Age | Commit message (Collapse) | Author | Files | Lines |
|
[ Upstream commit ad9b2b8e53af61375322e3c7d624acf3a3ef53b0 ]
The public S805 datasheet only mentions that
HHI_SYS_CPU_CLK_CNTL1[20:29] contains a divider called "cpu_scale_div".
Unfortunately it does not mention how to use the register contents.
The Amlogic 3.10 GPL kernel sources are using the following code to
calculate the CPU clock based on that register (taken from
arch/arm/mach-meson8/clock.c in the 3.10 Amlogic kernel, shortened to
make it easier to read):
N = (aml_read_reg32(P_HHI_SYS_CPU_CLK_CNTL1) >> 20) & 0x3FF;
if (sel == 3) /* use cpu_scale_div */
div = 2 * N;
else
div = ... /* not relevant for this example */
cpu_clk = parent_clk / div;
This suggests that the formula is: parent_rate / 2 * register_value
However, running perf (which can measure the CPU clock rate thanks to
the ARM PMU) shows that this formula is not correct.
This can be reproduced with the following steps:
1. boot into u-boot
2. let the CPU clock run off the XTAL clock:
mw.l 0xC110419C 0x30 1
3. set the cpu_scale_div register:
to value 0x1: mw.l 0xC110415C 0x801016A2 1
to value 0x2: mw.l 0xC110415C 0x802016A2 1
to value 0x5: mw.l 0xC110415C 0x805016A2 1
4. let the CPU clock run off cpu_scale_div:
mw.l 0xC110419C 0xbd 1
5. boot Linux
6. run: perf stat -aB stress --cpu 4 --timeout 10
7. check the "cycles" value
I get the following results depending on the cpu_scale_div value:
- (cpu_in_sel - this is the input clock for cpu_scale_div - runs at
1.2GHz)
- 0x1 = 300MHz
- 0x2 = 200MHz
- 0x5 = 100MHz
This means that the actual formula to calculate the output of the
cpu_scale_div clock is: parent_rate / 2 * (register value + 1).
The register value 0x0 is reserved. When letting the CPU clock run off
the cpu_scale_div while the value is 0x0 the whole board hangs (even in
u-boot).
I also verified this with the TWD timer: when adding this to the .dts
without specifying it's clock it will auto-detect the PERIPH (which is
the input clock of the TWD) clock rate (and the result is shown in the
kernel log). On Meson8, Meson8b and Meson8m2 the PERIPH clock is CPUCLK
divided by 4. This also matched for all three test-cases from above (in
all cases the TWD timer clock rate was approx. one fourth of the CPU
clock rate).
A small note regarding the "fixes" tag: the original issue seems to
exist virtually since forever. Even commit 28b9fcd016126e ("clk:
meson8b: Add support for Meson8b clocks") seems to handle this wrong. I
still decided to use commit 251b6fd38bcb9c ("clk: meson: rework meson8b
cpu clock") because this is the first commit which gets the CPU hiearchy
correct and thus it's the first commit where the cpu_scale_div register
is used correctly (apart from the bug in the cpu_scale_table).
Fixes: 251b6fd38bcb9c ("clk: meson: rework meson8b cpu clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20180927085921.24627-2-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2de42f79bb21a412f40ade8831eb6fc445cb78a4 ]
Consider the following scenario:
1. nonblocking enable crtc
2. wait for the event
3. nonblocking disable crtc
On i915 this can lead to a spurious -EBUSY from step 3 on
account of non-enabled planes getting the fake_commit in step 1
and we don't complete the fake_commit-> flip_done until
drm_atomic_helper_commit_hw_done() which can happen a long
time after the flip event was sent out.
This will become somewhat easy to hit on SKL+ once we start
to add all the planes for the crtc to every modeset commit
for the purposes of forcing a watermark register programming
[1].
To make the race a little less pronounced let's complete
fake_commit->flip_done after drm_atomic_helper_wait_for_flip_done().
For the single crtc case this should make the race quite
theoretical, assuming drm_atomic_helper_wait_for_flip_done()
actually has to wait for the real commit flip_done. In case
the real commit flip_done gets completed singificantly before
drm_atomic_helper_wait_for_flip_done(), or we are dealing with
multiple crtcs whose vblanks don't line up nicely the race still
exists.
[1] https://patchwork.freedesktop.org/patch/262670/
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 080de2e5be2d ("drm/atomic: Check for busy planes/connectors before setting the commit")
Testcase: igt/kms_cursor_legacy/*nonblocking-modeset-vs-cursor-atomic
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181122143412.11655-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 81e9fa8bab381f8b6eb04df7cdf0f71994099bd4 ]
The armv8_pmuv3 driver doesn't have a remove function, and when the test
'CONFIG_DEBUG_TEST_DRIVER_REMOVE=y' is enabled, the following Call trace
can be seen.
[ 1.424287] Failed to register pmu: armv8_pmuv3, reason -17
[ 1.424870] WARNING: CPU: 0 PID: 1 at ../kernel/events/core.c:11771 perf_event_sysfs_init+0x98/0xdc
[ 1.425220] Modules linked in:
[ 1.425531] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 4.19.0-rc7-next-20181012-00003-ge7a97b1ad77b-dirty #35
[ 1.425951] Hardware name: linux,dummy-virt (DT)
[ 1.426212] pstate: 80000005 (Nzcv daif -PAN -UAO)
[ 1.426458] pc : perf_event_sysfs_init+0x98/0xdc
[ 1.426720] lr : perf_event_sysfs_init+0x98/0xdc
[ 1.426908] sp : ffff00000804bd50
[ 1.427077] x29: ffff00000804bd50 x28: ffff00000934e078
[ 1.427429] x27: ffff000009546000 x26: 0000000000000007
[ 1.427757] x25: ffff000009280710 x24: 00000000ffffffef
[ 1.428086] x23: ffff000009408000 x22: 0000000000000000
[ 1.428415] x21: ffff000009136008 x20: ffff000009408730
[ 1.428744] x19: ffff80007b20b400 x18: 000000000000000a
[ 1.429075] x17: 0000000000000000 x16: 0000000000000000
[ 1.429418] x15: 0000000000000400 x14: 2e79726f74636572
[ 1.429748] x13: 696420656d617320 x12: 656874206e692065
[ 1.430060] x11: 6d616e20656d6173 x10: 2065687420687469
[ 1.430335] x9 : ffff00000804bd50 x8 : 206e6f7361657220
[ 1.430610] x7 : 2c3376756d705f38 x6 : ffff00000954d7ce
[ 1.430880] x5 : 0000000000000000 x4 : 0000000000000000
[ 1.431226] x3 : 0000000000000000 x2 : ffffffffffffffff
[ 1.431554] x1 : 4d151327adc50b00 x0 : 0000000000000000
[ 1.431868] Call trace:
[ 1.432102] perf_event_sysfs_init+0x98/0xdc
[ 1.432382] do_one_initcall+0x6c/0x1a8
[ 1.432637] kernel_init_freeable+0x1bc/0x280
[ 1.432905] kernel_init+0x18/0x160
[ 1.433115] ret_from_fork+0x10/0x18
[ 1.433297] ---[ end trace 27fd415390eb9883 ]---
Rework to set suppress_bind_attrs flag to avoid removing the device when
CONFIG_DEBUG_TEST_DRIVER_REMOVE=y, since there's no real reason to
remove the armv8_pmuv3 driver.
