| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull xfs fix from Chandan Babu:
- Validate quota records recovered from the log before writing them to
the disk.
* tag 'xfs-6.7-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: dquot recovery does not validate the recovered dquot
xfs: clean up dqblk extraction
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix "rodata=on" not disabling "rodata=full" on arm64
- Add arm64 make dependency between vmlinuz.efi and Image, leading to
occasional build failures previously (with parallel building)
- Add newline to the output formatting of the za-fork kselftest
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: add dependency between vmlinuz.efi and Image
kselftest/arm64: Fix output formatting for za-fork
arm64: mm: Fix "rodata=on" when CONFIG_RODATA_FULL_DEFAULT_ENABLED=y
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- A small cleanup patch for the Xen privcmd driver
- A fix for the swiotlb-xen driver which was missing the advertising of
the maximum mapping length
- A fix for Xen on Arm for a longstanding bug, which happened to occur
only recently: a structure in percpu memory crossed a page boundary,
which was rejected by the hypervisor
* tag 'for-linus-6.7a-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
arm/xen: fix xen_vcpu_info allocation alignment
xen: privcmd: Replace zero-length array with flex-array member and use __counted_by
swiotlb-xen: provide the "max_mapping_size" method
|
|
Enable GENERIC_BUG_RELATIVE_POINTERS which will store 32-bit relative
offsets to the bug address and the source file name instead of 64-bit
absolute addresses. This effectively reduces the size of the
bug_table[] array by half on 64-bit kernels.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Those return codes are only defined for the parisc architecture and
are leftovers from when we wanted to be HP-UX compatible.
They are not returned by any Linux kernel syscall but do trigger
problems with the glibc strerrorname_np() and strerror() functions as
reported in glibc issue #31080.
There is no need to keep them, so simply remove them.
Signed-off-by: Helge Deller <deller@gmx.de>
Reported-by: Bruno Haible <bruno@clisp.org>
Closes: https://sourceware.org/bugzilla/show_bug.cgi?id=31080
Cc: stable@vger.kernel.org
|
|
Make sure that the __bug_table section gets 32- or 64-bit aligned,
depending if a 32- or 64-bit kernel is being built.
Mark it non-writeable and use .blockz instead of the .org assembler
directive to pad the struct.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v6.0+
|
|
Make sure the .PARISC.unwind section will be 32-bit aligned.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v6.0+
|
|
On parisc we need 16-byte alignment for variables which are used for
locking. Mark the __lock_aligned attribute acordingly so that the
.data..lock_aligned section will get that alignment in the generated
object files.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v6.0+
|
|
The jump_table stores two 32-bit words and one 32- (on 32-bit kernel)
or one 64-bit word (on 64-bit kernel).
Ensure that the last word is always 64-bit aligned on a 64-bit kernel
by aligning the whole structure on sizeof(long).
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v6.0+
|
|
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v6.0+
|
|
Add an align statement to tell the linker that all ex_table entries and as
such the whole ex_table section should be 32-bit aligned in vmlinux and modules.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v6.0+
|
|
Add an align statement to tell the linker that all ex_table entries and as
such the whole ex_table section should be 32-bit aligned in vmlinux and modules.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v6.0+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Alexander Gordeev:
- Remove unnecessary assignment of the performance event last_tag.
- Create missing /sys/firmware/ipl/* attributes when kernel is booted
in dump mode using List-directed ECKD IPL.
- Remove odd comment.
- Fix s390-specific part of scripts/checkstack.pl script that only
matches three-digit numbers starting with 3 or any higher number and
skips any stack sizes smaller than 304 bytes.
* tag 's390-6.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
scripts/checkstack.pl: match all stack sizes for s390
s390: remove odd comment
s390/ipl: add missing IPL_TYPE_ECKD_DUMP case to ipl_init()
s390/pai: cleanup event initialization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These add an ACPI IRQ override quirk for ASUS ExpertBook B1402CVA and
fix an ACPI processor idle issue leading to triple-faults in Xen HVM
guests and an ACPI backlight driver issue that causes GPUs to
misbehave while their children power is being fixed up.
