| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
SPEAr platforms now support DT and so must convert all drivers to support DT.
This patch adds DT probing support for Arasan Compact Flash controller and
updates its documentation too.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Calxeda highbank SATA phy has intermittent problems bringing up a link
with Gen3 drives. Retrying the phy hard reset can work-around this issue,
but each reset also disables spread spectrum support. The reset function
also needs to reprogram the phy to enable spread spectrum support.
Create a new driver based on ahci_platform to support the Calxeda Highbank
SATA controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The freescale V2 SATA controller checks if the received data length matches
the programmed length 'ttl', if not, it assumes that this is an error.
In ATAPI, the 'ttl' is based on max allocation length and not the actual
data transfer length, controller will raise 'DLM' (Data length Mismatch)
error bit in Hstatus register. Along with 'DLM', DE (Device error) and
FE (fatal Error) bits are also set in Hstatus register, 'E' (Internal Error)
bit is set in Serror register and CE (Command Error) and DE (Device error)
registers have the corresponding bit set. In this condition, we need to
clear errors in following way: in the service routine, based on 'DLM' flag,
HCONTROL[27] operation clears Hstatus, CE and DE registers, clear Serror
register.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Anju Bhartiya <Anju.Bhartiya@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Device Sleep is a feature as described in AHCI 1.3.1 Technical Proposal.
This feature enables an HBA and SATA storage device to enter the DevSleep
interface state, enabling lower power SATA-based systems.
Aggressive Device Sleep enables the HBA to assert the DEVSLP signal as
soon as there are no commands outstanding to the device and the port
specific Device Sleep idle timer has expired. This enables autonomous
entry into the DevSleep interface state without waiting for software
in power sensitive systems.
This patch enables Aggressive Device Sleep only if both host controller
and device support it.
Tested on AMD reference board together with Device Sleep supported device
sample.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Aaron Lu <aaron.lwe@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Define enumeration constants for IDENTIFY DEVICE words.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
It caused several reported regressions.
This reverts commit 91895b786e631ab47b618c901231f22b5a44115b.
|
|
The cache_type file in sysfs lets users configure the disk cache in
write-through or write-back modes. However, ata disks do not support
writing to the file because they do not implement the MODE SELECT
command.
This patch adds a translation from MODE SELECT (for the caching page
only) to the ATA SET FEATURES command. The set of changeable parameters
answered by MODE SENSE is also adjusted accordingly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Since the next patch will introduce support for MODE SELECT, it
makes sense to start advertising which bits are actually changeable.
For now, the answer is none.
Default parameters can also be reported, they are simply the same
as the current parameters.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Some other unlikely() should probably be removed as well. A fresh look
reveals an over-enthusiasm for unlikely() in libata-scsi.c.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Currently, SATA disk fua detection is disabled on default because most of
devices don't support this feature at that time. With the development of
technology, more and more SATA disks support this feature. So now we can enable
this detection on default.
Although fua detection is defined as a kernel module parameter, it is too hard
to set its value because it must be loaded and set before system starts up.
That needs to modify initrd file. So it is inconvenient for administrator who
needs to manage a huge number of servers.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Michael Eitelwein writes:
I have an external SATA drive that was slowed down by bridge limits. I
found a solution in a thread on this list posted in 2008: It introduces
whitelist entries in libata-core.c for devices with well working bridges
(e.g. email on Fri, 31 Oct 2008 01:45:27 -0400).
I added my device to this whitelist in a custom built kernel and it
works fine for weeks now. How can I have this device added on the
whitelist within the official kernel? Is this whitelist mechanism still
supported or is there a smarter way to achieve whitelisting?
I added the following whitelist entry for my Buffalo DriveStation
Quattro "BUFFALO HD-QSU2/R5":
/* Devices that do not need bridging limits applied */
{ "MTRON MSP-SATA*", NULL, ATA_HORKAGE_BRIDGE_OK, },
{ "BUFFALO HD-QSU2/R5", NULL, ATA_HORKAGE_BRIDGE_OK, },
Reported-by: Michael Eitelwein <michael@eitelwein.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Building Linux for an ASUS Eee PC 701 4G with
ata2.00: CFA: SILICONMOTION SM223AC, , max UDMA/66
ata2.00: 7815024 sectors, multi 0: LBA
ata2.00: configured for UDMA/66
scsi 1:0:0:0: Direct-Access ATA SILICONMOTION SM n/a PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 7815024 512-byte logical blocks: (4.00 GB/3.72 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 1:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg0 type 0
I followed the advice to not use the deprecated old PATA subsystem
ATA/ATAPI/MFM/RLL support (DEPRECATED) --->
and use the ATA subsystem instead.
