| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
According to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency.
So assuming e.g. a 16 bit counter this means that if base_unit is set to 1,
after 65535 input clock-cycles the counter has been increased from 0 to
65535 and it will overflow on the next cycle, so it will overflow after
every 65536 clock cycles and thus the calculations done in
pwm_lpss_prepare() should use 65536 and not 65535.
This commit fixes this. Note this also aligns the calculations in
pwm_lpss_prepare() with those in pwm_lpss_get_state().
Note this effectively reverts commit 684309e5043e ("pwm: lpss: Avoid
potential overflow of base_unit"). The next patch in this series really
fixes the potential overflow of the base_unit value.
Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-4-hdegoede@redhat.com
|
|
The DSDTs on most Cherry Trail devices have an ugly clutch where the PWM
controller gets turned off from the _PS3 method of the graphics-card dev:
Method (_PS3, 0, Serialized) // _PS3: Power State 3
{
...
PWMB = PWMC /* \_SB_.PCI0.GFX0.PWMC */
PSAT |= 0x03
Local0 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
...
}
Where PSAT is the power-status register of the PWM controller.
Since the i915 driver will do a pwm_get on the pwm device as it uses it to
control the LCD panel backlight, there is a device-link marking the i915
device as a consumer of the pwm device. So that the PWM controller will
always be suspended after the i915 driver suspends (which is the right
thing to do). This causes the above GFX0 PS3 AML code to run before
acpi_lpss.c calls acpi_lpss_save_ctx().
So on these devices the PWM controller will already be off when
acpi_lpss_save_ctx() runs. This causes it to read/save all 1-s (0xffffffff)
as ctx register values.
When these bogus values get restored on resume the PWM controller actually
keeps working, since most bits are reserved, but this does set bit 3 of
the LPSS General purpose register, which for the PWM controller has the
following function: "This bit is re-used to support 32kHz slow mode.
Default is 19.2MHz as PWM source clock".
This causes the clock of the PWM controller to switch from 19.2MHz to
32KHz, which is a slow-down of a factor 600. Surprisingly enough so far
there have been few bug reports about this. This is likely because the
i915 driver was hardcoding the PWM frequency to 46 KHz, which divided
by 600 would result in a PWM frequency of approx. 78 Hz, which mostly
still works fine. There are some bug reports about the LCD backlight
flickering after suspend/resume which are likely caused by this issue.
But with the upcoming patch-series to finally switch the i915 drivers
code for external PWM controllers to use the atomic API and to honor
the PWM frequency specified in the video BIOS (VBT), this becomes a much
bigger problem. On most cases the VBT specifies either 200 Hz or 20
KHz as PWM frequency, which with the mentioned issue ends up being either
1/3 Hz, where the backlight actually visible blinks on and off every 3s,
or in 33 Hz and horrible flickering of the backlight.
There are a number of possible solutions to this problem:
1. Make acpi_lpss_save_ctx() run before GFX0._PS3
Pro: Clean solution from pov of not medling with save/restore ctx code
Con: As mentioned the current ordering is the right thing to do
Con: Requires assymmetry in at what suspend/resume phase we do the save vs
restore, requiring more suspend/resume ordering hacks in already
convoluted acpi_lpss.c suspend/resume code.
2. Do some sort of save once mode for the LPSS ctx
Pro: Reasonably clean
Con: Needs a new LPSS flag + code changes to handle the flag
3. Detect we have failed to save the ctx registers and do not restore them
Pro: Not PWM specific, might help with issues on other LPSS devices too
Con: If we can get away with not restoring the ctx why bother with it at
all?
4. Do not save the ctx for CHT PWM controllers
Pro: Clean, as simple as dropping a flag?
Con: Not so simple as dropping a flag, needs a new flag to ensure that
we still do lpss_deassert_reset() on device activation.
5. Make the pwm-lpss code fixup the LPSS-context registers
Pro: Keeps acpi_lpss.c code clean
Con: Moves knowledge of LPSS-context into the pwm-lpss.c code
1 and 5 both do not seem to be a desirable way forward.