Cc: Arnd Bergmann <arnd@arndb.de>
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3da2c1dfdb802b184eea0653d1e589515b52d74b ]
ecc_point_mult is supposed to be used with a regularized scalar,
otherwise, it's possible to deduce the position of the top bit of the
scalar with timing attack. This is important when the scalar is a
private key.
ecc_point_mult is already using a regular algorithm (i.e. having an
operation flow independent of the input scalar) but regularization step
is not implemented.
Arrange scalar to always have fixed top bit by adding a multiple of the
curve order (n).
References:
The constant time regularization step is based on micro-ecc by Kenneth
MacKay and also referenced in the literature (Bernstein, D. J., & Lange,
T. (2017). Montgomery curves and the Montgomery ladder. (Cryptology
ePrint Archive; Vol. 2017/293). s.l.: IACR. Chapter 4.6.2.)
Signed-off-by: Vitaly Chikunov <vt@altlinux.org>
Cc: kernel-hardening@lists.openwall.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e4849aff1e169b86c561738daf8ff020e9de1011 ]
The Broadcom SiByte BCM1250, BCM1125, and BCM1125H SOCs have an onchip
DRAM controller that supports memory amounts of up to 16GiB, and due to
how the address decoder has been wired in the SOC any memory beyond 1GiB
is actually mapped starting from 4GiB physical up, that is beyond the
32-bit addressable limit[1]. Consequently if the maximum amount of
memory has been installed, then it will span up to 19GiB.
Many of the evaluation boards we support that are based on one of these
SOCs have their memory soldered and the amount present fits in the
32-bit address range. The BCM91250A SWARM board however has actual DIMM
slots and accepts, depending on the peripherals revision of the SOC, up
to 4GiB or 8GiB of memory in commercially available JEDEC modules[2].
I believe this is also the case with the BCM91250C2 LittleSur board.
This means that up to either 3GiB or 7GiB of memory requires 64-bit
addressing to access.
I believe the BCM91480B BigSur board, which has the BCM1480 SOC instead,
accepts at least as much memory, although I have no documentation or
actual hardware available to verify that.
Both systems have PCI slots installed for use by any PCI option boards,
including ones that only support 32-bit addressing (additionally the
32-bit PCI host bridge of the BCM1250, BCM1125, and BCM1125H SOCs limits
addressing to 32-bits), and there is no IOMMU available. Therefore for
PCI DMA to work in the presence of memory beyond enable swiotlb for the
affected systems.
All the other SOC onchip DMA devices use 40-bit addressing and therefore
can address the whole memory, so only enable swiotlb if PCI support and
support for DMA beyond 4GiB have been both enabled in the configuration
of the kernel.
This shows up as follows:
Broadcom SiByte BCM1250 B2 @ 800 MHz (SB1 rev 2)
Board type: SiByte BCM91250A (SWARM)
Determined physical RAM map:
memory: 000000000fe7fe00 @ 0000000000000000 (usable)
memory: 000000001ffffe00 @ 0000000080000000 (usable)
memory: 000000000ffffe00 @ 00000000c0000000 (usable)
memory: 0000000087fffe00 @ 0000000100000000 (usable)
software IO TLB: mapped [mem 0xcbffc000-0xcfffc000] (64MB)
in the bootstrap log and removes failures like these:
defxx 0000:02:00.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0
fddi0: Receive buffer allocation failed
fddi0: Adapter open failed!
IP-Config: Failed to open fddi0
defxx 0000:09:08.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0
fddi1: Receive buffer allocation failed
fddi1: Adapter open failed!
IP-Config: Failed to open fddi1
when memory beyond 4GiB is handed out to devices that can only do 32-bit
addressing.
This updates commit cce335ae47e2 ("[MIPS] 64-bit Sibyte kernels need
DMA32.").
References:
[1] "BCM1250/BCM1125/BCM1125H User Manual", Revision 1250_1125-UM100-R,
Broadcom Corporation, 21 Oct 2002, Section 3: "System Overview",
"Memory Map", pp. 34-38
[2] "BCM91250A User Manual", Revision 91250A-UM100-R, Broadcom
Corporation, 18 May 2004, Section 3: "Physical Description",
"Supported DRAM", p. 23
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
[paul.burton@mips.com: Remove GPL text from dma.c; SPDX tag covers it]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/21108/
References: cce335ae47e2 ("[MIPS] 64-bit Sibyte kernels need DMA32.")
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 68b5e4326e4b8ac9080835005d8254fed0fb3c56 ]
Add the proper includes and make smca_get_name() static.
