summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2022-11-19iommu/vt-d: Set SRE bit only when hardware has SRS capTina Zhang1-2/+3
SRS cap is the hardware cap telling if the hardware IOMMU can support requests seeking supervisor privilege or not. SRE bit in scalable-mode PASID table entry is treated as Reserved(0) for implementation not supporting SRS cap. Checking SRS cap before setting SRE bit can avoid the non-recoverable fault of "Non-zero reserved field set in PASID Table Entry" caused by setting SRE bit while there is no SRS cap support. The fault messages look like below: DMAR: DRHD: handling fault status reg 2 DMAR: [DMA Read NO_PASID] Request device [00:0d.0] fault addr 0x1154e1000 [fault reason 0x5a] SM: Non-zero reserved field set in PASID Table Entry Fixes: 6f7db75e1c46 ("iommu/vt-d: Add second level page table interface") Cc: stable@vger.kernel.org Signed-off-by: Tina Zhang <tina.zhang@intel.com> Link: https://lore.kernel.org/r/20221115070346.1112273-1-tina.zhang@intel.com Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/20221116051544.26540-3-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-11-19iommu/vt-d: Preset Access bit for IOVA in FL non-leaf paging entriesTina Zhang1-5/+3
The A/D bits are preseted for IOVA over first level(FL) usage for both kernel DMA (i.e, domain typs is IOMMU_DOMAIN_DMA) and user space DMA usage (i.e., domain type is IOMMU_DOMAIN_UNMANAGED). Presetting A bit in FL requires to preset the bit in every related paging entries, including the non-leaf ones. Otherwise, hardware may treat this as an error. For example, in a case of ECAP_REG.SMPWC==0, DMA faults might occur with below DMAR fault messages (wrapped for line length) dumped. DMAR: DRHD: handling fault status reg 2 DMAR: [DMA Read NO_PASID] Request device [aa:00.0] fault addr 0x10c3a6000 [fault reason 0x90] SM: A/D bit update needed in first-level entry when set up in no snoop Fixes: 289b3b005cb9 ("iommu/vt-d: Preset A/D bits for user space DMA usage") Cc: stable@vger.kernel.org Signed-off-by: Tina Zhang <tina.zhang@intel.com> Link: https://lore.kernel.org/r/20221113010324.1094483-1-tina.zhang@intel.com Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/20221116051544.26540-2-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-11-19Merge tag 'input-for-v6.1-rc5' of ↵Linus Torvalds7-14/+37
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input fixes from Dmitry Torokhov: - a fix for 8042 to stop leaking platform device on unload - a fix for Goodix touchscreens on devices like Nanote UMPC-01 where we need to reset controller to load config from firmware - a workaround for Acer Switch to avoid interrupt storm from home and power buttons - a workaround for more ASUS ZenBook models to detect keyboard controller - a fix for iforce driver to properly handle communication errors - touchpad on HP Laptop 15-da3001TU switched to RMI mode * tag 'input-for-v6.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: i8042 - fix leaking of platform device on module removal Input: i8042 - apply probe defer to more ASUS ZenBook models Input: soc_button_array - add Acer Switch V 10 to dmi_use_low_level_irq[] Input: soc_button_array - add use_low_level_irq module parameter Input: iforce - invert valid length check when fetching device IDs Input: goodix - try resetting the controller when no config is set dt-bindings: input: touchscreen: Add compatible for Goodix GT7986U chip Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI mode
2022-11-19Merge tag 'zonefs-6.1-rc6' of ↵Linus Torvalds2-15/+27
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs Pull zonefs fixes from Damien Le Moal: - Fix the IO error recovery path for failures happening in the last zone of device, and that zone is a "runt" zone (smaller than the other zone). The current code was failing to properly obtain a zone report in that case. - Remove the unused to_attr() function as it is unused, causing compilation warnings with clang. * tag 'zonefs-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs: zonefs: Remove to_attr() helper function zonefs: fix zone report size in __zonefs_io_error()
2022-11-19Input: i8042 - fix leaking of platform device on module removalChen Jun1-4/+0
Avoid resetting the module-wide i8042_platform_device pointer in i8042_probe() or i8042_remove(), so that the device can be properly destroyed by i8042_exit() on module unload. Fixes: 9222ba68c3f4 ("Input: i8042 - add deferred probe support") Signed-off-by: Chen Jun <chenjun102@huawei.com> Link: https://lore.kernel.org/r/20221109034148.23821-1-chenjun102@huawei.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2022-11-19Merge tag 'io_uring-6.1-2022-11-18' of git://git.kernel.dk/linuxLinus Torvalds5-17/+27
Pull io_uring fixes from Jens Axboe: "This is mostly fixing issues around the poll rework, but also two tweaks for the multishot handling for accept and receive. All stable material" * tag 'io_uring-6.1-2022-11-18' of git://git.kernel.dk/linux: io_uring: disallow self-propelled ring polling io_uring: fix multishot recv request leaks io_uring: fix multishot accept request leaks io_uring: fix tw losing poll events io_uring: update res mask in io_poll_check_events
2022-11-19Merge tag 'arm64-fixes' of ↵Linus Torvalds2-3/+3
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fixes from Catalin Marinas: - Fix a build error with CONFIG_CFI_CLANG + CONFIG_FTRACE when CONFIG_FUNCTION_GRAPH_TRACER is not enabled. - Fix a BUG_ON triggered by the page table checker due to incorrect file_map_count for non-leaf pmd/pud (the arm64 pmd_user_accessible_page() not checking whether it's a leaf entry). * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64/mm: fix incorrect file_map_count for non-leaf pmd/pud arm64: ftrace: Define ftrace_stub_graph only with FUNCTION_GRAPH_TRACER
2022-11-19Merge tag 'block-6.1-2022-11-18' of git://git.kernel.dk/linuxLinus Torvalds11-16/+26
