| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then, complementing commit 6cbe45d8ac93 ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable <stable@kernel.org>
Fixes: 1bc8cde46a159 ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 4516d50aabed ("serial: 8250: Use canary to restart console after suspend")
Cc: stable@vger.kernel.org # v4.0+
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.8.1 states that XON/XOFF characters
shall be used instead of Fcon/Fcoff command in advanced option mode to
handle flow control. Chapter 5.4.8.2 describes how XON/XOFF characters
shall be handled. Basic option mode only used Fcon/Fcoff commands and no
XON/XOFF characters. These are treated as data bytes here.
The current implementation uses the gsm_mux field 'constipated' to handle
flow control from the remote peer and the gsm_dlci field 'constipated' to
handle flow control from each DLCI. The later is unrelated to this patch.
The gsm_mux field is correctly set for Fcon/Fcoff commands in
gsm_control_message(). However, the same is not true for XON/XOFF
characters in gsm1_receive().
Disable software flow control handling in the tty to allow explicit
handling by n_gsm.
Add the missing handling in advanced option mode for gsm_mux in
gsm1_receive() to comply with the standard.
This patch depends on the following commit:
Commit 8838b2af23ca ("tty: n_gsm: fix SW flow control encoding/handling")
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 states that the Modem Status
Command (MSC) shall only be used if the basic option was chosen.
The current implementation uses MSC frames even if advanced option was
chosen to inform the peer about modem line state updates. A standard
conform peer may choose to discard these frames in advanced option mode.
Furthermore, gsmtty_modem_update() is not part of the 'tty_operations'
functions despite its name.
Rename gsmtty_modem_update() to gsm_modem_update() to clarify this. Split
its function into gsm_modem_upd_via_data() and gsm_modem_upd_via_msc()
depending on the encoding and adaption. Introduce gsm_dlci_modem_output()
as adaption of gsm_dlci_data_output() to encode and queue empty frames in
advanced option mode. Use it in gsm_modem_upd_via_data().
gsm_modem_upd_via_msc() is based on the initial gsmtty_modem_update()
function which used only MSC frames to update modem states.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Dynamic virtual tty registration was introduced to allow the user to handle
these cases with uevent rules. The following commits relate to this:
Commit 5b87686e3203 ("tty: n_gsm: Modify gsmtty driver register method when config requester")
Commit 0b91b5332368 ("tty: n_gsm: Save dlci address open status when config requester")
Commit 46292622ad73 ("tty: n_gsm: clean up indenting in gsm_queue()")
However, the following behavior can be seen with this implementation:
- n_gsm ldisc is activated via ioctl
- all configuration parameters are set to their default value (initiator=0)
- the mux gets activated and attached and gsmtty0 is being registered in
in gsm_dlci_open() after DLCI 0 was established (DLCI 0 is the control
channel)
- the user configures n_gsm via ioctl GSMIOC_SETCONF as initiator
- this re-attaches the n_gsm mux
- no new gsmtty devices are registered in gsmld_attach_gsm() because the
mux is already active
- the initiator side registered only the control channel as gsmtty0
(which should never happen) and no user channel tty
The commits above make it impossible to operate the initiator side as no
user channel tty is or will be available.
On the other hand, this behavior will make it also impossible to allow DLCI
parameter negotiation on responder side in the future. The responder side
first needs to provide a device for the application before the application
can set its parameters of the associated DLCI via ioctl.
Note that the user application is still able to detect a link establishment
without relaying to uevent by waiting for DTR open on responder side. This
is the same behavior as on a physical serial interface. And on initiator
side a tty hangup can be detected if a link establishment request failed.
Revert the commits above completely to always register all user channels
and no control channel after mux attachment. No other changes are made.
Fixes: 5b87686e3203 ("tty: n_gsm: Modify gsmtty driver register method when config requester")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 927728a34f11b5a27f4610bdb7068317d6fdc72a.
Once the uart_port->rs485->flag is set to SER_RS485_ENABLED, the port
should always work in RS485 mode. If users want the port to leave
RS485 mode, they need to call ioctl() to clear SER_RS485_ENABLED.
So here we shouldn't clear the RS485 bits in the shutdown().