Specifics:
- Avoid powering up GPUs while attempting to fix up power for their
children (Hans de Goede)
- Use raw_safe_halt() instead of safe_halt() in acpi_idle_play_dead()
so as to avoid triple-falts during CPU online in Xen HVM guests due
to the setting of the hardirqs_enabled flag in safe_halt() (David
Woodhouse)
- Add an ACPI IRQ override quirk for ASUS ExpertBook B1402CVA (Hans
de Goede)"
* tag 'acpi-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CVA
ACPI: video: Use acpi_device_fix_up_power_children()
ACPI: PM: Add acpi_device_fix_up_power_children() function
ACPI: processor_idle: use raw_safe_halt() in acpi_idle_play_dead()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a syntax error in the sleepgraph utility which causes it to exit
early on every invocation (David Woodhouse)"
* tag 'pm-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: tools: Fix sleepgraph syntax error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull AFS fixes from David Howells:
- Fix the afs_server_list struct to be cleaned up with RCU
- Fix afs to translate a no-data result from a DNS lookup into ENOENT,
not EDESTADDRREQ for consistency with OpenAFS
- Fix afs to translate a negative DNS lookup result into ENOENT rather
than EDESTADDRREQ
- Fix file locking on R/O volumes to operate in local mode as the
server doesn't handle exclusive locks on such files
- Set SB_RDONLY on superblocks for RO and Backup volumes so that the
VFS can see that they're read only
* tag 'afs-fixes-20231124' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Mark a superblock for an R/O or Backup volume as SB_RDONLY
afs: Fix file locking on R/O volumes to operate in local mode
afs: Return ENOENT if no cell DNS record can be found
afs: Make error on cell lookup failure consistent with OpenAFS
afs: Fix afs_server_list to be cleaned up with RCU
|
|
Merge ACPI backlight driver fixes and an ACPI processor driver fix for
6.7-rc3:
- Avoid powering up GPUs while attempting to fix up power for their
children (Hans de Goede).
- Use raw_safe_halt() instead of safe_halt() in acpi_idle_play_dead()
so as to avoid triple-falts during CPU online in Xen HVM guests due
to the setting of the hardirqs_enabled flag in safe_halt() (David
Woodhouse).
* acpi-video:
ACPI: video: Use acpi_device_fix_up_power_children()
ACPI: PM: Add acpi_device_fix_up_power_children() function
* acpi-processor:
ACPI: processor_idle: use raw_safe_halt() in acpi_idle_play_dead()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
- Avoid calling back into LSMs from vfs_getattr_nosec() calls.
IMA used to query inode properties accessing raw inode fields without
dedicated helpers. That was finally fixed a few releases ago by
forcing IMA to use vfs_getattr_nosec() helpers.
The goal of the vfs_getattr_nosec() helper is to query for attributes
without calling into the LSM layer which would be quite problematic
because incredibly IMA is called from __fput()...
__fput()
-> ima_file_free()
What it does is to call back into the filesystem to update the file's
IMA xattr. Querying the inode without using vfs_getattr_nosec() meant
that IMA didn't handle stacking filesystems such as overlayfs
correctly. So the switch to vfs_getattr_nosec() is quite correct. But
the switch to vfs_getattr_nosec() revealed another bug when used on
stacking filesystems:
__fput()
-> ima_file_free()
-> vfs_getattr_nosec()
-> i_op->getattr::ovl_getattr()
-> vfs_getattr()
-> i_op->getattr::$WHATEVER_UNDERLYING_FS_getattr()
-> security_inode_getattr() # calls back into LSMs
Now, if that __fput() happens from task_work_run() of an exiting task
current->fs and various other pointer could already be NULL. So
anything in the LSM layer relying on that not being NULL would be
quite surprised.
Fix that by passing the information that this is a security request
through to the stacking filesystem by adding a new internal
ATT_GETATTR_NOSEC flag. Now the callchain becomes:
__fput()
-> ima_file_free()
-> vfs_getattr_nosec()
-> i_op->getattr::ovl_getattr()
-> if (AT_GETATTR_NOSEC)
vfs_getattr_nosec()
else
vfs_getattr()
-> i_op->getattr::$WHATEVER_UNDERLYING_FS_getattr()
- Fix a bug introduced with the iov_iter rework from last cycle.
This broke /proc/kcore by copying too much and without the correct
offset.
- Add a missing NULL check when allocating the root inode in
autofs_fill_super().
- Fix stable writes for multi-device filesystems (xfs, btrfs etc) and
the block device pseudo filesystem.
Stable writes used to be a superblock flag only, making it a per
filesystem property. Add an additional AS_STABLE_WRITES mapping flag
to allow for fine-grained control.
- Ensure that offset_iterate_dir() returns 0 after reaching the end of
a directory so it adheres to getdents() convention.