Pull block fixes from Jens Axboe: - NVMe pull request via Christoph: - Two more bogus nid quirks (Bean Huo, Tiago Dias Ferreira) - Memory leak fix in nvmet (Sagi Grimberg) - Regression fix for block cgroups pinning the wrong blkcg, causing leaks of cgroups and blkcgs (Chris) - UAF fix for drbd setup error handling (Dan) - Fix DMA alignment propagation in DM (Keith) * tag 'block-6.1-2022-11-18' of git://git.kernel.dk/linux: dm-log-writes: set dma_alignment limit in io_hints dm-integrity: set dma_alignment limit in io_hints block: make blk_set_default_limits() private dm-crypt: provide dma_alignment limit in io_hints block: make dma_alignment a stacking queue_limit nvmet: fix a memory leak in nvmet_auth_set_key nvme-pci: add NVME_QUIRK_BOGUS_NID for Netac NV7000 drbd: use after free in drbd_create_device() nvme-pci: add NVME_QUIRK_BOGUS_NID for Micron Nitro blk-cgroup: properly pin the parent in blkcg_css_online
2022-11-19Merge tag 'drm-fixes-2022-11-19' of git://anongit.freedesktop.org/drm/drmLinus Torvalds37-116/+310
Pull drm fixes from Dave Airlie: "I guess the main question is are things settling down, and I'd say kinda, these are all pretty small fixes, nothing big stands out really, just seems to be quite a few of them. Mostly amdgpu and core fixes, with some i915, tegra, vc4, panel bits. core: - Fix potential memory leak in drm_dev_init() - Fix potential null-ptr-deref in drm_vblank_destroy_worker() - Revert hiding unregistered connectors from userspace, as it breaks on DP-MST - Add workaround for DP++ dual mode adaptors that don't support i2c subaddressing i915: - Fix uaf with lmem_userfault_list handling amdgpu: - gang submit fixes - Fix a possible memory leak in ganng submit error path - DP tunneling fixes - DCN 3.1 page flip fix - DCN 3.2.x fixes - DCN 3.1.4 fixes - Don't expose degamma on hardware that doesn't support it - BACO fixes for SMU 11.x - BACO fixes for SMU 13.x - Virtual display fix for devices with no display hardware amdkfd: - Memory limit regression fix tegra: - tegra20 GART fix vc4: - Fix error handling in vc4_atomic_commit_tail() lima: - Set lima's clkname corrrectly when regulator is missing panel: - Set bpc for logictechno panels" * tag 'drm-fixes-2022-11-19' of git://anongit.freedesktop.org/drm/drm: (28 commits) gpu: host1x: Avoid trying to use GART on Tegra20 drm/display: Don't assume dual mode adaptors support i2c sub-addressing drm/amd/pm: fix SMU13 runpm hang due to unintentional workaround drm/amd/pm: enable runpm support over BACO for SMU13.0.7 drm/amd/pm: enable runpm support over BACO for SMU13.0.0 drm/amdgpu: there is no vbios fb on devices with no display hw (v2) drm/amdkfd: Fix a memory limit issue drm/amdgpu: disable BACO support on more cards drm/amd/display: don't enable DRM CRTC degamma property for DCE drm/amd/display: Set max for prefetch lines on dcn32 drm/amd/display: use uclk pstate latency for fw assisted mclk validation dcn32 drm/amd/display: Fix prefetch calculations for dcn32 drm/amd/display: Fix optc2_configure warning on dcn314 drm/amd/display: Fix calculation for cursor CAB allocation Revert "drm: hide unregistered connectors from GETCONNECTOR IOCTL" drm/amd/display: Support parsing VRAM info v3.0 from VBIOS drm/amd/display: Fix invalid DPIA AUX reply causing system hang drm/amdgpu: Add psp_13_0_10_ta firmware to modinfo drm/amd/display: Add HUBP surface flip interrupt handler drm/amd/display: Fix access timeout to DPIA AUX at boot time ...
2022-11-18drm/i915/dg2: Drop force_probe requirementMatt Roper1-1/+0
DG2 has been very usable for a while now, and all of the uapi changes related to fundamental platform usage have been finalized. Recent CI results have also been healthy, so we're ready to drop the force_probe requirement and enable the platform by default. Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221109001328.732000-1-matthew.d.roper@intel.com
2022-11-18Merge tag 's390-6.1-5' of ↵Linus Torvalds2-1/+11
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Alexander Gordeev: - Fix deadlock in discontiguous saved segments (DCSS) block device driver. When adding a disk and scanning partitions the scan would not break out early without a missed flag. - Avoid using global register variable for current_stack_pointer due to an old bug in gcc versions prior to gcc-8.4. Due to this bug a broken code is generated, which leads to stack corruptions. * tag 's390-6.1-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390: avoid using global register for current_stack_pointer s390/dcssblk: fix deadlock when adding a DCSS
2022-11-18Merge tag 'for-6.1/dm-fixes-2' of ↵Linus Torvalds3-8/+18
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm Pull device mapper fixes from Mike Snitzer: - Fix misbehavior if list_versions DM ioctl races with module loading - Fix missing decrement of no_sleep_enabled if dm_bufio_client_create failed - Allow DM integrity devices to be activated in read-only mode * tag 'for-6.1/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: dm integrity: clear the journal on suspend dm integrity: flush the journal on suspend dm bufio: Fix missing decrement of no_sleep_enabled if dm_bufio_client_create failed dm ioctl: fix misbehavior if list_versions races with module loading
2022-11-18Merge tag 'drm/tegra/for-6.1-rc6' of ↵Dave Airlie2-0/+8
https://gitlab.freedesktop.org/drm/tegra into drm-fixes drm/tegra: Fixes for v6.1-rc6 This contains a single fix that avoids using the GART on Tegra20 because it doesn't work well with the way the Tegra DRM driver tries to use it. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Thierry Reding <thierry.reding@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221118121614.3511110-1-thierry.reding@gmail.com
2022-11-18Merge tag 'usb-6.1-rc6' of ↵Linus Torvalds11-51/+90
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB driver fixes from Greg KH: "Here are a number of USB driver fixes and new device ids for 6.1-rc6. Included in here are: - new usb-serial device ids - dwc3 driver fixes for reported problems - cdns3 driver fixes - new USB device quirks - typec driver fixes - extcon USB typec driver fix All of these have been in linux-next with no reported issues" * tag 'usb-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: USB: serial: option: add u-blox LARA-L6 modem USB: serial: option: add u-blox LARA-R6 00B modem USB: serial: option: remove old LARA-R6 PID USB: serial: option: add Fibocom FM160 0x0111 composition usb: add NO_LPM quirk for Realforce 87U Keyboard usb: cdns3: host: fix endless superspeed hub port reset usb: chipidea: fix deadlock in ci_otg_del_timer usb: dwc3: Do not get extcon device when usb-role-switch is used usb: typec: tipd: Prevent uninitialized event{1,2} in IRQ handler usb: typec: mux: Enter safe mode only when pins need to be reconfigured extcon: usbc-tusb320: Call the Type-C IRQ handler only if a port is registered Revert "usb: dwc3: disable USB core PHY management" usb: dwc3: gadget: Return -ESHUTDOWN on ep disable USB: bcma: Make GPIO explicitly optional USB: serial: option: add Sierra Wireless EM9191