Fix an actual bug too which the warning triggered:
arch/x86/kernel/cpu/mcheck/therm_throt.c:395:39: error: conflicting \
types for ‘smp_thermal_interrupt’
asmlinkage __visible void __irq_entry smp_thermal_interrupt(struct pt_regs *r)
^~~~~~~~~~~~~~~~~~~~~
In file included from arch/x86/kernel/cpu/mcheck/therm_throt.c:29:
./arch/x86/include/asm/traps.h:107:17: note: previous declaration of \
‘smp_thermal_interrupt’ was here
asmlinkage void smp_thermal_interrupt(void);
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Yi Wang <wang.yi59@zte.com.cn>
Cc: Michael Matz <matz@suse.de>
Cc: x86@kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1811081633160.1549@nanos.tec.linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fba43f454cdf9caa3185219d116bd2a6e6354552 ]
This commit adds support for APOGEE duet FireWire, launched 2007, already
discontinued. This model uses Oxford Semiconductor FW971 as its
communication engine. Below is information on Configuration ROM of this
unit. The unit supports some AV/C commands defined by Audio subunit
specification and vendor dependent commands.
$ ./hinawa-config-rom-printer /dev/fw1
{ 'bus-info': { 'adj': False,
'bmc': False,
'chip_ID': 42949742248,
'cmc': False,
'cyc_clk_acc': 255,
'generation': 0,
'imc': False,
'isc': True,
'link_spd': 3,
'max_ROM': 0,
'max_rec': 64,
'name': '1394',
'node_vendor_ID': 987,
'pmc': False},
'root-directory': [ ['VENDOR', 987],
['DESCRIPTOR', 'Apogee Electronics'],
['MODEL', 122333],
['DESCRIPTOR', 'Duet'],
[ 'NODE_CAPABILITIES',
{ 'addressing': {'64': True, 'fix': True, 'prv': False},
'misc': {'int': False, 'ms': False, 'spt': True},
'state': { 'atn': False,
'ded': False,
'drq': True,
'elo': False,
'init': False,
'lst': True,
'off': False},
'testing': {'bas': False, 'ext': False}}],
[ 'UNIT',
[ ['SPECIFIER_ID', 41005],
['VERSION', 65537],
['MODEL', 122333],
['DESCRIPTOR', 'Duet']]]]}
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 46f53a65d2de3e1591636c22b626b09d8684fd71 ]
Currently BPF verifier allows narrow loads for a context field only with
offset zero. E.g. if there is a __u32 field then only the following
loads are permitted:
* off=0, size=1 (narrow);
* off=0, size=2 (narrow);
* off=0, size=4 (full).
On the other hand LLVM can generate a load with offset different than
zero that make sense from program logic point of view, but verifier
doesn't accept it.
E.g. tools/testing/selftests/bpf/sendmsg4_prog.c has code:
#define DST_IP4 0xC0A801FEU /* 192.168.1.254 */
...
if ((ctx->user_ip4 >> 24) == (bpf_htonl(DST_IP4) >> 24) &&
where ctx is struct bpf_sock_addr.
Some versions of LLVM can produce the following byte code for it:
8: 71 12 07 00 00 00 00 00 r2 = *(u8 *)(r1 + 7)
9: 67 02 00 00 18 00 00 00 r2 <<= 24
10: 18 03 00 00 00 00 00 fe 00 00 00 00 00 00 00 00 r3 = 4261412864 ll
12: 5d 32 07 00 00 00 00 00 if r2 != r3 goto +7 <LBB0_6>
where `*(u8 *)(r1 + 7)` means narrow load for ctx->user_ip4 with size=1
and offset=3 (7 - sizeof(ctx->user_family) = 3). This load is currently
rejected by verifier.
Verifier code that rejects such loads is in bpf_ctx_narrow_access_ok()
what means any is_valid_access implementation, that uses the function,
works this way, e.g. bpf_skb_is_valid_access() for __sk_buff or
sock_addr_is_valid_access() for bpf_sock_addr.
The patch makes such loads supported. Offset can be in [0; size_default)
but has to be multiple of load size. E.g. for __u32 field the following
loads are supported now:
* off=0, size=1 (narrow);
* off=1, size=1 (narrow);
* off=2, size=1 (narrow);
* off=3, size=1 (narrow);
* off=0, size=2 (narrow);
* off=2, size=2 (narrow);
* off=0, size=4 (full).
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 646097940ad35aa2c1f2012af932d55976a9f255 ]
When the test 'CONFIG_DEBUG_TEST_DRIVER_REMOVE=y' is enabled,
arch_initcall(pl011_init) came before subsys_initcall(default_bdi_init).
devtmpfs gets killed because we try to remove a file and decrement the
wb reference count before the noop_backing_device_info gets initialized.
[ 0.332075] Serial: AMBA PL011 UART driver
[ 0.485276] 9000000.pl011: ttyAMA0 at MMIO 0x9000000 (irq = 39, base_baud = 0) is a PL011 rev1
[ 0.502382] console [ttyAMA0] enabled
[ 0.515710] Unable to handle kernel paging request at virtual address 0000800074c12000
[ 0.516053] Mem abort info:
[ 0.516222] ESR = 0x96000004
[ 0.516417] Exception class = DABT (current EL), IL = 32 bits
[ 0.516641] SET = 0, FnV = 0
[ 0.516826] EA = 0, S1PTW = 0
[ 0.516984] Data abort info:
[ 0.517149] ISV = 0, ISS = 0x00000004
[ 0.517339] CM = 0, WnR = 0
[ 0.517553] [0000800074c12000] user address but active_mm is swapper
[ 0.517928] Internal error: Oops: 96000004 [#1] PREEMPT SMP
[ 0.518305] Modules linked in:
[ 0.518839] CPU: 0 PID: 13 Comm: kdevtmpfs Not tainted 4.19.0-rc5-next-20180928-00002-g2ba39ab0cd01-dirty #82
[ 0.519307] Hardware name: linux,dummy-virt (DT)
[ 0.519681] pstate: 80000005 (Nzcv daif -PAN -UAO)
[ 0.519959] pc : __destroy_inode+0x94/0x2a8
[ 0.520212] lr : __destroy_inode+0x78/0x2a8
[ 0.520401] sp : ffff0000098c3b20
[ 0.520590] x29: ffff0000098c3b20 x28: 00000000087a3714
[ 0.520904] x27: 0000000000002000 x26: 0000000000002000
[ 0.521179] x25: ffff000009583000 x24: 0000000000000000
[ 0.521467] x23: ffff80007bb52000 x22: ffff80007bbaa7c0
[ 0.521737] x21: ffff0000093f9338 x20: 0000000000000000
[ 0.522033] x19: ffff80007bbb05d8 x18: 0000000000000400
[ 0.522376] x17: 0000000000000000 x16: 0000000000000000