* tag 'vfs-6.7-rc3.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
libfs: getdents() should return 0 after reaching EOD
xfs: respect the stable writes flag on the RT device
xfs: clean up FS_XFLAG_REALTIME handling in xfs_ioctl_setattr_xflags
block: update the stable_writes flag in bdev_add
filemap: add a per-mapping stable writes flag
autofs: add: new_inode check in autofs_fill_super()
iov_iter: fix copy_page_to_iter_nofault()
fs: Pass AT_GETATTR_NOSEC flag to getattr interface function
|
|
Pull drm fixes from Dave Airlie:
"Back to regular scheduled fixes pull request, mainly a bunch of msm,
some i915 and otherwise a few scattered, one memory crasher in the
nouveau GSP paths is helping stabilise that work.
msm:
- Fix the VREG_CTRL_1 for 4nm CPHY to match downstream
- Remove duplicate call to drm_kms_helper_poll_init() in
msm_drm_init()
- Fix the safe_lut_tbl[] for sc8280xp to match downstream
- Don't attach the drm_dp_set_subconnector_property() for eDP
- Fix to attach drm_dp_set_subconnector_property() for DP. Otherwise
there is a bootup crash on multiple targets
- Remove unnecessary NULL check left behind during cleanup
i915:
- Fix race between DP MST connectore registration and setup
- Fix GT memory leak on probe error path
panel:
- Fixes for innolux and auo,b101uan08.3 panel.
- Fix Himax83102-j02 timings.
ivpu:
- Fix ivpu MMIO reset.
ast:
- AST fix on connetor disconnection.
nouveau:
- gsp memory corruption fix
rockchip:
- color fix"
* tag 'drm-fixes-2023-11-24' of git://anongit.freedesktop.org/drm/drm:
nouveau/gsp: allocate enough space for all channel ids.
drm/panel: boe-tv101wum-nl6: Fine tune Himax83102-j02 panel HFP and HBP
drm/ast: Disconnect BMC if physical connector is connected
accel/ivpu/37xx: Fix hangs related to MMIO reset
drm/rockchip: vop: Fix color for RGB888/BGR888 format on VOP full
drm/i915: do not clean GT table on error path
drm/i915/dp_mst: Fix race between connector registration and setup
drm/panel: simple: Fix Innolux G101ICE-L01 timings
drm/panel: simple: Fix Innolux G101ICE-L01 bus flags
drm/msm: remove unnecessary NULL check
drm/panel: auo,b101uan08.3: Fine tune the panel power sequence
drm/msm/dp: attach the DP subconnector property
drm/msm/dp: don't touch DP subconnector property in eDP case
drm/msm/dpu: Add missing safe_lut_tbl in sc8280xp catalog
drm/msm: remove exra drm_kms_helper_poll_init() call
drm/msm/dsi: use the correct VREG_CTRL_1 value for 4nm cphy
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 6.7-rc3
Here are a couple of modem device entry fixes and some new modem device
ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.7-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (329 commits)
USB: serial: option: add Luat Air72*U series products
USB: serial: option: add Fibocom L7xx modules
USB: serial: option: fix FM101R-GL defines
USB: serial: option: don't claim interface 4 for ZTE MF290
Linux 6.7-rc2
prctl: Disable prctl(PR_SET_MDWE) on parisc
parisc/power: Fix power soft-off when running on qemu
parisc: Replace strlcpy() with strscpy()
NFSD: Fix checksum mismatches in the duplicate reply cache
NFSD: Fix "start of NFS reply" pointer passed to nfsd_cache_update()
NFSD: Update nfsd_cache_append() to use xdr_stream
nfsd: fix file memleak on client_opens_release
dm-crypt: start allocating with MAX_ORDER
dm-verity: don't use blocking calls from tasklets
dm-bufio: fix no-sleep mode
dm-delay: avoid duplicate logic
dm-delay: fix bugs introduced by kthread mode
dm-delay: fix a race between delay_presuspend and delay_bio
drm/amdgpu/gmc9: disable AGP aperture
drm/amdgpu/gmc10: disable AGP aperture
...
|
|
Mark a superblock that is for for an R/O or Backup volume as SB_RDONLY when
mounting it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
AFS doesn't really do locking on R/O volumes as fileservers don't maintain
state with each other and thus a lock on a R/O volume file on one
fileserver will not be be visible to someone looking at the same file on
another fileserver.
