diff options
Diffstat (limited to 'include/drm/drm_connector.h')
| -rw-r--r-- | include/drm/drm_connector.h | 208 |
1 files changed, 154 insertions, 54 deletions
diff --git a/include/drm/drm_connector.h b/include/drm/drm_connector.h index 9ccad6b062f2..02a131202add 100644 --- a/include/drm/drm_connector.h +++ b/include/drm/drm_connector.h @@ -253,6 +253,96 @@ enum drm_panel_orientation { DRM_MODE_PANEL_ORIENTATION_RIGHT_UP, }; +/* + * This is a consolidated colorimetry list supported by HDMI and + * DP protocol standard. The respective connectors will register + * a property with the subset of this list (supported by that + * respective protocol). Userspace will set the colorspace through + * a colorspace property which will be created and exposed to + * userspace. + */ + +/* For Default case, driver will set the colorspace */ +#define DRM_MODE_COLORIMETRY_DEFAULT 0 +/* CEA 861 Normal Colorimetry options */ +#define DRM_MODE_COLORIMETRY_NO_DATA 0 +#define DRM_MODE_COLORIMETRY_SMPTE_170M_YCC 1 +#define DRM_MODE_COLORIMETRY_BT709_YCC 2 +/* CEA 861 Extended Colorimetry Options */ +#define DRM_MODE_COLORIMETRY_XVYCC_601 3 +#define DRM_MODE_COLORIMETRY_XVYCC_709 4 +#define DRM_MODE_COLORIMETRY_SYCC_601 5 +#define DRM_MODE_COLORIMETRY_OPYCC_601 6 +#define DRM_MODE_COLORIMETRY_OPRGB 7 +#define DRM_MODE_COLORIMETRY_BT2020_CYCC 8 +#define DRM_MODE_COLORIMETRY_BT2020_RGB 9 +#define DRM_MODE_COLORIMETRY_BT2020_YCC 10 +/* Additional Colorimetry extension added as part of CTA 861.G */ +#define DRM_MODE_COLORIMETRY_DCI_P3_RGB_D65 11 +#define DRM_MODE_COLORIMETRY_DCI_P3_RGB_THEATER 12 + +/** + * enum drm_bus_flags - bus_flags info for &drm_display_info + * + * This enum defines signal polarities and clock edge information for signals on + * a bus as bitmask flags. + * + * The clock edge information is conveyed by two sets of symbols, + * DRM_BUS_FLAGS_*_DRIVE_\* and DRM_BUS_FLAGS_*_SAMPLE_\*. When this enum is + * used to describe a bus from the point of view of the transmitter, the + * \*_DRIVE_\* flags should be used. When used from the point of view of the + * receiver, the \*_SAMPLE_\* flags should be used. The \*_DRIVE_\* and + * \*_SAMPLE_\* flags alias each other, with the \*_SAMPLE_POSEDGE and + * \*_SAMPLE_NEGEDGE flags being equal to \*_DRIVE_NEGEDGE and \*_DRIVE_POSEDGE + * respectively. This simplifies code as signals are usually sampled on the + * opposite edge of the driving edge. Transmitters and receivers may however + * need to take other signal timings into account to convert between driving + * and sample edges. + * + * @DRM_BUS_FLAG_DE_LOW: The Data Enable signal is active low + * @DRM_BUS_FLAG_DE_HIGH: The Data Enable signal is active high + * @DRM_BUS_FLAG_PIXDATA_POSEDGE: Legacy value, do not use + * @DRM_BUS_FLAG_PIXDATA_NEGEDGE: Legacy value, do not use + * @DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE: Data is driven on the rising edge of + * the pixel clock + * @DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE: Data is driven on the falling edge of + * the pixel clock + * @DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE: Data is sampled on the rising edge of + * the pixel clock + * @DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE: Data is sampled on the falling edge of + * the pixel clock + * @DRM_BUS_FLAG_DATA_MSB_TO_LSB: Data is transmitted MSB to LSB on the bus + * @DRM_BUS_FLAG_DATA_LSB_TO_MSB: Data is transmitted LSB to MSB on the bus + * @DRM_BUS_FLAG_SYNC_POSEDGE: Legacy value, do not use + * @DRM_BUS_FLAG_SYNC_NEGEDGE: Legacy value, do not use + * @DRM_BUS_FLAG_SYNC_DRIVE_POSEDGE: Sync signals are driven on the rising + * edge of the pixel clock + * @DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE: Sync signals are driven on the falling + * edge of the pixel clock + * @DRM_BUS_FLAG_SYNC_SAMPLE_POSEDGE: Sync signals are sampled on the rising + * edge of the pixel clock + * @DRM_BUS_FLAG_SYNC_SAMPLE_NEGEDGE: Sync signals are sampled on the falling + * edge of the pixel clock + */ +enum drm_bus_flags { + DRM_BUS_FLAG_DE_LOW = BIT(0), + DRM_BUS_FLAG_DE_HIGH = BIT(1), + DRM_BUS_FLAG_PIXDATA_POSEDGE = BIT(2), + DRM_BUS_FLAG_PIXDATA_NEGEDGE = BIT(3), + DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE = DRM_BUS_FLAG_PIXDATA_POSEDGE, + DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE = DRM_BUS_FLAG_PIXDATA_NEGEDGE, + DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE = DRM_BUS_FLAG_PIXDATA_NEGEDGE, + DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE = DRM_BUS_FLAG_PIXDATA_POSEDGE, + DRM_BUS_FLAG_DATA_MSB_TO_LSB = BIT(4), + DRM_BUS_FLAG_DATA_LSB_TO_MSB = BIT(5), + DRM_BUS_FLAG_SYNC_POSEDGE = BIT(6), + DRM_BUS_FLAG_SYNC_NEGEDGE = BIT(7), + DRM_BUS_FLAG_SYNC_DRIVE_POSEDGE = DRM_BUS_FLAG_SYNC_POSEDGE, + DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE = DRM_BUS_FLAG_SYNC_NEGEDGE, + DRM_BUS_FLAG_SYNC_SAMPLE_POSEDGE = DRM_BUS_FLAG_SYNC_NEGEDGE, + DRM_BUS_FLAG_SYNC_SAMPLE_NEGEDGE = DRM_BUS_FLAG_SYNC_POSEDGE, +}; + /** * struct drm_display_info - runtime data about the connected sink * @@ -266,26 +356,16 @@ enum drm_panel_orientation { */ struct drm_display_info { /** - * @name: Name of the display. - */ - char name[DRM_DISPLAY_INFO_LEN]; - - /** * @width_mm: Physical width in mm. */ - unsigned int width_mm; + unsigned int width_mm; + /** * @height_mm: Physical height in mm. */ unsigned int height_mm; /** - * @pixel_clock: Maximum pixel clock supported by the sink, in units of - * 100Hz. This mismatches the clock in &drm_display_mode (which is in - * kHZ), because that's what the EDID uses as base unit. - */ - unsigned int pixel_clock; - /** * @bpc: Maximum bits per color channel. Used by HDMI and DP outputs. */ unsigned int bpc; @@ -328,24 +408,10 @@ struct drm_display_info { */ unsigned int num_bus_formats; -#define DRM_BUS_FLAG_DE_LOW (1<<0) -#define DRM_BUS_FLAG_DE_HIGH (1<<1) -/* drive data on pos. edge */ -#define DRM_BUS_FLAG_PIXDATA_POSEDGE (1<<2) -/* drive data on neg. edge */ -#define DRM_BUS_FLAG_PIXDATA_NEGEDGE (1<<3) -/* data is transmitted MSB to LSB on the bus */ -#define DRM_BUS_FLAG_DATA_MSB_TO_LSB (1<<4) -/* data is transmitted LSB to MSB on the bus */ -#define DRM_BUS_FLAG_DATA_LSB_TO_MSB (1<<5) -/* drive sync on pos. edge */ -#define DRM_BUS_FLAG_SYNC_POSEDGE (1<<6) -/* drive sync on neg. edge */ -#define DRM_BUS_FLAG_SYNC_NEGEDGE (1<<7) - /** * @bus_flags: Additional information (like pixel signal polarity) for - * the pixel data on the bus, using DRM_BUS_FLAGS\_ defines. + * the pixel data on the bus, using &enum drm_bus_flags values + * DRM_BUS_FLAGS\_. */ u32 bus_flags; @@ -366,6 +432,12 @@ struct drm_display_info { bool has_hdmi_infoframe; /** + * @rgb_quant_range_selectable: Does the sink support selecting + * the RGB quantization range? + */ + bool rgb_quant_range_selectable; + + /** * @edid_hdmi_dc_modes: Mask of supported hdmi deep color modes. Even * more stuff redundant with @bus_formats. */ @@ -394,7 +466,7 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info, /** * struct drm_tv_connector_state - TV connector related states * @subconnector: selected subconnector - * @margins: margins + * @margins: margins (all margins are expressed in pixels) * @margins.left: left margin * @margins.right: right margin * @margins.top: top margin @@ -497,6 +569,13 @@ struct drm_connector_state { unsigned int content_protection; /** + * @colorspace: State variable for Connector property to request + * colorspace change on Sink. This is most commonly used to switch + * to wider color gamuts like BT2020. + */ + u32 colorspace; + + /** * @writeback_job: Writeback job for writeback connectors * * Holds the framebuffer and out-fence for a writeback connector. As @@ -508,6 +587,18 @@ struct drm_connector_state { * drm_writeback_signal_completion() */ struct drm_writeback_job *writeback_job; + + /** + * @max_requested_bpc: Connector property to limit the maximum bit + * depth of the pixels. + */ + u8 max_requested_bpc; + + /** + * @max_bpc: Connector max_bpc based on the requested max_bpc property + * and the connector bpc limitations obtained from edid. + */ + u8 max_bpc; }; /** @@ -894,7 +985,7 @@ struct drm_connector { /** * @ycbcr_420_allowed : This bool indicates if this connector is * capable of handling YCBCR 420 output. While parsing the EDID - * blocks, its very helpful to know, if the source is capable of + * blocks it's very helpful to know if the source is capable of * handling YCBCR 420 outputs. */ bool ycbcr_420_allowed; @@ -960,12 +1051,29 @@ struct drm_connector { struct drm_property *scaling_mode_property; /** + * @vrr_capable_property: Optional property to help userspace + * query hardware support for variable refresh rate on a connector. + * connector. Drivers can add the property to a connector by + * calling drm_connector_attach_vrr_capable_property(). + * + * This should be updated only by calling + * drm_connector_set_vrr_capable_property(). + */ + struct drm_property *vrr_capable_property; + + /** * @content_protection_property: DRM ENUM property for content * protection. See drm_connector_attach_content_protection_property(). */ struct drm_property *content_protection_property; /** + * @colorspace_property: Connector property to set the suitable + * colorspace supported by the sink. + */ + struct drm_property *colorspace_property; + + /** * @path_blob_ptr: * * DRM blob property data for the DP MST path property. This should only @@ -973,6 +1081,12 @@ struct drm_connector { */ struct drm_property_blob *path_blob_ptr; + /** + * @max_bpc_property: Default connector property for the max bpc to be + * driven out of the connector. + */ + struct drm_property *max_bpc_property; + #define DRM_CONNECTOR_POLL_HPD (1 << 0) #define DRM_CONNECTOR_POLL_CONNECT (1 << 1) #define DRM_CONNECTOR_POLL_DISCONNECT (1 << 2) @@ -1133,6 +1247,7 @@ int drm_connector_init(struct drm_device *dev, struct drm_connector *connector, const struct drm_connector_funcs *funcs, int connector_type); +void drm_connector_attach_edid_property(struct drm_connector *connector); int drm_connector_register(struct drm_connector *connector); void drm_connector_unregister(struct drm_connector *connector); int drm_connector_attach_encoder(struct drm_connector *connector, @@ -1192,30 +1307,6 @@ static inline void drm_connector_put(struct drm_connector *connector) } /** - * drm_connector_reference - acquire a connector reference - * @connector: DRM connector - * - * This is a compatibility alias for drm_connector_get() and should not be - * used by new code. - */ -static inline void drm_connector_reference(struct drm_connector *connector) -{ - drm_connector_get(connector); -} - -/** - * drm_connector_unreference - release a connector reference - * @connector: DRM connector - * - * This is a compatibility alias for drm_connector_put() and should not be - * used by new code. - */ -static inline void drm_connector_unreference(struct drm_connector *connector) -{ - drm_connector_put(connector); -} - -/** * drm_connector_is_unregistered - has the connector been unregistered from * userspace? * @connector: DRM connector @@ -1243,16 +1334,21 @@ const char *drm_get_tv_select_name(int val); const char *drm_get_content_protection_name(int val); int drm_mode_create_dvi_i_properties(struct drm_device *dev); +int drm_mode_create_tv_margin_properties(struct drm_device *dev); int drm_mode_create_tv_properties(struct drm_device *dev, unsigned int num_modes, const char * const modes[]); +void drm_connector_attach_tv_margin_properties(struct drm_connector *conn); int drm_mode_create_scaling_mode_property(struct drm_device *dev); int drm_connector_attach_content_type_property(struct drm_connector *dev); int drm_connector_attach_scaling_mode_property(struct drm_connector *connector, u32 scaling_mode_mask); +int drm_connector_attach_vrr_capable_property( + struct drm_connector *connector); int drm_connector_attach_content_protection_property( struct drm_connector *connector); int drm_mode_create_aspect_ratio_property(struct drm_device *dev); +int drm_mode_create_colorspace_property(struct drm_connector *connector); int drm_mode_create_content_type_property(struct drm_device *dev); void drm_hdmi_avi_infoframe_content_type(struct hdmi_avi_infoframe *frame, const struct drm_connector_state *conn_state); @@ -1266,8 +1362,12 @@ int drm_connector_update_edid_property(struct drm_connector *connector, const struct edid *edid); void drm_connector_set_link_status_property(struct drm_connector *connector, uint64_t link_status); +void drm_connector_set_vrr_capable_property( + struct drm_connector *connector, bool capable); int drm_connector_init_panel_orientation_property( struct drm_connector *connector, int width, int height); +int drm_connector_attach_max_bpc_property(struct drm_connector *connector, + int min, int max); /** * struct drm_tile_group - Tile group metadata |