summaryrefslogtreecommitdiff
path: root/include/uapi/linux/nl80211.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/uapi/linux/nl80211.h')
-rw-r--r--include/uapi/linux/nl80211.h90
1 files changed, 89 insertions, 1 deletions
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h
index e23d78685a01..220694151434 100644
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -493,7 +493,12 @@
* This attribute is ignored if driver does not support roam scan.
* It is also sent as an event, with the BSSID and response IEs when the
* connection is established or failed to be established. This can be
- * determined by the STATUS_CODE attribute.
+ * determined by the %NL80211_ATTR_STATUS_CODE attribute (0 = success,
+ * non-zero = failure). If %NL80211_ATTR_TIMED_OUT is included in the
+ * event, the connection attempt failed due to not being able to initiate
+ * authentication/association or not receiving a response from the AP.
+ * Non-zero %NL80211_ATTR_STATUS_CODE value is indicated in that case as
+ * well to remain backwards compatible.
* @NL80211_CMD_ROAM: request that the card roam (currently not implemented),
* sent as an event when the card/driver roamed by itself.
* @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify
@@ -1819,6 +1824,49 @@ enum nl80211_commands {
*
* @NL80211_ATTR_PAD: attribute used for padding for 64-bit alignment
*
+ * @NL80211_ATTR_IFTYPE_EXT_CAPA: Nested attribute of the following attributes:
+ * %NL80211_ATTR_IFTYPE, %NL80211_ATTR_EXT_CAPA,
+ * %NL80211_ATTR_EXT_CAPA_MASK, to specify the extended capabilities per
+ * interface type.
+ *
+ * @NL80211_ATTR_MU_MIMO_GROUP_DATA: array of 24 bytes that defines a MU-MIMO
+ * groupID for monitor mode.
+ * The first 8 bytes are a mask that defines the membership in each
+ * group (there are 64 groups, group 0 and 63 are reserved),
+ * each bit represents a group and set to 1 for being a member in
+ * that group and 0 for not being a member.
+ * The remaining 16 bytes define the position in each group: 2 bits for
+ * each group.
+ * (smaller group numbers represented on most significant bits and bigger
+ * group numbers on least significant bits.)
+ * This attribute is used only if all interfaces are in monitor mode.
+ * Set this attribute in order to monitor packets using the given MU-MIMO
+ * groupID data.
+ * to turn off that feature set all the bits of the groupID to zero.
+ * @NL80211_ATTR_MU_MIMO_FOLLOW_MAC_ADDR: mac address for the sniffer to follow
+ * when using MU-MIMO air sniffer.
+ * to turn that feature off set an invalid mac address
+ * (e.g. FF:FF:FF:FF:FF:FF)
+ *
+ * @NL80211_ATTR_SCAN_START_TIME_TSF: The time at which the scan was actually
+ * started (u64). The time is the TSF of the BSS the interface that
+ * requested the scan is connected to (if available, otherwise this
+ * attribute must not be included).
+ * @NL80211_ATTR_SCAN_START_TIME_TSF_BSSID: The BSS according to which
+ * %NL80211_ATTR_SCAN_START_TIME_TSF is set.
+ * @NL80211_ATTR_MEASUREMENT_DURATION: measurement duration in TUs (u16). If
+ * %NL80211_ATTR_MEASUREMENT_DURATION_MANDATORY is not set, this is the
+ * maximum measurement duration allowed. This attribute is used with
+ * measurement requests. It can also be used with %NL80211_CMD_TRIGGER_SCAN
+ * if the scan is used for beacon report radio measurement.
+ * @NL80211_ATTR_MEASUREMENT_DURATION_MANDATORY: flag attribute that indicates
+ * that the duration specified with %NL80211_ATTR_MEASUREMENT_DURATION is
+ * mandatory. If this flag is not set, the duration is the maximum duration
+ * and the actual measurement duration may be shorter.
+ *
+ * @NL80211_ATTR_MESH_PEER_AID: Association ID for the mesh peer (u16). This is
+ * used to pull the stored data for mesh peer in power save state.