Further, the server may return an error if you try it.
Fix this by doing what other AFS clients do and handle filelocking on R/O
volume files entirely within the client and don't touch the server.
Fixes: 6c6c1d63c243 ("afs: Provide mount-time configurable byte-range file locking emulation")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Make AFS return error ENOENT if no cell SRV or AFSDB DNS record (or
cellservdb config file record) can be found rather than returning
EDESTADDRREQ.
Also add cell name lookup info to the cursor dump.
Fixes: d5c32c89b208 ("afs: Fix cell DNS lookup")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216637
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Kent reported an occasional KASAN splat in lockdep. Mark then noted:
> I suspect the dodgy access is to chain_block_buckets[-1], which hits the last 4
> bytes of the redzone and gets (incorrectly/misleadingly) attributed to
> nr_large_chain_blocks.
That would mean @size == 0, at which point size_to_bucket() returns -1
and the above happens.
alloc_chain_hlocks() has 'size - req', for the first with the
precondition 'size >= rq', which allows the 0.
This code is trying to split a block, del_chain_block() takes what we
need, and add_chain_block() puts back the remainder, except in the
above case the remainder is 0 sized and things go sideways.
Fixes: 810507fe6fd5 ("locking/lockdep: Reuse freed chain_hlocks entries")
Reported-by: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Kent Overstreet <kent.overstreet@linux.dev>
Link: https://lkml.kernel.org/r/20231121114126.GH8262@noisy.programming.kicks-ass.net
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fix from Damien Le Moal:
- Add a missing error check in the adapter initialization of the
pata_isapnp driver (Chen)
* tag 'ata-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_isapnp: Add missing error check for devm_ioport_map()
|
|
Pull block fixes from Jens Axboe:
"A bit bigger than usual at this time, but nothing really earth
shattering:
- NVMe pull request via Keith:
- TCP TLS fixes (Hannes)
- Authentifaction fixes (Mark, Hannes)
- Properly terminate target names (Christoph)
- MD pull request via Song, fixing a raid5 corruption issue
- Disentanglement of the dependency mess in nvme introduced with the
tls additions. Now it should actually build on all configs (Arnd)
- Series of bcache fixes (Coly)
- Removal of a dead helper (Damien)
- s390 dasd fix (Muhammad, Jan)
- lockdep blk-cgroup fixes (Ming)"
* tag 'block-6.7-2023-11-23' of git://git.kernel.dk/linux: (33 commits)
nvme: tcp: fix compile-time checks for TLS mode
nvme: target: fix Kconfig select statements
nvme: target: fix nvme_keyring_id() references
nvme: move nvme_stop_keep_alive() back to original position
nbd: pass nbd_sock to nbd_read_reply() instead of index
s390/dasd: protect device queue against concurrent access
s390/dasd: resolve spelling mistake
block/null_blk: Fix double blk_mq_start_request() warning
nvmet-tcp: always initialize tls_handshake_tmo_work
nvmet: nul-terminate the NQNs passed in the connect command
nvme: blank out authentication fabrics options if not configured
nvme: catch errors from nvme_configure_metadata()
nvme-tcp: only evaluate 'tls' option if TLS is selected
nvme-auth: set explanation code for failure2 msgs
nvme-auth: unlock mutex in one place only
block: Remove blk_set_runtime_active()
nbd: fix null-ptr-dereference while accessing 'nbd->config'
nbd: factor out a helper to get nbd_config without holding 'config_lock'
nbd: fold nbd config initialization into nbd_alloc_config()
bcache: avoid NULL checking to c->root in run_cache_set()
...
|
|
Pull io_uring fixes from Jens Axboe:
"A fix for ensuring that LINKAT always propagates flags correctly, and
a fix for an off-by-one in segment skipping for registered buffers.