2022-11-18Merge tag 'staging-6.1-rc6' of ↵Linus Torvalds1-8/+1
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging driver fix from Greg KH: "Here is a single staging driver fix for 6.1-rc6. It resolves a bogus signed character test as pointed out, and fixed by, Jason in the rtl8192e driver It has been in linux-next for a few weeks now with no reported problems" * tag 'staging-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: rtl8192e: remove bogus ssid character sign test
2022-11-18arm64/mm: fix incorrect file_map_count for non-leaf pmd/pudLiu Shixin1-2/+2
The page table check trigger BUG_ON() unexpectedly when collapse hugepage: ------------[ cut here ]------------ kernel BUG at mm/page_table_check.c:82! Internal error: Oops - BUG: 00000000f2000800 [#1] SMP Dumping ftrace buffer: (ftrace buffer empty) Modules linked in: CPU: 6 PID: 68 Comm: khugepaged Not tainted 6.1.0-rc3+ #750 Hardware name: linux,dummy-virt (DT) pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : page_table_check_clear.isra.0+0x258/0x3f0 lr : page_table_check_clear.isra.0+0x240/0x3f0 [...] Call trace: page_table_check_clear.isra.0+0x258/0x3f0 __page_table_check_pmd_clear+0xbc/0x108 pmdp_collapse_flush+0xb0/0x160 collapse_huge_page+0xa08/0x1080 hpage_collapse_scan_pmd+0xf30/0x1590 khugepaged_scan_mm_slot.constprop.0+0x52c/0xac8 khugepaged+0x338/0x518 kthread+0x278/0x2f8 ret_from_fork+0x10/0x20 [...] Since pmd_user_accessible_page() doesn't check if a pmd is leaf, it decrease file_map_count for a non-leaf pmd comes from collapse_huge_page(). and so trigger BUG_ON() unexpectedly. Fix this problem by using pmd_leaf() insteal of pmd_present() in pmd_user_accessible_page(). Moreover, use pud_leaf() for pud_user_accessible_page() too. Fixes: 42b2547137f5 ("arm64/mm: enable ARCH_SUPPORTS_PAGE_TABLE_CHECK") Reported-by: Denys Vlasenko <dvlasenk@redhat.com> Signed-off-by: Liu Shixin <liushixin2@huawei.com> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: Pasha Tatashin <pasha.tatashin@soleen.com> Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com> Acked-by: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20221117075602.2904324-2-liushixin2@huawei.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2022-11-18Merge tag 'tty-6.1-rc6' of ↵Linus Torvalds7-91/+138
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver fixes from Greg KH: "Here are a number of small tty and serial driver fixes for 6.1-rc6. They all resolve reported problems: - kernel doc build problems with the -rc1 serial driver documentation update - n_gsm reported problems - imx serial driver missing callback - lots of tiny 8250 driver fixes for reported issues. All of these have been in linux-next for over a week with no reported problems" * tag 'tty-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: docs/driver-api/miscellaneous: Remove kernel-doc of serial_core.c serial: 8250: Flush DMA Rx on RLSI serial: 8250_lpss: Use 16B DMA burst with Elkhart Lake serial: 8250_lpss: Configure DMA also w/o DMA filter serial: 8250: Fall back to non-DMA Rx if IIR_RDI occurs tty: n_gsm: fix sleep-in-atomic-context bug in gsm_control_send Revert "tty: n_gsm: replace kicktimer with delayed_work" Revert "tty: n_gsm: avoid call of sleeping functions from atomic context" serial: imx: Add missing .thaw_noirq hook tty: serial: fsl_lpuart: don't break the on-going transfer when global reset serial: 8250: omap: Flush PM QOS work on remove serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove() serial: 8250_omap: remove wait loop from Errata i202 workaround serial: 8250: omap: Fix missing PM runtime calls for omap8250_set_mctrl() serial: 8250: 8250_omap: Avoid RS485 RTS glitch on ->set_termios()
2022-11-18Merge tag 'driver-core-6.1-rc6' of ↵Linus Torvalds1-2/+12
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core fixes from Greg KH: "Here are two small driver core fixes for 6.1-rc6: - utsname fix, this one should already be in your tree as it came from a different tree earlier. - kernfs bugfix for a much reported syzbot report that seems to keep getting triggered. Both of these have been in linux-next for a while with no reported issues" * tag 'driver-core-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: kernfs: Fix spurious lockdep warning in kernfs_find_and_get_node_by_id() kernel/utsname_sysctl.c: Add missing enum uts_proc value
2022-11-18Merge tag 'char-misc-6.1-rc6' of ↵Linus Torvalds22-75/+111
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver fixes from Greg KH: "Here are some small char/misc and other driver fixes for 6.1-rc6 to resolve some reported problems. Included in here are: - iio driver fixes - binder driver fix - nvmem driver fix - vme_vmci information leak fix - parport fix - slimbus configuration fix - coreboot firmware bugfix - speakup build fix and crash fix All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (22 commits) firmware: coreboot: Register bus in module init nvmem: u-boot-env: fix crc32_data_offset on redundant u-boot-env slimbus: qcom-ngd: Fix build error when CONFIG_SLIM_QCOM_NGD_CTRL=y && CONFIG_QCOM_RPROC_COMMON=m docs: update mediator contact information in CoC doc slimbus: stream: correct presence rate frequencies nvmem: lan9662-otp: Fix compatible string binder: validate alloc->mm in ->mmap() handler parport_pc: Avoid FIFO port location truncation siox: fix possible memory leak in siox_device_add() misc/vmw_vmci: fix an infoleak in vmci_host_do_receive_datagram() speakup: replace utils' u_char with unsigned char speakup: fix a segfault caused by switching consoles tools: iio: iio_generic_buffer: Fix read size iio: imu: bno055: uninitialized variable bug in bno055_trigger_handler() iio: adc: at91_adc: fix possible memory leak in at91_adc_allocate_trigger() iio: adc: mp2629: fix potential array out of bound access iio: adc: mp2629: fix wrong comparison of channel iio: pressure: ms5611: changed hardcoded SPI speed to value limited iio: pressure: ms5611: fixed value compensation bug iio: accel: bma400: Ensure VDDIO is enable defore reading the chip ID. ...