Serial ATA and Parallel ATA drivers --->
Unfortunately I needed several tries to find out, that I needed the SFF
menu I had not selected before because I had never heard that term
before. I think it would have helped me, to have PATA or legacy IDE in
that item’s name.
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Commit 30dcf76acc695cbd2fa919e294670fe9552e16e7 mistakenly dropped
the code to get an initial gtm for the IDE channel. This caused the
following problem for Sergei:
http://marc.info/?l=linux-kernel&m=134484963618457&w=2
Fix this by adding the call back in ata_acpi_bind_host, and due to
this, the ata_ap_acpi_handle is modified accordingly.
Tested-by: Sergei Trofimovich <slyich@gmail.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch adds the IDE-mode SATA Device IDs for the Intel Lynx Point-LP PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch adds the AHCI-mode SATA Device IDs for the Intel Lynx Point-LP PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The mainboard MSI E350DM-E33 is advertised with 6 SATA ports.
As it turns out, two of them seem to be driven by on-board
SATA<->PATA converters. If a disk drive is connected to one
of them kernel uses UDMA/33 mode due to cable detection:
[ 34.550823] scsi4 : pata_atiixp
[ 34.555517] scsi5 : pata_atiixp
[ 34.555942] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf100 irq 14
[ 34.555948] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf108 irq 15
...
[ 35.040799] ata5.00: ATA-8: WDC WD20EADS-00R6B0, 01.00A01, max UDMA/133
[ 35.040806] ata5.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 35.040817] ata5.00: limited to UDMA/33 due to 40-wire cable
[ 35.049166] ata5.00: configured for UDMA/33
[ 35.049402] scsi 4:0:0:0: Direct-Access ATA WDC WD20EADS-00R 01.0 PQ: 0 ANSI: 5
This patch forces "short cable" mode on this board, as it seems clear that
the on-board SATA<->PATA "cable" is short.
With this patch the disk is configured for UDMA/100:
[ 5.976756] ata5.00: ATA-8: WDC WD20EADS-00R6B0, 01.00A01, max UDMA/133
[ 5.996434] ata5.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 6.024787] ata5.00: configured for UDMA/100
Testing revealed no transfer issues.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Make ahci_dev_classify available to the ahci platform driver for custom
hard reset function.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
|
|
Following a report of a crash during an automount expire I found that
the locking in fs/autofs4/expire.c:get_next_positive_subdir() was wrong.
Not only is the locking wrong but the function is more complex than it
needs to be.
The function is meant to calculate (and dget) the next entry in the list
of directories contained in the root of an autofs mount point (an autofs
indirect mount to be precise). The main problem was that the d_lock of
the owner of the list was not being taken when walking the list, which
lead to list corruption under load. The only other lock that needs to
be taken is against the next dentry candidate so it can be checked for
usability.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull VFIO fix from Alex Williamson:
"Just a trivial patch to include vfio.h in the installed headers so we
can complete userspace integration into QEMU."
* tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio:
vfio: Include vfio.h in installed headers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse updates from Miklos Szeredi.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: verify all ioctl retry iov elements
fuse: add missing INIT flag descriptions
fuse: add missing INIT flags
fuse: update attributes on aio_read
fuse: invalidate inode mapping if mtime changes
fuse: add FUSE_AUTO_INVAL_DATA init flag
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fix from Konrad Rzeszutek Wilk:
"Way back in v3.5 we added a mechanism to populate back pages that were
released (they overlapped with MMIO regions), but neglected to reserve
the proper amount of virtual space for extend_brk to work properly.
Coincidentally some other commit aligned the _brk space to larger area
so I didn't trigger this until it was run on a machine with more than
2GB of MMIO space."
