Age | Commit message (Collapse) | Author | Files | Lines |
|
Pull MMC updates from Ulf Hansson:
- dt-bindings: Increase maximum supported frequency to 384MHz
- dw_mmc-rockchip: Add support for the rk3128 variant
- meson-gx: Add support for SDIO interrupts
- mtk-sd: Add support for MT6795 Helio X10 variant
- sdhci: Improve the code by centralizing the CMD/DATA reset handling
- sdhci-msm:
- Add support for the sdm670 variant
- Add support for the sm6115 variant
- sdhci-omap: Make Vignesh replace Kishon as the maintainer
- sdhci-pci-o2micro: Disable fragile support for DDR50 in favor of
SDR50
- sdhci-sprd: Fix clock divider limitation
* tag 'mmc-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (31 commits)
mmc: sdhci: Centralize CMD and DATA reset handling
mmc: sdhci: Get rid of SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS
mmc: sdhci: Remove misleading comment about resets
mmc: sdhci: Separate out sdhci_reset_for_all()
MAINTAINERS: Add Vignesh as maintainer of TI SDHCI OMAP DRIVER
mmc: sdhci-msm: add compatible string check for sdm670
dt-bindings: mmc: sdhci-msm: add sdm670 compatible
mmc: wmt-sdmmc: Fix an error handling path in wmt_mci_probe()
mmc: rtsx_usb_sdmmc: Remove the unneeded result variable
mmc: sdhci-of-aspeed: Add dependency on ARCH_ASPEED
mmc: mtk-sd: Add support for MT6795 Helio X10
mmc: mtk-sd: Reorder of_device_id and platform data by name
mmc: sdhci-sprd: Fix the limitation of div
dt-bindings: mmc: sdhci-msm: Add pinctrl-1 property
dt-bindings: mmc: rockchip: add rockchip,rk3128-dw-mshc
dt-bindings: mmc: renesas,sdhi: Add iommus property
mmc: sdhci_am654: Remove the unneeded result variable
mmc: meson-gx: add SDIO interrupt support
mmc: meson-gx: adjust and re-use constant IRQ_EN_MASK
mmc: jz4740_mmc: Fix error check for dma_map_sg
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"With the exception of some refactoring to fix long standing issues
where we weren't handling cache syncs properly for messages which had
PIO and DMA transfers going to the same page correctly there has been
no work on the core this time around, and it's also been quite a quiet
release for the drivers too:
- Fix cache syncs for cases where we have DMA and PIO transfers in
the same message going to the same page
- Update the fsl_spi driver to use transfer_one() rather than a
custom transfer function
- Support for configuring transfer speeds with the AMD SPI controller
- Support for a second chip select and 64K erase on Intel SPI
- Support for Microchip coreQSPI, Nuvoton NPCM845, NXP i.MX93, and
Rockchip RK3128 and RK3588"
* tag 'spi-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (73 commits)
spi: Ensure that sg_table won't be used after being freed
spi: spi-gxp: Use devm_platform_ioremap_resource()
spi: s3c64xx: Fix large transfers with DMA
spi: Split transfers larger than max size
spi: Fix cache corruption due to DMA/PIO overlap
spi: Save current RX and TX DMA devices
spi: mt65xx: Add dma max segment size declaration
spi: migrate mt7621 text bindings to YAML
spi: renesas,sh-msiof: Add r8a779g0 support
spi: spi-fsl-qspi: Use devm_platform_ioremap_resource_byname()
spi: spi-fsl-lpspi: Use devm_platform_get_and_ioremap_resource()
spi: spi-fsl-dspi: Use devm_platform_get_and_ioremap_resource()
spi/omap100k:Fix PM disable depth imbalance in omap1_spi100k_probe
spi: dw: Fix PM disable depth imbalance in dw_spi_bt1_probe
spi: cadence-quadspi: Fix PM disable depth imbalance in cqspi_probe
spi: s3c24xx: Switch to use devm_spi_alloc_master()
spi: xilinx: Switch to use devm_spi_alloc_master()
spi: img-spfi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
spi: aspeed: Remove redundant dev_err call
spi: spi-mpc52xx: switch to using gpiod API
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The core work this time around has mostly been around the code to
manage regulator modes, simplifying the interface for configuring
modes to not take account of the voltage and as a side effect
resolving a bootstrapping issue on systems where we can't read the
voltage from the regulator.