2022-11-18drm/i915/mtl: Skip doubling channel numbers for LPDDR4/LPDDDR5Radhakrishna Sripada1-1/+2
MTL LPDDR5 reported 16b with 8 channels. Previous platforms reported 32b with 4 channels and hence needed a multiplication by a factor of 2. Skip increasing the channels for MTL. v2: Use version check instead of platform check(MattR) Bspec: 64631 Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221117213015.584417-2-radhakrishna.sripada@intel.com
2022-11-18drm/i915/mtl: Fix dram info readoutRadhakrishna Sripada1-2/+1
MEM_SS_INFO_GLOBAL Register info read from the hardware is cached in val. However the variable is being modified when determining the DRAM type thereby clearing out the channels and qgv info extracted later in the function xelpdp_get_dram_info. Preserve the register value and use extracted fields in the switch statement. Fixes: 825477e77912 ("drm/i915/mtl: Obtain SAGV values from MMIO instead of GT pcode mailbox") Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221117213015.584417-1-radhakrishna.sripada@intel.com
2022-11-18Merge tag 'sound-6.1-rc6' of ↵Linus Torvalds26-98/+176
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound fixes from Takashi Iwai: "A fair amount of commits at this time due to ASoC PR merge, but all look small and easy, mostly device-specific fixes spanned in various drivers. Hopefully this should be the last big chunk for 6.1" * tag 'sound-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits) ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book Pro 360 ALSA: hda/realtek: fix speakers for Samsung Galaxy Book Pro ALSA: usb-audio: Drop snd_BUG_ON() from snd_usbmidi_output_open() ASoC: stm32: dfsdm: manage cb buffers cleanup ASoC: sof_es8336: reduce pop noise on speaker ASoC: SOF: topology: No need to assign core ID if token parsing failed ASoC: soc-utils: Remove __exit for snd_soc_util_exit() ASoC: rt5677: fix legacy dai naming ASoC: rt5514: fix legacy dai naming ASoC: SOF: ipc3-topology: use old pipeline teardown flow with SOF2.1 and older ASoC: hda: intel-dsp-config: add ES83x6 quirk for IceLake ASoC: Intel: soc-acpi: add ES83x6 support to IceLake ASoC: tas2780: Fix set_tdm_slot in case of single slot ASoC: tas2764: Fix set_tdm_slot in case of single slot ASoC: tas2770: Fix set_tdm_slot in case of single slot ASoC: fsl_asrc fsl_esai fsl_sai: allow CONFIG_PM=N ASoC: core: Fix use-after-free in snd_soc_exit() MAINTAINERS: update Tzung-Bi's email address ASoC: Intel: bytcht_es8316: Add quirk for the Nanote UMPC-01 ASoC: amd: yc: Add Alienware m17 R5 AMD into DMI table ...
2022-11-18Merge tag 'mmc-v6.1-rc5' of ↵Linus Torvalds3-1/+16
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc Pull MMC fixes from Ulf Hansson: "MMC core: - Fixup VDD/VMMC voltage-range negotiation MMC host: - sdhci-pci: Fix memory leak by adding a missing pci_dev_put() - sdhci-pci-o2micro: Fix card detect by tuning the debounce timeout" * tag 'mmc-v6.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: mmc: sdhci-pci: Fix possible memory leak caused by missing pci_dev_put() mmc: sdhci-pci-o2micro: fix card detect fail issue caused by CD# debounce timeout mmc: core: properly select voltage range without power cycle
2022-11-18drm/i915/rpl-p: Add stepping infoMatt Atwood1-0/+7
Add stepping-substepping info in accordance to bpsec changes. Bspec: 55376 Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221117214132.152061-1-matthew.s.atwood@intel.com
2022-11-18io_uring: disallow self-propelled ring pollingPavel Begunkov1-0/+2
When we post a CQE we wake all ring pollers as it normally should be. However, if a CQE was generated by a multishot poll request targeting its own ring, it'll wake that request up, which will make it to post a new CQE, which will wake the request and so on until it exhausts all CQ entries. Don't allow multishot polling io_uring files but downgrade them to oneshots, which was always stated as a correct behaviour that the userspace should check for. Cc: stable@vger.kernel.org Fixes: aa43477b04025 ("io_uring: poll rework") Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Link: https://lore.kernel.org/r/3124038c0e7474d427538c2d915335ec28c92d21.1668785722.git.asml.silence@gmail.com Signed-off-by: Jens Axboe <axboe@kernel.dk>
2022-11-18dm integrity: clear the journal on suspendMikulas Patocka1-0/+13
There was a problem that a user burned a dm-integrity image on CDROM and could not activate it because it had a non-empty journal. Fix this problem by flushing the journal (done by the previous commit) and clearing the journal (done by this commit). Once the journal is cleared, dm-integrity won't attempt to replay it on the next activation. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
2022-11-18dm integrity: flush the journal on suspendMikulas Patocka1-6/+1
This commit flushes the journal on suspend. It is prerequisite for the next commit that enables activating dm integrity devices in read-only mode. Note that we deliberately didn't flush the journal on suspend, so that the journal replay code would be tested. However, the dm-integrity code is 5 years old now, so that journal replay is well-tested, and we can make this change now. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
2022-11-18drm/i915/mtl+: Don't enable the AUX_IO power for non-eDP port main linksImre Deak1-2/+3
MTL+ requires the AUX_IO power for the main link only on eDP, so don't enable it in other cases. v2: - Rebased on checking intel_encoder_can_psr() instead of crtc->has_psr. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-10-imre.deak@intel.com
2022-11-18drm/i915: Factor out function to get/put AUX_IO power for main linkImre Deak1-33/+52
Factor out functions to get/put the AUX_IO power domain for the main link on DDI ports. While at it clarify the corresponding code comment. No functional change. v2: - s/(get/put)_aux_power_for_main_link/main_link_aux_power_domain_(get/put) (Jani) - Clarify in the code comment that AUX_IO is needed only by TypeC besides eDP/PSR. v3: - Rebased on checking intel_encoder_can_psr() instead of crtc->has_psr. v4: - Don't call fetch_and_zero() with side-effect during variable declaration. (Ville) Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-9-imre.deak@intel.com