+ *
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
@@ -2201,6 +2249,18 @@ enum nl80211_attrs {
NL80211_ATTR_PAD,
+ NL80211_ATTR_IFTYPE_EXT_CAPA,
+
+ NL80211_ATTR_MU_MIMO_GROUP_DATA,
+ NL80211_ATTR_MU_MIMO_FOLLOW_MAC_ADDR,
+
+ NL80211_ATTR_SCAN_START_TIME_TSF,
+ NL80211_ATTR_SCAN_START_TIME_TSF_BSSID,
+ NL80211_ATTR_MEASUREMENT_DURATION,
+ NL80211_ATTR_MEASUREMENT_DURATION_MANDATORY,
+
+ NL80211_ATTR_MESH_PEER_AID,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
@@ -3462,6 +3522,12 @@ enum nl80211_bss_scan_width {
* was last updated by a received frame. The value is expected to be
* accurate to about 10ms. (u64, nanoseconds)
* @NL80211_BSS_PAD: attribute used for padding for 64-bit alignment
+ * @NL80211_BSS_PARENT_TSF: the time at the start of reception of the first
+ * octet of the timestamp field of the last beacon/probe received for
+ * this BSS. The time is the TSF of the BSS specified by
+ * @NL80211_BSS_PARENT_BSSID. (u64).
+ * @NL80211_BSS_PARENT_BSSID: the BSS according to which @NL80211_BSS_PARENT_TSF
+ * is set.
* @__NL80211_BSS_AFTER_LAST: internal
* @NL80211_BSS_MAX: highest BSS attribute
*/
@@ -3483,6 +3549,8 @@ enum nl80211_bss {
NL80211_BSS_PRESP_DATA,
NL80211_BSS_LAST_SEEN_BOOTTIME,
NL80211_BSS_PAD,
+ NL80211_BSS_PARENT_TSF,
+ NL80211_BSS_PARENT_BSSID,
/* keep last */
__NL80211_BSS_AFTER_LAST,
@@ -4467,6 +4535,22 @@ enum nl80211_feature_flags {
* %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests, which will set
* the ASSOC_REQ_USE_RRM flag in the association request even if
* NL80211_FEATURE_QUIET is not advertized.
+ * @NL80211_EXT_FEATURE_MU_MIMO_AIR_SNIFFER: This device supports MU-MIMO air
+ * sniffer which means that it can be configured to hear packets from
+ * certain groups which can be configured by the
+ * %NL80211_ATTR_MU_MIMO_GROUP_DATA attribute,
+ * or can be configured to follow a station by configuring the
+ * %NL80211_ATTR_MU_MIMO_FOLLOW_MAC_ADDR attribute.
+ * @NL80211_EXT_FEATURE_SCAN_START_TIME: This driver includes the actual
+ * time the scan started in scan results event. The time is the TSF of
+ * the BSS that the interface that requested the scan is connected to
+ * (if available).
+ * @NL80211_EXT_FEATURE_BSS_PARENT_TSF: Per BSS, this driver reports the
+ * time the last beacon/probe was received. The time is the TSF of the
+ * BSS that the interface that requested the scan is connected to
+ * (if available).
+ * @NL80211_EXT_FEATURE_SET_SCAN_DWELL: This driver supports configuration of
+ * channel dwell time.
*
* @NUM_NL80211_EXT_FEATURES: number of extended features.
* @MAX_NL80211_EXT_FEATURES: highest extended feature index.
@@ -4474,6 +4558,10 @@ enum nl80211_feature_flags {
enum nl80211_ext_feature_index {
NL80211_EXT_FEATURE_VHT_IBSS,
NL80211_EXT_FEATURE_RRM,
+ NL80211_EXT_FEATURE_MU_MIMO_AIR_SNIFFER,
+ NL80211_EXT_FEATURE_SCAN_START_TIME,
+ NL80211_EXT_FEATURE_BSS_PARENT_TSF,
+ NL80211_EXT_FEATURE_SET_SCAN_DWELL,
/* add new features before the definition below */
NUM_NL80211_EXT_FEATURES,