diff options
Diffstat (limited to 'include/linux/spi/spi.h')
| -rw-r--r-- | include/linux/spi/spi.h | 44 |
1 files changed, 22 insertions, 22 deletions
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index aa09fdc8042d..592897fa4f03 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -6,6 +6,7 @@ #ifndef __LINUX_SPI_H #define __LINUX_SPI_H +#include <linux/bits.h> #include <linux/device.h> #include <linux/mod_devicetable.h> #include <linux/slab.h> @@ -15,6 +16,8 @@ #include <linux/gpio/consumer.h> #include <linux/ptp_clock_kernel.h> +#include <uapi/linux/spi/spi.h> + struct dma_chan; struct property_entry; struct spi_controller; @@ -164,28 +167,19 @@ struct spi_device { u8 chip_select; u8 bits_per_word; bool rt; +#define SPI_NO_TX BIT(31) /* no transmit wire */ +#define SPI_NO_RX BIT(30) /* no receive wire */ + /* + * All bits defined above should be covered by SPI_MODE_KERNEL_MASK. + * The SPI_MODE_KERNEL_MASK has the SPI_MODE_USER_MASK counterpart, + * which is defined in 'include/uapi/linux/spi/spi.h'. + * The bits defined here are from bit 31 downwards, while in + * SPI_MODE_USER_MASK are from 0 upwards. + * These bits must not overlap. A static assert check should make sure of that. + * If adding extra bits, make sure to decrease the bit index below as well. + */ +#define SPI_MODE_KERNEL_MASK (~(BIT(30) - 1)) u32 mode; -#define SPI_CPHA 0x01 /* clock phase */ -#define SPI_CPOL 0x02 /* clock polarity */ -#define SPI_MODE_0 (0|0) /* (original MicroWire) */ -#define SPI_MODE_1 (0|SPI_CPHA) -#define SPI_MODE_2 (SPI_CPOL|0) -#define SPI_MODE_3 (SPI_CPOL|SPI_CPHA) -#define SPI_MODE_X_MASK (SPI_CPOL|SPI_CPHA) -#define SPI_CS_HIGH 0x04 /* chipselect active high? */ -#define SPI_LSB_FIRST 0x08 /* per-word bits-on-wire */ -#define SPI_3WIRE 0x10 /* SI/SO signals shared */ -#define SPI_LOOP 0x20 /* loopback mode */ -#define SPI_NO_CS 0x40 /* 1 dev/bus, no chipselect */ -#define SPI_READY 0x80 /* slave pulls low to pause */ -#define SPI_TX_DUAL 0x100 /* transmit with 2 wires */ -#define SPI_TX_QUAD 0x200 /* transmit with 4 wires */ -#define SPI_RX_DUAL 0x400 /* receive with 2 wires */ -#define SPI_RX_QUAD 0x800 /* receive with 4 wires */ -#define SPI_CS_WORD 0x1000 /* toggle cs after each word */ -#define SPI_TX_OCTAL 0x2000 /* transmit with 8 wires */ -#define SPI_RX_OCTAL 0x4000 /* receive with 8 wires */ -#define SPI_3WIRE_HIZ 0x8000 /* high impedance turnaround */ int irq; void *controller_state; void *controller_data; @@ -208,6 +202,10 @@ struct spi_device { */ }; +/* Make sure that SPI_MODE_KERNEL_MASK & SPI_MODE_USER_MASK don't overlap */ +static_assert((SPI_MODE_KERNEL_MASK & SPI_MODE_USER_MASK) == 0, + "SPI_MODE_USER_MASK & SPI_MODE_KERNEL_MASK must not overlap"); + static inline struct spi_device *to_spi_device(struct device *dev) { return dev ? container_of(dev, struct spi_device, dev) : NULL; @@ -624,7 +622,7 @@ struct spi_controller { /* * These hooks are for drivers that use a generic implementation - * of transfer_one_message() provied by the core. + * of transfer_one_message() provided by the core. */ void (*set_cs)(struct spi_device *spi, bool enable); int (*transfer_one)(struct spi_controller *ctlr, struct spi_device *spi, @@ -827,6 +825,7 @@ extern void spi_res_release(struct spi_controller *ctlr, * transfer. If 0 the default (from @spi_device) is used. * @bits_per_word: select a bits_per_word other than the device default * for this transfer. If 0 the default (from @spi_device) is used. + * @dummy_data: indicates transfer is dummy bytes transfer. * @cs_change: affects chipselect after this transfer completes * @cs_change_delay: delay between cs deassert and assert when * @cs_change is set and @spi_transfer is not the last in @spi_message @@ -939,6 +938,7 @@ struct spi_transfer { struct sg_table tx_sg; struct sg_table rx_sg; + unsigned dummy_data:1; unsigned cs_change:1; unsigned tx_nbits:3; unsigned rx_nbits:3; |