2022-11-18drm/i915: Add missing DC_OFF power domain->well mappingsImre Deak1-0/+8
Add the missing DC_OFF power domain -> DC_OFF power well mappings on all platforms. This didn't cause a problem as the DC_OFF power domain is only used on JSL, where the mapping was already correct. Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-8-imre.deak@intel.com
2022-11-18drm/i915: Add missing AUX_IO_A power domain->well mappingsImre Deak1-0/+2
BXT and GLK were missing the AUX_IO_A power domain -> PHY A common power well mapping, add these now. This didn't cause a problem as the AUX_IO_A and DDI_LANES_A power domains are acquired together. Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-7-imre.deak@intel.com
2022-11-18drm/i915/tgl+: Enable display DC power states on all eDP portsImre Deak4-7/+89
Starting with TGL eDP is supported on ports B+ (besides port A), so make sure DC states are not blocked on any such ports. For this add an AUX_IO_<port> power domain for each port with eDP support. These domains similarly to AUX_IO_A enable only the AUX_IO_<port> power well for an enabled port, whereas the existing AUX_<port> domains enable both the AUX_IO_<port> and the DC_OFF power wells as required by DP AUX transfers. v2: (Ville) - Split the change using AUX vs. AUX_IO on port A to a separate patch. - Select AUX_IO vs. AUX based on crtc_state->has_psr instead of is_edp(). v3: - Rebased on checking intel_encoder_can_psr() instead of crtc->has_psr. v4: - Fix warn in intel_display_power_aux_io_domain(). (Ville) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-6-imre.deak@intel.com
2022-11-18drm/i915: Use the AUX_IO power domain only for eDP/PSR portImre Deak1-2/+4
Use the AUX_IO_A display power domain only for eDP on port A where PSR is also supported. This is the case where DC states need to be enabled while the output is enabled - ensured by AUX_IO_A domain not enabling the DC_OFF power well. Otherwise port A can be treated the same way as other ports with an external DP output: using the AUX_<port> domain which disables the unrequired DC states. This change prepares for the next patch enabling DC states on all ports supporting eDP/PSR besides port A. v2: - Check the encoder PSR capability instead of PSR being enabled in the crtc_state, as the latter can be changed with a fastset. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-5-imre.deak@intel.com
2022-11-18drm/i915: Move the POWER_DOMAIN_AUX_IO_A definition to its logical placeImre Deak3-7/+8
Move the definition of the AUX_IO_A power domain, requiring only the corresponding AUX_IO_A power well to be enabled, before all the AUX_<port> power domains, which require both the AUX_IO_<port> and the DC_OFF power wells to be enabled. No functional change. Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-4-imre.deak@intel.com
2022-11-18drm/i915: Preallocate the debug power domain wakerefs arrayImre Deak2-6/+6
Since the current size of intel_display_power_domain_set struct is close to 1kB, it's better to use preallocated memory for it. The only user of the intel_display_power_get/put_in_set() allocating the struct on stack is hsw_get_pipe_config(), so we can avoid potential stack overallocations by moving the struct here to the preallocated intel_crtc struct (hsw_get_pipe_config() is non-reentrant wrt. each CRTC). This patch replaces https://lore.kernel.org/intel-gfx/20221107170917.3566758-5-imre.deak@intel.com/T/#md3f6cdf17fcd Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-3-imre.deak@intel.com
2022-11-18drm/i915: Fix warn in intel_display_power_*_domain() functionsImre Deak1-4/+4
The intel_display_power_*_domain() functions should always warn if a default domain is returned as a fallback, fix this up. Spotted by Ville. Fixes: 979e1b32e0e2 ("drm/i915: Sanitize the port -> DDI/AUX power domain mapping for each platform") Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jouni Högander <jouni.hogander@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-2-imre.deak@intel.com
2022-11-18dm bufio: Fix missing decrement of no_sleep_enabled if ↵Zhihao Cheng1-0/+2
dm_bufio_client_create failed The 'no_sleep_enabled' should be decreased in error handling path in dm_bufio_client_create() when the DM_BUFIO_CLIENT_NO_SLEEP flag is set, otherwise static_branch_unlikely() will always return true even if no dm_bufio_client instances have DM_BUFIO_CLIENT_NO_SLEEP flag set. Cc: stable@vger.kernel.org Fixes: 3c1c875d0586 ("dm bufio: conditionally enable branching for DM_BUFIO_CLIENT_NO_SLEEP") Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
2022-11-18dm ioctl: fix misbehavior if list_versions races with module loadingMikulas Patocka1-2/+2
__list_versions will first estimate the required space using the "dm_target_iterate(list_version_get_needed, &needed)" call and then will fill the space using the "dm_target_iterate(list_version_get_info, &iter_info)" call. Each of these calls locks the targets using the "down_read(&_lock)" and "up_read(&_lock)" calls, however between the first and second "dm_target_iterate" there is no lock held and the target modules can be loaded at this point, so the second "dm_target_iterate" call may need more space than what was the first "dm_target_iterate" returned. The code tries to handle this overflow (see the beginning of list_version_get_info), however this handling is incorrect. The code sets "param->data_size = param->data_start + needed" and "iter_info.end = (char *)vers+len" - "needed" is the size returned by the first dm_target_iterate call; "len" is the size of the buffer allocated by userspace. "len" may be greater than "needed"; in this case, the code will write up to "len" bytes into the buffer, however param->data_size is set to "needed", so it may write data past the param->data_size value. The ioctl interface copies only up to param->data_size into userspace, thus part of the result will be truncated. Fix this bug by setting "iter_info.end = (char *)vers + needed;" - this guarantees that the second "dm_target_iterate" call will write only up to the "needed" buffer and it will exit with "DM_BUFFER_FULL_FLAG" if it overflows the "needed" space - in this case, userspace will allocate a larger buffer and retry. Note that there is also a bug in list_version_get_needed - we need to add "strlen(tt->name) + 1" to the needed size, not "strlen(tt->name)". Cc: stable@vger.kernel.org Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
2022-11-18Merge tag 'nvme-6.1-2022-11-18' of git://git.infradead.org/nvme into block-6.1Jens Axboe2-0/+6
