1 files changed, 0 insertions, 116 deletions
diff --git a/drivers/scsi/ufs/ufs_quirks.h b/drivers/scsi/ufs/ufs_quirks.h
deleted file mode 100644
index bcb4f004bed5..000000000000
--- a/drivers/scsi/ufs/ufs_quirks.h
+++ /dev/null
@@ -1,116 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
- */
-
-#ifndef _UFS_QUIRKS_H_
-#define _UFS_QUIRKS_H_
-
-/* return true if s1 is a prefix of s2 */
-#define STR_PRFX_EQUAL(s1, s2) !strncmp(s1, s2, strlen(s1))
-
-#define UFS_ANY_VENDOR 0xFFFF
-#define UFS_ANY_MODEL  "ANY_MODEL"
-
-#define UFS_VENDOR_MICRON      0x12C
-#define UFS_VENDOR_SAMSUNG     0x1CE
-#define UFS_VENDOR_SKHYNIX     0x1AD
-#define UFS_VENDOR_TOSHIBA     0x198
-#define UFS_VENDOR_WDC         0x145
-
-/**
- * ufs_dev_quirk - ufs device quirk info
- * @card: ufs card details
- * @quirk: device quirk
- */
-struct ufs_dev_quirk {
-	u16 wmanufacturerid;
-	const u8 *model;
-	unsigned int quirk;
-};
-
-/*
- * Some vendor's UFS device sends back to back NACs for the DL data frames
- * causing the host controller to raise the DFES error status. Sometimes
- * such UFS devices send back to back NAC without waiting for new
- * retransmitted DL frame from the host and in such cases it might be possible
- * the Host UniPro goes into bad state without raising the DFES error
- * interrupt. If this happens then all the pending commands would timeout
- * only after respective SW command (which is generally too large).
- *
- * We can workaround such device behaviour like this:
- * - As soon as SW sees the DL NAC error, it should schedule the error handler
- * - Error handler would sleep for 50ms to see if there are any fatal errors
- *   raised by UFS controller.
- *    - If there are fatal errors then SW does normal error recovery.
- *    - If there are no fatal errors then SW sends the NOP command to device
- *      to check if link is alive.
- *        - If NOP command times out, SW does normal error recovery
- *        - If NOP command succeed, skip the error handling.
- *
- * If DL NAC error is seen multiple times with some vendor's UFS devices then
- * enable this quirk to initiate quick error recovery and also silence related
- * error logs to reduce spamming of kernel logs.
- */
-#define UFS_DEVICE_QUIRK_RECOVERY_FROM_DL_NAC_ERRORS (1 << 2)
-
-/*
- * Few Toshiba UFS device models advertise RX_MIN_ACTIVATETIME_CAPABILITY as
- * 600us which may not be enough for reliable hibern8 exit hardware sequence
- * from UFS device.
- * To workaround this issue, host should set its PA_TACTIVATE time to 1ms even
- * if device advertises RX_MIN_ACTIVATETIME_CAPABILITY less than 1ms.
- */
-#define UFS_DEVICE_QUIRK_PA_TACTIVATE	(1 << 4)
-
-/*
- * It seems some UFS devices may keep drawing more than sleep current
- * (atleast for 500us) from UFS rails (especially from VCCQ rail).
- * To avoid this situation, add 2ms delay before putting these UFS
- * rails in LPM mode.
- */
-#define UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM	(1 << 6)
-
-/*
- * Some UFS devices require host PA_TACTIVATE to be lower than device
- * PA_TACTIVATE, enabling this quirk ensure this.
- */
-#define UFS_DEVICE_QUIRK_HOST_PA_TACTIVATE	(1 << 7)
-
-/*
- * The max. value PA_SaveConfigTime is 250 (10us) but this is not enough for
- * some vendors.
- * Gear switch from PWM to HS may fail even with this max. PA_SaveConfigTime.
- * Gear switch can be issued by host controller as an error recovery and any
- * software delay will not help on this case so we need to increase
- * PA_SaveConfigTime to >32us as per vendor recommendation.
- */
-#define UFS_DEVICE_QUIRK_HOST_PA_SAVECONFIGTIME	(1 << 8)
-
-/*
- * Some UFS devices require VS_DebugSaveConfigTime is 0x10,
- * enabling this quirk ensure this.
- */
-#define UFS_DEVICE_QUIRK_HOST_VS_DEBUGSAVECONFIGTIME	(1 << 9)
-
-/*
- * Some pre-3.1 UFS devices can support extended features by upgrading
- * the firmware. Enable this quirk to make UFS core driver probe and enable
- * supported features on such devices.
- */
-#define UFS_DEVICE_QUIRK_SUPPORT_EXTENDED_FEATURES (1 << 10)
-
-/*
- * Some UFS devices require delay after VCC power rail is turned-off.
- * Enable this quirk to introduce 5ms delays after VCC power-off during
- * suspend flow.
- */
-#define UFS_DEVICE_QUIRK_DELAY_AFTER_LPM        (1 << 11)
-
-/*
- * Some UFS devices require L2P entry should be swapped before being sent to the
- * UFS device for HPB READ command.
- */
-#define UFS_DEVICE_QUIRK_SWAP_L2P_ENTRY_FOR_HPB_READ (1 << 12)
-
-#endif /* UFS_QUIRKS_H_ */