3 and 4 seem ok, but they both assume that restoring the LPSS-context
registers is not necessary. I have done a couple of test and those do
show that restoring the LPSS-context indeed does not seem to be necessary
on devices using s2idle suspend (and successfully reaching S0i3). But I
have no hardware to test deep / S3 suspend. So I'm not sure that not
restoring the context is safe.
That leaves solution 2, which is about as simple / clean as 3 and 4,
so this commit fixes the described problem by implementing a new
LPSS_SAVE_CTX_ONCE flag and setting that for the CHT PWM controllers.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-3-hdegoede@redhat.com
|
|
The DSDTs on most Cherry Trail devices have an ugly clutch where the PWM
controller gets poked from the _PS0 method of the graphics-card device:
Local0 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
If (((Local0 & 0x03) == 0x03))
{
PSAT &= 0xFFFFFFFC
Local1 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
RSTA = Zero
RSTF = Zero
RSTA = One
RSTF = One
PWMB |= 0xC0000000
PWMC = PWMB /* \_SB_.PCI0.GFX0.PWMB */
}
Where PSAT is the power-status register of the PWM controller, so if it
is in D3 when the GFX0 device's PS0 method runs then it will turn it on
and restore the PWM ctrl register value it saved from its PS3 handler.
Note not only does it restore it, it ors it with 0xC0000000 turning it
on at a time where we may not want it to get turned on at all.
The pwm_get call which the i915 driver does to get a reference to the
PWM controller, already adds a device-link making the GFX0 device a
consumer of the PWM device. So it should already have been resumed when
the above AML runs and the AML should thus not do its undesirable poking
of the PWM controller register.
But the PCI core powers on PCI devices in the no-irq resume phase and
thus calls the troublesome PS0 method in the no-irq resume phase.
Where as LPSS devices by default are resumed in the early resume phase.
This commit sets the resume_from_noirq flag in the bsw_pwm_dev_desc
struct, so that Cherry Trail PWM controllers will be resumed in the
no-irq phase. Together with the device-link added by the pwm-get this
ensures that the PWM controller will be on when the troublesome PS0
method runs, which stops it from poking the PWM controller.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-2-hdegoede@redhat.com
|
|
Streamline the modeset init by removing the extra init layer.
No functional changes, which means the cleanup path looks hideous.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/62c32c35683b843ecdc2eca2bd2d3e62cb705e96.1599056955.git.jani.nikula@intel.com
|
|
Split out a separate display function for driver remove after gem
deinitialization. Note that the sequence is not symmetric with
init. However use similar naming as that reflects the deinit sequence.
No functional changes.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/197fa7e488b412e147ff0fe9440c48811888f1a6.1599056955.git.jani.nikula@intel.com
|
|
With the intel_modeset_* probe functions clarified, we can continue with
moving more related calls to the right layer:
- drm_vblank_init()
- intel_bios_init()
- intel_vga_register()
- intel_csr_ucode_init()
Unfortunately, for the time being, we also need to move a call to the
*wrong* layer: the power domain init.
No functional changes.
v2: move probe failure while at it, power domain init
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/da229ffbed64983f002605074533c8b2878d17ee.1599056955.git.jani.nikula@intel.com
|
|
Turn current intel_modeset_init() to a pre-gem init function, and add a
new intel_modeset_init() function and move all post-gem modeset init
there, in the correct layer. No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5f4603f2c0216dba980338f00e0bfa791b526231.1599056955.git.jani.nikula@intel.com
|
|
In commit 4f0b4352bd26 ("drm/i915: Extract cdclk requirements checking
to separate function") the order of force_min_cdclk_changed check and
intel_modeset_checks(), was reversed. This broke the mechanism to
immediately force a new CDCLK minimum, and lead to driver probe
errors for display audio on GLK platform with 5.9-rc1 kernel. Fix
the issue by moving intel_modeset_checks() call later.