Pull NVMe fixes from Christoph: "nvme fixes for Linux 6.1 - two more bogus nid quirks (Bean Huo, Tiago Dias Ferreira) - memory leak fix in nvmet (Sagi Grimberg)" * tag 'nvme-6.1-2022-11-18' of git://git.infradead.org/nvme: nvmet: fix a memory leak in nvmet_auth_set_key nvme-pci: add NVME_QUIRK_BOGUS_NID for Netac NV7000 nvme-pci: add NVME_QUIRK_BOGUS_NID for Micron Nitro
2022-11-18udmabuf: add vmap and vunmap methods to udmabuf_opsLukasz Wiecaszek1-0/+28
The reason behind that patch is associated with videobuf2 subsystem (or more genrally with v4l2 framework) and user created dma buffers (udmabuf). In some circumstances when dealing with V4L2_MEMORY_DMABUF buffers videobuf2 subsystem wants to use dma_buf_vmap() method on the attached dma buffer. As udmabuf does not have .vmap operation implemented, such dma_buf_vmap() natually fails. videobuf2_common: __vb2_queue_alloc: allocated 3 buffers, 1 plane(s) each videobuf2_common: __prepare_dmabuf: buffer for plane 0 changed videobuf2_common: __prepare_dmabuf: failed to map dmabuf for plane 0 videobuf2_common: __buf_prepare: buffer preparation failed: -14 The patch itself seems to be strighforward. It adds implementation of .vmap and .vunmap methods to 'struct dma_buf_ops udmabuf_ops'. .vmap method itself uses vm_map_ram() to map pages linearly into the kernel virtual address space. .vunmap removes mapping created earlier by .vmap. All locking and 'vmapping counting' is done in dma_buf.c so it seems to be redundant/unnecessary in .vmap/.vunmap. Signed-off-by: Lukasz Wiecaszek <lukasz.wiecaszek@gmail.com> Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Acked-by: Christian König <christian.koenig@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221117171810.75637-1-lukasz.wiecaszek@gmail.com Signed-off-by: Christian König <christian.koenig@amd.com>
2022-11-18gpu: host1x: Avoid trying to use GART on Tegra20Robin Murphy2-0/+8
Since commit c7e3ca515e78 ("iommu/tegra: gart: Do not register with bus") quite some time ago, the GART driver has effectively disabled itself to avoid issues with the GPU driver expecting it to work in ways that it doesn't. As of commit 57365a04c921 ("iommu: Move bus setup to IOMMU device registration") that bodge no longer works, but really the GPU driver should be responsible for its own behaviour anyway. Make the workaround explicit. Reported-by: Jon Hunter <jonathanh@nvidia.com> Suggested-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Robin Murphy <robin.murphy@arm.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2022-11-18tracing: Fix potential null-pointer-access of entry in list 'tr->err_log'Zheng Yejian1-4/+5
Entries in list 'tr->err_log' will be reused after entry number exceed TRACING_LOG_ERRS_MAX. The cmd string of the to be reused entry will be freed first then allocated a new one. If the allocation failed, then the entry will still be in list 'tr->err_log' but its 'cmd' field is set to be NULL, later access of 'cmd' is risky. Currently above problem can cause the loss of 'cmd' information of first entry in 'tr->err_log'. When execute `cat /sys/kernel/tracing/error_log`, reproduce logs like: [ 37.495100] trace_kprobe: error: Maxactive is not for kprobe(null) ^ [ 38.412517] trace_kprobe: error: Maxactive is not for kprobe Command: p4:myprobe2 do_sys_openat2 ^ Link: https://lore.kernel.org/linux-trace-kernel/20221114104632.3547266-1-zhengyejian1@huawei.com Fixes: 1581a884b7ca ("tracing: Remove size restriction on tracing_log_err cmd strings") Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2022-11-18tracing: Remove unused __bad_type_size() methodQiujun Huang1-2/+0
__bad_type_size() is unused after commit 04ae87a52074("ftrace: Rework event_create_dir()"). So, remove it. Link: https://lkml.kernel.org/r/D062EC2E-7DB7-4402-A67E-33C3577F551E@gmail.com Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Qiujun Huang <hqjagain@gmail.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2022-11-18tracing/eprobe: Fix eprobe filter to make a filter correctlyMasami Hiramatsu (Google)1-1/+1
Since the eprobe filter was defined based on the eprobe's trace event itself, it doesn't work correctly. Use the original trace event of the eprobe when making the filter so that the filter works correctly. Without this fix: # echo 'e syscalls/sys_enter_openat \ flags_rename=$flags:u32 if flags < 1000' >> dynamic_events # echo 1 > events/eprobes/sys_enter_openat/enable [ 114.551550] event trace: Could not enable event sys_enter_openat -bash: echo: write error: Invalid argument With this fix: # echo 'e syscalls/sys_enter_openat \ flags_rename=$flags:u32 if flags < 1000' >> dynamic_events # echo 1 > events/eprobes/sys_enter_openat/enable # tail trace cat-241 [000] ...1. 266.498449: sys_enter_openat: (syscalls.sys_enter_openat) flags_rename=0 cat-242 [000] ...1. 266.977640: sys_enter_openat: (syscalls.sys_enter_openat) flags_rename=0 Link: https://lore.kernel.org/all/166823166395.1385292.8931770640212414483.stgit@devnote3/ Fixes: 752be5c5c910 ("tracing/eprobe: Add eprobe filter support") Reported-by: Rafael Mendonca <rafaelmendsr@gmail.com> Tested-by: Rafael Mendonca <rafaelmendsr@gmail.com> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2022-11-18tracing/eprobe: Fix warning in filter creationRafael Mendonca1-1/+1
