diff options
Diffstat (limited to 'drivers/thermal')
| -rw-r--r-- | drivers/thermal/intel/intel_pch_thermal.c | 76 |
1 files changed, 70 insertions, 6 deletions
diff --git a/drivers/thermal/intel/intel_pch_thermal.c b/drivers/thermal/intel/intel_pch_thermal.c index 3b813ebb6ca1..0a9e4458bc3a 100644 --- a/drivers/thermal/intel/intel_pch_thermal.c +++ b/drivers/thermal/intel/intel_pch_thermal.c @@ -7,14 +7,16 @@ * Tushar Dave <tushar.n.dave@intel.com> */ +#include <linux/acpi.h> +#include <linux/delay.h> #include <linux/module.h> -#include <linux/types.h> #include <linux/init.h> #include <linux/pci.h> -#include <linux/acpi.h> +#include <linux/pm.h> +#include <linux/suspend.h> #include <linux/thermal.h> +#include <linux/types.h> #include <linux/units.h> -#include <linux/pm.h> /* Intel PCH thermal Device IDs */ #define PCH_THERMAL_DID_HSW_1 0x9C24 /* Haswell PCH */ @@ -35,6 +37,7 @@ #define WPT_TSREL 0x0A /* Thermal Sensor Report Enable and Lock */ #define WPT_TSMIC 0x0C /* Thermal Sensor SMI Control */ #define WPT_CTT 0x0010 /* Catastrophic Trip Point */ +#define WPT_TSPM 0x001C /* Thermal Sensor Power Management */ #define WPT_TAHV 0x0014 /* Thermal Alert High Value */ #define WPT_TALV 0x0018 /* Thermal Alert Low Value */ #define WPT_TL 0x00000040 /* Throttle Value */ @@ -55,6 +58,22 @@ #define WPT_TL_T1L 0x1ff00000 /* T1 Level */ #define WPT_TL_TTEN 0x20000000 /* TT Enable */ +/* Resolution of 1/2 degree C and an offset of -50C */ +#define PCH_TEMP_OFFSET (-50) +#define GET_WPT_TEMP(x) ((x) * MILLIDEGREE_PER_DEGREE / 2 + WPT_TEMP_OFFSET) +#define WPT_TEMP_OFFSET (PCH_TEMP_OFFSET * MILLIDEGREE_PER_DEGREE) +#define GET_PCH_TEMP(x) (((x) / 2) + PCH_TEMP_OFFSET) + +/* Amount of time for each cooling delay, 100ms by default for now */ +static unsigned int delay_timeout = 100; +module_param(delay_timeout, int, 0644); +MODULE_PARM_DESC(delay_timeout, "amount of time delay for each iteration."); + +/* Number of iterations for cooling delay, 10 counts by default for now */ +static unsigned int delay_cnt = 10; +module_param(delay_cnt, int, 0644); +MODULE_PARM_DESC(delay_cnt, "total number of iterations for time delay."); + static char driver_name[] = "Intel PCH thermal driver"; struct pch_thermal_device { @@ -183,13 +202,58 @@ static int pch_wpt_get_temp(struct pch_thermal_device *ptd, int *temp) static int pch_wpt_suspend(struct pch_thermal_device *ptd) { u8 tsel; + u8 pch_delay_cnt = 1; + u16 pch_thr_temp, pch_cur_temp; - if (ptd->bios_enabled) + /* Shutdown the thermal sensor if it is not enabled by BIOS */ + if (!ptd->bios_enabled) { + tsel = readb(ptd->hw_base + WPT_TSEL); + writeb(tsel & 0xFE, ptd->hw_base + WPT_TSEL); + return 0; + } + + /* Do not check temperature if it is not a S0ix capable platform */ + if (!(acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0)) return 0; - tsel = readb(ptd->hw_base + WPT_TSEL); + /* Do not check temperature if it is not s2idle */ + if (pm_suspend_via_firmware()) + return 0; + + /* Get the PCH temperature threshold value */ + pch_thr_temp = GET_PCH_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TSPM)); + + /* Get the PCH current temperature value */ + pch_cur_temp = GET_PCH_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TEMP)); - writeb(tsel & 0xFE, ptd->hw_base + WPT_TSEL); + /* + * If current PCH temperature is higher than configured PCH threshold + * value, run some delay loop with sleep to let the current temperature + * go down below the threshold value which helps to allow system enter + * lower power S0ix suspend state. Even after delay loop if PCH current + * temperature stays above threshold, notify the warning message + * which helps to indentify the reason why S0ix entry was rejected. + */ + while (pch_delay_cnt <= delay_cnt) { + if (pch_cur_temp <= pch_thr_temp) + break; + + dev_warn(&ptd->pdev->dev, + "CPU-PCH current temp [%dC] higher than the threshold temp [%dC], sleep %d times for %d ms duration\n", + pch_cur_temp, pch_thr_temp, pch_delay_cnt, delay_timeout); + msleep(delay_timeout); + /* Read the PCH current temperature for next cycle. */ + pch_cur_temp = GET_PCH_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TEMP)); + pch_delay_cnt++; + } + + if (pch_cur_temp > pch_thr_temp) + dev_warn(&ptd->pdev->dev, + "CPU-PCH is hot [%dC] even after delay, continue to suspend. S0ix might fail\n", + pch_cur_temp); + else + dev_info(&ptd->pdev->dev, + "CPU-PCH is cool [%dC], continue to suspend\n", pch_cur_temp); return 0; } |