm: input voltage limit * @ichg_max: maximum fast charge current * @vbatreg_max: maximum charge voltage + * @ts_ignore: TS_IGNORE flag */ struct bq256xx_init_data { u32 ichg; @@ -166,6 +170,7 @@ struct bq256xx_init_data { u32 vindpm; u32 ichg_max; u32 vbatreg_max; + bool ts_ignore; }; /** @@ -263,6 +268,7 @@ struct bq256xx_device { * @bq256xx_set_iprechg: pointer to instance specific set_iprechg function * @bq256xx_set_vindpm: pointer to instance specific set_vindpm function * @bq256xx_set_charge_type: pointer to instance specific set_charge_type function + * @bq256xx_set_ts_ignore: pointer to instance specific set_ts_ignore function * * @bq256xx_def_ichg: default ichg value in microamps * @bq256xx_def_iindpm: default iindpm value in microamps @@ -295,6 +301,7 @@ struct bq256xx_chip_info { int (*bq256xx_set_iprechg)(struct bq256xx_device *bq, int iprechg); int (*bq256xx_set_vindpm)(struct bq256xx_device *bq, int vindpm); int (*bq256xx_set_charge_type)(struct bq256xx_device *bq, int type); + int (*bq256xx_set_ts_ignore)(struct bq256xx_device *bq, bool ts_ignore); int bq256xx_def_ichg; int bq256xx_def_iindpm; @@ -696,6 +703,12 @@ static int bq25601d_set_chrg_volt(struct bq256xx_device *bq, int vbatreg) BQ256XX_VBATREG_BIT_SHIFT); } +static int bq256xx_set_ts_ignore(struct bq256xx_device *bq, bool ts_ignore) +{ + return regmap_update_bits(bq->regmap, BQ256XX_INPUT_CURRENT_LIMIT, + BQ256XX_TS_IGNORE, (ts_ignore ? 1 : 0) << BQ256XX_TS_IGNORE_SHIFT); +} + static int bq256xx_get_prechrg_curr(struct bq256xx_device *bq) { unsigned int prechg_and_term_curr_lim; @@ -1312,6 +1325,7 @@ static const struct bq256xx_chip_info bq256xx_chip_info_tbl[] = { .bq256xx_get_iterm = bq256xx_get_term_curr, .bq256xx_get_iprechg = bq256xx_get_prechrg_curr, .bq256xx_get_vindpm = bq256xx_get_input_volt_lim, + .bq256xx_set_ts_ignore = NULL, .bq256xx_set_ichg = bq256xx_set_ichg_curr, .bq256xx_set_iindpm = bq256xx_set_input_curr_lim, @@ -1351,6 +1365,7 @@ static const struct bq256xx_chip_info bq256xx_chip_info_tbl[] = { .bq256xx_set_iprechg = bq256xx_set_prechrg_curr, .bq256xx_set_vindpm = bq256xx_set_input_volt_lim, .bq256xx_set_charge_type = bq256xx_set_charge_type, + .bq256xx_set_ts_ignore = NULL, .bq256xx_def_ichg = BQ2560X_ICHG_DEF_uA, .bq256xx_def_iindpm = BQ256XX_IINDPM_DEF_uA, @@ -1382,6 +1397,7 @@ static const struct bq256xx_chip_info bq256xx_chip_info_tbl[] = { .bq256xx_set_iprechg = bq256xx_set_prechrg_curr, .bq256xx_set_vindpm = bq256xx_set_input_volt_lim, .bq256xx_set_charge_type = bq256xx_set_charge_type, + .bq256xx_set_ts_ignore = NULL, .bq256xx_def_ichg = BQ2560X_ICHG_DEF_uA, .bq256xx_def_iindpm = BQ256XX_IINDPM_DEF_uA, @@ -1413,6 +1429,7 @@ static const struct bq256xx_chip_info bq256xx_chip_info_tbl[] = { .bq256xx_set_iprechg = bq256xx_set_prechrg_curr, .bq256xx_set_vindpm = bq256xx_set_input_volt_lim, .bq256xx_set_charge_type = bq256xx_set_charge_type, + .bq256xx_set_ts_ignore = NULL, .bq256xx_def_ichg = BQ2560X_ICHG_DEF_uA, .bq256xx_def_iindpm = BQ256XX_IINDPM_DEF_uA, @@ -1444,6 +1461,7 @@ static const struct bq256xx_chip_info bq256xx_chip_info_tbl[] = { .bq256xx_set_iprechg = bq256xx_set_prechrg_curr, .bq256xx_set_vindpm = bq256xx_set_input_volt_lim, .bq256xx_set_charge_type = bq256xx_set_charge_type, + .bq256xx_set_ts_ignore = bq256xx_set_ts_ignore, .bq256xx_def_ichg = BQ25611D_ICHG_DEF_uA, .bq256xx_def_iindpm = BQ256XX_IINDPM_DEF_uA, @@ -1475,6 +1493,7 @@ static const struct bq256xx_chip_info bq256xx_chip_info_tbl[] = { .bq256xx_set_iprechg = bq25618_619_set_prechrg_curr, .bq256xx_set_vindpm = bq256xx_set_input_volt_lim, .bq256xx_set_charge_type = bq256xx_set_charge_type, + .bq256xx_set_ts_ignore = bq256xx_set_ts_ignore, .bq256xx_def_ichg = BQ25618_ICHG_DEF_uA, .bq256xx_def_iindpm = BQ256XX_IINDPM_DEF_uA, @@ -1506,6 +1525,7 @@ static const struct bq256xx_chip_info bq256xx_chip_info_tbl[] = { .bq256xx_set_iprechg = bq25618_619_set_prechrg_curr, .bq256xx_set_vindpm = bq256xx_set_input_volt_lim, .bq256xx_set_charge_type = bq256xx_set_charge_type, + .bq256xx_set_ts_ignore = bq256xx_set_ts_ignore, .bq256xx_def_ichg = BQ25618_ICHG_DEF_uA, .bq256xx_def_iindpm = BQ256XX_IINDPM_DEF_uA, @@ -1622,6 +1642,12 @@ static int bq256xx_hw_init(struct bq256xx_device *bq) if (ret) return ret; + if (bq->chip_info->bq256xx_set_ts_ignore) { + ret = bq->chip_info->bq256xx_set_ts_ignore(bq, bq->init_data.ts_ignore); + if (ret) + return ret; + } + power_supply_put_battery_info(bq->charger, bat_info); return 0; @@ -1656,6 +1682,8 @@ static int bq256xx_parse_dt(struct bq256xx_device *bq, if (ret) bq->init_data.iindpm = bq->chip_info->bq256xx_def_iindpm; + bq->init_data.ts_ignore = device_property_read_bool(bq->dev, "ti,no-thermistor"); + return 0; } @@ -1784,7 +1812,7 @@ static struct i2c_driver bq256xx_driver = { .of_match_table = bq256xx_of_match, .acpi_match_table = bq256xx_acpi_match, }, - .probe_new = bq256xx_probe, + .probe = bq256xx_probe, .id_table = bq256xx_i2c_ids, }; module_i2c_driver(bq256xx_driver); diff --git a/drivers/power/supply/bq25890_charger.c b/drivers/power/supply/bq25890_charger.c index f8636cf86505..03fa11a1c9b6 100644 --- a/drivers/power/supply/bq25890_charger.c +++ b/drivers/power/supply/bq25890_charger.c @@ -1649,7 +1649,7 @@ static struct i2c_driver bq25890_driver = { .acpi_match_table = ACPI_PTR(bq25890_acpi_match), .pm = &bq25890_pm, }, - .probe_new = bq25890_probe, + .probe = bq25890_probe, .remove = bq25890_remove, .shutdown = bq25890_shutdown, .id_table = bq25890_i2c_ids, diff --git a/drivers/power/supply/bq25980_charger.c b/drivers/power/supply/bq25980_charger.c index a59d9762bc91..d8411722266f 100644 --- a/drivers/power/supply/bq25980_charger.c +++ b/drivers/power/supply/bq25980_charger.c @@ -1287,7 +1287,7 @@ static struct i2c_driver bq25980_driver = { .name = "bq25980-charger", .of_match_table = bq25980_of_match, }, - .probe_new = bq25980_probe, + .probe = bq25980_probe, .id_table = bq25980_i2c_ids, }; module_i2c_driver(bq25980_driver); diff --git a/drivers/power/supply/bq27xxx_battery_i2c.c b/drivers/power/supply/bq27xxx_battery_i2c.c index 6d3c74876339..9b5475590518 100644 --- a/drivers/power/supply/bq27xxx_battery_i2c.c +++ b/drivers/power/supply/bq27xxx_battery_i2c.c @@ -296,7 +296,7 @@ static struct i2c_driver bq27xxx_battery_i2c_driver = { .name = "bq27xxx-battery", .of_match_table = of_match_ptr(bq27xxx_battery_i2c_of_match_table), }, - .probe_new = bq27xxx_battery_i2c_probe, + .probe = bq27xxx_battery_i2c_probe, .remove = bq27xxx_battery_i2c_remove, .id_table = bq27xxx_i2c_id_table, }; diff --git a/drivers/power/supply/cros_peripheral_charger.c b/drivers/power/supply/cros_peripheral_charger.c index 1379afd9698d..a204f2355be4 100644 --- a/drivers/power/supply/cros_peripheral_charger.c +++ b/drivers/power/supply/cros_peripheral_charger.c @@ -227,8 +227,7 @@ static int cros_pchg_get_prop(struct power_supply *psy, return 0; } -static int cros_pchg_event(const struct charger_data *charger, - unsigned long host_event) +static int cros_pchg_event(const struct charger_data *charger) { int i; @@ -256,7 +255,7 @@ static int cros_ec_notify(struct notifier_block *nb, if (!(host_event & EC_MKBP_PCHG_DEVICE_EVENT)) return NOTIFY_DONE; - return cros_pchg_event(charger, host_event); + return cros_pchg_event(charger); } static int cros_pchg_probe(struct platform_device *pdev) @@ -281,6 +280,8 @@ static int cros_pchg_probe(struct platform_device *pdev) charger->ec_dev = ec_dev; charger->ec_device = ec_device; + platform_set_drvdata(pdev, charger); + ret = cros_pchg_port_count(charger); if (ret <= 0) { /* @@ -349,9 +350,27 @@ static int cros_pchg_probe(struct platform_device *pdev) return 0; } +#ifdef CONFIG_PM_SLEEP +static int __maybe_unused cros_pchg_resume(struct device *dev) +{ + struct charger_data *charger = dev_get_drvdata(dev); + + /* + * Sync all ports on resume in case reports from EC are lost during + * the last suspend. + */ + cros_pchg_event(charger); + + return 0; +} +#endif + +static SIMPLE_DEV_PM_OPS(cros_pchg_pm_ops, NULL, cros_pchg_resume); + static struct platform_driver cros_pchg_driver = { .driver = { .name = DRV_NAME, + .pm = &cros_pchg_pm_ops, }, .probe = cros_pchg_probe }; diff --git a/drivers/power/supply/cw2015_battery.c b/drivers/power/supply/cw2015_battery.c index 473522b4326a..bb29e9ebd24a 100644 --- a/drivers/power/supply/cw2015_battery.c +++ b/drivers/power/supply/cw2015_battery.c @@ -747,7 +747,7 @@ static struct i2c_driver cw_bat_driver = { .of_match_table = cw2015_of_match, .pm = &cw_bat_pm_ops, }, - .probe_new = cw_bat_probe, + .probe = cw_bat_probe, .id_table = cw_bat_id_table, }; diff --git