| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The za-fork test does not output a newline when reporting the result of
the one test it runs, causing the counts printed by kselftest to be
included in the test name. Add the newline.
Fixes: 266679ffd867 ("kselftest/arm64: Convert za-fork to use kselftest.h")
Cc: <stable@vger.kernel.org> # 6.4.x
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20231116-arm64-fix-za-fork-output-v1-1-42c03d4f5759@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Raju Rangoju says:
====================
amd-xgbe: fixes to handle corner-cases
This series include bug fixes to amd-xgbe driver.
====================
Link: https://lore.kernel.org/r/20231121191435.4049995-1-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
xgbe_get_link_ksettings() does not propagate correct speed and duplex
information to ethtool during cable unplug. Due to which ethtool reports
incorrect values for speed and duplex.
Address this by propagating correct information.
Fixes: 7c12aa08779c ("amd-xgbe: Move the PHY support into amd-xgbe")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The existing implementation uses software logic to accumulate tx
completions until the specified time (1ms) is met and then poll them.
However, there exists a tiny gap which leads to a race between
resetting and checking the tx_activate flag. Due to this the tx
completions are not reported to upper layer and tx queue timeout
kicks-in restarting the device.
To address this, introduce a tx cleanup mechanism as part of the
periodic maintenance process.
Fixes: c5aa9e3b8156 ("amd-xgbe: Initial AMD 10GbE platform driver")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Force the mode change for SFI in Fixed PHY configurations. Fixed PHY
configurations needs PLL to be enabled while doing mode set. When the
SFP module isn't connected during boot, driver assumes AN is ON and
attempts auto-negotiation. However, if the connected SFP comes up in
Fixed PHY configuration the link will not come up as PLL isn't enabled
while the initial mode set command is issued. So, force the mode change
for SFI in Fixed PHY configuration to fix link issues.
Fixes: e57f7a3feaef ("amd-xgbe: Prepare for working with more than one type of phy")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fix a possible misalignment between page_pool stats and tx xdp_stats
reported in veth_get_ethtool_stats routine.
The issue can be reproduced configuring the veth pair with the
following tx/rx queues:
$ip link add v0 numtxqueues 2 numrxqueues 4 type veth peer name v1 \
numtxqueues 1 numrxqueues 1
and loading a simple XDP program on v0 that just returns XDP_PASS.
In this case on v0 the page_pool stats overwrites tx xdp_stats for queue 1.
Fix the issue incrementing pp_idx of dev->real_num_tx_queues * VETH_TQ_STATS_LEN
since we always report xdp_stats for all tx queues in ethtool.
Fixes: 4fc418053ec7 ("net: veth: add page_pool stats")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/c5b5d0485016836448453f12846c7c4ab75b094a.1700593593.git.lorenzo@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
queue than its PF
It is possible to add a ntuple rule which would like to direct packet to
a VF whose number of queues are greater/less than its PF's queue numbers.
For example a PF can have 2 Rx queues but a VF created on that PF can have
8 Rx queues. As of today, ntuple rule will reject rule because it is
checking the requested queue number against PF's number of Rx queues.
As a part of this fix if the action of a ntuple rule is to move a packet
to a VF's queue then the check is removed. Also, a debug information is
printed to aware user that it is user's responsibility to cross check if
the requested queue number on that VF is a valid one.
Fixes: f0a1913f8a6f ("octeontx2-pf: Add support for ethtool ntuple filters")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231121165624.3664182-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
xen_vcpu_info is a percpu area than needs to be mapped by Xen.
Currently, it could cross a page boundary resulting in Xen being unable
to map it:
[ 0.567318] kernel BUG at arch/arm64/xen/../../arm/xen/enlighten.c:164!
[ 0.574002] Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP
Fix the issue by using __alloc_percpu and requesting alignment for the
memory allocation.
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2311221501340.2053963@ubuntu-linux-20-04-desktop
Fixes: 24d5373dda7c ("arm/xen: Use alloc_percpu rather than __alloc_percpu")
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Interface 4 is used by for QMI interface in stock firmware of MF28D, the
router which uses MF290 modem. Rebind it to qmi_wwan after freeing it up
from option driver.