[ 0.522727] x15: 0000000000000400 x14: 0000000000000400
[ 0.523068] x13: 0000000000000001 x12: 0000000000000001
[ 0.523421] x11: 0000000000000000 x10: 0000000000000970
[ 0.523749] x9 : ffff0000098c3a60 x8 : ffff80007bbab190
[ 0.524017] x7 : ffff80007bbaa880 x6 : 0000000000000c88
[ 0.524305] x5 : ffff0000093d96c8 x4 : 61c8864680b583eb
[ 0.524567] x3 : ffff0000093d6180 x2 : ffffffffffffffff
[ 0.524872] x1 : 0000800074c12000 x0 : 0000800074c12000
[ 0.525207] Process kdevtmpfs (pid: 13, stack limit = 0x(____ptrval____))
[ 0.525529] Call trace:
[ 0.525806] __destroy_inode+0x94/0x2a8
[ 0.526108] destroy_inode+0x34/0x88
[ 0.526370] evict+0x144/0x1c8
[ 0.526636] iput+0x184/0x230
[ 0.526871] dentry_unlink_inode+0x118/0x130
[ 0.527152] d_delete+0xd8/0xe0
[ 0.527420] vfs_unlink+0x240/0x270
[ 0.527665] handle_remove+0x1d8/0x330
[ 0.527875] devtmpfsd+0x138/0x1c8
[ 0.528085] kthread+0x14c/0x158
[ 0.528291] ret_from_fork+0x10/0x18
[ 0.528720] Code: 92800002 aa1403e0 d538d081 8b010000 (c85f7c04)
[ 0.529367] ---[ end trace 5a3dee47727f877c ]---
Rework to set suppress_bind_attrs flag to avoid removing the device when
CONFIG_DEBUG_TEST_DRIVER_REMOVE=y. This applies for pic32_uart and
xilinx_uartps as well.
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 347a28b586802d09604a149c1a1f6de5dccbe6fa ]
This happened while running in qemu-system-aarch64, the AMBA PL011 UART
driver when enabling CONFIG_DEBUG_TEST_DRIVER_REMOVE.
arch_initcall(pl011_init) came before subsys_initcall(default_bdi_init),
devtmpfs' handle_remove() crashes because the reference count is a NULL
pointer only because wb->bdi hasn't been initialized yet.
Rework so that wb_put have an extra check if wb->bdi before decrement
wb->refcnt and also add a WARN_ON_ONCE to get a warning if it happens again
in other drivers.
Fixes: 52ebea749aae ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks")
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c528e457d53c75107d5aa56892316d265c778de ]
The refcount of a newly added overlay node decrements to one
(instead of zero) when the overlay changeset is destroyed. This
change will cause the final decrement be to zero.
After applying this patch, new validation warnings will be
reported from the devicetree unittest during boot due to
a pre-existing devicetree bug. The warnings will be similar to:
OF: ERROR: memory leak before free overlay changeset, /testcase-data/overlay-node/test-bus/test-unittest4
This pre-existing devicetree bug will also trigger a WARN_ONCE() from
refcount_sub_and_test_checked() when an overlay changeset is
destroyed without having first been applied. This scenario occurs
when an error in the overlay is detected during the overlay changeset
creation:
WARNING: CPU: 0 PID: 1 at lib/refcount.c:187 refcount_sub_and_test_checked+0xa8/0xbc
refcount_t: underflow; use-after-free.
(unwind_backtrace) from (show_stack+0x10/0x14)
(show_stack) from (dump_stack+0x6c/0x8c)
(dump_stack) from (__warn+0xdc/0x104)
(__warn) from (warn_slowpath_fmt+0x44/0x6c)
(warn_slowpath_fmt) from (refcount_sub_and_test_checked+0xa8/0xbc)
(refcount_sub_and_test_checked) from (kobject_put+0x24/0x208)
(kobject_put) from (of_changeset_destroy+0x2c/0xb4)
(of_changeset_destroy) from (free_overlay_changeset+0x1c/0x9c)
(free_overlay_changeset) from (of_overlay_remove+0x284/0x2cc)
(of_overlay_remove) from (of_unittest_apply_revert_overlay_check.constprop.4+0xf8/0x1e8)
(of_unittest_apply_revert_overlay_check.constprop.4) from (of_unittest_overlay+0x960/0xed8)
(of_unittest_overlay) from (of_unittest+0x1cc4/0x2138)
(of_unittest) from (do_one_initcall+0x4c/0x28c)
(do_one_initcall) from (kernel_init_freeable+0x29c/0x378)
(kernel_init_freeable) from (kernel_init+0x8/0x110)
(kernel_init) from (ret_from_fork+0x14/0x2c)
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f96afa767baffba7645f5e10998f5178948bb9aa ]
libbpf is now able to load successfully test_l4lb_noinline.o and
samples/bpf/tracex3_kern.o.
For the test_l4lb_noinline, uncomment related tests from test_libbpf.c
and remove the associated "TODO".
For tracex3_kern.o, instead of loading a program from samples/bpf/ that
might not have been compiled at this stage, try loading a program from
BPF selftests. Since this test case is about loading a program compiled
without the "-target bpf" flag, change the Makefile to compile one
program accordingly (instead of passing the flag for compiling all
programs).
Regarding test_xdp_noinline.o: in its current shape the program fails to
load because it provides no version section, but the loader needs one.
The test was added to make sure that libbpf could load XDP programs even
if they do not provide a version number in a dedicated section. But
libbpf is already capable of doing that: in our case loading fails
because the loader does not know that this is an XDP program (it does
not need to, since it does not attach the program). So trying to load
test_xdp_noinline.o does not bring much here: just delete this subtest.
For the record, the error message obtained with tracex3_kern.o was
fixed by commit e3d91b0ca523 ("tools/libbpf: handle issues with bpf ELF
objects containing .eh_frames")
I have not been abled to reproduce the "libbpf: incorrect bpf_call
opcode" error for test_l4lb_noinline.o, even with the version of libbpf
present at the time when test_libbpf.sh and test_libbpf_open.c were
created.
RFC -> v1:
- Compile test_xdp without the "-target bpf" flag, and try to load it
instead of ../../samples/bpf/tracex3_kern.o.