Fixes: 927728a34f11 ("serial: sc16is7xx: Clear RS485 bits in the shutdown")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20220418094339.678144-1-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the peer is not informed about the initial state of the modem
control lines after a new DLCI has been opened.
Fix this by sending the initial modem control line states after DLCI open.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220420101346.3315-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 932d596378b0 ("serial: 8250: Return early in .start_tx() if there
are no chars to send") caused a regression where the drivers implementing
runtime PM stopped idling. This is because serial8250_rpm_put_tx() is now
unbalanced on early return, it normally gets called at __stop_tx().
Fixes: 932d596378b0 ("serial: 8250: Return early in .start_tx() if there are no chars to send")
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220411111657.16744-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 76821e222c18 ("serial: imx: ensure that RX irqs are off if RX is
off") accidentally enabled overrun interrupts unconditionally when
deferring DMA enable until after the receiver has been enabled during
startup.
Fix this by using the DMA-initialised instead of DMA-enabled flag to
determine whether overrun interrupts should be enabled.
Note that overrun interrupts are already accounted for in
imx_uart_clear_rx_errors() when using DMA since commit 41d98b5da92f
("serial: imx-serial - update RX error counters when DMA is used").
Fixes: 76821e222c18 ("serial: imx: ensure that RX irqs are off if RX is off")
Cc: stable@vger.kernel.org # 4.17
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20220411081957.7846-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current timeout for draining the tx fifo in RS485 mode is calculated by
multiplying the time it takes to transmit one character (with the given
baud rate) with the maximal number of characters in the tx queue.
This timeout is too short for two reasons:
First when calculating the time to transmit one character integer division
is used which may round down the result in case of a remainder of the
division.
Fix this by rounding up the division result.
Second the hardware may need additional time (e.g for first putting the
characters from the fifo into the shift register) before the characters are
actually put onto the wire.
To be on the safe side double the current maximum number of iterations
that are used to wait for the queue draining.
Fixes: 8d479237727c ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220408233503.7251-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.4.2 states that any received unnumbered
acknowledgment (UA) with its poll/final (PF) bit set to 0 shall be
discarded. Currently, all UA frame are handled in the same way regardless
of the PF bit. This does not comply with the standard.
Remove the UA case in gsm_queue() to process only UA frames with PF bit set
to 1 to abide the standard.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-20-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
gsmtty_write() and gsm_dlci_data_output() properly guard the fifo access.
However, gsm_dlci_close() and gsmtty_flush_buffer() modifies the fifo but
do not guard this.
Add a guard here to prevent race conditions on parallel writes to the fifo.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-17-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
gsm_control_modem() informs the virtual tty that more data can be written
after receiving a control signal octet via modem status command (MSC).
However, gsm_dlci_data() fails to do the same after receiving a control
signal octet from the convergence layer type 2 header.
Add tty_wakeup() in gsm_dlci_data() for convergence layer type 2 to fix
this.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-14-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. The value of the modem status command (MSC) frame
contains an address field, control signal and optional break signal octet.
The address field is encoded as described in chapter 5.2.1.2 with only one
octet (may be extended to more in future versions of the standard). Whereas
the control signal and break signal octet are always one byte each. This is
strange at first glance as it makes the EA bit redundant. However, the same
two octets are also encoded as header in convergence layer type 2 as
described in chapter 5.5.2. No header length field is given and the only
way to test if there is an optional break signal octet is via the EA flag
which extends the control signal octet with a break signal octet. Now it
becomes obvious how the EA bit for those two octets shall be encoded in the
MSC frame. The current implementation treats the signal octet different for
MSC frame and convergence layer type 2 header even though the standard
describes it for both in the same way.
Use the EA bit to encode the signal octets not only in the convergence
layer type 2 header but also in the MSC frame in the same way with either
1 or 2 bytes in case of an optional break signal. Adjust the receiving path
accordingly in gsm_control_modem().
Fixes: 3ac06b905655 ("tty: n_gsm: Fix for modems with brk in modem status control")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-13-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.1 states that each command frame shall
be made up from type, length and value. Looking for example in chapter
5.4.6.3.5 at the description for the encoding of a flow control on command
it becomes obvious, that the type and length field is always present
whereas the value may be zero bytes long. The current implementation omits
the length field if the value is not present. This is wrong.