The proper configuration is:
Interface mapping is:
0: QCDM, 1: (unknown), 2: AT (PCUI), 2: AT (Modem), 4: QMI
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=0189 Rev= 0.00
S: Manufacturer=ZTE, Incorporated
S: Product=ZTE LTE Technologies MSM
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://lore.kernel.org/r/20231117231918.100278-3-lech.perczak@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When CONFIG_NVME_KEYRING is enabled as a loadable module, but the TCP
host code is built-in, it fails to link:
arm-linux-gnueabi-ld: drivers/nvme/host/tcp.o: in function `nvme_tcp_setup_ctrl':
tcp.c:(.text+0x1940): undefined reference to `nvme_tls_psk_default'
The problem is that the compile-time conditionals are inconsistent here,
using a mix of #ifdef CONFIG_NVME_TCP_TLS, IS_ENABLED(CONFIG_NVME_TCP_TLS)
and IS_ENABLED(CONFIG_NVME_KEYRING) checks, with CONFIG_NVME_KEYRING
controlling whether the implementation is actually built.
Change it to use IS_ENABLED(CONFIG_NVME_KEYRING) checks consistently,
which should help readability and make it less error-prone. Combining
it with the check for the ctrl->opts->tls flag lets the compiler drop
all the TLS code in configurations without this feature, which also
helps runtime behavior in addition to avoiding the link failure.
To make it possible for the compiler to build the dead code, both
the tls_handshake_timeout variable and the TLS specific members
of nvme_tcp_queue need to be moved out of the #ifdef block as well,
but at least the former of these gets optimized out again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231122224719.4042108-4-arnd@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When the NVME target code is built-in but its TCP frontend is a loadable
module, enabling keyring support causes a link failure:
x86_64-linux-ld: vmlinux.o: in function `nvmet_ports_make':
configfs.c:(.text+0x100a211): undefined reference to `nvme_keyring_id'
The problem is that CONFIG_NVME_TARGET_TCP_TLS is a 'bool' symbol that
depends on the tristate CONFIG_NVME_TARGET_TCP, so any 'select' from
it inherits the state of the tristate symbol rather than the intended
CONFIG_NVME_TARGET one that contains the actual call.
The same thing is true for CONFIG_KEYS, which itself is required for
NVME_KEYRING.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231122224719.4042108-3-arnd@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In configurations without CONFIG_NVME_TARGET_TCP_TLS, the keyring
code might not be available, or using it will result in a runtime
failure:
x86_64-linux-ld: vmlinux.o: in function `nvmet_ports_make':
configfs.c:(.text+0x100a211): undefined reference to `nvme_keyring_id'
Add a check to ensure we only check the keyring if there is a chance
of it being used, which avoids both the runtime and link-time
problems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231122224719.4042108-2-arnd@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In order to make sure I get CC'd on tracing changes for which my input
would be relevant, add my name as reviewer of the TRACING subsystem.
Link: https://lore.kernel.org/linux-trace-kernel/20231115155018.8236-1-mathieu.desnoyers@efficios.com
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Since the locking of the parent->d_inode has been moved outside the
creation of the files and directories (as it use to be locked via a
conditional), add a WARN_ON_ONCE() to the case that it's not locked.
Link: https://lkml.kernel.org/r/20231121231112.853962542@goodmis.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
The eventfs directory is dynamically created via the meta data supplied by
the existing trace events. All files and directories in eventfs has a
parent. Do not allow NULL to be passed into eventfs_start_creating() as
the parent because that should never happen. Warn if it does.
Link: https://lkml.kernel.org/r/20231121231112.693841807@goodmis.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
The both create_file_dentry() and create_dir_dentry() takes a boolean
parameter "lookup", as on lookup the inode_lock should already be taken,
but for dcache_dir_open_wrapper() it is not taken.
There's no reason that the dcache_dir_open_wrapper() can't take the
inode_lock before calling these functions. In fact, it's better if it
does, as the lock can be held throughout both directory and file
creations.
This also simplifies the code, and possibly prevents unexpected race
conditions when the lock is released.
Link: https://lkml.kernel.org/r/20231121231112.528544825@goodmis.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: 5790b1fb3d672 ("eventfs: Remove eventfs_file and just use eventfs_inode")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
If memory reclaim happens, it can reclaim file system pages. The file
system pages from eventfs may take the eventfs_mutex on reclaim. This
means that allocation while holding the eventfs_mutex must not call into
filesystem reclaim. A lockdep splat uncovered this.
Link: https://lkml.kernel.org/r/20231121231112.373501894@goodmis.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: 28e12c09f5aa0 ("eventfs: Save ownership and mode")
Fixes: 5790b1fb3d672 ("eventfs: Remove eventfs_file and just use eventfs_inode")
Reported-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
When CONFIG_RODATA_FULL_DEFAULT_ENABLED=y, passing "rodata=on" on the
kernel command-line (rather than "rodata=full") should turn off the
"full" behaviour, leaving writable linear aliases of read-only kernel
memory. Unfortunately, the option has no effect in this situation and
the only way to disable the "rodata=full" behaviour is to disable rodata
protection entirely by passing "rodata=off".