a/drivers/power/supply/ds2782_battery.c b/drivers/power/supply/ds2782_battery.c index 9b9619246902..85aa9c465aa4 100644 --- a/drivers/power/supply/ds2782_battery.c +++ b/drivers/power/supply/ds2782_battery.c @@ -458,7 +458,7 @@ static struct i2c_driver ds278x_battery_driver = { .name = "ds2782-battery", .pm = &ds278x_battery_pm_ops, }, - .probe_new = ds278x_battery_probe, + .probe = ds278x_battery_probe, .remove = ds278x_battery_remove, .id_table = ds278x_id, }; diff --git a/drivers/power/supply/ip5xxx_power.c b/drivers/power/supply/ip5xxx_power.c index 00221e9c0bfc..82263646ddc6 100644 --- a/drivers/power/supply/ip5xxx_power.c +++ b/drivers/power/supply/ip5xxx_power.c @@ -625,7 +625,7 @@ static const struct of_device_id ip5xxx_power_of_match[] = { MODULE_DEVICE_TABLE(of, ip5xxx_power_of_match); static struct i2c_driver ip5xxx_power_driver = { - .probe_new = ip5xxx_power_probe, + .probe = ip5xxx_power_probe, .driver = { .name = "ip5xxx-power", .of_match_table = ip5xxx_power_of_match, diff --git a/drivers/power/supply/lp8727_charger.c b/drivers/power/supply/lp8727_charger.c index dc42d354b892..0875391f7ac6 100644 --- a/drivers/power/supply/lp8727_charger.c +++ b/drivers/power/supply/lp8727_charger.c @@ -615,7 +615,7 @@ static struct i2c_driver lp8727_driver = { .name = "lp8727", .of_match_table = of_match_ptr(lp8727_dt_ids), }, - .probe_new = lp8727_probe, + .probe = lp8727_probe, .remove = lp8727_remove, .id_table = lp8727_ids, }; diff --git a/drivers/power/supply/ltc2941-battery-gauge.c b/drivers/power/supply/ltc2941-battery-gauge.c index d3fb42825983..cad39a8f829d 100644 --- a/drivers/power/supply/ltc2941-battery-gauge.c +++ b/drivers/power/supply/ltc2941-battery-gauge.c @@ -635,7 +635,7 @@ static struct i2c_driver ltc294x_driver = { .of_match_table = ltc294x_i2c_of_match, .pm = LTC294X_PM_OPS, }, - .probe_new = ltc294x_i2c_probe, + .probe = ltc294x_i2c_probe, .shutdown = ltc294x_i2c_shutdown, .id_table = ltc294x_i2c_id, }; diff --git a/drivers/power/supply/ltc4162-l-charger.c b/drivers/power/supply/ltc4162-l-charger.c index 285580845e2f..ec5b4a20ad43 100644 --- a/drivers/power/supply/ltc4162-l-charger.c +++ b/drivers/power/supply/ltc4162-l-charger.c @@ -915,7 +915,7 @@ static const struct of_device_id ltc4162l_of_match[] __maybe_unused = { MODULE_DEVICE_TABLE(of, ltc4162l_of_match); static struct i2c_driver ltc4162l_driver = { - .probe_new = ltc4162l_probe, + .probe = ltc4162l_probe, .alert = ltc4162l_alert, .id_table = ltc4162l_i2c_id_table, .driver = { diff --git a/drivers/power/supply/max14656_charger_detector.c b/drivers/power/supply/max14656_charger_detector.c index 0d0180fcfa63..fbdf12cf64eb 100644 --- a/drivers/power/supply/max14656_charger_detector.c +++ b/drivers/power/supply/max14656_charger_detector.c @@ -316,7 +316,7 @@ static struct i2c_driver max14656_i2c_driver = { .name = "max14656", .of_match_table = max14656_match_table, }, - .probe_new = max14656_probe, + .probe = max14656_probe, .id_table = max14656_id, }; module_i2c_driver(max14656_i2c_driver); diff --git a/drivers/power/supply/max17040_battery.c b/drivers/power/supply/max17040_battery.c index d1075959dd46..22ea7de47a53 100644 --- a/drivers/power/supply/max17040_battery.c +++ b/drivers/power/supply/max17040_battery.c @@ -599,7 +599,7 @@ static struct i2c_driver max17040_i2c_driver = { .of_match_table = max17040_of_match, .pm = MAX17040_PM_OPS, }, - .probe_new = max17040_probe, + .probe = max17040_probe, .id_table = max17040_id, }; module_i2c_driver(max17040_i2c_driver); diff --git a/drivers/power/supply/max17042_battery.c b/drivers/power/supply/max17042_battery.c index 89cabe8ed3b0..17ac2ab78c4e 100644 --- a/drivers/power/supply/max17042_battery.c +++ b/drivers/power/supply/max17042_battery.c @@ -499,11 +499,6 @@ static int max17042_property_is_writeable(struct power_supply *psy, return ret; } -static void max17042_external_power_changed(struct power_supply *psy) -{ - power_supply_changed(psy); -} - static int max17042_write_verify_reg(struct regmap *map, u8 reg, u32 value) { int retries = 8; @@ -1016,7 +1011,7 @@ static const struct power_supply_desc max17042_psy_desc = { .get_property = max17042_get_property, .set_property = max17042_set_property, .property_is_writeable = max17042_property_is_writeable, - .external_power_changed = max17042_external_power_changed, + .external_power_changed = power_supply_changed, .properties = max17042_battery_props, .num_properties = ARRAY_SIZE(max17042_battery_props), }; @@ -1220,7 +1215,7 @@ static struct i2c_driver max17042_i2c_driver = { .of_match_table = of_match_ptr(max17042_dt_match), .pm = &max17042_pm_ops, }, - .probe_new = max17042_probe, + .probe = max17042_probe, .id_table = max17042_id, }; module_i2c_driver(max17042_i2c_driver); diff --git a/drivers/power/supply/max77976_charger.c b/drivers/power/supply/max77976_charger.c index 4fed74511931..99659dc8f5a6 100644 --- a/drivers/power/supply/max77976_charger.c +++ b/drivers/power/supply/max77976_charger.c @@ -499,7 +499,7 @@ static struct i2c_driver max77976_driver = { .name = MAX77976_DRIVER_NAME, .of_match_table = max77976_of_id, }, - .probe_new = max77976_probe, + .probe = max77976_probe, .id_table = max77976_i2c_id, }; module_i2c_driver(max77976_driver); diff --git a/drivers/power/supply/power_supply_hwmon.c b/drivers/power/supply/power_supply_hwmon.c index a48aa4afb828..c97893d4c25e 100644 --- a/drivers/power/supply/power_supply_hwmon.c +++ b/drivers/power/supply/power_supply_hwmon.c @@ -293,7 +293,7 @@ static const struct hwmon_ops power_supply_hwmon_ops = { .read_string = power_supply_hwmon_read_string, }; -static const struct hwmon_channel_info *power_supply_hwmon_info[] = { +static const struct hwmon_channel_info * const power_supply_hwmon_info[] = { HWMON_CHANNEL_INFO(temp, HWMON_T_LABEL | HWMON_T_INPUT | diff --git a/drivers/power/supply/power_supply_leds.c b/drivers/power/supply/power_supply_leds.c index 0674483279d7..c7db29d5fcb8 100644 --- a/drivers/power/supply/power_supply_leds.c +++ b/drivers/power/supply/power_supply_leds.c @@ -22,8 +22,6 @@ static void power_supply_update_bat_leds(struct power_supply *psy) { union power_supply_propval status; - unsigned long delay_on = 0; - unsigned long delay_off = 0; if (power_supply_get_property(psy, POWER_SUPPLY_PROP_STATUS, &status)) return; @@ -43,8 +41,7 @@ static void power_supply_update_bat_leds(struct power_supply *psy) led_trigger_event(psy->charging_full_trig, LED_FULL); led_trigger_event(psy->charging_trig, LED_FULL); led_trigger_event(psy->full_trig, LED_OFF); - led_trigger_blink(psy->charging_blink_full_solid_trig, - &delay_on, &delay_off); + led_trigger_blink(psy->charging_blink_full_solid_trig, 0, 0); break; default: led_trigger_event(psy->charging_full_trig, LED_OFF); diff --git a/drivers/power/supply/qcom_pmi8998_charger.c b/drivers/power/supply/qcom_pmi8998_charger.c new file mode 100644 index 000000000000..d16c5ee17249 --- /dev/null +++ b/drivers/power/supply/qcom_pmi8998_charger.c @@ -0,0 +1,1059 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (c) 2016-2019 The Linux Foundation. All rights reserved. + * Copyright (c) 2023, Linaro Ltd. + * Author: Caleb Connolly <caleb.connolly@linaro.org> + * + * This driver is for the switch-mode battery charger and boost + * hardware found in pmi8998 and related PMICs. + */ + +#include <linux/bits.h> +#include <linux/devm-helpers.h> +#include <linux/iio/consumer.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/minmax.