Correct this by always sending the length in gsm_control_transmit().
So far only the modem status command (MSC) has included a value and encoded
its length directly. Therefore, also change gsmtty_modem_update().
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-12-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_config() fails to limit this range correctly. Furthermore,
gsm_control_retransmit() handles this number incorrectly by performing
N2 - 1 retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix the range check in gsm_config() and the value handling in
gsm_control_send() and gsm_control_retransmit() to comply with 3GPP 27.010.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-11-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In gsm_cleanup_mux() the muxer is closed down and all queues are removed.
However, removing the queues is done without explicit control of the
underlying buffers. Flush those before freeing up our queues to ensure
that all outgoing queues are cleared consistently. Otherwise, a new mux
connection establishment attempt may time out while the underlying tty is
still busy sending out the remaining data from the previous connection.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-10-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current DLCI release order starts with the control channel followed by
the user channels. Reverse this order to keep the control channel open
until all user channels have been released.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.2 states that the maximum frame size
(N1) refers to the length of the information field (i.e. user payload).
However, 'txframe' stores the whole frame including frame header, checksum
and start/end flags. We also need to consider the byte stuffing overhead.
Define constant for the protocol overhead and adjust the 'txframe' size
calculation accordingly to reserve enough space for a complete mux frame
including byte stuffing for advanced option mode. Note that no byte
stuffing is applied to the start and end flag.
Also use MAX_MTU instead of MAX_MRU as this buffer is used for data
transmission.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-8-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The gsm_mux field 'malformed' represents the number of malformed frames
received. However, gsm1_receive() also increases this counter for any out
of frame byte.
Fix this by ignoring out of frame data for the malformed counter.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The frame checksum (FCS) is currently handled in gsm_queue() after
reception of a frame. However, this breaks layering. A workaround with
'received_fcs' was implemented so far.
Furthermore, frames are handled as such even if no end flag was received.
Move FCS calculation from gsm_queue() to gsm0_receive() and gsm1_receive().
Also delay gsm_queue() call there until a full frame was received to fix
both points.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-6-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.5.2 describes that the signal octet in
convergence layer type 2 can be either one or two bytes. The length is
encoded in the EA bit. This is set 1 for the last byte in the sequence.
gsmtty_modem_update() handles this correctly but gsm_dlci_data_output()
fails to set EA to 1. There is no case in which we encode two signal octets
as there is no case in which we send out a break signal.
Therefore, always set the EA bit to 1 for the signal octet to fix this.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Internally, we manage the alive state of the mux channels and mux itself
with the field member 'dead'. This makes it possible to notify the user
if the accessed underlying link is already gone. On the other hand,
however, removing the virtual ttys before terminating the channels may
result in peer messages being received without any internal target. Move
the mux cleanup procedure from gsmld_detach_gsm() to gsmld_close() to fix
this by keeping the virtual ttys open until the mux has been cleaned up.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The active mux instances are managed in the gsm_mux array and via mux_get()
and mux_put() functions separately. This gives a very loose coupling
between the actual instance and the gsm_mux array which manages it. It also
results in unnecessary lockings which makes it prone to failures. And it
creates a race condition if more than the maximum number of mux instances
are requested while the user changes the parameters of an active instance.
The user may loose ownership of the current mux instance in this case.
Fix this by moving the gsm_mux array handling to the mux allocation and
deallocation functions.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.8.2 states that both sides will revert to
the non-multiplexed mode via a close-down message (CLD). The usual program
flow is as following:
- start multiplex mode by sending AT+CMUX to the mobile
- establish the control channel (DLCI 0)
- establish user channels (DLCI >0)
- terminate user channels
- send close-down message (CLD)
- revert to AT protocol (i.e. leave multiplexed mode)
The AT protocol is out of scope of the n_gsm driver. However,
gsm_disconnect() sends CLD if gsm_config() detects that the requested
parameters require the mux protocol to restart. The next immediate action
is to start the mux protocol by opening DLCI 0 again. Any responder side
which handles CLD commands correctly forces us to fail at this point
because AT+CMUX needs to be sent to the mobile to start the mux again.
Therefore, remove the CLD command in this phase and keep both sides in
multiplexed mode.
