| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch adds support to 8-channel DMA engine, thus the driver works for both
the new 8-channel and the legacy 4-channel DMA engines.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Freescale QorIQ T4 and B4 introduce new 8-channel DMA engines, this patch adds
the device tree nodes for them.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch updates the discription of each type of DMA controller and its
channels, it is preparation for adding another new DMA controller binding, it
also fixes some defects of indent for text alignment at the same time.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This resolves a number of warnings such as the below when building with
64-bit dma_addr_t on arm:
drivers/dma/imx-sdma.c:1092:3: warning: format '%x' expects argument of
type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
..by upcasting to u64 and using %llx.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This resolves a number of warnings such as the below when building with
64-bit dma_addr_t on arm:
drivers/dma/ipu/ipu_idmac.c:1235:2: warning: format '%x' expects argument
of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
..by upcasting to u64 and using %llx.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
fixing of freeing descriptor memory was applied twice, so remove the one
duplicate
Reported-by: Wing-Keung Wang <wingkeung.wang@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Return code of pm_runtime_get_sync() > 0 is not an error and may happen.
Noticed during rmmod & modprobe testing.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Most of the logic here is try and error since what actually happens does
not match the trm or I miss read it.
My first assumption was that the queue on which the tear-down descriptor
completes (their own complete queue vs "active descriptor" complete
queue) depends on the transfer direction. This seems not to be true
because I manage to trigger
| WARN_ON(c->desc_phys != desc_phys);
and the other few were fine means the tear-down descriptor was valid but
on different queue.
This patch changes the logic here to look on both queues for the
descriptor.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Use cppi41_pop_desc() when appropriate instead of open-coding the same
functionality again. That makes the code more readable. The function has
to be moved some lines up for this change.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
With active users over suspend/resume cycles, it turns out that
more registers, in particular DMA_TDFDQ and RXHPCRA0, have to be
restored on resume.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Using the PaRAM configuration function that we split for reuse by the
different DMA types, we implement Cyclic DMA support.
For the cyclic case, we pass different configuration parameters to this
function, and handle all the Cyclic-specific functionality separately.
Callbacks to the DMA users are handled using vchan_cyclic_callback in
the virt-dma layer. Linking is handled the same way as the slave SG case
except for the last slot where we link it back to the first one in a
cyclic fashion.
For continuity, we check for cases where no.of periods is great than the
MAX number of slots the driver can allocate for a particular descriptor
and error out on such cases.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
|
|
|
|
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d0631001288a5974afc0b2a5f568bcdecb4d)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
drivers/dma/imx-dma.c:575:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t'
drivers/dma/imx-dma.c:575:3: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t'
drivers/dma/imx-dma.c:589:4: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t'
drivers/dma/imx-dma.c:599:4: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t'
drivers/dma/imx-dma.c:929:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t'
drivers/dma/imx-dma.c:929:2: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t'
drivers/dma/imx-dma.c:959:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t'
drivers/dma/imx-dma.c:959:2: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t'
We can't use the %pa format for these because this relates to phys_addr_t,
and dma_addr_t can be a different size. So, fix these by converting them
to %llx and casting the dma_addr_t to always be unsigned long long.
While we're here, also use %zu for size_t.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
edma header defines DMA_COMPLETE, this causes issues as commit adfedd9a32e4 move
DMA_SUCCESS to DMA_COMPLETE. edma should properly namespace its defines and
needs a future fix
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
|
|
Conflicts:
drivers/dma/edma.c
Moved the memory leak fix post merge
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"This is a 2-line patch to save the CPU register which holds our task
thread info pointer before calling a firmware function and then to
restore it again afterwards.
This is necessary because on some 64bit machines the high-order 32bits
are being clobbered by the firmware call, and thus we failed to bring
up secondary CPUs (and instead crashed the kernel) in some situations
eg if we had more than 4GB RAM. This patch fixes a bug which has been
since ever in the parisc linux kernel and which prevented some people
to use a 64bit kernel"
* 'parisc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Do not crash 64bit SMP kernels on machines with >= 4GB RAM
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"This tree contains a clockevents regression fix for certain ARM
subarchitectures"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Sanitize ticks to nsec conversion
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"The tree contains three fixes:
- Two tooling fixes
- Reversal of the new 'MMAP2' extended mmap record ABI, introduced in
this merge window. (Patches were proposed to fix it but it was all
a bit late and we felt it's safer to just delay the ABI one more
kernel release and do it right)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Disable PERF_RECORD_MMAP2 support
perf scripting perl: Fix build error on Fedora 12
perf probe: Fix to initialize fname always before use it
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
"This tree fixes a boot crash in CONFIG_DEBUG_MUTEXES=y kernels, on
kernels built with GCC 3.x (there are still such distros)"
Side note: it's not just a fix for old gcc versions, it's also removing
an incredibly broken/subtle check that LLVM had issues with, and that
made no sense.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mutex: Avoid gcc version dependent __builtin_constant_p() usage
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target pending fixes for v3.12-rc7.