Fix this by parsing the "on" and "off" options in the arch code,
additionally enforcing that 'rodata_full' cannot be set without also
setting 'rodata_enabled', allowing us to simplify a couple of checks
in the process.
Fixes: 2e8cff0a0eee ("arm64: fix rodata=full")
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20231117131422.29663-1-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix several build errors, a potential kernel panic, a cpu hotplug
issue and update links in documentations"
* tag 'loongarch-fixes-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
Docs/zh_CN/LoongArch: Update links in LoongArch introduction.rst
Docs/LoongArch: Update links in LoongArch introduction.rst
LoongArch: Implement constant timer shutdown interface
LoongArch: Mark {dmw,tlb}_virt_to_page() exports as non-GPL
LoongArch: Silence the boot warning about 'nokaslr'
LoongArch: Add __percpu annotation for __percpu_read()/__percpu_write()
LoongArch: Record pc instead of offset in la_abs relocation
LoongArch: Explicitly set -fdirect-access-external-data for vmlinux
LoongArch: Add dependency between vmlinuz.efi and vmlinux.efi
|
|
When we're recovering ondisk quota records from the log, we need to
validate the recovered buffer contents before writing them to disk.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
|
|
Since the introduction of xfs_dqblk in V5, xfs really ought to find the
dqblk pointer from the dquot buffer, then compute the xfs_disk_dquot
pointer from the dqblk pointer. Fix the open-coded xfs_buf_offset calls
and do the type checking in the correct order.
Note that this has made no practical difference since the start of the
xfs_disk_dquot is coincident with the start of the xfs_dqblk.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- One fix for the KVP daemon (Ani Sinha)
- Fix for the detection of E820_TYPE_PRAM in a Gen2 VM (Saurabh Sengar)
- Micro-optimization for hv_nmi_unknown() (Uros Bizjak)
* tag 'hyperv-fixes-signed-20231121' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Use atomic_try_cmpxchg() to micro-optimize hv_nmi_unknown()
x86/hyperv: Fix the detection of E820_TYPE_PRAM in a Gen2 VM
hv/hv_kvp_daemon: Some small fixes for handling NM keyfiles
|
|
We really don't want to do atomic_read() or anything like that, since we
already have the value, not the lock. The whole point of this is that
we've loaded the lock from memory, and we want to check whether the
value we loaded was a locked one or not.
The main use of this is the lockref code, which loads both the lock and
the reference count in one atomic operation, and then works on that
combined value. With the atomic_read(), the compiler would pointlessly
spill the value to the stack, in order to then be able to read it back
"atomically".
This is the qspinlock version of commit c6f4a9002252 ("asm-generic:
ticket-lock: Optimize arch_spin_value_unlocked()") which fixed this same
bug for ticket locks.
Cc: Guo Ren <guoren@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Waiman Long <longman@redhat.com>
Link: https://lore.kernel.org/all/CAHk-=whNRv0v6kQiV5QO6DJhjH4KEL36vWQ6Re8Csrnh4zbRkQ@mail.gmail.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull NVMe fixes from Keith:
"nvme fixes for Linux 6.7
- TCP TLS fixes (Hannes)
- Authentifaction fixes (Mark, Hannes)
- Properly terminate target names (Christoph)"
* tag 'nvme-6.7-2023-11-22' of git://git.infradead.org/nvme:
nvme: move nvme_stop_keep_alive() back to original position
nvmet-tcp: always initialize tls_handshake_tmo_work
nvmet: nul-terminate the NQNs passed in the connect command
nvme: blank out authentication fabrics options if not configured
nvme: catch errors from nvme_configure_metadata()
nvme-tcp: only evaluate 'tls' option if TLS is selected
nvme-auth: set explanation code for failure2 msgs
nvme-auth: unlock mutex in one place only
|
|
Stopping keep-alive not only stops the keep-alive workqueue,
but also needs to be synchronized with I/O termination as we
must not send a keep-alive command after all I/O had been
terminated.
So to avoid any regressions move the call to stop_keep_alive()
back to its original position and ensure that keep-alive is
correctly stopped failing to setup the admin queue.
