diff options
Diffstat (limited to 'drivers/tty/serial')
-rw-r--r-- | drivers/tty/serial/8250/8250_dw.c | 6 | ||||
-rw-r--r-- | drivers/tty/serial/amba-pl011.c | 60 | ||||
-rw-r--r-- | drivers/tty/serial/fsl_lpuart.c | 7 | ||||
-rw-r--r-- | drivers/tty/serial/imx.c | 22 | ||||
-rw-r--r-- | drivers/tty/serial/qcom_geni_serial.c | 10 | ||||
-rw-r--r-- | drivers/tty/serial/serial_port.c | 25 | ||||
-rw-r--r-- | drivers/tty/serial/stm32-usart.c | 4 |
7 files changed, 89 insertions, 45 deletions
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c index 2d1f350a4bea..c1d43f040c43 100644 --- a/drivers/tty/serial/8250/8250_dw.c +++ b/drivers/tty/serial/8250/8250_dw.c @@ -357,9 +357,9 @@ static void dw8250_set_termios(struct uart_port *p, struct ktermios *termios, long rate; int ret; - clk_disable_unprepare(d->clk); rate = clk_round_rate(d->clk, newrate); - if (rate > 0) { + if (rate > 0 && p->uartclk != rate) { + clk_disable_unprepare(d->clk); /* * Note that any clock-notifer worker will block in * serial8250_update_uartclk() until we are done. @@ -367,8 +367,8 @@ static void dw8250_set_termios(struct uart_port *p, struct ktermios *termios, ret = clk_set_rate(d->clk, newrate); if (!ret) p->uartclk = rate; + clk_prepare_enable(d->clk); } - clk_prepare_enable(d->clk); dw8250_do_set_termios(p, termios, old); } diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index fccec1698a54..cf2c890a560f 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -1339,11 +1339,41 @@ static void pl011_start_tx_pio(struct uart_amba_port *uap) } } +static void pl011_rs485_tx_start(struct uart_amba_port *uap) +{ + struct uart_port *port = &uap->port; + u32 cr; + + /* Enable transmitter */ + cr = pl011_read(uap, REG_CR); + cr |= UART011_CR_TXE; + + /* Disable receiver if half-duplex */ + if (!(port->rs485.flags & SER_RS485_RX_DURING_TX)) + cr &= ~UART011_CR_RXE; + + if (port->rs485.flags & SER_RS485_RTS_ON_SEND) + cr &= ~UART011_CR_RTS; + else + cr |= UART011_CR_RTS; + + pl011_write(cr, uap, REG_CR); + + if (port->rs485.delay_rts_before_send) + mdelay(port->rs485.delay_rts_before_send); + + uap->rs485_tx_started = true; +} + static void pl011_start_tx(struct uart_port *port) { struct uart_amba_port *uap = container_of(port, struct uart_amba_port, port); + if ((uap->port.rs485.flags & SER_RS485_ENABLED) && + !uap->rs485_tx_started) + pl011_rs485_tx_start(uap); + if (!pl011_dma_tx_start(uap)) pl011_start_tx_pio(uap); } @@ -1424,42 +1454,12 @@ static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c, return true; } -static void pl011_rs485_tx_start(struct uart_amba_port *uap) -{ - struct uart_port *port = &uap->port; - u32 cr; - - /* Enable transmitter */ - cr = pl011_read(uap, REG_CR); - cr |= UART011_CR_TXE; - - /* Disable receiver if half-duplex */ - if (!(port->rs485.flags & SER_RS485_RX_DURING_TX)) - cr &= ~UART011_CR_RXE; - - if (port->rs485.flags & SER_RS485_RTS_ON_SEND) - cr &= ~UART011_CR_RTS; - else - cr |= UART011_CR_RTS; - - pl011_write(cr, uap, REG_CR); - - if (port->rs485.delay_rts_before_send) - mdelay(port->rs485.delay_rts_before_send); - - uap->rs485_tx_started = true; -} - /* Returns true if tx interrupts have to be (kept) enabled */ static bool pl011_tx_chars(struct uart_amba_port *uap, bool from_irq) { struct circ_buf *xmit = &uap->port.state->xmit; int count = uap->fifosize >> 1; - if ((uap->port.rs485.flags & SER_RS485_ENABLED) && - !uap->rs485_tx_started) - pl011_rs485_tx_start(uap); - if (uap->port.x_char) { if (!pl011_tx_char(uap, uap->port.x_char, from_irq)) return true; diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c index 5ddf110aedbe..bbcbc91482af 100644 --- a/drivers/tty/serial/fsl_lpuart.c +++ b/drivers/tty/serial/fsl_lpuart.c @@ -2345,9 +2345,12 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios, lpuart32_write(&sport->port, bd, UARTBAUD); lpuart32_serial_setbrg(sport, baud); - lpuart32_write(&sport->port, modem, UARTMODIR); - lpuart32_write(&sport->port, ctrl, UARTCTRL); + /* disable CTS before enabling UARTCTRL_TE to avoid pending idle preamble */ + lpuart32_write(&sport->port, modem & ~UARTMODIR_TXCTSE, UARTMODIR); /* restore control register */ + lpuart32_write(&sport->port, ctrl, UARTCTRL); + /* re-enable the CTS if needed */ + lpuart32_write(&sport->port, modem, UARTMODIR); if ((ctrl & (UARTCTRL_PE | UARTCTRL_M)) == UARTCTRL_PE) sport->is_cs7 = true; diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index 