[vsyrjala: It also broke the ability of planes to bump up the cdclk
and thus could lead to underruns when eg. flipping from 32bpp to
64bpp framebuffer. To be clear, we still compute the new cdclk
correctly but fail to actually program it to the hardware due to
intel_set_cdclk_{pre,post}_plane_update() not getting called on
account of state->modeset==false.]
Fixes: 4f0b4352bd26 ("drm/i915: Extract cdclk requirements checking to separate function")
BugLink: https://github.com/thesofproject/linux/issues/2410
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200901151036.1312357-1-kai.vehmanen@linux.intel.com
|
|
Now that all the groundwork has been laid, we can turn on HDCP 1.4 over
MST. Everything except for toggling the HDCP signalling and HDCP 2.2
support is the same as the DP case, so we'll re-use those callbacks
Cc: Juston Li <juston.li@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-12-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-13-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-13-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-15-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-17-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-17-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-18-sean@poorly.run #v7
Changes in v2:
-Toggle HDCP from encoder disable/enable
-Don't disable HDCP on MST connector destroy, leave that for encoder
disable, just ensure the check_work routine isn't running any longer
Changes in v3:
-Place the shim in the new intel_dp_hdcp.c file (Ville)
Changes in v4:
-Actually use the mst shim for mst connections (Juston)
-Use QUERY_STREAM_ENC_STATUS MST message to verify channel is encrypted
Changes in v5:
-Add sleep on disable signalling to match hdmi delay
Changes in v6:
-Disable HDCP over MST on GEN12+ since I'm unsure how it should work and I
don't have hardware to test it
Changes in v7:
-Remove hdcp2 shims for MST in favor of skipping hdcp2 init (Ramalingam)
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-18-sean@poorly.run
|
|
De-duplicate the HDCP version code for each connector and print it for
all connectors.
Cc: Juston Li <juston.li@intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Juston Li <juston.li@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227185714.171466-1-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-16-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-16-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-17-sean@poorly.run #v7
Changes in v4:
- Added to the set
Changes in v5:
-Print "No connector support" for hdcp sink capability as well (Ram)
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-17-sean@poorly.run
|
|
Used to query whether an MST stream is encrypted or not.
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-14-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-15-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-15-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-16-sean@poorly.run #v7
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-16-sean@poorly.run #v8
Changes in v4:
-Added to the set
Changes in v5:
-None
Changes in v6:
-Use FIELD_PREP to generate request buffer bitfields (Lyude)
-Add mst selftest and dump/decode_sideband_req for QSES (Lyude)
Changes in v7:
-None
Changes in v8:
-Reverse the parsing on the hdcp_*x_device_present bits and leave
breadcrumb in case this is incorrect (Anshuman)
Changes in v8.5:
-s/DRM_DEBUG_KMS/drm_dbg_kms/ (Lyude)
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819143133.46232-1-sean@poorly.run
|
|
Currently we derive the connector from digital port in check_link(). For
MST, this isn't sufficient since the digital port passed into the
function can have multiple connectors downstream. This patch adds
connector to the check_link() arguments so we have it when we need it.
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-13-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-14-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-14-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-15-sean@poorly.run #v7
Changes in v4:
-Added to the set
Changes in v5:
-None
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-15-sean@poorly.run
|
|
This patch plumbs port through hdcp init instead of relying on
intel_attached_encoder() to return a non-NULL encoder which won't work
for MST connectors.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-13-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-13-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-14-sean@poorly.run #v7
Changes in v5:
-Added to the set
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-14-sean@poorly.run
|
|
These functions are all the same for dp and dp_mst, so move them into a
dedicated file for both sst and mst to use.
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-11-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-12-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-12-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-12-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-12-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-12-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-13-sean@poorly.run #v7
Changes in v2:
-None
Changes in v3:
-Created intel_dp_hdcp.c for the shared functions to live (Ville)
Changes in v4:
-Rebased on new drm logging change
Changes in v5:
-None
Changes in v6:
-None
Changes in v7:
-Rebased patch
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-13-sean@poorly.run
|
|
In order to act upon content_protection property changes, we'll need to
implement the .update_pipe() hook. We can re-use intel_ddi_update_pipe
for this
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-10-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-11-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-11-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-11-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-11-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-11-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-12-sean@poorly.run #v7
Changes in v2:
-None
Changes in v3:
-None
Changes in v4:
-None
Changes in v5:
-None
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-12-sean@poorly.run
|
|
Although DP_MST fake encoders are not subclassed from digital ports,
they are associated with them. Support these encoders.