Fixes: 4733b65d82bd ("nvme: start keep-alive after admin queue setup")
Suggested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
For some unknown reason the regular expression for checkstack only matches
three digit numbers starting with the number "3", or any higher
number. Which means that it skips any stack sizes smaller than 304
bytes. This makes the checkstack script a bit less useful than it could be.
Change the script to match any number. To be filtered out stack sizes
can be configured with the min_stack variable, which omits any stack
frame sizes smaller than 100 bytes by default.
Tested-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
In the meantime hopefully most people got used to forward
declarations, therefore remove the explanation.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Add missing IPL_TYPE_ECKD_DUMP case to ipl_init() creating
ECKD ipl device attribute group similar to IPL_TYPE_ECKD case.
Commit e2d2a2968f2a ("s390/ipl: add eckd dump support") should
have had it from the beginning.
Fixes: e2d2a2968f2a ("s390/ipl: add eckd dump support")
Signed-off-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Setting event::hw.last_tag to zero is not necessary. The memory
for each event is dynamically allocated by the kernel common code and
initialized to zero already. Remove this unnecessary assignment.
Move the comment to function paicrypt_start() for clarification.
Suggested-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Make sure to free the "urs" platform device, which is created for some
ACPI platforms, on probe errors and on driver unbind.
Compile-tested only.
Fixes: c25c210f590e ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20231117173650.21161-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to remove the software node also on (ACPI) probe errors to
avoid leaking the underlying resources.
Note that the software node is only used for ACPI probe so the driver
unbind tear down is updated to match probe.
Fixes: 8dc6e6dd1bee ("usb: dwc3: qcom: Constify the software node")
Cc: stable@vger.kernel.org # 5.12
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231117173650.21161-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver needs to deregister and free the newly allocated dwc3 core
platform device on ACPI probe errors (e.g. probe deferral) and on driver
unbind but instead it leaked those resources while erroneously dropping
a reference to the parent platform device which is still in use.
For OF probing the driver takes a reference to the dwc3 core platform
device which has also always been leaked.
Fix the broken ACPI tear down and make sure to drop the dwc3 core
reference for both OF and ACPI.
Fixes: 8fd95da2cfb5 ("usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()")
Fixes: 2bc02355f8ba ("usb: dwc3: qcom: Add support for booting with ACPI")
Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Lee Jones <lee@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231117173650.21161-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the IRQF_NO_AUTOEN irq flag when requesting the wakeup interrupts
instead of setting it separately.
No functional change intended.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231120161607.7405-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Qualcomm glue driver is overriding the interrupt trigger types
defined by firmware when requesting the wakeup interrupts during probe.
This can lead to a failure to map the DP/DM wakeup interrupts after a
probe deferral as the firmware defined trigger types do not match the
type used for the initial mapping:
irq: type mismatch, failed to map hwirq-14 for interrupt-controller@b220000!
irq: type mismatch, failed to map hwirq-15 for interrupt-controller@b220000!
Fix this by not overriding the firmware provided trigger types when
requesting the wakeup interrupts.
Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231120161607.7405-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DP/DM wakeup interrupts are edge triggered and which edge to trigger
on depends on use-case and whether a Low speed or Full/High speed device
is connected.
Fixes: 3828026c9ec8 ("dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231120161607.7405-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for the Microchip USB5744 USB3.0 and USB2.0 Hub.
The Microchip USB5744 supports two power supplies, one for 1V2 and one
for 3V3. According to the datasheet there is no need for a delay between
power on and reset, so this value is set to 0.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Cc: stable <stable@kernel.org>
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20231113145921.30104-3-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB5744 has two power supplies one for 3V3 and one for 1V2. Add the
second supply to the USB5744 DT binding.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20231113145921.30104-2-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit efa5f1311c4998e9e6317c52bc5ee93b3a0f36df.
I couldn't reproduce the reported issue. What I did, based on a pcap
packet log provided by the reporter:
- Used same chip version (RTL8168h)
- Set MAC address to the one used on the reporters system
- Replayed the EAPOL unicast packet that, according to the reporter,
was filtered out by the mc filter.
The packet was properly received.
Therefore the root cause of the reported issue seems to be somewhere
else. Disabling mc filtering completely for the most common chip
version is a quite big hammer. Therefore revert the change and wait
for further analysis results from the reporter.
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all LJCA chips implement SPI and on chips without SPI reading
the SPI descriptors will timeout.
On laptop models like the Dell Latitude 9420, this is expected behavior
and not an error.
Modify the driver to continue without instantiating a SPI auxbus child,
instead of failing to probe() the whole LJCA chip.