Both heading to stable as well"
* tag 'io_uring-6.7-2023-11-23' of git://git.kernel.dk/linux:
io_uring: fix off-by one bvec index
io_uring/fs: consider link->flags when getting path for LINKAT
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- revert of commit that caused regression to many Logitech unifying
receiver users (Jiri Kosina)
- power management fix for hid-mcp2221 (Hamish Martin)
- fix for race condition between HID core and HID debug (Charles Yi)
- a couple of assorted device-ID-specific quirks
* tag 'for-linus-2023112301' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: multitouch: Add quirk for HONOR GLO-GXXX touchpad
HID: hid-asus: reset the backlight brightness level on resume
HID: hid-asus: add const to read-only outgoing usb buffer
Revert "HID: logitech-dj: Add support for a new lightspeed receiver iteration"
HID: add ALWAYS_POLL quirk for Apple kb
HID: glorious: fix Glorious Model I HID report
HID: fix HID device resource race between HID core and debugging support
HID: apple: add Jamesdonkey and A3R to non-apple keyboards list
HID: mcp2221: Allow IO to start during probe
HID: mcp2221: Set driver data before I2C adapter add
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v6.7-rc3:
- Fix race between DP MST connectore registration and setup
- Fix GT memory leak on probe error path
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87y1eol98h.fsf@intel.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v6.7-rc3:
- Panel fixes for innolux and auo,b101uan08.3 panel.
- Fix ivpu MMIO reset.
- AST fix on connetor disconnection.
- nouveau gsp fix.
- rockchip color fix.
- Fix Himax83102-j02 timings.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/12322257-2e0c-43d3-8241-876aafc10e4a@linux.intel.com
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
Fixes for v6.7-rc3:
- Fix the VREG_CTRL_1 for 4nm CPHY to match downstream
- Remove duplicate call to drm_kms_helper_poll_init() in msm_drm_init()
- Fix the safe_lut_tbl[] for sc8280xp to match downstream
- Don't attach the drm_dp_set_subconnector_property() for eDP
- Fix to attach drm_dp_set_subconnector_property() for DP. Otherwise
there is a bootup crash on multiple targets
- Remove unnecessary NULL check left behind during cleanup
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtkna3P3mvaF53n2ARJACaXQU+OFfShayTrsUVmqCOmNQ@mail.gmail.com
|
|
A common issue in Makefile is a race in parallel building.
You need to be careful to prevent multiple threads from writing to the
same file simultaneously.
Commit 3939f3345050 ("ARM: 8418/1: add boot image dependencies to not
generate invalid images") addressed such a bad scenario.
A similar symptom occurs with the following command:
$ make -j$(nproc) ARCH=arm64 Image vmlinuz.efi
[ snip ]
SORTTAB vmlinux
OBJCOPY arch/arm64/boot/Image
OBJCOPY arch/arm64/boot/Image
AS arch/arm64/boot/zboot-header.o
PAD arch/arm64/boot/vmlinux.bin
GZIP arch/arm64/boot/vmlinuz
OBJCOPY arch/arm64/boot/vmlinuz.o
LD arch/arm64/boot/vmlinuz.efi.elf
OBJCOPY arch/arm64/boot/vmlinuz.efi
The log "OBJCOPY arch/arm64/boot/Image" is displayed twice.
It indicates that two threads simultaneously enter arch/arm64/boot/
and write to arch/arm64/boot/Image.
It occasionally leads to a build failure:
$ make -j$(nproc) ARCH=arm64 Image vmlinuz.efi
[ snip ]
SORTTAB vmlinux
OBJCOPY arch/arm64/boot/Image
PAD arch/arm64/boot/vmlinux.bin
truncate: Invalid number: 'arch/arm64/boot/vmlinux.bin'
make[2]: *** [drivers/firmware/efi/libstub/Makefile.zboot:13:
arch/arm64/boot/vmlinux.bin] Error 1
make[2]: *** Deleting file 'arch/arm64/boot/vmlinux.bin'
make[1]: *** [arch/arm64/Makefile:163: vmlinuz.efi] Error 2
make[1]: *** Waiting for unfinished jobs....
make: *** [Makefile:234: __sub-make] Error 2
vmlinuz.efi depends on Image, but such a dependency is not specified
in arch/arm64/Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: SImon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20231119053234.2367621-1-masahiroy@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf.