- Delete test_xdp_noinline.o subtest.
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 23b5f73266e59a598c1e5dd435d87651b5a7626b ]
During HARD_RESET the data link is disconnected.
For self powered device, the spec is advising against doing that.
>From USB_PD_R3_0
7.1.5 Response to Hard Resets
Device operation during and after a Hard Reset is defined as follows:
Self-powered devices Should Not disconnect from USB during a Hard Reset
(see Section 9.1.2).
Bus powered devices will disconnect from USB during a Hard Reset due to the
loss of their power source.
Tackle this by letting TCPM know whether the device is self or bus powered.
This overcomes unnecessary port disconnections from hard reset.
Also, speeds up the enumeration time when connected to Type-A ports.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
---------
Version history:
V3:
Rebase on top of usb-next
V2:
Based on feedback from heikki.krogerus@linux.intel.com
- self_powered added to the struct tcpm_port which is populated from
a. "connector" node of the device tree in tcpm_fw_get_caps()
b. "self_powered" node of the tcpc_config in tcpm_copy_caps
Based on feedbase from linux@roeck-us.net
- Code was refactored
- SRC_HARD_RESET_VBUS_OFF sets the link state to false based
on self_powered flag
V1 located here:
https://lkml.org/lkml/2018/9/13/94
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e1f65b0d70e9e5c80e15105cd96fa00174d7c436 ]
It seems with some NICs supported by the e1000e driver a SYSTIM reading
may occasionally be few microseconds before the previous reading and if
enabled also pass e1000e_sanitize_systim() without reaching the maximum
number of rereads, even if the function is modified to check three
consecutive readings (i.e. it doesn't look like a double read error).
This causes an underflow in the timecounter and the PHC time jumps hours
ahead.
This was observed on 82574, I217 and I219. The fastest way to reproduce
it is to run a program that continuously calls the PTP_SYS_OFFSET ioctl
on the PHC.
Modify e1000e_phc_gettime() to use timecounter_cyc2time() instead of
timecounter_read() in order to allow non-monotonic SYSTIM readings and
prevent the PHC from jumping.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 78f3ac76d9e5219589718b9e4733bee21627b3f5 ]
In the past, Asus firmwares would change the panel backlight directly
through the EC when the display off hotkey (Fn+F7) was pressed, and
only notify the OS of such change, with 0x33 when the LCD was ON and
0x34 when the LCD was OFF. These are currently mapped to
KEY_DISPLAYTOGGLE and KEY_DISPLAY_OFF, respectively.
Most recently the EC on Asus most machines lost ability to toggle the
LCD backlight directly, but unless the OS informs the firmware it is
going to handle the display toggle hotkey events, the firmware still
tries change the brightness through the EC, to no effect. The end result
is a long list (at Endless we counted 11) of Asus laptop models where
the display toggle hotkey does not perform any action. Our firmware
engineers contacts at Asus were surprised that there were still machines
out there with the old behavior.
Calling WMNB(ASUS_WMI_DEVID_BACKLIGHT==0x00050011, 2) on the _WDG device
tells the firmware that it should let the OS handle the display toggle
event, in which case it will simply notify the OS of a key press with
0x35, as shown by the DSDT excerpts bellow.
Scope (_SB)
{
(...)
Device (ATKD)
{
(...)
Name (_WDG, Buffer (0x28)
{
/* 0000 */ 0xD0, 0x5E, 0x84, 0x97, 0x6D, 0x4E, 0xDE, 0x11,
/* 0008 */ 0x8A, 0x39, 0x08, 0x00, 0x20, 0x0C, 0x9A, 0x66,
/* 0010 */ 0x4E, 0x42, 0x01, 0x02, 0x35, 0xBB, 0x3C, 0x0B,
/* 0018 */ 0xC2, 0xE3, 0xED, 0x45, 0x91, 0xC2, 0x4C, 0x5A,
/* 0020 */ 0x6D, 0x19, 0x5D, 0x1C, 0xFF, 0x00, 0x01, 0x08
})
Method (WMNB, 3, Serialized)
{
CreateDWordField (Arg2, Zero, IIA0)
CreateDWordField (Arg2, 0x04, IIA1)
Local0 = (Arg1 & 0xFFFFFFFF)
(...)
If ((Local0 == 0x53564544))
{
(...)
If ((IIA0 == 0x00050011))
{
If ((IIA1 == 0x02))
{
^^PCI0.SBRG.EC0.SPIN (0x72, One)
^^PCI0.SBRG.EC0.BLCT = One
}
Return (One)
}
}
(...)
}
(...)
}
(...)
}
(...)
Scope (_SB.PCI0.SBRG.EC0)
{
(...)
Name (BLCT, Zero)
(...)
Method (_Q10, 0, NotSerialized) // _Qxx: EC Query
{
If ((BLCT == Zero))
{
Local0 = One
Local0 = RPIN (0x72)
Local0 ^= One
SPIN (0x72, Local0)
If (ATKP)
{
Local0 = (0x34 - Local0)
^^^^ATKD.IANE (Local0)
}
}
ElseIf ((BLCT == One))
{
If (ATKP)
{
^^^^ATKD.IANE (0x35)
}
}
}
(...)
}
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7fa57ca443cffe81ce8416b57966bfb0370678a1 ]
When it's possible that the PF might end up trying to send a
packet to one of its own VFs, we have to forbid IPsec offload
because the device drops the packets into a black hole.
See commit 47b6f50077e6 ("ixgbe: disallow IPsec Tx offload
when in SR-IOV mode") for more info.
This really is only necessary when the device is in the default
VEB mode. If instead the device is running in VEPA mode,
the packets will go through the encryption engine and out the
MAC/PHY as normal, and get "hairpinned" as needed by the switch.