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/pm_wakeirq.h> +#include <linux/of.h> +#include <linux/power_supply.h> +#include <linux/regmap.h> +#include <linux/types.h> +#include <linux/workqueue.h> + +/* clang-format off */ +#define BATTERY_CHARGER_STATUS_1 0x06 +#define BVR_INITIAL_RAMP_BIT BIT(7) +#define CC_SOFT_TERMINATE_BIT BIT(6) +#define STEP_CHARGING_STATUS_SHIFT 3 +#define STEP_CHARGING_STATUS_MASK GENMASK(5, 3) +#define BATTERY_CHARGER_STATUS_MASK GENMASK(2, 0) + +#define BATTERY_CHARGER_STATUS_2 0x07 +#define INPUT_CURRENT_LIMITED_BIT BIT(7) +#define CHARGER_ERROR_STATUS_SFT_EXPIRE_BIT BIT(6) +#define CHARGER_ERROR_STATUS_BAT_OV_BIT BIT(5) +#define CHARGER_ERROR_STATUS_BAT_TERM_MISSING_BIT BIT(4) +#define BAT_TEMP_STATUS_MASK GENMASK(3, 0) +#define BAT_TEMP_STATUS_SOFT_LIMIT_MASK GENMASK(3, 2) +#define BAT_TEMP_STATUS_HOT_SOFT_LIMIT_BIT BIT(3) +#define BAT_TEMP_STATUS_COLD_SOFT_LIMIT_BIT BIT(2) +#define BAT_TEMP_STATUS_TOO_HOT_BIT BIT(1) +#define BAT_TEMP_STATUS_TOO_COLD_BIT BIT(0) + +#define BATTERY_CHARGER_STATUS_4 0x0A +#define CHARGE_CURRENT_POST_JEITA_MASK GENMASK(7, 0) + +#define BATTERY_CHARGER_STATUS_7 0x0D +#define ENABLE_TRICKLE_BIT BIT(7) +#define ENABLE_PRE_CHARGING_BIT BIT(6) +#define ENABLE_FAST_CHARGING_BIT BIT(5) +#define ENABLE_FULLON_MODE_BIT BIT(4) +#define TOO_COLD_ADC_BIT BIT(3) +#define TOO_HOT_ADC_BIT BIT(2) +#define HOT_SL_ADC_BIT BIT(1) +#define COLD_SL_ADC_BIT BIT(0) + +#define CHARGING_ENABLE_CMD 0x42 +#define CHARGING_ENABLE_CMD_BIT BIT(0) + +#define CHGR_CFG2 0x51 +#define CHG_EN_SRC_BIT BIT(7) +#define CHG_EN_POLARITY_BIT BIT(6) +#define PRETOFAST_TRANSITION_CFG_BIT BIT(5) +#define BAT_OV_ECC_BIT BIT(4) +#define I_TERM_BIT BIT(3) +#define AUTO_RECHG_BIT BIT(2) +#define EN_ANALOG_DROP_IN_VBATT_BIT BIT(1) +#define CHARGER_INHIBIT_BIT BIT(0) + +#define PRE_CHARGE_CURRENT_CFG 0x60 +#define PRE_CHARGE_CURRENT_SETTING_MASK GENMASK(5, 0) + +#define FAST_CHARGE_CURRENT_CFG 0x61 +#define FAST_CHARGE_CURRENT_SETTING_MASK GENMASK(7, 0) + +#define FLOAT_VOLTAGE_CFG 0x70 +#define FLOAT_VOLTAGE_SETTING_MASK GENMASK(7, 0) + +#define FG_UPDATE_CFG_2_SEL 0x7D +#define SOC_LT_OTG_THRESH_SEL_BIT BIT(3) +#define SOC_LT_CHG_RECHARGE_THRESH_SEL_BIT BIT(2) +#define VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT BIT(1) +#define IBT_LT_CHG_TERM_THRESH_SEL_BIT BIT(0) + +#define JEITA_EN_CFG 0x90 +#define JEITA_EN_HARDLIMIT_BIT BIT(4) +#define JEITA_EN_HOT_SL_FCV_BIT BIT(3) +#define JEITA_EN_COLD_SL_FCV_BIT BIT(2) +#define JEITA_EN_HOT_SL_CCC_BIT BIT(1) +#define JEITA_EN_COLD_SL_CCC_BIT BIT(0) + +#define INT_RT_STS 0x310 +#define TYPE_C_CHANGE_RT_STS_BIT BIT(7) +#define USBIN_ICL_CHANGE_RT_STS_BIT BIT(6) +#define USBIN_SOURCE_CHANGE_RT_STS_BIT BIT(5) +#define USBIN_PLUGIN_RT_STS_BIT BIT(4) +#define USBIN_OV_RT_STS_BIT BIT(3) +#define USBIN_UV_RT_STS_BIT BIT(2) +#define USBIN_LT_3P6V_RT_STS_BIT BIT(1) +#define USBIN_COLLAPSE_RT_STS_BIT BIT(0) + +#define OTG_CFG 0x153 +#define OTG_RESERVED_MASK GENMASK(7, 6) +#define DIS_OTG_ON_TLIM_BIT BIT(5) +#define QUICKSTART_OTG_FASTROLESWAP_BIT BIT(4) +#define INCREASE_DFP_TIME_BIT BIT(3) +#define ENABLE_OTG_IN_DEBUG_MODE_BIT BIT(2) +#define OTG_EN_SRC_CFG_BIT BIT(1) +#define CONCURRENT_MODE_CFG_BIT BIT(0) + +#define OTG_ENG_OTG_CFG 0x1C0 +#define ENG_BUCKBOOST_HALT1_8_MODE_BIT BIT(0) + +#define APSD_STATUS 0x307 +#define APSD_STATUS_7_BIT BIT(7) +#define HVDCP_CHECK_TIMEOUT_BIT BIT(6) +#define SLOW_PLUGIN_TIMEOUT_BIT BIT(5) +#define ENUMERATION_DONE_BIT BIT(4) +#define VADP_CHANGE_DONE_AFTER_AUTH_BIT BIT(3) +#define QC_AUTH_DONE_STATUS_BIT BIT(2) +#define QC_CHARGER_BIT BIT(1) +#define APSD_DTC_STATUS_DONE_BIT BIT(0) + +#define APSD_RESULT_STATUS 0x308 +#define ICL_OVERRIDE_LATCH_BIT BIT(7) +#define APSD_RESULT_STATUS_MASK GENMASK(6, 0) +#define QC_3P0_BIT BIT(6) +#define QC_2P0_BIT BIT(5) +#define FLOAT_CHARGER_BIT BIT(4) +#define DCP_CHARGER_BIT BIT(3) +#define CDP_CHARGER_BIT BIT(2) +#define OCP_CHARGER_BIT BIT(1) +#define SDP_CHARGER_BIT BIT(0) + +#define TYPE_C_STATUS_1 0x30B +#define UFP_TYPEC_MASK GENMASK(7, 5) +#define UFP_TYPEC_RDSTD_BIT BIT(7) +#define UFP_TYPEC_RD1P5_BIT BIT(6) +#define UFP_TYPEC_RD3P0_BIT BIT(5) +#define UFP_TYPEC_FMB_255K_BIT BIT(4) +#define UFP_TYPEC_FMB_301K_BIT BIT(3) +#define UFP_TYPEC_FMB_523K_BIT BIT(2) +#define UFP_TYPEC_FMB_619K_BIT BIT(1) +#define UFP_TYPEC_OPEN_OPEN_BIT BIT(0) + +#define TYPE_C_STATUS_2 0x30C +#define DFP_RA_OPEN_BIT BIT(7) +#define TIMER_STAGE_BIT BIT(6) +#define EXIT_UFP_MODE_BIT BIT(5) +#define EXIT_DFP_MODE_BIT BIT(4) +#define DFP_TYPEC_MASK GENMASK(3, 0) +#define DFP_RD_OPEN_BIT BIT(3) +#define DFP_RD_RA_VCONN_BIT BIT(2) +#define DFP_RD_RD_BIT BIT(1) +#define DFP_RA_RA_BIT BIT(0) + +#define TYPE_C_STATUS_3 0x30D +#define ENABLE_BANDGAP_BIT BIT(7) +#define U_USB_GND_NOVBUS_BIT BIT(6) +#define U_USB_FLOAT_NOVBUS_BIT BIT(5) +#define U_USB_GND_BIT BIT(4) +#define U_USB_FMB1_BIT BIT(3) +#define U_USB_FLOAT1_BIT BIT(2) +#define U_USB_FMB2_BIT BIT(1) +#define U_USB_FLOAT2_BIT BIT(0) + +#define TYPE_C_STATUS_4 0x30E +#define UFP_DFP_MODE_STATUS_BIT BIT(7) +#define TYPEC_VBUS_STATUS_BIT BIT(6) +#define TYPEC_VBUS_ERROR_STATUS_BIT BIT(5) +#define TYPEC_DEBOUNCE_DONE_STATUS_BIT BIT(4) +#define TYPEC_UFP_AUDIO_ADAPT_STATUS_BIT BIT(3) +#define TYPEC_VCONN_OVERCURR_STATUS_BIT BIT(2) +#define CC_ORIENTATION_BIT BIT(1) +#define CC_ATTACHED_BIT BIT(0) + +#define TYPE_C_STATUS_5 0x30F +#define TRY_SOURCE_FAILED_BIT BIT(6) +#define TRY_SINK_FAILED_BIT BIT(5) +#define TIMER_STAGE_2_BIT BIT(4) +#define TYPEC_LEGACY_CABLE_STATUS_BIT BIT(3) +#define TYPEC_NONCOMP_LEGACY_CABLE_STATUS_BIT BIT(2) +#define TYPEC_TRYSOURCE_DETECT_STATUS_BIT BIT(1) +#define TYPEC_TRYSINK_DETECT_STATUS_BIT BIT(0) + +#define CMD_APSD 0x341 +#define ICL_OVERRIDE_BIT BIT(1) +#define APSD_RERUN_BIT BIT(0) + +#define TYPE_C_CFG 0x358 +#define APSD_START_ON_CC_BIT BIT(7) +#define WAIT_FOR_APSD_BIT BIT(6) +#define FACTORY_MODE_DETECTION_EN_BIT BIT(5) +#define FACTORY_MODE_ICL_3A_4A_BIT BIT(4) +#define FACTORY_MODE_DIS_CHGING_CFG_BIT BIT(3) +#define SUSPEND_NON_COMPLIANT_CFG_BIT BIT(2) +#define VCONN_OC_CFG_BIT BIT(1) +#define TYPE_C_OR_U_USB_BIT BIT(0) + +#define TYPE_C_CFG_2 0x359 +#define TYPE_C_DFP_CURRSRC_MODE_BIT BIT(7) +#define DFP_CC_1P4V_OR_1P6V_BIT BIT(6) +#define VCONN_SOFTSTART_CFG_MASK GENMASK(5, 4) +#define EN_TRY_SOURCE_MODE_BIT BIT(3) +#define USB_FACTORY_MODE_ENABLE_BIT BIT(2) +#define TYPE_C_UFP_MODE_BIT BIT(1) +#define EN_80UA_180UA_CUR_SOURCE_BIT BIT(0) + +#define TYPE_C_CFG_3 0x35A +#define TVBUS_DEBOUNCE_BIT BIT(7) +#define TYPEC_LEGACY_CABLE_INT_EN_BIT BIT(6) +#define TYPEC_NONCOMPLIANT_LEGACY_CABLE_INT_EN_B BIT(5) +#define TYPEC_TRYSOURCE_DETECT_INT_EN_BIT BIT(4) +#define TYPEC_TRYSINK_DETECT_INT_EN_BIT BIT(3) +#define EN_TRYSINK_MODE_BIT BIT(2) +#define EN_LEGACY_CABLE_DETECTION_BIT BIT(1) +#define ALLOW_PD_DRING_UFP_TCCDB_BIT BIT(0) + +#define USBIN_OPTIONS_1_CFG 0x362 +#define CABLE_R_SEL_BIT BIT(7) +#define HVDCP_AUTH_ALG_EN_CFG_BIT BIT(6) +#define HVDCP_AUTONOMOUS_MODE_EN_CFG_BIT BIT(5) +#define INPUT_PRIORITY_BIT BIT(4) +#define AUTO_SRC_DETECT_BIT BIT(3) +#define HVDCP_EN_BIT BIT(2) +#define VADP_INCREMENT_VOLTAGE_LIMIT_BIT BIT(1) +#define VADP_TAPER_TIMER_EN_BIT BIT(0) + +#define USBIN_OPTIONS_2_CFG 0x363 +#define WIPWR_RST_EUD_CFG_BIT BIT(7) +#define SWITCHER_START_CFG_BIT BIT(6) +#define DCD_TIMEOUT_SEL_BIT BIT(5) +#define OCD_CURRENT_SEL_BIT BIT(4) +#define SLOW_PLUGIN_TIMER_EN_CFG_BIT BIT(3) +#define FLOAT_OPTIONS_MASK GENMASK(2, 0) +#define FLOAT_DIS_CHGING_CFG_BIT BIT(2) +#define SUSPEND_FLOAT_CFG_BIT BIT(1) +#define FORCE_FLOAT_SDP_CFG_BIT BIT(0) + +#define TAPER_TIMER_SEL_CFG 0x364 +#define TYPEC_SPARE_CFG_BIT BIT(7) +#define TYPEC_DRP_DFP_TIME_CFG_BIT BIT(5) +#define TAPER_TIMER_SEL_MASK GENMASK(1, 0) + +#define USBIN_LOAD_CFG 0x365 +#define USBIN_OV_CH_LOAD_OPTION_BIT BIT(7) +#define ICL_OVERRIDE_AFTER_APSD_BIT BIT(4) + +#define USBIN_ICL_OPTIONS 0x366 +#define CFG_USB3P0_SEL_BIT BIT(2) +#define USB51_MODE_BIT BIT(1) +#define USBIN_MODE_CHG_BIT BIT(0) + +#define TYPE_C_INTRPT_ENB_SOFTWARE_CTRL 0x368 +#define EXIT_SNK_BASED_ON_CC_BIT BIT(7) +#define VCONN_EN_ORIENTATION_BIT BIT(6) +#define TYPEC_VCONN_OVERCURR_INT_EN_BIT BIT(5) +#define VCONN_EN_SRC_BIT BIT(4) +#define VCONN_EN_VALUE_BIT BIT(3) +#define TYPEC_POWER_ROLE_CMD_MASK GENMASK(2, 0) +#define UFP_EN_CMD_BIT BIT(2) +#define DFP_EN_CMD_BIT BIT(1) +#define TYPEC_DISABLE_CMD_BIT BIT(0) + +#define USBIN_CURRENT_LIMIT_CFG 0x370 +#define USBIN_CURRENT_LIMIT_MASK GENMASK(7, 0) + +#define USBIN_AICL_OPTIONS_CFG 0x380 +#define SUSPEND_ON_COLLAPSE_USBIN_BIT BIT(7) +#define USBIN_AICL_HDC_EN_BIT BIT(6) +#define USBIN_AICL_START_AT_MAX_BIT BIT(5) +#define USBIN_AICL_RERUN_EN_BIT BIT(4) +#define USBIN_AICL_ADC_EN_BIT BIT(3) +#define USBIN_AICL_EN_BIT BIT(2) +#define USBIN_HV_COLLAPSE_RESPONSE_BIT BIT(1) +#define USBIN_LV_COLLAPSE_RESPONSE_BIT BIT(0) + +#define USBIN_5V_AICL_THRESHOLD_CFG 0x381 +#define USBIN_5V_AICL_THRESHOLD_CFG_MASK GENMASK(2, 0) + +#define USBIN_CONT_AICL_THRESHOLD_CFG 0x384 +#define USBIN_CONT_AICL_THRESHOLD_CFG_MASK GENMASK(5, 0) + +#define DC_ENG_SSUPPLY_CFG2 0x4C1 +#define ENG_SSUPPLY_IVREF_OTG_SS_MASK GENMASK(2, 0) +#define OTG_SS_SLOW 0x3 + +#define DCIN_AICL_REF_SEL_CFG 0x481 +#define DCIN_CONT_AICL_THRESHOLD_CFG_MASK GENMASK(5, 0) + +#define WI_PWR_OPTIONS 0x495 +#define CHG_OK_BIT BIT(7) +#define WIPWR_UVLO_IRQ_OPT_BIT BIT(6) +#define BUCK_HOLDOFF_ENABLE_BIT BIT(5) +#define CHG_OK_HW_SW_SELECT_BIT BIT(4) +#define WIPWR_RST_ENABLE_BIT BIT(3) +#define DCIN_WIPWR_IRQ_SELECT_BIT BIT(2) +#define AICL_SWITCH_ENABLE_BIT BIT(1) +#define ZIN_ICL_ENABLE_BIT BIT(0) + +#define ICL_STATUS 0x607 +#define INPUT_CURRENT_LIMIT_MASK GENMASK(7, 0) + +#define POWER_PATH_STATUS 