Current release - regressions:
- Revert "net: r8169: Disable multicast filter for RTL8168H and
RTL8107E"
- kselftest: rtnetlink: fix ip route command typo
Current release - new code bugs:
- s390/ism: make sure ism driver implies smc protocol in kconfig
- two build fixes for tools/net
Previous releases - regressions:
- rxrpc: couple of ACK/PING/RTT handling fixes
Previous releases - always broken:
- bpf: verify bpf_loop() callbacks as if they are called unknown
number of times
- improve stability of auto-bonding with Hyper-V
- account BPF-neigh-redirected traffic in interface statistics
Misc:
- net: fill in some more MODULE_DESCRIPTION()s"
* tag 'net-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
tools: ynl: fix duplicate op name in devlink
tools: ynl: fix header path for nfsd
net: ipa: fix one GSI register field width
tls: fix NULL deref on tls_sw_splice_eof() with empty record
net: axienet: Fix check for partial TX checksum
vsock/test: fix SEQPACKET message bounds test
i40e: Fix adding unsupported cloud filters
ice: restore timestamp configuration after device reset
ice: unify logic for programming PFINT_TSYN_MSK
ice: remove ptp_tx ring parameter flag
amd-xgbe: propagate the correct speed and duplex status
amd-xgbe: handle the corner-case during tx completion
amd-xgbe: handle corner-case during sfp hotplug
net: veth: fix ethtool stats reporting
octeontx2-pf: Fix ntuple rule creation to direct packet to VF with higher Rx queue than its PF
net: usb: qmi_wwan: claim interface 4 for ZTE MF290
Revert "net: r8169: Disable multicast filter for RTL8168H and RTL8107E"
net/smc: avoid data corruption caused by decline
nfc: virtual_ncidev: Add variable to check if ndev is running
dpll: Fix potential msg memleak when genlmsg_put_reply failed
...
|
|
Remove duplicate code and add new helper for creating special files in
SFU (Services for UNIX) format that can be shared by SMB1+ code.
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Handle all file types in NFS reparse points as specified in MS-FSCC
2.1.2.6 Network File System (NFS) Reparse Data Buffer.
The client is now able to set all file types based on the parsed NFS
reparse point, which used to support only symlinks. This works for
SMB1+.
Before patch:
$ mount.cifs //srv/share /mnt -o ...
$ ls -l /mnt
ls: cannot access 'block': Operation not supported
ls: cannot access 'char': Operation not supported
ls: cannot access 'fifo': Operation not supported
ls: cannot access 'sock': Operation not supported
total 1
l????????? ? ? ? ? ? block
l????????? ? ? ? ? ? char
-rwxr-xr-x 1 root root 5 Nov 18 23:22 f0
l????????? ? ? ? ? ? fifo
l--------- 1 root root 0 Nov 18 23:23 link -> f0
l????????? ? ? ? ? ? sock
After patch:
$ mount.cifs //srv/share /mnt -o ...
$ ls -l /mnt
total 1
brwxr-xr-x 1 root root 123, 123 Nov 18 00:34 block
crwxr-xr-x 1 root root 1234, 1234 Nov 18 00:33 char
-rwxr-xr-x 1 root root 5 Nov 18 23:22 f0
prwxr-xr-x 1 root root 0 Nov 18 23:23 fifo
lrwxr-xr-x 1 root root 0 Nov 18 23:23 link -> f0
srwxr-xr-x 1 root root 0 Nov 19 2023 sock
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Parse reparse point into cifs_open_info_data structure and feed it
through cifs_open_info_to_fattr().
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Reparse points are not limited to symlinks, so implement
->query_reparse_point() in order to handle different file types.
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
We were deferencing iface after it has been released. Fix is to
release after all dereference instances have been encountered.
Signed-off-by: Ritvik Budhiraja <rbudhiraja@microsoft.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202311110815.UJaeU3Tt-lkp@intel.com/
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Update the USB serial option driver support for Luat Air72*U series
products.
ID 1782:4e00 Spreadtrum Communications Inc. UNISOC-8910
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 13 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1782 ProdID=4e00 Rev=00.00
S: Manufacturer=UNISOC
S: Product=UNISOC-8910
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=400mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=4096ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
If#= 2: AT
If#= 3: PPP + AT
If#= 4: Debug
Co-developed-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Asuna Yang <SpriteOvO@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
We don't support CRUD-inspired message types in YNL too well.
One aspect that currently trips us up is the fact that single
message ID can be used in multiple commands (as the response).
This leads to duplicate entries in the id-to-string tables:
devlink-user.c:19:34: warning: initialized field overwritten [-Woverride-init]
19 | [DEVLINK_CMD_PORT_NEW] = "port-new",
| ^~~~~~~~~~
devlink-user.c:19:34: note: (near initialization for ‘devlink_op_strmap[7]’)
Fixes tag points at where the code was generated, the "real" problem
is that the code generator does not support CRUD.
Fixes: f2f9dd164db0 ("netlink: specs: devlink: add the remaining command to generate complete split_ops")
Link: https://lore.kernel.org/r/20231123030558.1611831-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The makefile dependency is trying to include the wrong header:
<command-line>: fatal error: ../../../../include/uapi//linux/nfsd.h: No such file or directory
The guard also looks wrong.