Remove the gsm_disconnect() function as it become unnecessary and merge the
remaining parts into gsm_cleanup_mux() to handle the termination order and
locking correctly.
Fixes: 71e077915396 ("tty: n_gsm: do not send/receive in ldisc close path")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, only the initiator resets the mux protocol if the user requests
new parameters that are incompatible to those of the current connection.
The responder also needs to reset the multiplexer if the new parameter set
requires this. Otherwise, we end up with an inconsistent parameter set
between initiator and responder.
Revert the old behavior to inform the peer upon an incompatible parameter
set change from the user on the responder side by re-establishing the mux
protocol in such case.
Fixes: 509067bbd264 ("tty: n_gsm: Delete gsm_disconnect when config requester")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fix from Greg KH:
"This is a single serial driver fix for a build issue that showed up
due to changes that came in through the tty tree in 5.18-rc1 that were
missed previously. It resolves a build error with the mpc52xx_uart
driver.
It has been in linux-next this week with no reported problems"
* tag 'tty-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: mpc52xx_uart: make rx/tx hooks return unsigned, part II.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fix from Greg KH:
"Here is a single staging driver fix for 5.18-rc2 that resolves an
endian issue for the r8188eu driver. It has been in linux-next all
this week with no reported problems"
* tag 'staging-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Fix PPPoE tag insertion on little endian systems
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are two small driver core changes for 5.18-rc2.
They are the final bits in the removal of the default_attrs field in
struct kobj_type. I had to wait until after 5.18-rc1 for all of the
changes to do this came in through different development trees, and
then one new user snuck in. So this series has two changes:
- removal of the default_attrs field in the powerpc/pseries/vas code.
The change has been acked by the PPC maintainers to come through
this tree
- removal of default_attrs from struct kobj_type now that all
in-kernel users are removed.
This cleans up the kobject code a little bit and removes some
duplicated functionality that confused people (now there is only
one way to do default groups)
Both of these have been in linux-next for all of this week with no
reported problems"
* tag 'driver-core-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: kobj_type: remove default_attrs
powerpc/pseries/vas: use default_groups in kobj_type
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fix from Greg KH:
"A single driver fix. It resolves the build warning issue on 32bit
systems in the habannalabs driver that came in during the 5.18-rc1
merge cycle.
It has been in linux-next for all this week with no reported problems"
* tag 'char-misc-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
habanalabs: Fix test build failures
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix KVM "lost kick" race, where an attempt to pull a vcpu out of the
guest could be lost (or delayed until the next guest exit).
- Disable SCV (system call vectored) when PR KVM guests could be run.
- Fix KVM PR guests using SCV, by disallowing AIL != 0 for KVM PR
guests.
- Add a new KVM CAP to indicate if AIL == 3 is supported.
- Fix a regression when hotplugging a CPU to a memoryless/cpuless node.
- Make virt_addr_valid() stricter for 64-bit Book3E & 32-bit, which
fixes crashes seen due to hardened usercopy.
- Revert a change to max_mapnr which broke HIGHMEM.
Thanks to Christophe Leroy, Fabiano Rosas, Kefeng Wang, Nicholas Piggin,
and Srikar Dronamraju.
* tag 'powerpc-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
Revert "powerpc: Set max_mapnr correctly"
powerpc: Fix virt_addr_valid() for 64-bit Book3E & 32-bit
KVM: PPC: Move kvmhv_on_pseries() into kvm_ppc.h
powerpc/numa: Handle partially initialized numa nodes
powerpc/64: Fix build failure with allyesconfig in book3s_64_entry.S
KVM: PPC: Use KVM_CAP_PPC_AIL_MODE_3
KVM: PPC: Book3S PR: Disallow AIL != 0
KVM: PPC: Book3S PR: Disable SCV when AIL could be disabled
KVM: PPC: Book3S HV P9: Fix "lost kick" race
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of interrupt chip driver fixes:
- A fix for a long standing bug in the ARM GICv3 redistributor
polling which uses the wrong bit number to test.
- Prevent translation of bogus ACPI table entries which map device
interrupts into the IPI space on ARM GICs.
- Don't write into the pending register of ARM GICV4 before the scan
in hardware has completed.