Fixes: acd6199f195d ("usb: Add support for Intel LJCA device")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Wentong Wu <wentong.wu@intel.com>
Link: https://lore.kernel.org/r/20231104175104.38786-1-hdegoede@redhat.com
Link: https://lore.kernel.org/r/20231121203205.223047-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We found a data corruption issue during testing of SMC-R on Redis
applications.
The benchmark has a low probability of reporting a strange error as
shown below.
"Error: Protocol error, got "\xe2" as reply type byte"
Finally, we found that the retrieved error data was as follows:
0xE2 0xD4 0xC3 0xD9 0x04 0x00 0x2C 0x20 0xA6 0x56 0x00 0x16 0x3E 0x0C
0xCB 0x04 0x02 0x01 0x00 0x00 0x20 0x00 0x00 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xE2
It is quite obvious that this is a SMC DECLINE message, which means that
the applications received SMC protocol message.
We found that this was caused by the following situations:
client server
¦ clc proposal
------------->
¦ clc accept
<-------------
¦ clc confirm
------------->
wait llc confirm
send llc confirm
¦failed llc confirm
¦ x------
(after 2s)timeout
wait llc confirm rsp
wait decline
(after 1s) timeout
(after 2s) timeout
¦ decline
-------------->
¦ decline
<--------------
As a result, a decline message was sent in the implementation, and this
message was read from TCP by the already-fallback connection.
This patch double the client timeout as 2x of the server value,
With this simple change, the Decline messages should never cross or
collide (during Confirm link timeout).
This issue requires an immediate solution, since the protocol updates
involve a more long-term solution.
Fixes: 0fb0b02bd6fd ("net/smc: adapt SMC client code to use the LLC flow")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported an memory leak that happens when an skb is add to
send_buff after virtual nci closed.
This patch adds a variable to track if the ndev is running before
handling new skb in send function.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Reported-by: syzbot+6eb09d75211863f15e3e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/lkml/00000000000075472b06007df4fb@google.com
Reviewed-by: Bongsu Jeon
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Honor MagicBook 13 2023 has a touchpad which do not switch to the multitouch
mode until the input mode feature is written by the host. The touchpad do
report the input mode at touchpad(3), while itself working under mouse mode. As
a workaround, it is possible to call MT_QUIRE_FORCE_GET_FEATURE to force set
feature in mt_set_input_mode for such device.
The touchpad reports as BLTP7853, which cannot retrive any useful manufacture
information on the internel by this string at present. As the serial number of
the laptop is GLO-G52, while DMI info reports the laptop serial number as
GLO-GXXX, this workaround should applied to all models which has the GLO-GXXX.
Signed-off-by: Aoba K <nexp_0x17@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Some devices managed by this driver automatically set brightness to 0
before entering a suspended state and reset it back to a default
brightness level after the resume:
this has the effect of having the kernel report wrong brightness
status after a sleep, and on some devices (like the Asus RC71L) that
brightness is the intensity of LEDs directly facing the user.
Fix the above issue by setting back brightness to the level it had
before entering a sleep state.
Signed-off-by: Denis Benato <benato.denis96@gmail.com>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
In the function asus_kbd_set_report the parameter buf is read-only
as it gets copied in a memory portion suitable for USB transfer,
but the parameter is not marked as const: add the missing const and mark
const immutable buffers passed to that function.
Signed-off-by: Denis Benato <benato.denis96@gmail.com>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add support for Fibocom L716-EU module series.
L716-EU is a Fibocom module based on ZTE's V3E/V3T chipset.