Otherwise it's been quite a quiet release with some new drivers and a
devm helper:
- Make the load handling in the Qualcomm RPMH regulators much more
idiomatic and general cleanups to the handling of load
configuration
- devm helper for a combined get and enable operation
- Support for MediaTek MT6331, Qualcomm PM660, 660L and PM6125, Texas
Instruments TPS65219"
* tag 'regulator-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (45 commits)
dt-bindings: gpio-regulator: add vin-supply property support
regulator: gpio: Add input_supply support in gpio_regulator_config
regulator: tps65219: Fix is_enabled checking in tps65219_set_bypass
regulator: qcom,rpmh: add pm660 and pm660l pmics
regulator: qcom-rpmh: add pm660 and pm660l pmics
regulator: of: Fix kernel-doc
regulator: of: Fix kernel-doc
regulator: Add driver for MT6332 PMIC regulators
regulator: Add bindings for MT6332 regulator
regulator: Add driver for MT6331 PMIC regulators
regulator: Add bindings for MT6331 regulator
regulator: tps65219: Fix .bypass_val_on setting
regulator: qcom_rpm: Fix circular deferral regression
regulator: core: Prevent integer underflow
regulator: dt-bindings: qcom,rpmh: Indicate regulator-allow-set-load dependencies
regulator: bd9576: switch to using devm_fwnode_gpiod_get()
regulator: bd71815: switch to using devm_fwnode_gpiod_get()
regulator: core: Fix regulator supply registration with sysfs
regulator: tps65219: change tps65219_regulator_irq_types to static
regulator: core: Don't err if allow-set-load but no allowed-modes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Driver for MAX31760 fan speed controller
- Driver for TEXAS TPS546D24 Buck Converter
- Driver for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller
Removed drivers:
- Drop obsolete asus_wmi_ec_sensors driver
Cleanups, affecting various drivers:
- Use DEFINE_SIMPLE_DEV_PM_OPS where appropriate
- Remove forward declarations
- Move from strlcpy with unused retval to strscpy
- Make use of devm_clk_get_enabled()
- Drop devm_of_pwm_get()
Other notable cleanup and improvements:
- Support for additional USB devide ID and support for reporting of
rail mode via debugfs added to corsair-psu driver
- Support for aditional USB ID in nzxt-smart2 driver
- Support for Aquacomputer High Flow Next in aquacomputer_d5next
driver
- Major cleanup of pwm-fan driver
- Major cleanup of mr75203 driver, and added support for new device
revision
And various other minor fixes and cleanups"
* tag 'hwmon-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (86 commits)
hwmon: (corsair-psu) add USB id of new revision of the HX1000i psu
hwmon: (pmbus/mp2888) Fix sensors readouts for MPS Multi-phase mp2888 controller
dt-bindings: hwmon: sensirion,shtc1: Clean up spelling mistakes and grammar
hwmon: (nct6683) remove unused variable in nct6683_create_attr_group
hwmon: w83627hf: Reorder symbols to get rid of a few forward declarations
hwmon: (ina3221) Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr()
hwmon: (w83627ehf) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (tmp108) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (tmp103) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (tmp102) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (pwm-fan) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (nct6775) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (max6639) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (max31730) witch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (max31722) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (ltc2947) Switch to EXPORT_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (lm90) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (it87) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (gpio-fan) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (adt7x10) Switch to EXPORT_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- 'remove' callback converted to return void. Big change with trivial
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
- new driver for Microchip PCI1xxxx switch
- heavy refactoring of the Mellanox BlueField driver
- we prefer async probe in the i801 driver now
- the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
* tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
i2c: pci1xxxx: prevent signed integer overflow
i2c: acpi: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
i2c: i801: Prefer async probe
i2c: designware-pci: Use standard pattern for memory allocation
i2c: designware-pci: Group AMD NAVI quirk parts together
i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch
docs: i2c: slave-interface: return errno when handle I2C_SLAVE_WRITE_REQUESTED
i2c: mlxbf: remove device tree support
i2c: mlxbf: support BlueField-3 SoC
i2c: cadence: Add standard bus recovery support