4aa72d5aeafb..e14813250616 100644 --- a/drivers/tty/serial/imx.c +++ b/drivers/tty/serial/imx.c @@ -462,8 +462,7 @@ static void imx_uart_stop_tx(struct uart_port *port) } } -/* called with port.lock taken and irqs off */ -static void imx_uart_stop_rx(struct uart_port *port) +static void imx_uart_stop_rx_with_loopback_ctrl(struct uart_port *port, bool loopback) { struct imx_port *sport = (struct imx_port *)port; u32 ucr1, ucr2, ucr4, uts; @@ -485,7 +484,7 @@ static void imx_uart_stop_rx(struct uart_port *port) /* See SER_RS485_ENABLED/UTS_LOOP comment in imx_uart_probe() */ if (port->rs485.flags & SER_RS485_ENABLED && port->rs485.flags & SER_RS485_RTS_ON_SEND && - sport->have_rtscts && !sport->have_rtsgpio) { + sport->have_rtscts && !sport->have_rtsgpio && loopback) { uts = imx_uart_readl(sport, imx_uart_uts_reg(sport)); uts |= UTS_LOOP; imx_uart_writel(sport, uts, imx_uart_uts_reg(sport)); @@ -498,6 +497,16 @@ static void imx_uart_stop_rx(struct uart_port *port) } /* called with port.lock taken and irqs off */ +static void imx_uart_stop_rx(struct uart_port *port) +{ + /* + * Stop RX and enable loopback in order to make sure RS485 bus + * is not blocked. Se comment in imx_uart_probe(). + */ + imx_uart_stop_rx_with_loopback_ctrl(port, true); +} + +/* called with port.lock taken and irqs off */ static void imx_uart_enable_ms(struct uart_port *port) { struct imx_port *sport = (struct imx_port *)port; @@ -682,9 +691,14 @@ static void imx_uart_start_tx(struct uart_port *port) imx_uart_rts_inactive(sport, &ucr2); imx_uart_writel(sport, ucr2, UCR2); + /* + * Since we are about to transmit we can not stop RX + * with loopback enabled because that will make our + * transmitted data being just looped to RX. + */ if (!(port->rs485.flags & SER_RS485_RX_DURING_TX) && !port->rs485_rx_during_tx_gpio) - imx_uart_stop_rx(port); + imx_uart_stop_rx_with_loopback_ctrl(port, false); sport->tx_state = WAIT_AFTER_RTS; diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c index e63a8fbe63bd..99e08737f293 100644 --- a/drivers/tty/serial/qcom_geni_serial.c +++ b/drivers/tty/serial/qcom_geni_serial.c @@ -851,19 +851,21 @@ static void qcom_geni_serial_stop_tx(struct uart_port *uport) } static void qcom_geni_serial_send_chunk_fifo(struct uart_port *uport, - unsigned int remaining) + unsigned int chunk) { struct qcom_geni_serial_port *port = to_dev_port(uport); struct circ_buf *xmit = &uport->state->xmit; - unsigned int tx_bytes; + unsigned int tx_bytes, c, remaining = chunk; u8 buf[BYTES_PER_FIFO_WORD]; while (remaining) { memset(buf, 0, sizeof(buf)); tx_bytes = min(remaining, BYTES_PER_FIFO_WORD); - memcpy(buf, &xmit->buf[xmit->tail], tx_bytes); - uart_xmit_advance(uport, tx_bytes); + for (c = 0; c < tx_bytes ; c++) { + buf[c] = xmit->buf[xmit->tail]; + uart_xmit_advance(uport, 1); + } iowrite32_rep(uport->membase + SE_GENI_TX_FIFOn, buf, 1); diff --git a/drivers/tty/serial/serial_port.c b/drivers/tty/serial/serial_port.c index 88975a4df306..72b6f4f326e2 100644 --- a/drivers/tty/serial/serial_port.c +++ b/drivers/tty/serial/serial_port.c @@ -46,8 +46,31 @@ out: return 0; } +static int serial_port_runtime_suspend(struct device *dev) +{ + struct serial_port_device *port_dev = to_serial_base_port_device(dev); + struct uart_port *port = port_dev->port; + unsigned long flags; + bool busy; + + if (port->flags & UPF_DEAD) + return 0; + + uart_port_lock_irqsave(port, &flags); + busy = __serial_port_busy(port); + if (busy) + port->ops->start_tx(port); + uart_port_unlock_irqrestore(port, flags); + + if (busy) + pm_runtime_mark_last_busy(dev); + + return busy ? -EBUSY : 0; +} + static DEFINE_RUNTIME_DEV_PM_OPS(serial_port_pm, - NULL, serial_port_runtime_resume, NULL); + serial_port_runtime_suspend, + serial_port_runtime_resume, NULL); static int serial_port_probe(struct device *dev) { diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c index 794b77512740..693e932d6feb 100644 --- a/drivers/tty/serial/stm32-usart.c +++ b/drivers/tty/serial/stm32-usart.c @@ -251,7 +251,9 @@ static int stm32_usart_config_rs485(struct uart_port *port, struct ktermios *ter writel_relaxed(cr3, port->membase + ofs->cr3); writel_relaxed(cr1, port->membase + ofs->cr1); - rs485conf->flags |= SER_RS485_RX_DURING_TX; + if (!port->rs485_rx_during_tx_gpio) + rs485conf->flags |= SER_RS485_RX_DURING_TX; + } else { stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_DEM | USART_CR3_DEP); |