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-9-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-10-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-10-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-10-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-10-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-10-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-11-sean@poorly.run #v7
Changes in v2:
-None
Changes in v3:
-None
Changes in v4:
-None
Changes in v5:
-None
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-11-sean@poorly.run
|
|
This patch is required for HDCP over MST. If a port is being used for
multiple HDCP streams, we don't want to fully disable HDCP on a port if
one of them is disabled. Instead, we just disable the HDCP signalling on
that particular pipe and exit early. The last pipe to disable HDCP will
also bring down HDCP on the port.
In order to achieve this, we need to keep a refcount in intel_digital_port
and protect it using a new hdcp_mutex.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-8-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-9-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-9-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-9-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-9-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-9-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-10-sean@poorly.run #v7
Changes in v2:
-Move the toggle_signalling call into _intel_hdcp_disable so it's called from check_work
Changes in v3:
-None
Changes in v4:
-None
Changes in v5:
-Change WARN_ON to drm_WARN_ON
Changes in v6:
-None
Changes in v7:
-Split minor intel_hdcp_disable refactor into separate patch (Ramalingam)
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-10-sean@poorly.run
|
|
Add an out label and un-indent hdcp disable in preparation for
hdcp_mutex. No functional changes
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-9-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-9-sean@poorly.run #v7
Changes in v7:
-Split into separate patch (Ramalingam)
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-9-sean@poorly.run
|
|
This patch adds some protection against connectors being destroyed
before the HDCP workers are finished.
For check_work, we do a synchronous cancel after the connector is
unregistered which will ensure that it is finished before destruction.
In the case of prop_work, we can't do a synchronous wait since it needs
to take connection_mutex which could cause deadlock. Instead, we'll take
a reference on the connector when scheduling prop_work and give it up
once we're done.
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-8-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-8-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-8-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-8-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-8-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-8-sean@poorly.run #v7
Changes in v2:
-Added to the set
Changes in v3:
-Change the WARN_ON condition in intel_hdcp_cleanup to allow for
initializing connectors as well
Changes in v4:
-None
Changes in v5:
-Change WARN_ON to drm_WARN_ON
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-8-sean@poorly.run
|
|
This is a bit of housecleaning for a future patch. Instead of sprinkling
hdcp->value assignments and prop_work scheduling everywhere, introduce a
function to do it for us.
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-7-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-7-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-7-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-7-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-7-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-7-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-7-sean@poorly.run #v7
Changes in v2:
-None
Changes in v3:
-None
Changes in v4:
-Rebased on top of drm_* logging changes
Changes in v5:
-Change WARN_ON to drm_WARN_ON
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-7-sean@poorly.run
|
|
Instead of using intel_dig_port's encoder pipe to determine which
transcoder to toggle signalling on, use the cpu_transcoder field already
stored in intel_hdmi.
This is particularly important for MST.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-6-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-6-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-6-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-6-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-6-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-6-sean@poorly.run #v7
Changes in v2:
-Added to the set
Changes in v3:
-s/hdcp/hdmi/ in commit msg (Ram)
Changes in v4:
-Rebased on intel_de_(read|write) change
Changes in v5:
-Update hdcp->cpu_transcoder in intel_hdcp_enable so it works with pipe != 0
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-6-sean@poorly.run
|
|
Instead of hand rolling the transfer ourselves in the hdcp hook, inspect
aux messages and add the aksv flag in the aux transfer hook.
IIRC, this was the original implementation and folks wanted this hack to
be isolated to the hdcp code, which makes sense.