So let's not block IPsec offload when in VEPA mode. To get
there with the ixgbe device, use the handy 'bridge' command:
bridge link set dev eth1 hwmode vepa
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2383a767c0ca06f96534456d8313909017c6c8d0 ]
Vega10 has multiple interrupt rings, so this can be called from multiple
calles at the same time resulting in:
[ 71.779334] ================================
[ 71.779406] WARNING: inconsistent lock state
[ 71.779478] 4.19.0-rc1+ #44 Tainted: G W
[ 71.779565] --------------------------------
[ 71.779637] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[ 71.779740] kworker/6:1/120 [HC0[0]:SC0[0]:HE1:SE1] takes:
[ 71.779832] 00000000ad761971 (&(&kfd->interrupt_lock)->rlock){?...},
at: kgd2kfd_interrupt+0x75/0x100 [amdgpu]
[ 71.780058] {IN-HARDIRQ-W} state was registered at:
[ 71.780115] _raw_spin_lock+0x2c/0x40
[ 71.780180] kgd2kfd_interrupt+0x75/0x100 [amdgpu]
[ 71.780248] amdgpu_irq_callback+0x6c/0x150 [amdgpu]
[ 71.780315] amdgpu_ih_process+0x88/0x100 [amdgpu]
[ 71.780380] amdgpu_irq_handler+0x20/0x40 [amdgpu]
[ 71.780409] __handle_irq_event_percpu+0x49/0x2a0
[ 71.780436] handle_irq_event_percpu+0x30/0x70
[ 71.780461] handle_irq_event+0x37/0x60
[ 71.780484] handle_edge_irq+0x83/0x1b0
[ 71.780506] handle_irq+0x1f/0x30
[ 71.780526] do_IRQ+0x53/0x110
[ 71.780544] ret_from_intr+0x0/0x22
[ 71.780566] cpuidle_enter_state+0xaa/0x330
[ 71.780591] do_idle+0x203/0x280
[ 71.780610] cpu_startup_entry+0x6f/0x80
[ 71.780634] start_secondary+0x1b0/0x200
[ 71.780657] secondary_startup_64+0xa4/0xb0
Fix this by always using irq save spin locks.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f41a895026b8cb6f765190de7d2e7bc3ccbbd183 ]
[Why]
The igt@kms_plane@pixel-format-pipe tests can create a sequence where
stream_state is NULL during amdgpu_dm_crtc_set_crc_source which results
in a null pointer dereference.
[How]
Guard against stream_state being NULL before accessing its fields. This
doesn't fix the root cause of the issue so a DRM_ERROR is generated
to still fail the tests.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ed8dce4c6f726b7f3c6bf40859b92a9e32f189c1 ]
Keeping the irq_chip definition static will make it shared with multiple
giochips in the system. This practice is considered to be bad and now we
will get the below warning from gpiolib core:
"detected irqchip that is shared with multiple gpiochips: please fix the
driver."
Hence, move the irq_chip definition from static to `struct pl061` for
using a unique irq_chip for each gpiochip.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
ipmac sets
[ Upstream commit 8cc4ccf58379935f3ad456cc34e61c4e4c921d0e ]
There doesn't seem to be any reason to restrict MAC address
matching to source MAC addresses in set types bitmap:ipmac,
hash:ipmac and hash:mac. With this patch, and this setup:
ip netns add A
ip link add veth1 type veth peer name veth2 netns A
ip addr add 192.0.2.1/24 dev veth1
ip -net A addr add 192.0.2.2/24 dev veth2
ip link set veth1 up
ip -net A link set veth2 up
ip netns exec A ipset create test hash:mac
dst=$(ip netns exec A cat /sys/class/net/veth2/address)
ip netns exec A ipset add test ${dst}
ip netns exec A iptables -P INPUT DROP
ip netns exec A iptables -I INPUT -m set --match-set test dst -j ACCEPT
ipset will match packets based on destination MAC address:
# ping -c1 192.0.2.2 >/dev/null
# echo $?
0
Reported-by: Yi Chen <yiche@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 41d1c8839e5f8cb781cc635f12791decee8271b7 ]
Matteo reported forwarding issues inside the linux bridge,
if the enslaved interfaces use the fq qdisc.
Similar to commit 8203e2d844d3 ("net: clear skb->tstamp in
forwarding paths"), we need to clear the tstamp field in
the bridge forwarding path.
Fixes: 80b14dee2bea ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC")
Reported-and-tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d4a7e9bb74b5aaf07b89f6531c080b1130bdf019 ]
I realized the last patch calls dev_get_by_index_rcu in a branch not
holding the rcu lock. Add the calls to rcu_read_lock and rcu_read_unlock.
Fixes: ec90ad334986 ("ipv6: Consider sk_bound_dev_if when binding a socket to a v4 mapped address")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 36352991835ce99e46b4441dd0eb6980f9a83e8f ]
There are two new Realtek Ethernet devices which are re-branded r8168h.
Add the IDs to to support them.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f87118d5760f00af7228033fbe783c7f380d2866 ]
This patch adds MTU default value to qmap network interface in
order to avoid "RTNETLINK answers: No buffer space available"
error when setting an ipv6 address.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f8c468e8537925e0c4607263f498a1b7c0c8982e ]
Commit dcda9b04713c ("mm, tree wide: replace __GFP_REPEAT by
__GFP_RETRY_MAYFAIL with more useful semantic") replaced __GFP_REPEAT in
alloc_skb_with_frags() with __GFP_RETRY_MAYFAIL when the allocation may
directly reclaim.
The previous behavior would require reclaim up to 1 << order pages for
skb aligned header_len of order > PAGE_ALLOC_COSTLY_ORDER before failing,
otherwise the allocations in alloc_skb() would loop in the page allocator
looking for memory. __GFP_RETRY_MAYFAIL makes both allocations failable
under memory pressure, including for the HEAD allocation.
This can cause, among many other things, write() to fail with ENOTCONN
during RPC when under memory pressure.
These allocations should succeed as they did previous to dcda9b04713c
even if it requires calling the oom killer and additional looping in the
page allocator to find memory. There is no way to specify the previous
behavior of __GFP_REPEAT, but it's unlikely to be necessary since the
previous behavior only guaranteed that 1 << order pages would be reclaimed
before failing for order > PAGE_ALLOC_COSTLY_ORDER. That reclaim is not
guaranteed to be contiguous memory, so repeating for such large orders is
usually not beneficial.
Removing the setting of __GFP_RETRY_MAYFAIL to restore the previous
behavior, specifically not allowing alloc_skb() to fail for small orders
and oom kill if necessary rather than allowing RPCs to fail.