This includes a number of EXTENDED_COPY related fixes as a result of
Thomas and Doug's continuing testing and feedback.
Also included is an important vhost/scsi fix that addresses a long
standing issue where the 'write' parameter for get_user_pages_fast()
was incorrectly set for virtio-scsi WRITEs -> DMA_TO_DEVICE, and not
for virtio-scsi READs -> DMA_FROM_DEVICE.
This resulted in random userspace segfaults and other unpleasantness
on KVM host, and unfortunately has been an issue since the initial
merge of vhost/scsi in v3.6. This patch is CC'ed to stable, along
with two other less critical items"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
vhost/scsi: Fix incorrect usage of get_user_pages_fast write parameter
target/pscsi: fix return value check
target: Fail XCOPY for non matching source + destination block_size
target: Generate failure for XCOPY I/O with non-zero scsi_status
target: Add missing XCOPY I/O operation sense_buffer
iser-target: check device before dereferencing its variable
target: Return an error for WRITE SAME with ANCHOR==1
target: Fix assignment of LUN in tracepoints
target: Reject EXTENDED_COPY when emulate_3pc is disabled
target: Allow non zero ListID in EXTENDED_COPY parameter list
target: Make target_do_xcopy failures return INVALID_PARAMETER_LIST
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the late fixes pull request for dmaengine while you fly back
from KS.
We have a new dmaengine ML hosted by vger so a patch for that along
with addition of Dave as driver mainatainer for ioat. Other fixes are
memeory leak fixes on edma driver, small fixes on rcar-hpbdma driver
by Sergei"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: edma: fix another memory leak
dma: edma: Fix memory leak
MAINTAINERS: add to ioatdma maintainer list
MAINTAINERS: add the new dmaengine mailing list
|
|
Since the beginning of the parisc-linux port, sometimes 64bit SMP kernels were
not able to bring up other CPUs than the monarch CPU and instead crashed the
kernel. The reason was unclear, esp. since it involved various machines (e.g.
J5600, J6750 and SuperDome). Testing showed, that those crashes didn't happened
when less than 4GB were installed, or if a 32bit Linux kernel was booted.
In the end, the fix for those SMP problems is trivial:
During the early phase of the initialization of the CPUs, including the monarch
CPU, the PDC_PSW firmware function to enable WIDE (=64bit) mode is called.
It's documented that this firmware function may clobber various registers, and
one one of those possibly clobbered registers is %cr30 which holds the task
thread info pointer.
Now, if %cr30 would always have been clobbered, then this bug would have been
detected much earlier. But lots of testing finally showed, that - at least for
%cr30 - on some machines only the upper 32bits of the 64bit register suddenly
turned zero after the firmware call.
So, after finding the root cause, the explanation for the various crashes
became clear:
- On 32bit SMP Linux kernels all upper 32bit were zero, so we didn't faced this
problem.
- Monarch CPUs in 64bit mode always booted sucessfully, because the inital task
thread info pointer was below 4GB.
- Secondary CPUs booted sucessfully on machines with less than 4GB RAM because
the upper 32bit were zero anyay.
- Secondary CPus failed to boot if we had more than 4GB RAM and the task thread
info pointer was located above the 4GB boundary.
Finally, the patch to fix this problem is trivial by saving the %cr30 register
before the firmware call and restoring it afterwards.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 2.6.12+
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from
"These fix two bugs in the intel_pstate driver, a hibernate bug leading
to nasty resume failures sometimes and acpi-cpufreq initialization bug
that causes problems to happen during module unload when intel_pstate
is in use.
Specifics:
- Fix for rounding errors in intel_pstate causing CPU utilization to
be underestimated from Brennan Shacklett.
- intel_pstate fix to always use the correct max pstate value when
computing the min pstate from Dirk Brandewie.
- Hibernation fix for deadlocking resume in cases when the probing of
the device containing the image is deferred from Russ Dill.
- acpi-cpufreq fix to prevent the module from staying in memory when
the driver cannot be registered and then attempting to unregister
things that have never been registered on exit"
* tag 'pm+acpi-3.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
acpi-cpufreq: Fail initialization if driver cannot be registered
PM / hibernate: Move software_resume to late_initcall_sync
intel_pstate: Correct calculation of min pstate value
intel_pstate: Improve accuracy by not truncating until final result
|
|
Pull final mtd fixes from Brian Norris:
"A few more last-minute regression fixes, prepared jointly by me and
David Woodhouse:
- Revert pxa3xx to its old name to avoid breaking existing
'mtdparts=' boot strings.