The filter pointer (filterp) passed to create_filter() function must be a pointer that references a NULL pointer, otherwise, we get a warning when adding a filter option to the event probe: root@localhost:/sys/kernel/tracing# echo 'e:egroup/stat_runtime_4core sched/sched_stat_runtime \ runtime=$runtime:u32 if cpu < 4' >> dynamic_events [ 5034.340439] ------------[ cut here ]------------ [ 5034.341258] WARNING: CPU: 0 PID: 223 at kernel/trace/trace_events_filter.c:1939 create_filter+0x1db/0x250 [...] stripped [ 5034.345518] RIP: 0010:create_filter+0x1db/0x250 [...] stripped [ 5034.351604] Call Trace: [ 5034.351803] <TASK> [ 5034.351959] ? process_preds+0x1b40/0x1b40 [ 5034.352241] ? rcu_read_lock_bh_held+0xd0/0xd0 [ 5034.352604] ? kasan_set_track+0x29/0x40 [ 5034.352904] ? kasan_save_alloc_info+0x1f/0x30 [ 5034.353264] create_event_filter+0x38/0x50 [ 5034.353573] __trace_eprobe_create+0x16f4/0x1d20 [ 5034.353964] ? eprobe_dyn_event_release+0x360/0x360 [ 5034.354363] ? mark_held_locks+0xa6/0xf0 [ 5034.354684] ? _raw_spin_unlock_irqrestore+0x35/0x60 [ 5034.355105] ? trace_hardirqs_on+0x41/0x120 [ 5034.355417] ? _raw_spin_unlock_irqrestore+0x35/0x60 [ 5034.355751] ? __create_object+0x5b7/0xcf0 [ 5034.356027] ? lock_is_held_type+0xaf/0x120 [ 5034.356362] ? rcu_read_lock_bh_held+0xb0/0xd0 [ 5034.356716] ? rcu_read_lock_bh_held+0xd0/0xd0 [ 5034.357084] ? kasan_set_track+0x29/0x40 [ 5034.357411] ? kasan_save_alloc_info+0x1f/0x30 [ 5034.357715] ? __kasan_kmalloc+0xb8/0xc0 [ 5034.357985] ? write_comp_data+0x2f/0x90 [ 5034.358302] ? __sanitizer_cov_trace_pc+0x25/0x60 [ 5034.358691] ? argv_split+0x381/0x460 [ 5034.358949] ? write_comp_data+0x2f/0x90 [ 5034.359240] ? eprobe_dyn_event_release+0x360/0x360 [ 5034.359620] trace_probe_create+0xf6/0x110 [ 5034.359940] ? trace_probe_match_command_args+0x240/0x240 [ 5034.360376] eprobe_dyn_event_create+0x21/0x30 [ 5034.360709] create_dyn_event+0xf3/0x1a0 [ 5034.360983] trace_parse_run_command+0x1a9/0x2e0 [ 5034.361297] ? dyn_event_release+0x500/0x500 [ 5034.361591] dyn_event_write+0x39/0x50 [ 5034.361851] vfs_write+0x311/0xe50 [ 5034.362091] ? dyn_event_seq_next+0x40/0x40 [ 5034.362376] ? kernel_write+0x5b0/0x5b0 [ 5034.362637] ? write_comp_data+0x2f/0x90 [ 5034.362937] ? __sanitizer_cov_trace_pc+0x25/0x60 [ 5034.363258] ? ftrace_syscall_enter+0x544/0x840 [ 5034.363563] ? write_comp_data+0x2f/0x90 [ 5034.363837] ? __sanitizer_cov_trace_pc+0x25/0x60 [ 5034.364156] ? write_comp_data+0x2f/0x90 [ 5034.364468] ? write_comp_data+0x2f/0x90 [ 5034.364770] ksys_write+0x158/0x2a0 [ 5034.365022] ? __ia32_sys_read+0xc0/0xc0 [ 5034.365344] __x64_sys_write+0x7c/0xc0 [ 5034.365669] ? syscall_enter_from_user_mode+0x53/0x70 [ 5034.366084] do_syscall_64+0x60/0x90 [ 5034.366356] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 5034.366767] RIP: 0033:0x7ff0b43938f3 [...] stripped [ 5034.371892] </TASK> [ 5034.374720] ---[ end trace 0000000000000000 ]--- Link: https://lore.kernel.org/all/20221108202148.1020111-1-rafaelmendsr@gmail.com/ Fixes: 752be5c5c910 ("tracing/eprobe: Add eprobe filter support") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2022-11-18kprobes: Skip clearing aggrprobe's post_handler in kprobe-on-ftrace caseLi Huafei1-1/+7
In __unregister_kprobe_top(), if the currently unregistered probe has post_handler but other child probes of the aggrprobe do not have post_handler, the post_handler of the aggrprobe is cleared. If this is a ftrace-based probe, there is a problem. In later calls to disarm_kprobe(), we will use kprobe_ftrace_ops because post_handler is NULL. But we're armed with kprobe_ipmodify_ops. This triggers a WARN in __disarm_kprobe_ftrace() and may even cause use-after-free: Failed to disarm kprobe-ftrace at kernel_clone+0x0/0x3c0 (error -2) WARNING: CPU: 5 PID: 137 at kernel/kprobes.c:1135 __disarm_kprobe_ftrace.isra.21+0xcf/0xe0 Modules linked in: testKprobe_007(-) CPU: 5 PID: 137 Comm: rmmod Not tainted 6.1.0-rc4-dirty #18 [...] Call Trace: <TASK> __disable_kprobe+0xcd/0xe0 __unregister_kprobe_top+0x12/0x150 ? mutex_lock+0xe/0x30 unregister_kprobes.part.23+0x31/0xa0 unregister_kprobe+0x32/0x40 __x64_sys_delete_module+0x15e/0x260 ? do_user_addr_fault+0x2cd/0x6b0 do_syscall_64+0x3a/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd [...] For the kprobe-on-ftrace case, we keep the post_handler setting to identify this aggrprobe armed with kprobe_ipmodify_ops. This way we can disarm it correctly. Link: https://lore.kernel.org/all/20221112070000.35299-1-lihuafei1@huawei.com/ Fixes: 0bc11ed5ab60 ("kprobes: Allow kprobes coexist with livepatch") Reported-by: Zhao Gongyi <zhaogongyi@huawei.com> Suggested-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Li Huafei <lihuafei1@huawei.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2022-11-18rethook: fix a potential memleak in rethook_alloc()Yi Yang1-1/+3
In rethook_alloc(), the variable rh is not freed or passed out if handler is NULL, which could lead to a memleak, fix it. Link: https://lore.kernel.org/all/20221110104438.88099-1-yiyang13@huawei.com/ [Masami: Add "rethook:" tag to the title.] Fixes: 54ecbe6f1ed5 ("rethook: Add a generic return hook") Cc: stable@vger.kernel.org Signed-off-by: Yi Yang <yiyang13@huawei.com> Acke-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2022-11-18tracing/eprobe: Fix memory leak of filter stringRafael Mendonca1-0/+1
The filter string doesn't get freed when a dynamic event is deleted. If a filter is set, then memory is leaked: root@localhost:/sys/kernel/tracing# echo 'e:egroup/stat_runtime_4core \ sched/sched_stat_runtime runtime=$runtime:u32 if cpu < 4' >> dynamic_events root@localhost:/sys/kernel/tracing# echo "-:egroup/stat_runtime_4core" >> dynamic_events root@localhost:/sys/kernel/tracing# echo scan > /sys/kernel/debug/kmemleak [ 224.416373] kmemleak: 1 new suspected memory leaks (see /sys/kernel/debug/kmemleak) root@localhost:/sys/kernel/tracing# cat /sys/kernel/debug/kmemleak unreferenced object 0xffff88810156f1b8 (size 8): comm "bash", pid 224, jiffies 4294935612 (age 55.800s) hex dump (first 8 bytes): 63 70 75 20 3c 20 34 00 cpu < 4. backtrace: [<000000009f880725>] __kmem_cache_alloc_node+0x18e/0x720 [<0000000042492946>] __kmalloc+0x57/0x240 [<0000000034ea7995>] __trace_eprobe_create+0x1214/0x1d30 [<00000000d70ef730>] trace_probe_create+0xf6/0x110 [<00000000915c7b16>] eprobe_dyn_event_create+0x21/0x30 [<000000000d894386>] create_dyn_event+0xf3/0x1a0 [<00000000e9af57d5>] trace_parse_run_command+0x1a9/0x2e0 [<0000000080777f18>] dyn_event_write+0x39/0x50 [<0000000089f0ec73>] vfs_write+0x311/0xe50 [<000000003da1bdda>] ksys_write+0x158/0x2a0 [<00000000bb1e616e>] __x64_sys_write+0x7c/0xc0 [<00000000e8aef1f7>] do_syscall_64+0x60/0x90 [<00000000fe7fe8ba>] entry_SYSCALL_64_after_hwframe+0x63/0xcd Additionally, in __trace_eprobe_create() function, if an error occurs after the call to trace_eprobe_parse_filter(), which allocates the filter string, then memory is also leaked. That can be reproduced by creating the same event probe twice: root@localhost:/sys/kernel/tracing# echo 'e:egroup/stat_runtime_4core \ sched/sched_stat_runtime runtime=$runtime:u32 if cpu < 4' >> dynamic_events root@localhost:/sys/kernel/tracing# echo 'e:egroup/stat_runtime_4core \ sched/sched_stat_runtime runtime=$runtime:u32 if cpu < 4' >> dynamic_events -bash: echo: write error: File exists root@localhost:/sys/kernel/tracing# echo scan > /sys/kernel/debug/kmemleak [ 207.871584] kmemleak: 1 new suspected memory leaks (see /sys/kernel/debug/kmemleak) root@localhost:/sys/kernel/tracing# cat /sys/kernel/debug/kmemleak unreferenced object 0xffff8881020d17a8 (size 8): comm "bash", pid 223, jiffies 4294938308 (age 31.000s) hex dump (first 8 bytes): 63 70 75 20 3c 20 34 00 cpu < 4. backtrace: [<000000000e4f5f31>] __kmem_cache_alloc_node+0x18e/0x720 [<0000000024f0534b>] __kmalloc+0x57/0x240 [<000000002930a28e>] __trace_eprobe_create+0x1214/0x1d30 [<0000000028387903>] trace_probe_create+0xf6/0x110 [<00000000a80d6a9f>] eprobe_dyn_event_create+0x21/0x30 [<000000007168698c>] create_dyn_event+0xf3/0x1a0 [<00000000f036bf6a>] trace_parse_run_command+0x1a9/0x2e0 [<00000000014bde8b>] dyn_event_write+0x39/0x50 [<0000000078a097f7>] vfs_write+0x311/0xe50 [<00000000996cb208>] ksys_write+0x158/0x2a0 [<00000000a3c2acb0>] __x64_sys_write+0x7c/0xc0 [<0000000006b5d698>] do_syscall_64+0x60/0x90 [<00000000780e8ecf>] entry_SYSCALL_64_after_hwframe+0x63/0xcd Fix both issues by releasing the filter string in trace_event_probe_cleanup(). Link: https://lore.kernel.org/all/20221108235738.1021467-1-rafaelmendsr@gmail.com/ Fixes: 752be5c5c910 ("tracing/eprobe: Add eprobe filter support") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2022-11-18tracing: kprobe: Fix potential null-ptr-deref on trace_array in ↵Shang XiaoJing1-0/+4
kprobe_event_gen_test_exit() When test_gen_kprobe_cmd() failed after kprobe_event_gen_cmd_end(), it will goto delete, which will call kprobe_event_delete() and release the corresponding resource. However, the trace_array in gen_kretprobe_test will point to the invalid resource. Set gen_kretprobe_test to NULL after called kprobe_event_delete() to prevent null-ptr-deref. BUG: kernel NULL pointer dereference, address: 0000000000000070 PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 0 PID: 246 Comm: modprobe Tainted: G W 6.1.0-rc1-00174-g9522dc5c87da-dirty #248 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014 RIP: 0010:__ftrace_set_clr_event_nolock+0x53/0x1b0 Code: e8 82 26 fc ff 49 8b 1e c7 44 24 0c ea ff ff ff 49 39 de 0f 84 3c 01 00 00 c7 44 24 18 00 00 00 00 e8 61 26 fc ff 48 8b 6b 10 <44> 8b 65 70 4c 8b 6d 18 41 f7 c4 00 02 00 00 75 2f RSP: 0018:ffffc9000159fe00 EFLAGS: 00010293 RAX: 0000000000000000 RBX: ffff88810971d268 RCX: 0000000000000000 RDX: ffff8881080be600 RSI: ffffffff811b48ff RDI: ffff88810971d058 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000001 R10: ffffc9000159fe58 R11: 0000000000000001 R12: ffffffffa0001064 R13: ffffffffa000106c R14: ffff88810971d238 R15: 0000000000000000 FS: 00007f89eeff6540(0000) GS:ffff88813b600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000070 CR3: 000000010599e004 CR4: 0000000000330ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __ftrace_set_clr_event+0x3e/0x60 trace_array_set_clr_event+0x35/0x50 ? 0xffffffffa0000000 kprobe_event_gen_test_exit+0xcd/0x10b [kprobe_event_gen_test] __x64_sys_delete_module+0x206/0x380 ? lockdep_hardirqs_on_prepare+0xd8/0x190 ? syscall_enter_from_user_mode+0x1c/0x50 do_syscall_64+0x3f/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7f89eeb061b7 Link: https://lore.kernel.org/all/20221108015130.28326-3-shangxiaojing@huawei.com/ Fixes: 64836248dda2 ("tracing: Add kprobe event command generation test module") Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com> Cc: stable@vger.kernel.org Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2022-11-18tracing: kprobe: Fix potential null-ptr-deref on trace_event_file in ↵Shang XiaoJing1-16/+28
kprobe_event_gen_test_exit() When trace_get_event_file() failed, gen_kretprobe_test will be assigned as the error code. If module kprobe_event_gen_test is removed now, the null pointer dereference will happen in kprobe_event_gen_test_exit(). Check if gen_kprobe_test or gen_kretprobe_test is error code or NULL before dereference them. BUG: kernel NULL pointer dereference, address: 0000000000000012 PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 3 PID: 2210 Comm: modprobe Not tainted 6.1.0-rc1-00171-g2159299a3b74-dirty #217 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014 RIP: 0010:kprobe_event_gen_test_exit+0x1c/0xb5 [kprobe_event_gen_test] Code: Unable to access opcode bytes at 0xffffffff9ffffff2. RSP: 0018:ffffc900015bfeb8 EFLAGS: 00010246 RAX: ffffffffffffffea RBX: ffffffffa0002080 RCX: 0000000000000000 RDX: ffffffffa0001054 RSI: ffffffffa0001064 RDI: ffffffffdfc6349c RBP: ffffffffa0000000 R08: 0000000000000004 R09: 00000000001e95c0 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000800 R13: ffffffffa0002420 R14: 0000000000000000 R15: 0000000000000000 FS: 00007f56b75be540(0000) GS:ffff88813bc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffff9ffffff2 CR3: 000000010874a006 CR4: 0000000000330ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __x64_sys_delete_module+0x206/0x380 ? lockdep_hardirqs_on_prepare+0xd8/0x190 ? syscall_enter_from_user_mode+0x1c/0x50 do_syscall_64+0x3f/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd Link: https://lore.kernel.org/all/20221108015130.28326-2-shangxiaojing@huawei.com/ Fixes: 64836248dda2 ("tracing: Add kprobe event command generation test module") Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-09-13 19:00:12 +0300