Fixes: f14122b2c2ac ("tools: ynl: Add source files for nfsd netlink protocol")
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://lore.kernel.org/r/20231123030624.1611925-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The width of the R_LENGTH field of the EV_CH_E_CNTXT_1 GSI register
is 24 bits (not 20 bits) starting with IPA v5.0. Fix this.
Fixes: faf0678ec8a0 ("net: ipa: add IPA v5.0 GSI register definitions")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20231122231708.896632-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzkaller discovered that if tls_sw_splice_eof() is executed as part of
sendfile() when the plaintext/ciphertext sk_msg are empty, the send path
gets confused because the empty ciphertext buffer does not have enough
space for the encryption overhead. This causes tls_push_record() to go on
the `split = true` path (which is only supposed to be used when interacting
with an attached BPF program), and then get further confused and hit the
tls_merge_open_record() path, which then assumes that there must be at
least one populated buffer element, leading to a NULL deref.
It is possible to have empty plaintext/ciphertext buffers if we previously
bailed from tls_sw_sendmsg_locked() via the tls_trim_both_msgs() path.
tls_sw_push_pending_record() already handles this case correctly; let's do
the same check in tls_sw_splice_eof().
Fixes: df720d288dbb ("tls/sw: Use splice_eof() to flush")
Cc: stable@vger.kernel.org
Reported-by: syzbot+40d43509a099ea756317@syzkaller.appspotmail.com
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20231122214447.675768-1-jannh@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Due to a typo, the code checked the RX checksum feature in the TX path.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/20231122004219.3504219-1-samuel.holland@sifive.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tune message length calculation to make this test work on machines
where 'getpagesize()' returns >32KB. Now maximum message length is not
hardcoded (on machines above it was smaller than 'getpagesize()' return
value, thus we get negative value and test fails), but calculated at
runtime and always bigger than 'getpagesize()' result. Reproduced on
aarch64 with 64KB page size.
Fixes: 5c338112e48a ("test/vsock: rework message bounds test")
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reported-by: Bogdan Marcynkov <bmarcynk@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20231121211642.163474-1-avkrasnov@salutedevices.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a VF tries to add unsupported cloud filter through virtchnl
then i40e_add_del_cloud_filter(_big_buf) returns -ENOTSUPP but
this error code is stored in 'ret' instead of 'aq_ret' that
is used as error code sent back to VF. In this scenario where
one of the mentioned functions fails the value of 'aq_ret'
is zero so the VF will incorrectly receive a 'success'.
Use 'aq_ret' to store return value and remove 'ret' local
variable. Additionally fix the issue when filter allocation
fails, in this case no notification is sent back to the VF.
Fixes: e284fc280473 ("i40e: Add and delete cloud filter")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231121211338.3348677-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tony Nguyen says:
====================
ice: restore timestamp config after reset
Jake Keller says:
We recently discovered during internal validation that the ice driver has
not been properly restoring Tx timestamp configuration after a device reset,
which resulted in application failures after a device reset.
After some digging, it turned out this problem is two-fold. Since the
introduction of the PTP support the driver has been clobbering the storage
of the current timestamp configuration during reset. Thus after a reset, the
driver will no longer perform Tx or Rx timestamps, and will report
timestamp configuration as disabled if SIOCGHWTSTAMP ioctl is issued.
In addition, the recently merged auxiliary bus support code missed that
PFINT_TSYN_MSK must be reprogrammed on the clock owner for E822 devices.
Failure to restore this register configuration results in the driver no
longer responding to interrupts from other ports. Depending on the traffic
pattern, this can either result in increased latency responding to
timestamps on the non-owner ports, or it can result in the driver never
reporting any timestamps. The configuration of PFINT_TSYN_MSK was only done
during initialization. Due to this, the Tx timestamp issue persists even if
userspace reconfigures timestamping.
This series fixes both issues, as well as removes a redundant Tx ring field
since we can rely on the skb flag as the primary detector for a Tx timestamp
request.
Note that I don't think this series will directly apply to older stable
releases (even v6.6) as we recently refactored a lot of the PTP code to
support auxiliary bus. Patch 2/3 only matters for the post-auxiliary bus
implementation. The principle of patch 1/3 and 3/3 could apply as far back
as the initial PTP support, but I don't think it will apply cleanly as-is.