Fixes: dcda9b04713c ("mm, tree wide: replace __GFP_REPEAT by __GFP_RETRY_MAYFAIL with more useful semantic")
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ea89098ef9a574bceca00d3b5df14aaf0b3f9ccf ]
The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 674bed5df4cab8f96d04f7b99608883a48f9226b ]
When a VLAN is deleted from a bridge port we should not change the PVID
unless the deleted VLAN is the PVID.
Fixes: fe9ccc785de5 ("mlxsw: spectrum_switchdev: Don't batch VLAN operations")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8adbe212a159d9c78a90fca1d854f6e63452426b ]
Make sure that lag port TX is disabled before mlxsw_sp_port_lag_leave()
is called and prevent from possible EMAD error.
Fixes: 0d65fc13042f ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ec90ad334986fa5856d11dd272f7f22fa86c55c4 ]
Similar to c5ee066333eb ("ipv6: Consider sk_bound_dev_if when binding a
socket to an address"), binding a socket to v4 mapped addresses needs to
consider if the socket is bound to a device.
This problem also exists from the beginning of git history.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
commit c8a83a6b54d0ca078de036aafb3f6af58c1dc5eb upstream.
NBD can update block device block size implicitely through
bd_set_size(). Make it explicitely set blocksize with set_blocksize() as
this behavior of bd_set_size() is going away.
CC: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c06ef2e9acef4cda1feee2ce055b8086e33d251a upstream.
As reported by smatch:
drivers/media/common/videobuf2/videobuf2-core.c: drivers/media/common/videobuf2/videobuf2-core.c:2159 vb2_mmap() warn: inconsistent returns 'mutex:&q->mmap_lock'.
Locked on: line 2148
Unlocked on: line 2100
line 2108
line 2113
line 2118
line 2156
line 2159
There is one error condition that doesn't unlock a mutex.
Fixes: cd26d1c4d1bc ("media: vb2: vb2_mmap: move lock up")
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 211929fd3f7c8de4d541b1cc243b82830e5ea1e8 upstream.
Commit b2d35fa5fc80 ("selftests: add headers_install to lib.mk") added
khdr target to run headers_install target from the main Makefile. The
logic uses KSFT_KHDR_INSTALL and top_srcdir as controls to initialize
variables and include files to run headers_install from the top level
Makefile. There are a few problems with this logic.
1. Exposes top_srcdir to all tests
2. Common logic impacts all tests
3. Uses KSFT_KHDR_INSTALL, top_srcdir, and khdr in an adhoc way. Tests
add "khdr" dependency in their Makefiles to TEST_PROGS_EXTENDED in
some cases, and STATIC_LIBS in other cases. This makes this framework
confusing to use.
The common logic that runs for all tests even when KSFT_KHDR_INSTALL
isn't defined by the test. top_srcdir is initialized to a default value
when test doesn't initialize it. It works for all tests without a sub-dir
structure and tests with sub-dir structure fail to build.
e.g: make -C sparc64/drivers/ or make -C drivers/dma-buf
../../lib.mk:20: ../../../../scripts/subarch.include: No such file or directory
make: *** No rule to make target '../../../../scripts/subarch.include'. Stop.
There is no reason to require all tests to define top_srcdir and there is
no need to require tests to add khdr dependency using adhoc changes to
TEST_* and other variables.
Fix it with a consistent use of KSFT_KHDR_INSTALL and top_srcdir from tests
that have the dependency on headers_install.
Change common logic to include khdr target define and "all" target with
dependency on khdr when KSFT_KHDR_INSTALL is defined.
Only tests that have dependency on headers_install have to define just
the KSFT_KHDR_INSTALL, and top_srcdir variables and there is no need to
specify khdr dependency in the test Makefiles.
Fixes: b2d35fa5fc80 ("selftests: add headers_install to lib.mk")
Cc: stable@vger.kernel.org
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66a8d5bfb518f9f12d47e1d2dce1732279f9451e upstream.
Strict requirement of pixclock to be zero breaks support of SDL 1.2
which contains hardcoded table of supported video modes with non-zero
pixclock values[1].
To better understand which pixclock values are considered valid and how
driver should handle these values, I briefly examined few existing fbdev
drivers and documentation in Documentation/fb/. And it looks like there
are no strict rules on that and actual behaviour varies:
* some drivers treat (pixclock == 0) as "use defaults" (uvesafb.c);
* some treat (pixclock == 0) as invalid value which leads to
-EINVAL (clps711x-fb.c);
* some pass converted pixclock value to hardware (uvesafb.c);
* some are trying to find nearest value from predefined table
(vga16fb.c, video_gx.c).
Given this, I believe that it should be safe to just ignore this value if
changing is not supported. It seems that any portable fbdev application
which was not written only for one specific device working under one
specific kernel version should not rely on any particular behaviour of
pixclock anyway.
However, while enabling SDL1 applications to work out of the box when
there is no /etc/fb.modes with valid settings, this change affects the
video mode choosing logic in SDL. Depending on current screen
resolution, contents of /etc/fb.modes and resolution requested by
application, this may lead to user-visible difference (not always):
image will be displayed in a right way, but it will be aligned to the
left instead of center. There is no "right behaviour" here as well, as
emulated fbdev, opposing to old fbdev drivers, simply ignores any
requsts of video mode changes with resolutions smaller than current.
The easiest way to reproduce this problem is to install sdl-sopwith[2],
remove /etc/fb.modes file if it exists, and then try to run sopwith
from console without X. At least in Fedora 29, sopwith may be simply
installed from standard repositories.
[1] SDL 1.2.15 source code, src/video/fbcon/SDL_fbvideo.c, vesa_timings
[2] http://sdl-sopwith.sourceforge.net/
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Cc: stable@vger.kernel.org
Fixes: 79e539453b34e ("DRM: i915: add mode setting support")
Fixes: 771fe6b912fca ("drm/radeon: introduce kernel modesetting for radeon hardware")
Fixes: 785b93ef8c309 ("drm/kms: move driver specific fb common code to helper functions (v2)")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108072353.28078-3-mironov.ivan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5db470e229e22b7eda6e23b5566e532c96fb5bc3 upstream.
If we don't drop caches used in old offset or block_size, we can get old data
from new offset/block_size, which gives unexpected data to user.
For example, Martijn found a loopback bug in the below scenario.