- A set of build and correctness fixes for the Qualcomm MPM driver"
* tag 'irq-urgent-2022-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic, gic-v3: Prevent GSI to SGI translations
irqchip/gic-v3: Fix GICR_CTLR.RWP polling
irqchip/gic-v4: Wait for GICR_VPENDBASER.Dirty to clear before descheduling
irqchip/irq-qcom-mpm: fix return value check in qcom_mpm_init()
irq/qcom-mpm: Fix build error without MAILBOX
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Fix the MSI message data struct definition
- Use local labels in the exception table macros to avoid symbol
conflicts with clang LTO builds
- A couple of fixes to objtool checking of the relatively newly added
SLS and IBT code
- Rename a local var in the WARN* macro machinery to prevent shadowing
* tag 'x86_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/msi: Fix msi message data shadow struct
x86/extable: Prefer local labels in .set directives
x86,bpf: Avoid IBT objtool warning
objtool: Fix SLS validation for kcov tail-call replacement
objtool: Fix IBT tail-call detection
x86/bug: Prevent shadowing in __WARN_FLAGS
x86/mm/tlb: Revert retpoline avoidance approach
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- A couple of fixes to cgroup-related handling of perf events
- A couple of fixes to event encoding on Sapphire Rapids
- Pass event caps of inherited events so that perf doesn't fail wrongly
at fork()
- Add support for a new Raptor Lake CPU
* tag 'perf_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Always set cpuctx cgrp when enable cgroup event
perf/core: Fix perf_cgroup_switch()
perf/core: Use perf_cgroup_info->active to check if cgroup is active
perf/core: Don't pass task around when ctx sched in
perf/x86/intel: Update the FRONTEND MSR mask on Sapphire Rapids
perf/x86/intel: Don't extend the pseudo-encoding to GP counters
perf/core: Inherit event_caps
perf/x86/uncore: Add Raptor Lake uncore support
perf/x86/msr: Add Raptor Lake CPU support
perf/x86/cstate: Add Raptor Lake support
perf/x86: Add Intel Raptor Lake support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Borislav Petkov:
- Allow the compiler to optimize away unused percpu accesses and change
the local_lock_* macros back to inline functions
- A couple of fixes to static call insn patching
* tag 'locking_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "mm/page_alloc: mark pagesets as __maybe_unused"
Revert "locking/local_lock: Make the empty local_lock_*() function a macro."
x86/percpu: Remove volatile from arch_raw_cpu_ptr().
static_call: Remove __DEFINE_STATIC_CALL macro
static_call: Properly initialise DEFINE_STATIC_CALL_RET0()
static_call: Don't make __static_call_return0 static
x86,static_call: Fix __static_call_return0 for i386
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Borislav Petkov:
- Use the correct static key checking primitive on the IRQ exit path
- Two fixes for the new forceidle balancer
* tag 'sched_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
entry: Fix compile error in dynamic_irqentry_exit_cond_resched()
sched: Teach the forced-newidle balancer about CPU affinity limitation.