However in testing an LG monitor on my desk, I noticed it was passing
back a DEFER reply. This wasn't handled in our hand-rolled code and HDCP
auth was failing as a result. Instead of copy/pasting all of the retry
logic and delays from drm dp helpers, let's just use the helpers and hide
the aksv select as best as we can.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-3-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-5-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-5-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-5-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-5-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-5-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-5-sean@poorly.run #v7
Changes in v2:
-Remove 'generate' in intel_dp_aux_generate_xfer_flags, make arg const (Ville)
-Bundle Aksv if statement together (Ville)
-Rename 'txbuf' to 'aksv' (Ville)
Changes in v3:
-None
Changes in v4:
-None
Changes in v5:
-None
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-5-sean@poorly.run
|
|
HDCP signalling should not be left on, WARN if it is
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-4-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-4-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-4-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-4-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-4-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-4-sean@poorly.run #v7
Changes in v2:
-Added to the set in lieu of just clearing the bit
Changes in v3:
-None
Changes in v4:
-None
Changes in v5:
-Change WARN_ON to drm_WARN_ON
Changes in v6:
-None
Changes in v7:
-Rebased, variable name changed from 'ctl' to 'val'
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-4-sean@poorly.run
|
|
On HDCP disable, clear the repeater bit. This ensures if we connect a
non-repeater sink after a repeater, the bit is in the state we expect.
Fixes: ee5e5e7a5e0f ("drm/i915: Add HDCP framework + base implementation")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.17+
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-3-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-3-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-3-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-3-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-3-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-3-sean@poorly.run #v7
Changes in v2:
-Added to the set
Changes in v3:
-None
I had previously agreed that clearing the rep_ctl bits on enable would
also be a good idea. However when I committed that idea to code, it
didn't look right. So let's rely on enables and disables being paired
and everything outside of that will be considered a bug
Changes in v4:
-s/I915_(READ|WRITE)/intel_de_(read|write)/
Changes in v5:
-None
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-3-sean@poorly.run
|
|
This patch fixes a few bugs:
1- We weren't taking into account sha_leftovers when adding multiple
ksvs to sha_text. As such, we were or'ing the end of ksv[j - 1] with
the beginning of ksv[j]
2- In the sha_leftovers == 2 and sha_leftovers == 3 case, bstatus was
being placed on the wrong half of sha_text, overlapping the leftover
ksv value
3- In the sha_leftovers == 2 case, we need to manually terminate the
byte stream with 0x80 since the hardware doesn't have enough room to
add it after writing M0
The upside is that all of the HDCP supported HDMI repeaters I could
find on Amazon just strip HDCP anyways, so it turns out to be _really_
hard to hit any of these cases without an MST hub, which is not (yet)
supported. Oh, and the sha_leftovers == 1 case works perfectly!
Fixes: ee5e5e7a5e0f ("drm/i915: Add HDCP framework + base implementation")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.17+
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-2-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-2-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-2-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-2-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-2-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-2-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-2-sean@poorly.run #v7
Changes in v2:
-None
Changes in v3:
-None
Changes in v4:
-Rebased on intel_de_write changes
Changes in v5:
-None
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-2-sean@poorly.run
|
|
I'll need this in IGT to identify the different kind of GTs and apply
the right performance query configuration.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200828133125.157171-1-lionel.g.landwerlin@intel.com
|
|
icl_combo_phy_verify_state
Clang warns:
drivers/gpu/drm/i915/display/intel_combo_phy.c:268:3: warning: variable
'ret' is uninitialized when used here [-Wuninitialized]
ret &= check_phy_reg(dev_priv, phy, ICL_PORT_TX_DW8_LN0(phy),
^~~
drivers/gpu/drm/i915/display/intel_combo_phy.c:261:10: note: initialize
the variable 'ret' to silence this warning
bool ret;
^
= 0
1 warning generated.
In practice, the bug this warning appears to be concerned with would not
actually matter because ret gets initialized to the return value of
cnl_verify_procmon_ref_values. However, that does appear to be a bug
since it means the first hunk of the patch this fixes won't actually do
anything (since the values of check_phy_reg won't factor into the final
ret value). Initialize ret to true then make all of the assignments a
bitwise AND with itself so that the function always does what it should
do.