* On machines with large MMIO/PCI E820 spaces we fail to boot b/c
we failed to pre-allocate large enough virtual space for extend_brk.
* tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.
|
|
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: intc: Handle domain association for sparseirq pre-allocated vectors.
sh: sh7269: Fix LCD pinmux
sh: dma: fix request_irq usage
|
|
Moved to djbw@fb.com
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Dan Williams <djbw@fb.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When dumping "Code: " sections from an oops, the trapping instruction
%rip points to can be a string copy
2b:* f3 a5 rep movsl %ds:(%rsi),%es:(%rdi)
and the line contain a bunch of ":". Current "cut" selects only the and
the second field output looks funnily overlaid this:
2b:* f3 a5 rep movsl %ds <-- trapping instruction:(%rsi),%es:(%rdi
Fix this by selecting the remaining fields too.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kbuild@vger.kernel.org
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull two slave-dmaengine fixes from Vinod Koul:
"One fixes the correct use of clock API in imx driver and the other
enables clock for tegra driver, which is used for other tegra driver
conversion to dmanegine in -next."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: enable/disable dma clock
dma: imx-dma: Fix kernel crash due to missing clock conversion
|
|
Pull more drm fixes from Dave Airlie:
"Just some intel and nouveau ones this time, intel has more edp panel
fixes for macbooks and nouveau has a suspend/resume regression fix in
there."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
drm/nve0/fifo: add support for the flip completion swmthd
|
|
Pull two sparc fixes from David S. Miller.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Be less verbose during vmemmap population.
sparc64: do not clobber personality flags in sys_sparc64_personality()
|
|
git://git.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/nve0/fifo: add support for the flip completion swmthd
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel Vetter writes:
"A few important fixers:
- fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai)
- make the retina mbp work (ignore bogus edp bpc value in vbt)
- fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula)
- fix an edp panel power sequence regression, fixes the new macbook air
- apply the tlb invalidate w/a
Otherwise we still have another gmbus regression (patches are awaiting
tested-bys) and there's something odd going with some rare systems not
entering rc6 often enough (and hence blowing through too much power). It
seems to be a timing-related issue and can be mitigated by frobbing the
magic tuning parameters. We're still working on that one. Also, we still
have some fallout from the hw context support, but you can only hit that
with mesa master."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
|
|
On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.
This mimicks Yinghai Lu's x86 commit c2b91e2eec9678dbda274e906cc32ea8f711da3b
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.
This decreases the output by an order of 16.
Also demote this to KERN_DEBUG.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When invalidating the TLBs it is documentated as requiring a post-sync
write. Failure to do so seems to result in a GPU hang.
Exposure to this hang on IVB seems to be a result of removing the extra
stalls required for SNB pipecontrol workarounds:
commit 6c6cf5aa9c583478b19e23149feaa92d01fb8c2d
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 20 18:02:28 2012 +0100
drm/i915: Only apply the SNB pipe control w/a to gen6
Note: Manually switch the pipe_control cmd to 4 dwords to avoid a
(silent) functional conflict with -next. This way will get a loud (but
conflict with next (since the scratch_addr has been deleted there).
Reported-and-tested-by: yex.tian@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: added note about merge conflict with -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
eDP is tons of fun. It turns out that at least the new MacBook Air 5,1
model absolutely doesn't like the new force vdd dance we've introduced
in
commit 6cb49835da0426f69a2931bc2a0a8156344b0e41
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun May 20 17:14:50 2012 +0200
drm/i915: enable vdd when switching off the eDP panel
But that patch also tried to fix some neat edp sequence issue with the
force_vdd timings. Closer inspection reveals that we've raised
force_vdd only to do the aux channel communication dp_sink_dpms. If we
move the edp_panel_off below that, we don't need any force_vdd for the
disable sequence, which makes the Air happy.
Unfortunately the reporter of the original bug that the above commit
fixed is travelling, so we can't test whether this regresses things.
But my theory is that since we don't check for any power-off ->
force_vdd-on delays in edp_panel_vdd_on, this was the actual
root-cause of this failure. With that force_vdd dance completely
eliminated, I'm hopeful the original bug stays fixed, too.