====================
Link: https://lore.kernel.org/r/20231121211259.3348630-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The driver calls ice_ptp_cfg_timestamp() during ice_ptp_prepare_for_reset()
to disable timestamping while the device is resetting. This operation
destroys the user requested configuration. While the driver does call
ice_ptp_cfg_timestamp in ice_rebuild() to restore some hardware settings
after a reset, it unconditionally passes true or false, resulting in
failure to restore previous user space configuration.
This results in a device reset forcibly disabling timestamp configuration
regardless of current user settings.
This was not detected previously due to a quirk of the LinuxPTP ptp4l
application. If ptp4l detects a missing timestamp, it enters a fault state
and performs recovery logic which includes executing SIOCSHWTSTAMP again,
restoring the now accidentally cleared configuration.
Not every application does this, and for these applications, timestamps
will mysteriously stop after a PF reset, without being restored until an
application restart.
Fix this by replacing ice_ptp_cfg_timestamp() with two new functions:
1) ice_ptp_disable_timestamp_mode() which unconditionally disables the
timestamping logic in ice_ptp_prepare_for_reset() and ice_ptp_release()
2) ice_ptp_restore_timestamp_mode() which calls
ice_ptp_restore_tx_interrupt() to restore Tx timestamping configuration,
calls ice_set_rx_tstamp() to restore Rx timestamping configuration, and
issues an immediate TSYN_TX interrupt to ensure that timestamps which
may have occurred during the device reset get processed.
Modify the ice_ptp_set_timestamp_mode to directly save the user
configuration and then call ice_ptp_restore_timestamp_mode. This way, reset
no longer destroys the saved user configuration.
This obsoletes the ice_set_tx_tstamp() function which can now be safely
removed.
With this change, all devices should now restore Tx and Rx timestamping
functionality correctly after a PF reset without application intervention.
Fixes: 77a781155a65 ("ice: enable receive hardware timestamping")
Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit d938a8cca88a ("ice: Auxbus devices & driver for E822 TS") modified
how Tx timestamps are handled for E822 devices. On these devices, only the
clock owner handles reading the Tx timestamp data from firmware. To do
this, the PFINT_TSYN_MSK register is modified from the default value to one
which enables reacting to a Tx timestamp on all PHY ports.
The driver currently programs PFINT_TSYN_MSK in different places depending
on whether the port is the clock owner or not. For the clock owner, the
PFINT_TSYN_MSK value is programmed during ice_ptp_init_owner just before
calling ice_ptp_tx_ena_intr to program the PHY ports.
For the non-clock owner ports, the PFINT_TSYN_MSK is programmed during
ice_ptp_init_port.
If a large enough device reset occurs, the PFINT_TSYN_MSK register will be
reset to the default value in which only the PHY associated directly with
the PF will cause the Tx timestamp interrupt to trigger.
The driver lacks logic to reprogram the PFINT_TSYN_MSK register after a
device reset. For the E822 device, this results in the PF no longer
responding to interrupts for other ports. This results in failure to
deliver Tx timestamps to user space applications.
Rename ice_ptp_configure_tx_tstamp to ice_ptp_cfg_tx_interrupt, and unify
the logic for programming PFINT_TSYN_MSK and PFINT_OICR_ENA into one place.
This function will program both registers according to the combination of
user configuration and device requirements.
This ensures that PFINT_TSYN_MSK is always restored when we configure the
Tx timestamp interrupt.
Fixes: d938a8cca88a ("ice: Auxbus devices & driver for E822 TS")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Before performing a Tx timestamp in ice_stamp(), the driver checks a ptp_tx
ring variable to see if timestamping is enabled on that ring. This value is
set for all rings whenever userspace configures Tx timestamping.
Ostensibly this was done to avoid wasting cycles checking other fields when
timestamping has not been enabled. However, for Tx timestamps we already
get an individual per-SKB flag indicating whether userspace wants to
request a timestamp on that packet. We do not gain much by also having
a separate flag to check for whether timestamping was enabled.
In fact, the driver currently fails to restore the field after a PF reset.
Because of this, if a PF reset occurs, timestamps will be disabled.
Since this flag doesn't add value in the hotpath, remove it and always
provide a timestamp if the SKB flag has been set.
A following change will fix the reset path to properly restore user
timestamping configuration completely.
This went unnoticed for some time because one of the most common
applications using Tx timestamps, ptp4l, will reconfigure the socket as
part of its fault recovery logic.
Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