0x60B +#define P_PATH_INPUT_SS_DONE_BIT BIT(7) +#define P_PATH_USBIN_SUSPEND_STS_BIT BIT(6) +#define P_PATH_DCIN_SUSPEND_STS_BIT BIT(5) +#define P_PATH_USE_USBIN_BIT BIT(4) +#define P_PATH_USE_DCIN_BIT BIT(3) +#define P_PATH_POWER_PATH_MASK GENMASK(2, 1) +#define P_PATH_VALID_INPUT_POWER_SOURCE_STS_BIT BIT(0) + +#define BARK_BITE_WDOG_PET 0x643 +#define BARK_BITE_WDOG_PET_BIT BIT(0) + +#define WD_CFG 0x651 +#define WATCHDOG_TRIGGER_AFP_EN_BIT BIT(7) +#define BARK_WDOG_INT_EN_BIT BIT(6) +#define BITE_WDOG_INT_EN_BIT BIT(5) +#define SFT_AFTER_WDOG_IRQ_MASK GENMASK(4, 3) +#define WDOG_IRQ_SFT_BIT BIT(2) +#define WDOG_TIMER_EN_ON_PLUGIN_BIT BIT(1) +#define WDOG_TIMER_EN_BIT BIT(0) + +#define SNARL_BARK_BITE_WD_CFG 0x653 +#define BITE_WDOG_DISABLE_CHARGING_CFG_BIT BIT(7) +#define SNARL_WDOG_TIMEOUT_MASK GENMASK(6, 4) +#define BARK_WDOG_TIMEOUT_MASK GENMASK(3, 2) +#define BITE_WDOG_TIMEOUT_MASK GENMASK(1, 0) + +#define AICL_RERUN_TIME_CFG 0x661 +#define AICL_RERUN_TIME_MASK GENMASK(1, 0) + +#define STAT_CFG 0x690 +#define STAT_SW_OVERRIDE_VALUE_BIT BIT(7) +#define STAT_SW_OVERRIDE_CFG_BIT BIT(6) +#define STAT_PARALLEL_OFF_DG_CFG_MASK GENMASK(5, 4) +#define STAT_POLARITY_CFG_BIT BIT(3) +#define STAT_PARALLEL_CFG_BIT BIT(2) +#define STAT_FUNCTION_CFG_BIT BIT(1) +#define STAT_IRQ_PULSING_EN_BIT BIT(0) + +#define SDP_CURRENT_UA 500000 +#define CDP_CURRENT_UA 1500000 +#define DCP_CURRENT_UA 1500000 +#define CURRENT_MAX_UA DCP_CURRENT_UA + +/* pmi8998 registers represent current in increments of 1/40th of an amp */ +#define CURRENT_SCALE_FACTOR 25000 +/* clang-format on */ + +enum charger_status { + TRICKLE_CHARGE = 0, + PRE_CHARGE, + FAST_CHARGE, + FULLON_CHARGE, + TAPER_CHARGE, + TERMINATE_CHARGE, + INHIBIT_CHARGE, + DISABLE_CHARGE, +}; + +struct smb2_register { + u16 addr; + u8 mask; + u8 val; +}; + +/** + * struct smb2_chip - smb2 chip structure + * @dev: Device reference for power_supply + * @name: The platform device name + * @base: Base address for smb2 registers + * @regmap: Register map + * @batt_info: Battery data from DT + * @status_change_work: Worker to handle plug/unplug events + * @cable_irq: USB plugin IRQ + * @wakeup_enabled: If the cable IRQ will cause a wakeup + * @usb_in_i_chan: USB_IN current measurement channel + * @usb_in_v_chan: USB_IN voltage measurement channel + * @chg_psy: Charger power supply instance + */ +struct smb2_chip { + struct device *dev; + const char *name; + unsigned int base; + struct regmap *regmap; + struct power_supply_battery_info *batt_info; + + struct delayed_work status_change_work; + int cable_irq; + bool wakeup_enabled; + + struct iio_channel *usb_in_i_chan; + struct iio_channel *usb_in_v_chan; + + struct power_supply *chg_psy; +}; + +static enum power_supply_property smb2_properties[] = { + POWER_SUPPLY_PROP_MANUFACTURER, + POWER_SUPPLY_PROP_MODEL_NAME, + POWER_SUPPLY_PROP_CURRENT_MAX, + POWER_SUPPLY_PROP_CURRENT_NOW, + POWER_SUPPLY_PROP_VOLTAGE_NOW, + POWER_SUPPLY_PROP_STATUS, + POWER_SUPPLY_PROP_HEALTH, + POWER_SUPPLY_PROP_ONLINE, + POWER_SUPPLY_PROP_USB_TYPE, + POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT, + POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT_MAX, +}; + +static enum power_supply_usb_type smb2_usb_types[] = { + POWER_SUPPLY_USB_TYPE_UNKNOWN, + POWER_SUPPLY_USB_TYPE_SDP, + POWER_SUPPLY_USB_TYPE_DCP, + POWER_SUPPLY_USB_TYPE_CDP, +}; + +static int smb2_get_prop_usb_online(struct smb2_chip *chip, int *val) +{ + unsigned int stat; + int rc; + + rc = regmap_read(chip->regmap, chip->base + POWER_PATH_STATUS, &stat); + if (rc < 0) { + dev_err(chip->dev, "Couldn't read power path status: %d\n", rc); + return rc; + } + + *val = (stat & P_PATH_USE_USBIN_BIT) && + (stat & P_PATH_VALID_INPUT_POWER_SOURCE_STS_BIT); + return 0; +} + +/* + * Qualcomm "automatic power source detection" aka APSD + * tells us what type of charger we're connected to. + */ +static int smb2_apsd_get_charger_type(struct smb2_chip *chip, int *val) +{ + unsigned int apsd_stat, stat; + int usb_online = 0; + int rc; + + rc = smb2_get_prop_usb_online(chip, &usb_online); + if (!usb_online) { + *val = POWER_SUPPLY_USB_TYPE_UNKNOWN; + return rc; + } + + rc = regmap_read(chip->regmap, chip->base + APSD_STATUS, &apsd_stat); + if (rc < 0) { + dev_err(chip->dev, "Failed to read apsd status, rc = %d", rc); + return rc; + } + if (!(apsd_stat & APSD_DTC_STATUS_DONE_BIT)) { + dev_dbg(chip->dev, "Apsd not ready"); + return -EAGAIN; + } + + rc = regmap_read(chip->regmap, chip->base + APSD_RESULT_STATUS, &stat); + if (rc < 0) { + dev_err(chip->dev, "Failed to read apsd result, rc = %d", rc); + return rc; + } + + stat &= APSD_RESULT_STATUS_MASK; + + if (stat & CDP_CHARGER_BIT) + *val = POWER_SUPPLY_USB_TYPE_CDP; + else if (stat & (DCP_CHARGER_BIT | OCP_CHARGER_BIT | FLOAT_CHARGER_BIT)) + *val = POWER_SUPPLY_USB_TYPE_DCP; + else /* SDP_CHARGER_BIT (or others) */ + *val = POWER_SUPPLY_USB_TYPE_SDP; + + return 0; +} + +static int smb2_get_prop_status(struct smb2_chip *chip, int *val) +{ + unsigned char stat[2]; + int usb_online = 0; + int rc; + + rc = smb2_get_prop_usb_online(chip, &usb_online); + if (!usb_online) { + *val = POWER_SUPPLY_STATUS_DISCHARGING; + return rc; + } + + rc = regmap_bulk_read(chip->regmap, + chip->base + BATTERY_CHARGER_STATUS_1, &stat, 2); + if (rc < 0) { + dev_err(chip->dev, "Failed to read charging status ret=%d\n", + rc); + return rc; + } + + if (stat[1] & CHARGER_ERROR_STATUS_BAT_OV_BIT) { + *val = POWER_SUPPLY_STATUS_NOT_CHARGING; + return 0; + } + + stat[0] = stat[0] & BATTERY_CHARGER_STATUS_MASK; + + switch (stat[0]) { + case TRICKLE_CHARGE: + case PRE_CHARGE: + case FAST_CHARGE: + case FULLON_CHARGE: + case TAPER_CHARGE: + *val = POWER_SUPPLY_STATUS_CHARGING; + return rc; + case DISABLE_CHARGE: + *val = POWER_SUPPLY_STATUS_NOT_CHARGING; + return rc; + case TERMINATE_CHARGE: + *val = POWER_SUPPLY_STATUS_FULL; + return rc; + case INHIBIT_CHARGE: + default: + *val = POWER_SUPPLY_STATUS_UNKNOWN; + return rc; + } +} + +static inline int smb2_get_current_limit(struct smb2_chip *chip, + unsigned int *val) +{ + int rc = regmap_read(chip->regmap, chip->base + ICL_STATUS, val); + + if (rc >= 0) + *val *= CURRENT_SCALE_FACTOR; + return rc; +} + +static int smb2_set_current_limit(struct smb2_chip *chip, unsigned int val) +{ + unsigned char val_raw; + + if (val > 4800000) { + dev_err(chip->dev, + "Can't set current limit higher than 4800000uA"); + return -EINVAL; + } + val_raw = val / CURRENT_SCALE_FACTOR; + + return regmap_write(chip->regmap, chip->base + USBIN_CURRENT_LIMIT_CFG, + val_raw); +} + +static void smb2_status_change_work(struct work_struct *work) +{ + unsigned int charger_type, current_ua; + int usb_online, count, rc; + struct smb2_chip *chip; + + chip = container_of(work, struct smb2_chip, status_change_work.work); + + smb2_get_prop_usb_online(chip, &usb_online); + if (!usb_online) + return; + + for (count = 0; count < 3; count++) { + dev_dbg(chip->dev, "get charger type retry %d\n", count); + rc = smb2_apsd_get_charger_type(chip, &charger_type); + if (rc != -EAGAIN) + break; + msleep(100); + } + + if (rc < 0 && rc != -EAGAIN) { + dev_err(chip->dev, "get charger type failed: %d\n", rc); + return; + } + + if (rc < 0) { + rc = regmap_update_bits(chip->regmap, chip->base + CMD_APSD, + APSD_RERUN_BIT, APSD_RERUN_BIT); + schedule_delayed_work(&chip->status_change_work, + msecs_to_jiffies(1000)); + dev_dbg(chip->dev, "get charger type failed, rerun apsd\n"); + return; + } + + switch (charger_type) { + case POWER_SUPPLY_USB_TYPE_CDP: + current_ua = CDP_CURRENT_UA; + break; + case POWER_SUPPLY_USB_TYPE_DCP: + current_ua = DCP_CURRENT_UA; + break; + case POWER_SUPPLY_USB_TYPE_SDP: + default: + current_ua = SDP_CURRENT_UA; + break; + } + + smb2_set_current_limit(chip, current_ua); + power_supply_changed(chip->chg_psy); +} + +static int smb2_get_iio_chan(struct smb2_chip *chip, struct iio_channel *chan, + int *val) +{ + int rc; + union power_supply_propval status; + + rc = power_supply_get_property(chip->chg_psy, POWER_SUPPLY_PROP_STATUS, + &status); + if (rc < 0 || status.intval != POWER_SUPPLY_STATUS_CHARGING) { + *val = 0; + return 0; + } + + if (IS_ERR(chan)) { + dev_err(chip->dev, "Failed to chan, err = %li", PTR_ERR(chan)); + return PTR_ERR(chan); + } + + return iio_read_channel_processed(chan, val); +} + +static int smb2_get_prop_health(struct smb2_chip *chip, int *val) +{ + int rc; + unsigned int stat; + + rc = regmap_read(chip->regmap, chip->base + BATTERY_CHARGER_STATUS_2, + &stat); + if (rc < 0) { + dev_err(chip->dev, "Couldn't read charger status rc=%d\n", rc); + return