For reference the old bug, which hopefully doesn't get broken by this:
https://bugzilla.kernel.org/show_bug.cgi?id=43163
In any case, regression fixers win over plain bugfixes, so this needs
to go in asap.
v2: The crucial pieces seems to be to clear the force_vdd flag
uncoditionally, too, in edp_panel_off. Looks like this is left behind
by the firmware somehow.
v3: The Apple firmware seems to switch off the panel on it's own, hence
we still need to keep force_vdd on, but properly clear it when switching
the panel off.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671
Tested-by: Roberto Romer <sildurin@gmail.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Tested-by: Keith Packard <keithp@keithp.com>
Cc: stable@vger.kernel.org
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"Included are bug fixes and a patch to enable system call filtering
with BPF."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/compat: fix mmap compat system calls
s390/compat: fix compat wrappers for process_vm system calls
s390: do not clobber personality flags in sys_32_personality()
s390/seccomp: add support for system call filtering using BPF
s390/sclp_sdias: Add missing break and "fall through"
s390/mm: remove MAX_PHYSADDR_BITS define
|
|
Pull drm fixes from Dave Airlie:
"Radeon and intel fixes mostly, one fix to the mgag200 driver to not
hang on certain server variants."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (32 commits)
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
drm/mgag200: fix G200ER pll picking algorithm
drm/edid: Fix potential memory leak in edid_load()
drm/udl: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
drm/radeon/kms: allow "invalid" DB formats as a means to disable DB
...
|
|
Commit 7212157267 ("GPIO: gpio-pxa: fix devicetree functions") added an
"xlate" function pointer to the irq_domain_ops, but this function is nor
declared or defined anywhere when CONFIG_OF is disabled, causing the
build error:
drivers/gpio/gpio-pxa.c:532:11: error: 'irq_domain_xlate_twocell' undeclared here (not in a function)
Extending the DT-only code section to cover the irq_domain_ops and the
pxa_gpio_dt_ids solves this problem and makes it clearer which code is
actually used without DT.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This fix is a backport from the reworked nouveau driver. It masks off the
engines we're not expecting to use before attempting a channel kickoff.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
The copy engine exhibits random memory corruption in at least one case, the
GeForce 320M (nv50, 0xaf) in the MacBookAir3,1.
This patch omits creating the engine for the specific chipset, falling back
to M2MF, which kills the symptoms.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Fixes screen being black after changing performance level.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: stable@vger.kernel.org [3.5+]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
At least partially fixes DP output detection on W530. Not sure if more
issues remain, or if my adaptor is just behaving weirdly (it does that
sometimes).
In any case, this patch is necessary.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Christoph Bumiller <e0425955@student.tuwien.ac.at>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
into drm-fixes
Alex Deucher writes:
This is the current set of radeon fixes for 3.6. Nothing too major.
Highlights:
- various display fixes
- some SI fixes
- new SI pci ids
- major VM fix
- CS checker support for MSAA
I've tested on a number of cards across generations and noticed no problems.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
|
|
i2c_add_adapter() may do i2c transfers on the bus to detect supported
devices. Therefore the adapter needs to be all set before adding it. This
was not the case for the bit-banging fallback, resulting in an oops if the
device detection GMBUS transfers timed out. Fix the issue by calling
i2c_add_adapter() only after intel_gpio_setup().
LKML-Reference: <5021F00B.7000503@ionic.de>
Tested-by: Mihai Moldovan <ionic@ionic.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Dmitrii Cherkasov <DCherkasov@luxsoft.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Returns a snapshot of the GPU clock counter. Needed
for certain OpenGL extensions.
v2: agd5f
- address Jerome's comments
- add function documentation
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Most of the checking seems to be in place already. As you can see,
log2(number of samples) resides in LAST_LEVEL.
This is required for MSAA support (namely for depth-stencil resolve and
blitting between MSAA resources).
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Virtual address need to be fenced to know when we can safely remove it.
This patch also properly clear the pagetable. Previously it was
serouisly broken.
Kernel 3.5/3.4 need a similar patch but adapted for difference in mutex locking.
v2: For to update pagetable when unbinding bo (don't bailout if
bo_va->valid is true).
v3: Add kernel 3.5/3.4 comment.
v4: Fix compilation warnings.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Better safe than sorry.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
|