- Return GPMI NAND to its legacy ECC layout for backwards
compatibility. We will revisit this in 3.13.
A note from David on the latter fix: 'This leaves a harmless cosmetic
warning about an unused function. At this point in the cycle I really
don't care.'"
* tag 'for-linus-20131025' of git://git.infradead.org/linux-mtd:
mtd: gpmi: fix ECC regression
mtd: nand: pxa3xx: Fix registered MTD name
|
|
This patch addresses a long-standing bug where the get_user_pages_fast()
write parameter used for setting the underlying page table entry permission
bits was incorrectly set to write=1 for data_direction=DMA_TO_DEVICE, and
passed into get_user_pages_fast() via vhost_scsi_map_iov_to_sgl().
However, this parameter is intended to signal WRITEs to pinned userspace
PTEs for the virtio-scsi DMA_FROM_DEVICE -> READ payload case, and *not*
for the virtio-scsi DMA_TO_DEVICE -> WRITE payload case.
This bug would manifest itself as random process segmentation faults on
KVM host after repeated vhost starts + stops and/or with lots of vhost
endpoints + LUNs.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Asias He <asias@redhat.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
In case of error, the function scsi_host_lookup() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes (try two) from Al Viro:
"nfsd performance regression fix + seq_file lseek(2) fix"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
seq_file: always update file->f_pos in seq_lseek()
nfsd regression since delayed fput()
|
|
The "legacy" ECC layout used until 3.12-rc1 uses all the OOB area by
computing the ECC strength and ECC step size ourselves.
Commit 2febcdf84b ("mtd: gpmi: set the BCHs geometry with the ecc info")
makes the driver use the ECC info (ECC strength and ECC step size)
provided by the MTD code, and creates a different NAND ECC layout
for the BCH, and use the new ECC layout. This causes a regression:
We can not mount the ubifs which was created by the old NAND ECC layout.
This patch fixes this issue by reverting to the legacy ECC layout.
We will probably introduce a new device-tree property to indicate that
the new ECC layout can be used. For now though, for the imminent 3.12
release, we just unconditionally revert to the 3.11 behaviour.
This leaves a harmless cosmetic warning about an unused function. At
this point in the cycle I really don't care.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
|
|
This issue was first pointed out by Jiaxing Wang several months ago, but no
further comments:
https://lkml.org/lkml/2013/6/29/41
As we know pread() does not change f_pos, so after pread(), file->f_pos
and m->read_pos become different. And seq_lseek() does not update file->f_pos
if offset equals to m->read_pos, so after pread() and seq_lseek()(lseek to
m->read_pos), then a subsequent read may read from a wrong position, the
following program produces the problem:
char str1[32] = { 0 };
char str2[32] = { 0 };
int poffset = 10;
int count = 20;
/*open any seq file*/
int fd = open("/proc/modules", O_RDONLY);
pread(fd, str1, count, poffset);
printf("pread:%s\n", str1);
/*seek to where m->read_pos is*/
lseek(fd, poffset+count, SEEK_SET);
/*supposed to read from poffset+count, but this read from position 0*/
read(fd, str2, count);
printf("read:%s\n", str2);
out put:
pread:
ck_netbios_ns 12665
read:
nf_conntrack_netbios
/proc/modules:
nf_conntrack_netbios_ns 12665 0 - Live 0xffffffffa038b000
nf_conntrack_broadcast 12589 1 nf_conntrack_netbios_ns, Live 0xffffffffa0386000
So we always update file->f_pos to offset in seq_lseek() to fix this issue.
Signed-off-by: Jiaxing Wang <hello.wjx@gmail.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Make acpi_cpufreq_init() return error codes when the driver cannot be
registered so that the module doesn't stay useless in memory and so
that acpi_cpufreq_exit() doesn't attempt to unregister things that
have never been registered when the module is unloaded.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"There's really only one bugfix in this branch, which is a fix for
timers on the integrator platform. Since Linus Walleij is
resurrecting support for the platform it seems valuable to get the fix
into 3.12 even though the regression has been around a while.
The rest are a handful of maintainers updates. If you prefer to hold
those until 3.13 then just merge the first patch on the branch which
is the fix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add maintainers entry for Rockchip SoCs
MAINTAINERS: Tegra updates, and driver ownership
MAINTAINERS: ARM: mvebu: add Sebastian Hesselbarth
ARM: integrator: deactivate timer0 on the Integrator/CP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
"Two important fixes
- Fix long standing memory leak in the (rarely used) public key
support
- Fix large file corruption on 32 bit architectures"
* tag 'ecryptfs-3.12-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: fix 32 bit corruption issue
ecryptfs: Fix memory leakage in keystore.c
|
|
after all the users are converted
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