rc; + } + + switch (stat) { + case CHARGER_ERROR_STATUS_BAT_OV_BIT: + *val = POWER_SUPPLY_HEALTH_OVERVOLTAGE; + return 0; + case BAT_TEMP_STATUS_TOO_COLD_BIT: + *val = POWER_SUPPLY_HEALTH_COLD; + return 0; + case BAT_TEMP_STATUS_TOO_HOT_BIT: + *val = POWER_SUPPLY_HEALTH_OVERHEAT; + return 0; + case BAT_TEMP_STATUS_COLD_SOFT_LIMIT_BIT: + *val = POWER_SUPPLY_HEALTH_COOL; + return 0; + case BAT_TEMP_STATUS_HOT_SOFT_LIMIT_BIT: + *val = POWER_SUPPLY_HEALTH_WARM; + return 0; + default: + *val = POWER_SUPPLY_HEALTH_GOOD; + return 0; + } +} + +static int smb2_get_property(struct power_supply *psy, + enum power_supply_property psp, + union power_supply_propval *val) +{ + struct smb2_chip *chip = power_supply_get_drvdata(psy); + + switch (psp) { + case POWER_SUPPLY_PROP_MANUFACTURER: + val->strval = "Qualcomm"; + return 0; + case POWER_SUPPLY_PROP_MODEL_NAME: + val->strval = chip->name; + return 0; + case POWER_SUPPLY_PROP_CURRENT_MAX: + case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT: + return smb2_get_current_limit(chip, &val->intval); + case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT_MAX: + val->intval = DCP_CURRENT_UA; + return 0; + case POWER_SUPPLY_PROP_CURRENT_NOW: + return smb2_get_iio_chan(chip, chip->usb_in_i_chan, + &val->intval); + case POWER_SUPPLY_PROP_VOLTAGE_NOW: + return smb2_get_iio_chan(chip, chip->usb_in_v_chan, + &val->intval); + case POWER_SUPPLY_PROP_ONLINE: + return smb2_get_prop_usb_online(chip, &val->intval); + case POWER_SUPPLY_PROP_STATUS: + return smb2_get_prop_status(chip, &val->intval); + case POWER_SUPPLY_PROP_HEALTH: + return smb2_get_prop_health(chip, &val->intval); + case POWER_SUPPLY_PROP_USB_TYPE: + return smb2_apsd_get_charger_type(chip, &val->intval); + default: + dev_err(chip->dev, "invalid property: %d\n", psp); + return -EINVAL; + } +} + +static int smb2_set_property(struct power_supply *psy, + enum power_supply_property psp, + const union power_supply_propval *val) +{ + struct smb2_chip *chip = power_supply_get_drvdata(psy); + + switch (psp) { + case POWER_SUPPLY_PROP_CURRENT_MAX: + case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT: + return smb2_set_current_limit(chip, val->intval); + default: + dev_err(chip->dev, "No setter for property: %d\n", psp); + return -EINVAL; + } +} + +static int smb2_property_is_writable(struct power_supply *psy, + enum power_supply_property psp) +{ + switch (psp) { + case POWER_SUPPLY_PROP_CURRENT_MAX: + case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT: + return 1; + default: + return 0; + } +} + +static irqreturn_t smb2_handle_batt_overvoltage(int irq, void *data) +{ + struct smb2_chip *chip = data; + unsigned int status; + + regmap_read(chip->regmap, chip->base + BATTERY_CHARGER_STATUS_2, + &status); + + if (status & CHARGER_ERROR_STATUS_BAT_OV_BIT) { + /* The hardware stops charging automatically */ + dev_err(chip->dev, "battery overvoltage detected\n"); + power_supply_changed(chip->chg_psy); + } + + return IRQ_HANDLED; +} + +static irqreturn_t smb2_handle_usb_plugin(int irq, void *data) +{ + struct smb2_chip *chip = data; + + power_supply_changed(chip->chg_psy); + + schedule_delayed_work(&chip->status_change_work, + msecs_to_jiffies(1500)); + + return IRQ_HANDLED; +} + +static irqreturn_t smb2_handle_usb_icl_change(int irq, void *data) +{ + struct smb2_chip *chip = data; + + power_supply_changed(chip->chg_psy); + + return IRQ_HANDLED; +} + +static irqreturn_t smb2_handle_wdog_bark(int irq, void *data) +{ + struct smb2_chip *chip = data; + int rc; + + power_supply_changed(chip->chg_psy); + + rc = regmap_write(chip->regmap, BARK_BITE_WDOG_PET, + BARK_BITE_WDOG_PET_BIT); + if (rc < 0) + dev_err(chip->dev, "Couldn't pet the dog rc=%d\n", rc); + + return IRQ_HANDLED; +} + +static const struct power_supply_desc smb2_psy_desc = { + .name = "pmi8998_charger", + .type = POWER_SUPPLY_TYPE_USB, + .usb_types = smb2_usb_types, + .num_usb_types = ARRAY_SIZE(smb2_usb_types), + .properties = smb2_properties, + .num_properties = ARRAY_SIZE(smb2_properties), + .get_property = smb2_get_property, + .set_property = smb2_set_property, + .property_is_writeable = smb2_property_is_writable, +}; + +/* Init sequence derived from vendor downstream driver */ +static const struct smb2_register smb2_init_seq[] = { + { .addr = AICL_RERUN_TIME_CFG, .mask = AICL_RERUN_TIME_MASK, .val = 0 }, + /* + * By default configure us as an upstream facing port + * FIXME: This will be handled by the type-c driver + */ + { .addr = TYPE_C_INTRPT_ENB_SOFTWARE_CTRL, + .mask = TYPEC_POWER_ROLE_CMD_MASK | VCONN_EN_SRC_BIT | + VCONN_EN_VALUE_BIT, + .val = VCONN_EN_SRC_BIT }, + /* + * Disable Type-C factory mode and stay in Attached.SRC state when VCONN + * over-current happens + */ + { .addr = TYPE_C_CFG, + .mask = FACTORY_MODE_DETECTION_EN_BIT | VCONN_OC_CFG_BIT, + .val = 0 }, + /* Configure VBUS for software control */ + { .addr = OTG_CFG, .mask = OTG_EN_SRC_CFG_BIT, .val = 0 }, + /* + * Use VBAT to determine the recharge threshold when battery is full + * rather than the state of charge. + */ + { .addr = FG_UPDATE_CFG_2_SEL, + .mask = SOC_LT_CHG_RECHARGE_THRESH_SEL_BIT | + VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT, + .val = VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT }, + /* Enable charging */ + { .addr = USBIN_OPTIONS_1_CFG, .mask = HVDCP_EN_BIT, .val = 0 }, + { .addr = CHARGING_ENABLE_CMD, + .mask = CHARGING_ENABLE_CMD_BIT, + .val = CHARGING_ENABLE_CMD_BIT }, + /* + * Match downstream defaults + * CHG_EN_SRC_BIT - charger enable is controlled by software + * CHG_EN_POLARITY_BIT - polarity of charge enable pin when in HW control + * pulled low on OnePlus 6 and SHIFT6mq + * PRETOFAST_TRANSITION_CFG_BIT - + * BAT_OV_ECC_BIT - + * I_TERM_BIT - Current termination ?? 0 = enabled + * AUTO_RECHG_BIT - Enable automatic recharge when battery is full + * 0 = enabled + * EN_ANALOG_DROP_IN_VBATT_BIT + * CHARGER_INHIBIT_BIT - Inhibit charging based on battery voltage + * instead of ?? + */ + { .addr = CHGR_CFG2, + .mask = CHG_EN_SRC_BIT | CHG_EN_POLARITY_BIT | + PRETOFAST_TRANSITION_CFG_BIT | BAT_OV_ECC_BIT | I_TERM_BIT | + AUTO_RECHG_BIT | EN_ANALOG_DROP_IN_VBATT_BIT | + CHARGER_INHIBIT_BIT, + .val = CHARGER_INHIBIT_BIT }, + /* STAT pin software override, match downstream. Parallell charging? */ + { .addr = STAT_CFG, + .mask = STAT_SW_OVERRIDE_CFG_BIT, + .val = STAT_SW_OVERRIDE_CFG_BIT }, + /* Set the default SDP charger type to a 500ma USB 2.0 port */ + { .addr = USBIN_ICL_OPTIONS, + .mask = USB51_MODE_BIT | USBIN_MODE_CHG_BIT, + .val = USB51_MODE_BIT }, + /* Disable watchdog */ + { .addr = SNARL_BARK_BITE_WD_CFG, .mask = 0xff, .val = 0 }, + { .addr = WD_CFG, + .mask = WATCHDOG_TRIGGER_AFP_EN_BIT | WDOG_TIMER_EN_ON_PLUGIN_BIT | + BARK_WDOG_INT_EN_BIT, + .val = 0 }, + /* These bits aren't documented anywhere */ + { .addr = USBIN_5V_AICL_THRESHOLD_CFG, + .mask = USBIN_5V_AICL_THRESHOLD_CFG_MASK, + .val = 0x3 }, + { .addr = USBIN_CONT_AICL_THRESHOLD_CFG, + .mask = USBIN_CONT_AICL_THRESHOLD_CFG_MASK, + .val = 0x3 }, + /* + * Enable Automatic Input Current Limit, this will slowly ramp up the current + * When connected to a wall charger, and automatically stop when it detects + * the charger current limit (voltage drop?) or it reaches the programmed limit. + */ + { .addr = USBIN_AICL_OPTIONS_CFG, + .mask = USBIN_AICL_START_AT_MAX_BIT | USBIN_AICL_ADC_EN_BIT | + USBIN_AICL_EN_BIT | SUSPEND_ON_COLLAPSE_USBIN_BIT | + USBIN_HV_COLLAPSE_RESPONSE_BIT | + USBIN_LV_COLLAPSE_RESPONSE_BIT, + .val = USBIN_HV_COLLAPSE_RESPONSE_BIT | + USBIN_LV_COLLAPSE_RESPONSE_BIT | USBIN_AICL_EN_BIT }, + /* + * Set pre charge current to default, the OnePlus 6 bootloader + * sets this very conservatively. + */ + { .addr = PRE_CHARGE_CURRENT_CFG, + .mask = PRE_CHARGE_CURRENT_SETTING_MASK, + .val = 500000 / CURRENT_SCALE_FACTOR }, + /* + * This overrides all of the current limit options exposed to userspace + * and prevents the device from pulling more than ~1A. This is done + * to minimise potential fire hazard risks. + */ + { .addr = FAST_CHARGE_CURRENT_CFG, + .mask = FAST_CHARGE_CURRENT_SETTING_MASK, + .val = 1000000 / CURRENT_SCALE_FACTOR }, +}; + +static int smb2_init_hw(struct smb2_chip *chip) +{ + int rc, i; + + for (i = 0; i < ARRAY_SIZE(smb2_init_seq); i++) { + dev_dbg(chip->dev, "%d: Writing 0x%02x to 0x%02x\n", i, + smb2_init_seq[i].val, smb2_init_seq[i].addr); + rc = regmap_update_bits(chip->regmap, + chip->base + smb2_init_seq[i].addr, + smb2_init_seq[i].mask, + smb2_init_seq[i].val); + if (rc < 0) + return dev_err_probe(chip->dev, rc, + "%s: init command %d