Device creates multiple interfaces when connected to PC as follows:
- Network Interface: ECM or RNDIS (set by FW or AT Command)
- ttyUSB0: AT port
- ttyUSB1: Modem port
- ttyUSB2: AT2 port
- ttyUSB3: Trace port for log information
- ADB: ADB port for debugging. ("Driver=usbfs" when ADB server enabled)
Here are the outputs of lsusb and usb-devices:
$ ls /dev/ttyUSB*
/dev/ttyUSB0 /dev/ttyUSB1 /dev/ttyUSB2 /dev/ttyUSB3
usb-devices:
L716-EU (ECM mode):
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 51 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=0001 Rev= 1.00
S: Manufacturer=Fibocom,Incorporated
S: Product=Fibocom Mobile Boardband
S: SerialNumber=1234567890ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=87(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
L716-EU (RNDIS mode):
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 49 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=0001 Rev= 1.00
S: Manufacturer=Fibocom,Incorporated
S: Product=Fibocom Mobile Boardband
S: SerialNumber=1234567890ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=ff Driver=rndis_host
E: Ad=87(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Victor Fragoso <victorffs@hotmail.com>
Reviewed-by: Lars Melin <larsm17@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Use atomic_try_cmpxchg() instead of atomic_cmpxchg(*ptr, old, new) == old
in hv_nmi_unknown(). On x86 the CMPXCHG instruction returns success in
the ZF flag, so this change saves a compare after CMPXCHG. The generated
asm code improves from:
3e: 65 8b 15 00 00 00 00 mov %gs:0x0(%rip),%edx
45: b8 ff ff ff ff mov $0xffffffff,%eax
4a: f0 0f b1 15 00 00 00 lock cmpxchg %edx,0x0(%rip)
51: 00
52: 83 f8 ff cmp $0xffffffff,%eax
55: 0f 95 c0 setne %al
to:
3e: 65 8b 15 00 00 00 00 mov %gs:0x0(%rip),%edx
45: b8 ff ff ff ff mov $0xffffffff,%eax
4a: f0 0f b1 15 00 00 00 lock cmpxchg %edx,0x0(%rip)
51: 00
52: 0f 95 c0 setne %al
No functional change intended.
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20231114170038.381634-1-ubizjak@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20231114170038.381634-1-ubizjak@gmail.com>
|
|
We should clean the skb resource if genlmsg_put_reply failed.
Fixes: 9d71b54b65b1 ("dpll: netlink: Add DPLL framework base functions")
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://lore.kernel.org/r/20231121013709.73323-1-gehao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-11-21
We've added 19 non-merge commits during the last 4 day(s) which contain
a total of 18 files changed, 1043 insertions(+), 416 deletions(-).
The main changes are:
1) Fix BPF verifier to validate callbacks as if they are called an unknown
number of times in order to fix not detecting some unsafe programs,
from Eduard Zingerman.
2) Fix bpf_redirect_peer() handling which missed proper stats accounting
for veth and netkit and also generally fix missing stats for the latter,
from Peilin Ye, Daniel Borkmann et al.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: check if max number of bpf_loop iterations is tracked
bpf: keep track of max number of bpf_loop callback iterations
selftests/bpf: test widening for iterating callbacks
bpf: widening for callback iterators
selftests/bpf: tests for iterating callbacks
bpf: verify callbacks as if they are called unknown number of times
bpf: extract setup_func_entry() utility function
bpf: extract __check_reg_arg() utility function
selftests/bpf: fix bpf_loop_bench for new callback verification scheme
selftests/bpf: track string payload offset as scalar in strobemeta
selftests/bpf: track tcp payload offset as scalar in xdp_synproxy
selftests/bpf: Add netkit to tc_redirect selftest
selftests/bpf: De-veth-ize the tc_redirect test case
bpf, netkit: Add indirect call wrapper for fetching peer dev
bpf: Fix dev's rx stats for bpf_redirect_peer traffic
veth: Use tstats per-CPU traffic counters
netkit: Add tstats per-CPU traffic counters
net: Move {l,t,d}stats allocation to core and convert veth & vrf
net, vrf: Move dstats structure to core
====================
Link: https://lore.kernel.org/r/20231121193113.11796-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There has been more than a few threads which went idle before
the merge window and now people came back to them and started
asking about next steps.
We currently tell people to be patient and not to repost too
often. Our "not too often", however, is still a few orders of
magnitude faster than other subsystems. Or so I feel after
hearing people talk about review rates at LPC.
Clarify in the doc that if the discussion went idle for a week
on netdev, 95% of the time there's no point waiting longer.
Link: https://lore.kernel.org/r/20231120200109.620392-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device,
the following test cycle has been implemented:
- power on
- check logs
- shutdown
- after detecting the system shutdown, disconnect power
- after approximately 60 seconds of sleep, power is restored
Running some cycles, sometimes error logs like this appear:
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19
...
These failed operation are happening during ax88179_reset execution, so
the initialization could not be correct.
In order to avoid this, we need to increase the delay after reset and
clock initial operations. By using these larger values, many cycles
have been run and no failed operations appear.
It would be better to check some status register to verify when the
operation has finished, but I do not have found any available information
(neither in the public datasheets nor in the manufacturer's driver). The
only available information for the necessary delays is the maufacturer's
driver (original values) but the proposed values are not enough for the
tested devices.
Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Reported-by: Herb Wei <weihao.bj@ieisystem.com>
Tested-by: Herb Wei <weihao.bj@ieisystem.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