1) LOOP_SET_FD loads first two pages on loop file
2) LOOP_SET_STATUS64 changes the offset on the loop file
3) mount is failed due to the cached pages having wrong superblock
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Reported-by: Martijn Coenen <maco@google.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 628bd85947091830a8c4872adfd5ed1d515a9cf2 upstream.
Commit 0a42e99b58a20883 ("loop: Get rid of loop_index_mutex") forgot to
remove mutex_unlock(&loop_ctl_mutex) from loop_control_ioctl() when
replacing loop_index_mutex with loop_ctl_mutex.
Fixes: 0a42e99b58a20883 ("loop: Get rid of loop_index_mutex")
Reported-by: syzbot <syzbot+c0138741c2290fc5e63f@syzkaller.appspotmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c28445fa06a3a54e06938559b9514c5a7f01c90f upstream.
The nested acquisition of loop_ctl_mutex (->lo_ctl_mutex back then) has
been introduced by commit f028f3b2f987e "loop: fix circular locking in
loop_clr_fd()" to fix lockdep complains about bd_mutex being acquired
after lo_ctl_mutex during partition rereading. Now that these are
properly fixed, let's stop fooling lockdep.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1dded9acf6dc9a34cd27fcf8815507e4e65b3c4f upstream.
Code in loop_change_fd() drops reference to the old file (and also the
new file in a failure case) under loop_ctl_mutex. Similarly to a
situation in loop_set_fd() this can create a circular locking dependency
if this was the last reference holding the file open. Delay dropping of
the file reference until we have released loop_ctl_mutex.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0da03cab87e6323ff2e05b14bc7d5c6fcc531efd upstream.
Calling blkdev_reread_part() under loop_ctl_mutex causes lockdep to
complain about circular lock dependency between bdev->bd_mutex and
lo->lo_ctl_mutex. The problem is that on loop device open or close
lo_open() and lo_release() get called with bdev->bd_mutex held and they
need to acquire loop_ctl_mutex. OTOH when loop_reread_partitions() is
called with loop_ctl_mutex held, it will call blkdev_reread_part() which
acquires bdev->bd_mutex. See syzbot report for details [1].
Move call to blkdev_reread_part() in __loop_clr_fd() from under
loop_ctl_mutex to finish fixing of the lockdep warning and the possible
deadlock.
[1] https://syzkaller.appspot.com/bug?id=bf154052f0eea4bc7712499e4569505907d1588
Reported-by: syzbot <syzbot+4684a000d5abdade83fac55b1e7d1f935ef1936e@syzkaller.appspotmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 85b0a54a82e4fbceeb1aebb7cb6909edd1a24668 upstream.
Calling loop_reread_partitions() under loop_ctl_mutex causes lockdep to
complain about circular lock dependency between bdev->bd_mutex and
lo->lo_ctl_mutex. The problem is that on loop device open or close
lo_open() and lo_release() get called with bdev->bd_mutex held and they
need to acquire loop_ctl_mutex. OTOH when loop_reread_partitions() is
called with loop_ctl_mutex held, it will call blkdev_reread_part() which
acquires bdev->bd_mutex. See syzbot report for details [1].
Move all calls of loop_rescan_partitions() out of loop_ctl_mutex to
avoid lockdep warning and fix deadlock possibility.
[1] https://syzkaller.appspot.com/bug?id=bf154052f0eea4bc7712499e4569505907d1588
Reported-by: syzbot <syzbot+4684a000d5abdade83fac55b1e7d1f935ef1936e@syzkaller.appspotmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d57f3374ba4817f7c8d26fae8a13d20ac8d31b92 upstream.
The call of __blkdev_reread_part() from loop_reread_partition() happens
only when we need to invalidate partitions from loop_release(). Thus
move a detection for this into loop_clr_fd() and simplify
loop_reread_partition().
This makes loop_reread_partition() safe to use without loop_ctl_mutex
because we use only lo->lo_number and lo->lo_file_name in case of error
for reporting purposes (thus possibly reporting outdate information is
not a big deal) and we are safe from 'lo' going away under us by
elevated lo->lo_refcnt.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c371077000f4138ee3c15fbed50101ff24bdc91d upstream.
Push loop_ctl_mutex down to loop_change_fd(). We will need this to be
able to call loop_reread_partitions() without loop_ctl_mutex.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 757ecf40b7e029529768eb5f9562d5eeb3002106 upstream.
Push lo_ctl_mutex down to loop_set_fd(). We will need this to be able to
call loop_reread_partitions() without lo_ctl_mutex.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 550df5fdacff94229cde0ed9b8085155654c1696 upstream.
Push loop_ctl_mutex down to loop_set_status(). We will need this to be
able to call loop_reread_partitions() without loop_ctl_mutex.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4a5ce9ba5877e4640200d84a735361306ad1a1b8 upstream.
Push loop_ctl_mutex down to loop_get_status() to avoid the unusual
convention that the function gets called with loop_ctl_mutex held and
releases it.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7ccd0791d98531df7cd59e92d55e4f063d48a070 upstream.
loop_clr_fd() has a weird locking convention that is expects
loop_ctl_mutex held, releases it on success and keeps it on failure.
Untangle the mess by moving locking of loop_ctl_mutex into
loop_clr_fd().
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a2505b799a496b7b84d9a4a14ec870ff9e42e11b upstream.
Move setting of lo_state to Lo_rundown out into the callers. That will
allow us to unlock loop_ctl_mutex while the loop device is protected
from other changes by its special state.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a13165441d58b216adbd50252a9cc829d78a6bce upstream.
Push acquisition of lo_ctl_mutex down into individual ioctl handling
branches. This is a preparatory step for pushing the lock down into
individual ioctl handling functions so that they can release the lock as
they need it. We also factor out some simple ioctl handlers that will
not need any special handling to reduce unnecessary code duplication.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a42e99b58a208839626465af194cfe640ef9493 upstream.
Now that loop_ctl_mutex is global, just get rid of loop_index_mutex as
there is no good reason to keep these two separate and it just
complicates the locking.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 967d1dc144b50ad005e5eecdfadfbcfb399ffff6 upstream.
__loop_release() has a single call site. Fold it there. This is
currently not a huge win but it will make following replacement of
loop_index_mutex more obvious.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|