failed\n", + __func__, i); + } + + return 0; +} + +static int smb2_init_irq(struct smb2_chip *chip, int *irq, const char *name, + irqreturn_t (*handler)(int irq, void *data)) +{ + int irqnum; + int rc; + + irqnum = platform_get_irq_byname(to_platform_device(chip->dev), name); + if (irqnum < 0) + return dev_err_probe(chip->dev, irqnum, + "Couldn't get irq %s byname\n", name); + + rc = devm_request_threaded_irq(chip->dev, irqnum, NULL, handler, + IRQF_ONESHOT, name, chip); + if (rc < 0) + return dev_err_probe(chip->dev, rc, "Couldn't request irq %s\n", + name); + + if (irq) + *irq = irqnum; + + return 0; +} + +static int smb2_probe(struct platform_device *pdev) +{ + struct power_supply_config supply_config = {}; + struct power_supply_desc *desc; + struct smb2_chip *chip; + int rc, irq; + + chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL); + if (!chip) + return -ENOMEM; + + chip->dev = &pdev->dev; + chip->name = pdev->name; + + chip->regmap = dev_get_regmap(pdev->dev.parent, NULL); + if (!chip->regmap) + return dev_err_probe(chip->dev, -ENODEV, + "failed to locate the regmap\n"); + + rc = device_property_read_u32(chip->dev, "reg", &chip->base); + if (rc < 0) + return dev_err_probe(chip->dev, rc, + "Couldn't read base address\n"); + + chip->usb_in_v_chan = devm_iio_channel_get(chip->dev, "usbin_v"); + if (IS_ERR(chip->usb_in_v_chan)) + return dev_err_probe(chip->dev, PTR_ERR(chip->usb_in_v_chan), + "Couldn't get usbin_v IIO channel\n"); + + chip->usb_in_i_chan = devm_iio_channel_get(chip->dev, "usbin_i"); + if (IS_ERR(chip->usb_in_i_chan)) { + return dev_err_probe(chip->dev, PTR_ERR(chip->usb_in_i_chan), + "Couldn't get usbin_i IIO channel\n"); + } + + rc = smb2_init_hw(chip); + if (rc < 0) + return rc; + + supply_config.drv_data = chip; + supply_config.of_node = pdev->dev.of_node; + + desc = devm_kzalloc(chip->dev, sizeof(smb2_psy_desc), GFP_KERNEL); + memcpy(desc, &smb2_psy_desc, sizeof(smb2_psy_desc)); + desc->name = + devm_kasprintf(chip->dev, GFP_KERNEL, "%s-charger", + (const char *)device_get_match_data(chip->dev)); + + chip->chg_psy = + devm_power_supply_register(chip->dev, desc, &supply_config); + if (IS_ERR(chip->chg_psy)) + return dev_err_probe(chip->dev, PTR_ERR(chip->chg_psy), + "failed to register power supply\n"); + + rc = power_supply_get_battery_info(chip->chg_psy, &chip->batt_info); + if (rc) + return dev_err_probe(chip->dev, rc, + "Failed to get battery info\n"); + + rc = devm_delayed_work_autocancel(chip->dev, &chip->status_change_work, + smb2_status_change_work); + if (rc) + return dev_err_probe(chip->dev, rc, + "Failed to init status change work\n"); + + rc = (chip->batt_info->voltage_max_design_uv - 3487500) / 7500 + 1; + rc = regmap_update_bits(chip->regmap, chip->base + FLOAT_VOLTAGE_CFG, + FLOAT_VOLTAGE_SETTING_MASK, rc); + if (rc < 0) + return dev_err_probe(chip->dev, rc, "Couldn't set vbat max\n"); + + rc = smb2_init_irq(chip, &irq, "bat-ov", smb2_handle_batt_overvoltage); + if (rc < 0) + return rc; + + rc = smb2_init_irq(chip, &chip->cable_irq, "usb-plugin", + smb2_handle_usb_plugin); + if (rc < 0) + return rc; + + rc = smb2_init_irq(chip, &irq, "usbin-icl-change", + smb2_handle_usb_icl_change); + if (rc < 0) + return rc; + rc = smb2_init_irq(chip, &irq, "wdog-bark", smb2_handle_wdog_bark); + if (rc < 0) + return rc; + + rc = dev_pm_set_wake_irq(chip->dev, chip->cable_irq); + if (rc < 0) + return dev_err_probe(chip->dev, rc, "Couldn't set wake irq\n"); + + platform_set_drvdata(pdev, chip); + + /* Initialise charger state */ + schedule_delayed_work(&chip->status_change_work, 0); + + return 0; +} + +static const struct of_device_id smb2_match_id_table[] = { + { .compatible = "qcom,pmi8998-charger", .data = "pmi8998" }, + { .compatible = "qcom,pm660-charger", .data = "pm660" }, + { /* sentinal */ } +}; +MODULE_DEVICE_TABLE(of, smb2_match_id_table); + +static struct platform_driver qcom_spmi_smb2 = { + .probe = smb2_probe, + .driver = { + .name = "qcom-pmi8998/pm660-charger", + .of_match_table = smb2_match_id_table, + }, +}; + +module_platform_driver(qcom_spmi_smb2); + +MODULE_AUTHOR("Caleb Connolly <caleb.connolly@linaro.org>"); +MODULE_DESCRIPTION("Qualcomm SMB2 Charger Driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/power/supply/rk817_charger.c b/drivers/power/supply/rk817_charger.c index 1a2143641e66..8328bcea1a29 100644 --- a/drivers/power/supply/rk817_charger.c +++ b/drivers/power/supply/rk817_charger.c @@ -1134,7 +1134,7 @@ static int rk817_charger_probe(struct platform_device *pdev) &bat_info); if (ret) { return dev_err_probe(dev, ret, - "Unable to get battery info: %d\n", ret); + "Unable to get battery info\n"); } if ((bat_info->charge_full_design_uah <= 0) || diff --git a/drivers/power/supply/rt5033_battery.c b/drivers/power/supply/rt5033_battery.c index 5c04cf305219..d90b96df8e73 100644 --- a/drivers/power/supply/rt5033_battery.c +++ b/drivers/power/supply/rt5033_battery.c @@ -6,11 +6,33 @@ * Author: Beomho Seo <beomho.seo@samsung.com> */ +#include <linux/i2c.h> #include <linux/module.h> #include <linux/platform_device.h> #include <linux/power_supply.h> +#include <linux/regmap.h> #include <linux/mfd/rt5033-private.h> -#include <linux/mfd/rt5033.h> + +struct rt5033_battery { + struct i2c_client *client; + struct regmap *regmap; + struct power_supply *psy; +}; + +static int rt5033_battery_get_status(struct i2c_client *client) +{ + struct rt5033_battery *battery = i2c_get_clientdata(client); + union power_supply_propval val; + int ret; + + ret = power_supply_get_property_from_supplier(battery->psy, + POWER_SUPPLY_PROP_STATUS, + &val); + if (ret) + val.intval = POWER_SUPPLY_STATUS_UNKNOWN; + + return val.intval; +} static int rt5033_battery_get_capacity(struct i2c_client *client) { @@ -84,6 +106,9 @@ static int rt5033_battery_get_property(struct power_supply *psy, case POWER_SUPPLY_PROP_CAPACITY: val->intval = rt5033_battery_get_capacity(battery->client); break; + case POWER_SUPPLY_PROP_STATUS: + val->intval = rt5033_battery_get_status(battery->client); + break; default: return -EINVAL; } @@ -96,6 +121,7 @@ static enum power_supply_property rt5033_battery_props[] = { POWER_SUPPLY_PROP_VOLTAGE_OCV, POWER_SUPPLY_PROP_PRESENT, POWER_SUPPLY_PROP_CAPACITY, + POWER_SUPPLY_PROP_STATUS, }; static const struct regmap_config rt5033_battery_regmap_config = { @@ -117,7 +143,6 @@ static int rt5033_battery_probe(struct i2c_client *client) struct i2c_adapter *adapter = client->adapter; struct power_supply_config psy_cfg = {}; struct rt5033_battery *battery; - u32 ret; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE)) return -EIO; @@ -135,15 +160,14 @@ static int rt5033_battery_probe(struct i2c_client *client) } i2c_set_clientdata(client, battery); + psy_cfg.of_node = client->dev.of_node; psy_cfg.drv_data = battery; battery->psy = power_supply_register(&client->dev, &rt5033_battery_desc, &psy_cfg); - if (IS_ERR(battery->psy)) { - dev_err(&client->dev, "Failed to register power supply\n"); - ret = PTR_ERR(battery->psy); - return ret; - } + if (IS_ERR(battery->psy)) + return dev_err_probe(&client->dev, PTR_ERR(battery->psy), + "Failed to register power supply\n"); return 0; } @@ -172,7 +196,7 @@ static struct i2c_driver rt5033_battery_driver = { .name = "rt5033-battery", .of_match_table = rt5033_battery_of_match, }, - .probe_new = rt5033_battery_probe, + .probe = rt5033_battery_probe, .remove = rt5033_battery_remove, .id_table = rt5033_battery_id, }; diff --git a/drivers/power/supply/rt5033_charger.c b/drivers/power/supply/rt5033_charger.c new file mode 100644 index 000000000000..5218dfbf5e1b --- /dev/null +++ b/drivers/power/supply/rt5033_charger.c @@ -0,0 +1,472 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Battery charger driver for RT5033 + * + * Copyright (C) 2014 Samsung Electronics, Co., Ltd. + * Author: Beomho Seo <beomho.seo@samsung.com> + */ + +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/power_supply.h> +#include <linux/regmap.h> +#include <linux/mfd/rt5033-private.h> + +struct rt5033_charger_data { + unsigned int pre_uamp; + unsigned int pre_uvolt; + unsigned int const_uvolt; + unsigned int eoc_uamp; + unsigned int fast_uamp; +}; + +struct rt5033_charger { + struct device *dev; + struct regmap *regmap; + struct power_supply *psy; + struct rt5033_charger_data *chg; +}; + +static int rt5033_get_charger_state(struct rt5033_charger *charger) +{ + struct regmap *regmap = charger->regmap; + unsigned int reg_data; + int state; + + if (!regmap) + return POWER_SUPPLY_STATUS_UNKNOWN; + + regmap_read(regmap, RT5033_REG_CHG_STAT, ®_data); + + switch (reg_data & RT5033_CHG_STAT_MASK) { + case