sched/core: Fix forceidle balancing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix the clang command line option probing and remove some options to
filter out, fixing the build with the latest clang versions
- Fix 'perf bench' futex and epoll benchmarks to deal with machines
with more than 1K CPUs
- Fix 'perf test tsc' error message when not supported
- Remap perf ring buffer if there is no space for event, fixing perf
usage in 32-bit ChromeOS
- Drop objdump stderr to avoid getting stuck waiting for stdout output
in 'perf annotate'
- Fix up garbled output by now showing unwind error messages when
augmenting frame in best effort mode
- Fix perf's libperf_print callback, use the va_args eprintf() variant
- Sync vhost and arm64 cputype headers with the kernel sources
- Fix 'perf report --mem-mode' with ARM SPE
- Add missing external commands ('iiostat', etc) to 'perf --list-cmds'
* tag 'perf-tools-fixes-for-v5.18-2022-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf annotate: Drop objdump stderr to avoid getting stuck waiting for stdout output
perf tools: Add external commands to list-cmds
perf docs: Add perf-iostat link to manpages
perf session: Remap buf if there is no space for event
perf bench: Fix epoll bench to correct usage of affinity for machines with #CPUs > 1K
perf bench: Fix futex bench to correct usage of affinity for machines with #CPUs > 1K
perf tools: Fix perf's libperf_print callback
perf: arm-spe: Fix perf report --mem-mode
perf unwind: Don't show unwind error messages when augmenting frame pointer stack
tools headers arm64: Sync arm64's cputype.h with the kernel sources
perf test tsc: Fix error message when not supported
perf build: Don't use -ffat-lto-objects in the python feature test when building with clang-13
perf python: Fix probing for some clang command line options
tools build: Filter out options and warnings not supported by clang
tools build: Use $(shell ) instead of `` to get embedded libperl's ccopts
tools include UAPI: Sync linux/vhost.h with the kernel sources
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull cxl and nvdimm fixes from Dan Williams:
- Fix a compile error in the nvdimm unit tests
- Fix a shadowed variable warning in the CXL PCI driver
* tag 'cxl+nvdimm-for-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
cxl/pci: Drop shadowed variable
tools/testing/nvdimm: Fix security_init() symbol collision
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
- fix a race condition with consumers accessing the fields of GPIO IRQ
chips before they're fully initialized
* tag 'gpio-fixes-for-v5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: Restrict usage of GPIO chip irq members before initialization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Fix GICv3 polling for RWP in redistributors
- Reject ACPI attempts to use SGIs on GIC/GICv3
- Fix unpredictible behaviour when making a VPE non-resident
with GICv4
- A couple of fixes for the newly merged qcom-mpm driver
Link: https://lore.kernel.org/lkml/20220409094229.267649-1-maz@kernel.org
|
|
output
If objdump writes to stderr it can block waiting for it to be read. As
perf doesn't read stderr then progress stops with perf waiting for
stdout output.
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexandre Truong <alexandre.truong@arm.com>
Cc: Dave Marchevsky <davemarchevsky@fb.com>
Cc: Denis Nikitin <denik@chromium.org>
Cc: German Gomez <german.gomez@arm.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Lexi Shao <shaolexi@huawei.com>
Cc: Li Huafei <lihuafei1@huawei.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin Liška <mliska@suse.cz>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: Remi Bernon <rbernon@codeweavers.com>
Cc: Riccardo Mancini <rickyman7@gmail.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: William Cohen <wcohen@redhat.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lore.kernel.org/lkml/20220407230503.1265036-2-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The `perf --list-cmds` output prints only internal commands, although
there is no reason for that from users' perspective.
Adding the external commands to commands array with NULL function
pointer allows printing all perf commands while not changing the logic
of command handler selection.
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20220404221541.30312-2-mpetlan@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20220404221541.30312-1-mpetlan@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
If a perf event doesn't fit into remaining buffer space return NULL to
remap buf and fetch the event again.
Keep the logic to error out on inadequate input from fuzzing.
This fixes perf failing on ChromeOS (with 32b userspace):
$ perf report -v -i perf.data
...
prefetch_event: head=0x1fffff8 event->header_size=0x30, mmap_size=0x2000000: fuzzed or compressed perf.data?
Error:
failed to process sample
Fixes: 57fc032ad643ffd0 ("perf session: Avoid infinite loop when seeing invalid header.size")
Reviewed-by: James Clark <james.clark@arm.com>
Signed-off-by: Denis Nikitin <denik@chromium.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20220330031130.2152327-1-denik@chromium.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
- add support for new devices (ufs, mvsas)
- a major set of fixes in lpfc
- get rid of a driver specific ioctl in pcmraid
- a major rework of aha152x to get rid of the scsi_pointer.
- minor fixes and obvious changes including several spelling updates.