Fixes: 239bef676d8e ("drm/i915/display: Implement new combo phy initialization step")
Link: https://github.com/ClangBuiltLinux/linux/issues/1094
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200828202830.7165-1-jose.souza@intel.com
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
|
|
Update with latest tuning in the table.
v3: Fix values of to last columns.
BSpec: 21257
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826201549.83658-3-jose.souza@intel.com
|
|
Reusing icl_get_combo_buf_trans() for eDP was causing the wrong table
being used when the eDP port don't support low power voltage swing table.
v2: Only use icl_combo_phy_ddi_translations_edp_hbr3 if low_vswing is
set as EHL combo phy supports HBR3 (Matt R)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826201549.83658-2-jose.souza@intel.com
|
|
Reusing icl_get_combo_buf_trans() for eDP was causing the wrong table
being used when the eDP port don't support low power voltage swing table.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826201549.83658-1-jose.souza@intel.com
|
|
TGL made stepping a litte mess, workarounds refer to the stepping of
the IP(GT or Display) not of the GPU stepping so it would already
require the same solution as used in commit 96c5a15f9f39
("drm/i915/kbl: Fix revision ID checks").
But to make things even more messy it have a different IP stepping
mapping between SKUs and the same stepping revision of GT do not match
the same HW between TGL U/Y and regular TGL.
So it was required to have 2 different macros to check GT WAs while
for Display we are able to use just one macro that uses the right
revids table.
All TGL workarounds checked and updated accordingly.
v2:
- removed TODO to check if WA 14010919138 applies to regular TGL.
- fixed display stepping in regular TGL (Anusha)
BSpec: 52890
BSpec: 55378
BSpec: 44455
Reviewed-by: Anusha Srivatsa <anusha.srivtsa@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Penne Lee <penne.y.lee@intel.com>
Cc: Guangyao Bai <guangyao.bai@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200827233943.400946-1-jose.souza@intel.com
|
|
Supported and enabled are different things so printing both.
v3: using drrs->type instead of vbt.drrs_type
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Srinivas K <srinivasx.k@intel.com>
Cc: Hariom Pandey <hariom.pandey@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200825171331.17971-3-jose.souza@intel.com
|
|
Changes in the configuration could cause PSR to be compatible and
enabled so driver must also be able to disable DRRS when doing
fastsets.
v2: Fixed name of DRRS compute function (Anshuman)
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/209
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/173
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/209
Cc: Srinivas K <srinivasx.k@intel.com>
Cc: Hariom Pandey <hariom.pandey@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200825171331.17971-2-jose.souza@intel.com
|
|
DRRS and PSR can't be enable together, so giving preference to PSR
as it allows more power-savings by complete shutting down display,
so to guarantee this, it should compute DRRS state after compute PSR.
Cc: Srinivas K <srinivasx.k@intel.com>
Cc: Hariom Pandey <hariom.pandey@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200825171331.17971-1-jose.souza@intel.com
|
|
There is a spelling mistake in a drm_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200810095952.60968-1-colin.king@canonical.com
|
|
Enable HW Default flip for small PL.
bspec: 52890
bspec: 53508
bspec: 53273
v2: rebase to drm-tip
v3: move from ctx to gt workarounds. Remove whitelist.
v4: move to rcs WA init
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826025724.20944-1-clinton.a.taylor@intel.com
|
|
HDCP code doesn't require to access power_well internal stuff,
instead it should use the intel_display_power_well_is_enabled()
to get the status of desired power_well.
No functional change.
v2:
- used with_intel_runtime_pm instead of get/put. [Jani]
v3:
- rebased.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200805114521.867-3-anshuman.gupta@intel.com
|
|
Currently intel_hdcp_update_pipe() is also getting called for non-hdcp
connectors and get through its conditional code flow, which is completely
unnecessary for non-hdcp connectors, therefore it make sense to
have an early return. No functional change.
v2:
- rebased.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200805114521.867-2-anshuman.gupta@intel.com
|
|
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Our variety of defined gpu commands have the actual
command id field and possibly length and flags applied.