RT5033_CHG_STAT_DISCHARGING: + state = POWER_SUPPLY_STATUS_DISCHARGING; + break; + case RT5033_CHG_STAT_CHARGING: + state = POWER_SUPPLY_STATUS_CHARGING; + break; + case RT5033_CHG_STAT_FULL: + state = POWER_SUPPLY_STATUS_FULL; + break; + case RT5033_CHG_STAT_NOT_CHARGING: + state = POWER_SUPPLY_STATUS_NOT_CHARGING; + break; + default: + state = POWER_SUPPLY_STATUS_UNKNOWN; + } + + return state; +} + +static int rt5033_get_charger_type(struct rt5033_charger *charger) +{ + struct regmap *regmap = charger->regmap; + unsigned int reg_data; + int state; + + regmap_read(regmap, RT5033_REG_CHG_STAT, ®_data); + + switch (reg_data & RT5033_CHG_STAT_TYPE_MASK) { + case RT5033_CHG_STAT_TYPE_FAST: + state = POWER_SUPPLY_CHARGE_TYPE_FAST; + break; + case RT5033_CHG_STAT_TYPE_PRE: + state = POWER_SUPPLY_CHARGE_TYPE_TRICKLE; + break; + default: + state = POWER_SUPPLY_CHARGE_TYPE_NONE; + } + + return state; +} + +static int rt5033_get_charger_current_limit(struct rt5033_charger *charger) +{ + struct regmap *regmap = charger->regmap; + unsigned int state, reg_data, data; + + regmap_read(regmap, RT5033_REG_CHG_CTRL5, ®_data); + + state = (reg_data & RT5033_CHGCTRL5_ICHG_MASK) + >> RT5033_CHGCTRL5_ICHG_SHIFT; + + data = RT5033_CHARGER_FAST_CURRENT_MIN + + RT5033_CHARGER_FAST_CURRENT_STEP_NUM * state; + + return data; +} + +static int rt5033_get_charger_const_voltage(struct rt5033_charger *charger) +{ + struct regmap *regmap = charger->regmap; + unsigned int state, reg_data, data; + + regmap_read(regmap, RT5033_REG_CHG_CTRL2, ®_data); + + state = (reg_data & RT5033_CHGCTRL2_CV_MASK) + >> RT5033_CHGCTRL2_CV_SHIFT; + + data = RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MIN + + RT5033_CHARGER_CONST_VOLTAGE_STEP_NUM * state; + + return data; +} + +static inline int rt5033_init_const_charge(struct rt5033_charger *charger) +{ + struct rt5033_charger_data *chg = charger->chg; + int ret; + unsigned int val; + u8 reg_data; + + /* Set constant voltage mode */ + if (chg->const_uvolt < RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MIN || + chg->const_uvolt > RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MAX) { + dev_err(charger->dev, + "Value 'constant-charge-voltage-max-microvolt' out of range\n"); + return -EINVAL; + } + + if (chg->const_uvolt == RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MIN) + reg_data = 0x00; + else if (chg->const_uvolt == RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MAX) + reg_data = RT5033_CV_MAX_VOLTAGE; + else { + val = chg->const_uvolt; + val -= RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MIN; + val /= RT5033_CHARGER_CONST_VOLTAGE_STEP_NUM; + reg_data = val; + } + + ret = regmap_update_bits(charger->regmap, RT5033_REG_CHG_CTRL2, + RT5033_CHGCTRL2_CV_MASK, + reg_data << RT5033_CHGCTRL2_CV_SHIFT); + if (ret) { + dev_err(charger->dev, "Failed regmap update\n"); + return -EINVAL; + } + + /* Set end of charge current */ + if (chg->eoc_uamp < RT5033_CHARGER_EOC_MIN || + chg->eoc_uamp > RT5033_CHARGER_EOC_MAX) { + dev_err(charger->dev, + "Value 'charge-term-current-microamp' out of range\n"); + return -EINVAL; + } + + if (chg->eoc_uamp == RT5033_CHARGER_EOC_MIN) + reg_data = 0x01; + else if (chg->eoc_uamp == RT5033_CHARGER_EOC_MAX) + reg_data = 0x07; + else { + val = chg->eoc_uamp; + if (val < RT5033_CHARGER_EOC_REF) { + val -= RT5033_CHARGER_EOC_MIN; + val /= RT5033_CHARGER_EOC_STEP_NUM1; + reg_data = 0x01 + val; + } else if (val > RT5033_CHARGER_EOC_REF) { + val -= RT5033_CHARGER_EOC_REF; + val /= RT5033_CHARGER_EOC_STEP_NUM2; + reg_data = 0x04 + val; + } else { + reg_data = 0x04; + } + } + + ret = regmap_update_bits(charger->regmap, RT5033_REG_CHG_CTRL4, + RT5033_CHGCTRL4_EOC_MASK, reg_data); + if (ret) { + dev_err(charger->dev, "Failed regmap update\n"); + return -EINVAL; + } + + return 0; +} + +static inline int rt5033_init_fast_charge(struct rt5033_charger *charger) +{ + struct rt5033_charger_data *chg = charger->chg; + int ret; + unsigned int val; + u8 reg_data; + + /* Set limit input current */ + ret = regmap_update_bits(charger->regmap, RT5033_REG_CHG_CTRL1, + RT5033_CHGCTRL1_IAICR_MASK, RT5033_AICR_2000_MODE); + if (ret) { + dev_err(charger->dev, "Failed regmap update\n"); + return -EINVAL; + } + + /* Set fast-charge mode charging current */ + if (chg->fast_uamp < RT5033_CHARGER_FAST_CURRENT_MIN || + chg->fast_uamp > RT5033_CHARGER_FAST_CURRENT_MAX) { + dev_err(charger->dev, + "Value 'constant-charge-current-max-microamp' out of range\n"); + return -EINVAL; + } + + if (chg->fast_uamp == RT5033_CHARGER_FAST_CURRENT_MIN) + reg_data = 0x00; + else if (chg->fast_uamp == RT5033_CHARGER_FAST_CURRENT_MAX) + reg_data = RT5033_CHG_MAX_CURRENT; + else { + val = chg->fast_uamp; + val -= RT5033_CHARGER_FAST_CURRENT_MIN; + val /= RT5033_CHARGER_FAST_CURRENT_STEP_NUM; + reg_data = val; + } + + ret = regmap_update_bits(charger->regmap, RT5033_REG_CHG_CTRL5, + RT5033_CHGCTRL5_ICHG_MASK, + reg_data << RT5033_CHGCTRL5_ICHG_SHIFT); + if (ret) { + dev_err(charger->dev, "Failed regmap update\n"); + return -EINVAL; + } + + return 0; +} + +static inline int rt5033_init_pre_charge(struct rt5033_charger *charger) +{ + struct rt5033_charger_data *chg = charger->chg; + int ret; + unsigned int val; + u8 reg_data; + + /* Set pre-charge threshold voltage */ + if (chg->pre_uvolt < RT5033_CHARGER_PRE_THRESHOLD_LIMIT_MIN || + chg->pre_uvolt > RT5033_CHARGER_PRE_THRESHOLD_LIMIT_MAX) { + dev_err(charger->dev, + "Value 'precharge-upper-limit-microvolt' out of range\n"); + return -EINVAL; + } + + if (chg->pre_uvolt == RT5033_CHARGER_PRE_THRESHOLD_LIMIT_MIN) + reg_data = 0x00; + else if (chg->pre_uvolt == RT5033_CHARGER_PRE_THRESHOLD_LIMIT_MAX) + reg_data = 0x0f; + else { + val = chg->pre_uvolt; + val -= RT5033_CHARGER_PRE_THRESHOLD_LIMIT_MIN; + val /= RT5033_CHARGER_PRE_THRESHOLD_STEP_NUM; + reg_data = val; + } + + ret = regmap_update_bits(charger->regmap, RT5033_REG_CHG_CTRL5, + RT5033_CHGCTRL5_VPREC_MASK, reg_data); + if (ret) { + dev_err(charger->dev, "Failed regmap update\n"); + return -EINVAL; + } + + /* Set pre-charge mode charging current */ + if (chg->pre_uamp < RT5033_CHARGER_PRE_CURRENT_LIMIT_MIN || + chg->pre_uamp > RT5033_CHARGER_PRE_CURRENT_LIMIT_MAX) { + dev_err(charger->dev, + "Value 'precharge-current-microamp' out of range\n"); + return -EINVAL; + } + + if (chg->pre_uamp == RT5033_CHARGER_PRE_CURRENT_LIMIT_MIN) + reg_data = 0x00; + else if (chg->pre_uamp == RT5033_CHARGER_PRE_CURRENT_LIMIT_MAX) + reg_data = RT5033_CHG_MAX_PRE_CURRENT; + else { + val = chg->pre_uamp; + val -= RT5033_CHARGER_PRE_CURRENT_LIMIT_MIN; + val /= RT5033_CHARGER_PRE_CURRENT_STEP_NUM; + reg_data = val; + } + + ret = regmap_update_bits(charger->regmap, RT5033_REG_CHG_CTRL4, + RT5033_CHGCTRL4_IPREC_MASK, + reg_data << RT5033_CHGCTRL4_IPREC_SHIFT); + if (ret) { + dev_err(charger->dev, "Failed regmap update\n"); + return -EINVAL; + } + + return 0; +} + +static int rt5033_charger_reg_init(struct rt5033_charger *charger) +{ + int ret = 0; + + /* Enable charging termination */ + ret = regmap_update_bits(charger->regmap, RT5033_REG_CHG_CTRL1, + RT5033_CHGCTRL1_TE_EN_MASK, RT5033_TE_ENABLE); + if (ret) { + dev_err(charger->dev, "Failed to enable charging termination.\n"); + return -EINVAL; + } + + /* + * Disable minimum input voltage regulation (MIVR), this improves + * the charging performance. + */ + ret = regmap_update_bits(charger->regmap, RT5033_REG_CHG_CTRL4, + RT5033_CHGCTRL4_MIVR_MASK, RT5033_CHARGER_MIVR_DISABLE); + if (ret) { + dev_err(charger->dev, "Failed to disable MIVR.