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
scsi: megaraid_sas: Target with invalid LUN ID is deleted during scan
scsi: ufs: ufshpb: Fix a NULL check on list iterator
scsi: sd: Clean up gendisk if device_add_disk() failed
scsi: message: fusion: Remove redundant variable dmp
scsi: mvsas: Add PCI ID of RocketRaid 2640
scsi: sd: sd_read_cpr() requires VPD pages
scsi: mpt3sas: Fail reset operation if config request timed out
scsi: sym53c500_cs: Stop using struct scsi_pointer
scsi: ufs: ufs-pci: Add support for Intel MTL
scsi: mpt3sas: Fix mpt3sas_check_same_4gb_region() kdoc comment
scsi: scsi_debug: Fix sdebug_blk_mq_poll() in_use_bm bitmap use
scsi: bnx2i: Fix spelling mistake "mis-match" -> "mismatch"
scsi: bnx2fc: Fix spelling mistake "mis-match" -> "mismatch"
scsi: zorro7xx: Fix a resource leak in zorro7xx_remove_one()
scsi: aic7xxx: Use standard PCI subsystem, subdevice defines
scsi: ufs: qcom: Drop custom Android boot parameters
scsi: core: sysfs: Remove comments that conflict with the actual logic
scsi: hisi_sas: Remove stray fallthrough annotation
scsi: virtio-scsi: Eliminate anonymous module_init & module_exit
scsi: isci: Fix spelling mistake "doesnt" -> "doesn't"
...
|
|
#CPUs > 1K
The 'perf bench epoll' testcase fails on systems with more than 1K CPUs.
Testcase: perf bench epoll all
Result snippet:
<<>>
Run summary [PID 106497]: 1399 threads monitoring on 64 file-descriptors for 8 secs.
perf: pthread_create: No such file or directory
<<>>
In epoll benchmarks (ctl, wait) pthread_create is invoked in do_threads
from respective bench_epoll_* function. Though the logs shows direct
failure from pthread_create, the actual failure is from
"sched_setaffinity" returning EINVAL (invalid argument).
This happens because the default mask size in glibc is 1024. To overcome
this 1024 CPUs mask size limitation of cpu_set_t, change the mask size
using the CPU_*_S macros.
Patch addresses this by fixing all the epoll benchmarks to use CPU_ALLOC
to allocate cpumask, CPU_ALLOC_SIZE for size, and CPU_SET_S to set the
mask.
Reported-by: Disha Goel <disgoel@linux.vnet.ibm.com>
Signed-off-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Tested-by: Disha Goel <disgoel@linux.vnet.ibm.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nageswara R Sastry <rnsastry@linux.ibm.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20220406175113.87881-3-atrajeev@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
#CPUs > 1K
The 'perf bench futex' testcase fails on systems with more than 1K CPUs.
Testcase: perf bench futex all
Failure snippet:
<<>>Running futex/hash benchmark...
perf: pthread_create: No such file or directory
<<>>
All the futex benchmarks (ie hash, lock-api, requeue, wake,
wake-parallel), pthread_create is invoked in respective bench_futex_*
function. Though the logs shows direct failure from pthread_create,
strace logs showed that actual failure is from "sched_setaffinity"
returning EINVAL (invalid argument).
This happens because the default mask size in glibc is 1024. To overcome
this 1024 CPUs mask size limitation of cpu_set_t, change the mask size
using the CPU_*_S macros.
Patch addresses this by fixing all the futex benchmarks to use CPU_ALLOC
to allocate cpumask, CPU_ALLOC_SIZE for size, and CPU_SET_S to set the
mask.
Reported-by: Disha Goel <disgoel@linux.vnet.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Tested-by: Disha Goel <disgoel@linux.vnet.ibm.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nageswara R Sastry <rnsastry@linux.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20220406175113.87881-2-atrajeev@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
eprintf() does not expect va_list as the type of the 4th parameter.
Use veprintf() because it does.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 428dab813a56ce94 ("libperf: Merge libperf_set_print() into libperf_init()")
Cc: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20220408132625.2451452-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Since commit bb30acae4c4dacfa ("perf report: Bail out --mem-mode if mem
info is not available") "perf mem report" and "perf report --mem-mode"
don't allow opening the file unless one of the events has
PERF_SAMPLE_DATA_SRC set.
SPE doesn't have this set even though synthetic memory data is generated
after it is decoded. Fix this issue by setting DATA_SRC on SPE events.
This has no effect on the data collected because the SPE driver doesn't
do anything with that flag and doesn't generate samples.
Fixes: bb30acae4c4dacfa ("perf report: Bail out --mem-mode if mem info is not available")
Signed-off-by: James Clark <james.clark@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: German Gomez <german.gomez@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20220408144056.1955535-1-james.clark@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