We did start to apply the mask during initialization of
the cmd descriptors but forgot to also apply it on comparisons.
Fix comparisons in order to properly deny access with
associated commands.
v2: fix lri with correct mask (Chris)
References: 926abff21a8f ("drm/i915/cmdparser: Ignore Length operands during command matching")
Reported-by: Nicolai Stange <nstange@suse.de>
Cc: stable@vger.kernel.org # v5.4+
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200817195926.12671-1-mika.kuoppala@linux.intel.com
|
|
Add minimum width to planes, variable with specific formats for gen11+
to reflect recent bspec changes.
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200812210702.7153-1-matthew.s.atwood@intel.com
|
|
Major upgrade of HuC firmware with fixes and new features.
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200813200029.25307-2-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Fixes around DC5, DC6 and DC3CO in those new firmwares.
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200813200029.25307-1-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
From the 3 WAs for PSR2 man track/selective fetch this is only one
needed when doing single full frames at every flip.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200810174144.76761-2-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
All GEN12 platforms supports PSR2 selective fetch but not all GEN12
platforms supports PSR2 hardware tracking(aka RKL).
This feature consists in software programming registers with the
damaged area of each plane this way hardware will only fetch from
memory those areas and sent the PSR2 selective update blocks to panel,
saving even more power.
But as initial step it is only enabling the full frame fetch at
every flip, the actual selective fetch part will come in a future
patch.
Also this is only handling the page flip side, it is still completely
missing frontbuffer modifications, that is why the
enable_psr2_sel_fetch parameter was added.
v3:
- calling intel_psr2_sel_fetch_update() during the atomic check phase
(Ville)
BSpec: 55229
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200810174144.76761-1-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
We usually assume that increasing PCI device revision ID's translates to
newer steppings; macros like IS_KBL_REVID() that we use rely on this
behavior. Unfortunately this turns out to not be true on KBL; the
newer device 2 revision ID's sometimes go backward to older steppings.
The situation is further complicated by different GT and display
steppings associated with each revision ID.
Let's work around this by providing a table to map the revision ID to
specific GT and display steppings, and then perform our comparisons on
the mapped values.
v2:
- Move the kbl_revids[] array to intel_workarounds.c to avoid compiler
warnings about an unused variable in files that don't call the
macros (kernel test robot).
Bspec: 18329
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200811032105.2819370-1-matthew.d.roper@intel.com
Reviewed-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
This new HBR2 table for TGL-U and TGL-Y is required to pass
DisplayPort compliance.
BSpec: 49291
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Khaled Almahallawy<khaled.almahallawy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200807192629.64134-2-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
There is no way to differentiate TGL-U from TGL-Y by the PCI ids as
some ids are available in both SKUs.
So here using the root device id in the PCI bus that iGPU is in
to differentiate between U and Y.
BSpec: 44455
Reviewed-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200807192629.64134-1-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The command register is the PCODE MBOX low register not the high one as
described by the spec. This left the system with the TC-cold power state
being blocked all the time. Fix things by using the correct register.
Also to make sure we retry a request for at least 600usec, when the
PCODE MBOX command itself succeeded, but the TC-cold block command
failed, sleep for 1msec unconditionally after any fail.
The change was tested with JTAG register read of the HW/FW's actual
TC-cold state, which reported the expected states after this change.
Tested-by: Nivedita Swaminathan <nivedita.swaminathan@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200805150056.24248-1-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The dependency between power wells is determined by the ordering of the
power well list: when enabling the power wells for a domain, this
happens walking the power well list forward, while disabling them
happens in the reverse direction. Accordingly a power well on the list
must follow any other power well it depends on.
Since the TC AUX power wells depend on TC-cold being blocked, move the
TC-cold off power well before all AUX power wells.
Fixes: 3c02934b24e3 ("drm/i915/tc/tgl: Implement TC cold sequences")
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200720232952.16228-1-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