\n"); + return -EINVAL; + } + + ret = rt5033_init_pre_charge(charger); + if (ret) + return ret; + + ret = rt5033_init_fast_charge(charger); + if (ret) + return ret; + + ret = rt5033_init_const_charge(charger); + if (ret) + return ret; + + return 0; +} + +static enum power_supply_property rt5033_charger_props[] = { + POWER_SUPPLY_PROP_STATUS, + POWER_SUPPLY_PROP_CHARGE_TYPE, + POWER_SUPPLY_PROP_CURRENT_MAX, + POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE, + POWER_SUPPLY_PROP_MODEL_NAME, + POWER_SUPPLY_PROP_MANUFACTURER, + POWER_SUPPLY_PROP_ONLINE, +}; + +static int rt5033_charger_get_property(struct power_supply *psy, + enum power_supply_property psp, + union power_supply_propval *val) +{ + struct rt5033_charger *charger = power_supply_get_drvdata(psy); + + switch (psp) { + case POWER_SUPPLY_PROP_STATUS: + val->intval = rt5033_get_charger_state(charger); + break; + case POWER_SUPPLY_PROP_CHARGE_TYPE: + val->intval = rt5033_get_charger_type(charger); + break; + case POWER_SUPPLY_PROP_CURRENT_MAX: + val->intval = rt5033_get_charger_current_limit(charger); + break; + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE: + val->intval = rt5033_get_charger_const_voltage(charger); + break; + case POWER_SUPPLY_PROP_MODEL_NAME: + val->strval = RT5033_CHARGER_MODEL; + break; + case POWER_SUPPLY_PROP_MANUFACTURER: + val->strval = RT5033_MANUFACTURER; + break; + case POWER_SUPPLY_PROP_ONLINE: + val->intval = (rt5033_get_charger_state(charger) == + POWER_SUPPLY_STATUS_CHARGING); + break; + default: + return -EINVAL; + } + + return 0; +} + +static struct rt5033_charger_data *rt5033_charger_dt_init( + struct rt5033_charger *charger) +{ + struct rt5033_charger_data *chg; + struct power_supply_battery_info *info; + int ret; + + chg = devm_kzalloc(charger->dev, sizeof(*chg), GFP_KERNEL); + if (!chg) + return ERR_PTR(-ENOMEM); + + ret = power_supply_get_battery_info(charger->psy, &info); + if (ret) + return ERR_PTR(dev_err_probe(charger->dev, -EINVAL, + "missing battery info\n")); + + /* Assign data. Validity will be checked in the init functions. */ + chg->pre_uamp = info->precharge_current_ua; + chg->fast_uamp = info->constant_charge_current_max_ua; + chg->eoc_uamp = info->charge_term_current_ua; + chg->pre_uvolt = info->precharge_voltage_max_uv; + chg->const_uvolt = info->constant_charge_voltage_max_uv; + + return chg; +} + +static const struct power_supply_desc rt5033_charger_desc = { + .name = "rt5033-charger", + .type = POWER_SUPPLY_TYPE_USB, + .properties = rt5033_charger_props, + .num_properties = ARRAY_SIZE(rt5033_charger_props), + .get_property = rt5033_charger_get_property, +}; + +static int rt5033_charger_probe(struct platform_device *pdev) +{ + struct rt5033_charger *charger; + struct power_supply_config psy_cfg = {}; + int ret; + + charger = devm_kzalloc(&pdev->dev, sizeof(*charger), GFP_KERNEL); + if (!charger) + return -ENOMEM; + + platform_set_drvdata(pdev, charger); + charger->dev = &pdev->dev; + charger->regmap = dev_get_regmap(pdev->dev.parent, NULL); + + psy_cfg.of_node = pdev->dev.of_node; + psy_cfg.drv_data = charger; + + charger->psy = devm_power_supply_register(&pdev->dev, + &rt5033_charger_desc, + &psy_cfg); + if (IS_ERR(charger->psy)) + return dev_err_probe(&pdev->dev, PTR_ERR(charger->psy), + "Failed to register power supply\n"); + + charger->chg = rt5033_charger_dt_init(charger); + if (IS_ERR_OR_NULL(charger->chg)) + return PTR_ERR(charger->chg); + + ret = rt5033_charger_reg_init(charger); + if (ret) + return ret; + + return 0; +} + +static const struct platform_device_id rt5033_charger_id[] = { + { "rt5033-charger", }, + { } +}; +MODULE_DEVICE_TABLE(platform, rt5033_charger_id); + +static const struct of_device_id rt5033_charger_of_match[] = { + { .compatible = "richtek,rt5033-charger", }, + { } +}; +MODULE_DEVICE_TABLE(of, rt5033_charger_of_match); + +static struct platform_driver rt5033_charger_driver = { + .driver = { + .name = "rt5033-charger", + .of_match_table = rt5033_charger_of_match, + }, + .probe = rt5033_charger_probe, + .id_table = rt5033_charger_id, +}; +module_platform_driver(rt5033_charger_driver); + +MODULE_DESCRIPTION("Richtek RT5033 charger driver"); +MODULE_AUTHOR("Beomho Seo <beomho.seo@samsung.com>"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/power/supply/rt9455_charger.c b/drivers/power/supply/rt9455_charger.c index 0149e00f2bf8..ff4dcf77c788 100644 --- a/drivers/power/supply/rt9455_charger.c +++ b/drivers/power/supply/rt9455_charger.c @@ -1737,7 +1737,7 @@ MODULE_DEVICE_TABLE(acpi, rt9455_i2c_acpi_match); #endif static struct i2c_driver rt9455_driver = { - .probe_new = rt9455_probe, + .probe = rt9455_probe, .remove = rt9455_remove, .id_table = rt9455_i2c_id_table, .driver = { diff --git a/drivers/power/supply/rt9467-charger.c b/drivers/power/supply/rt9467-charger.c index ea33693b6977..683adb18253d 100644 --- a/drivers/power/supply/rt9467-charger.c +++ b/drivers/power/supply/rt9467-charger.c @@ -1192,7 +1192,7 @@ static int rt9467_charger_probe(struct i2c_client *i2c) i2c_set_clientdata(i2c, data); /* Default pull charge enable gpio to make 'CHG_EN' by SW control only */ - ceb_gpio = devm_gpiod_get_optional(dev, "charge-enable", GPIOD_OUT_LOW); + ceb_gpio = devm_gpiod_get_optional(dev, "charge-enable", GPIOD_OUT_HIGH); if (IS_ERR(ceb_gpio)) return dev_err_probe(dev, PTR_ERR(ceb_gpio), "Failed to config charge enable gpio\n"); @@ -1272,7 +1272,7 @@ static struct i2c_driver rt9467_charger_driver = { .name = "rt9467-charger", .of_match_table = rt9467_charger_of_match_table, }, - .probe_new = rt9467_charger_probe, + .probe = rt9467_charger_probe, }; module_i2c_driver(rt9467_charger_driver); diff --git a/drivers/power/supply/rt9471.c b/drivers/power/supply/rt9471.c index 1ea40876494b..868b0703d15c 100644 --- a/drivers/power/supply/rt9471.c +++ b/drivers/power/supply/rt9471.c @@ -919,7 +919,7 @@ static struct i2c_driver rt9471_driver = { .name = "rt9471", .of_match_table = rt9471_of_device_id, }, - .probe_new = rt9471_probe, + .probe = rt9471_probe, .shutdown = rt9471_shutdown, }; module_i2c_driver(rt9471_driver); diff --git a/drivers/power/supply/sbs-battery.c b/drivers/power/supply/sbs-battery.c index c4a95b01463a..62a354e01204 100644 --- a/drivers/power/supply/sbs-battery.c +++ b/drivers/power/supply/sbs-battery.c @@ -1275,7 +1275,7 @@ static const struct of_device_id sbs_dt_ids[] = { MODULE_DEVICE_TABLE(of, sbs_dt_ids); static struct i2c_driver sbs_battery_driver = { - .probe_new = sbs_probe, + .probe = sbs_probe, .alert = sbs_alert, .id_table = sbs_id, .driver = { diff --git a/drivers/power/supply/sbs-charger.c b/drivers/power/supply/sbs-charger.c index a14e89ac0369..f4adde449270 100644 --- a/drivers/power/supply/sbs-charger.c +++ b/drivers/power/supply/sbs-charger.c @@ -240,7 +240,7 @@ static const struct i2c_device_id sbs_id[] = { MODULE_DEVICE_TABLE(i2c, sbs_id); static struct i2c_driver sbs_driver = { - .probe_new = sbs_probe, + .probe = sbs_probe, .id_table = sbs_id, .driver = { .name = "sbs-charger", diff --git a/drivers/power/supply/sbs-manager.c b/drivers/power/supply/sbs-manager.c index bde977391fd4..9e4141cffbf9 100644 --- a/drivers/power/supply/sbs-manager.c +++ b/drivers/power/supply/sbs-manager.c @@ -409,7 +409,7 @@ static struct i2c_driver sbsm_driver = { .name = "sbsm", .of_match_table = of_match_ptr(sbsm_dt_ids), }, - .probe_new = sbsm_probe, + .probe = sbsm_probe, .alert = sbsm_alert, .id_table = sbsm_ids }; diff --git a/drivers/power/supply/smb347-charger.c b/drivers/power/supply/smb347-charger.c index b5f038310282..c8392933ee28 100644 --- a/drivers/power/supply/smb347-charger.c +++ b/drivers/power/supply/smb347-charger.c @@ -1629,7 +1629,7 @@ static struct i2c_driver smb347_driver = { .name = "smb347", .of_match_table = smb3xx_of_match, }, - .probe_new = smb347_probe, + .probe = smb347_probe, .remove = smb347_remove, .shutdown = smb347_shutdown, .id_table = smb347_id, diff --git a/drivers/power/supply/twl4030_madc_battery.c b/drivers/power/supply/twl4030_madc_battery.c index 48649dcfe3a9..7fe029673b22 100644 --- a/drivers/power/supply/twl4030_madc_battery.c +++ b/drivers/power/supply/twl4030_madc_battery.c @@ -168,19 +168,13 @@ static int twl4030_madc_bat_get_property(struct power_supply *psy, return 0; } -static void twl4030_madc_bat_ext_changed(struct power_supply *psy) -{ - power_supply_changed(psy); -} - static const struct power_supply_desc twl4030_madc_bat_desc = { .name = "twl4030_battery", .type = POWER_SUPPLY_TYPE_BATTERY, .properties = twl4030_madc_bat_props, .num_properties = ARRAY_SIZE(twl4030_madc_bat_props), .get_property = twl4030_madc_bat_get_property, - .external_power_changed = twl4030_madc_bat_ext_changed, - + .external_power_changed = power_supply_changed, }; static int twl4030_cmp(const void *a, const void *b) diff --git a/drivers/power/supply/ucs1002_power.c b/drivers/power/supply/ucs1002_power.c index 836d44c9fb74..954feba6600b 100644 --- a/drivers/power/supply/ucs1002_power.c +++ b/drivers/power/supply/ucs1002_power.c @@ -680,7 +680,7 @@ static struct i2c_driver ucs1002_driver = { .name = "ucs1002", .of_match_table = ucs1002_of_match, }, - .probe_new = ucs1002_probe, + .probe = ucs1002_probe, }; module_i2c_driver(ucs1002_driver); diff --git a/drivers/power/supply/ug3105_battery.c b/drivers/power/supply/ug3105_battery.c index fbc966842509..ccc5c4d2e230 100644 --- a/drivers/power/supply/ug3105_battery.c +++ b/drivers/power/supply/ug3105_battery.c @@ -476,7 +476,7 @@ static struct i2c_driver ug3105_i2c_driver = { .name = "ug3105", .pm = &ug3105_pm_ops, }, - .probe_new = ug3105_probe, + .probe = ug3105_probe, .id_table = ug3105_id, }; module_i2c_driver(ug3105_i2c_driver); |