i2c: mlxbf: add multi slave functionality
i2c: mlxbf: support lock mechanism
macintosh/ams: Adapt declaration of ams_i2c_remove() to earlier change
i2c: riic: Use devm_platform_ioremap_resource()
i2c: mlxbf: remove IRQF_ONESHOT
dt-bindings: i2c: rockchip: add rockchip,rk3128-i2c
dt-bindings: i2c: renesas,rcar-i2c: Add r8a779g0 support
i2c: tegra: Add GPCDMA support
i2c: scmi: Convert to be a platform driver
i2c: rk3x: Add rv1126 support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO. This
significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF:
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions. Expose
crash_kexec() to allow BPF to trigger a kernel dump. Use
CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs. Only
structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols:
- WiFi: more Extremely High Throughput (EHT) and Multi-Link Operation
(MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state and RST
packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API:
- Allow selecting the conduit interface used by each port in DSA
switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting per
traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one of
the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much as
possible. It's one of those magic knobs which seemed like a good
idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers:
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers:
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay window
offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support"
* tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1864 commits)
eth: pse: add missing static inlines
once: rename _SLOW to _SLEEPABLE
net: pse-pd: add regulator based PSE driver
dt-bindings: net: pse-dt: add bindings for regulator based PoDL PSE controller
ethtool: add interface to interact with Ethernet Power Equipment
net: mdiobus: search for PSE nodes by parsing PHY nodes.
net: mdiobus: fwnode_mdiobus_register_phy() rework error handling
net: add framework to support Ethernet PSE and PDs devices
dt-bindings: net: phy: add PoDL PSE property
net: marvell: prestera: Propagate nh state from hw to kernel
net: marvell: prestera: Add neighbour cache accounting
net: marvell: prestera: add stub handler neighbour events
net: marvell: prestera: Add heplers to interact with fib_notifier_info
net: marvell: prestera: Add length macros for prestera_ip_addr
net: marvell: prestera: add delayed wq and flush wq on deinit
net: marvell: prestera: Add strict cleanup of fib arbiter
net: marvell: prestera: Add cleanup of allocated fib_nodes
net: marvell: prestera: Add router nexthops ABI
eth: octeon: fix build after netif_napi_add() changes
net/mlx5: E-Switch, Return EBUSY if can't get mode lock
...
|
|
Add bindings for the regulator based Ethernet PoDL PSE controller and
generic bindings for all PSE controllers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add property to reference node representing a PoDL Power Sourcing Equipment.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The yaml text contains some minor spelling mistakes and grammar issues,
clean these up.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220928213139.63819-1-colin.i.king@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Document wakeup-source property. This fixes dtbs_check warnings
when building current Linux DTs:
"
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dtb: i2c@40015000: Unevaluated properties are not allowed ('wakeup-source' was unexpected)
"
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Document interrupt-names property with "event" and "error" interrupt names.
This fixes dtbs_check warnings when building current Linux DTs:
"
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dtb: i2c@40015000: Unevaluated properties are not allowed ('interrupt-names' was unexpected)
"
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The reset line is supposed to be "active low" (it even says so in the
description), but examples incorrectly show it as "active high"
(likely because original examples use 0 which is technically "active
high" but in practice often "don't care" if the driver is using legacy
gpio API, as this one does).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/YzX+nzJolxAKmt+z@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.1
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
- refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
- support CYW43439 SDIO chipset
- support BCM4378 on Apple platforms
- support CYW89459 PCIe chipset
rtw89
- more work to get rtw8852c supported
- P2P support
- support for enabling and disabling MSDU aggregation via nl80211
mt76
- tx status reporting improvements
ath11k
- cold boot calibration support on WCN6750
- Target Wake Time (TWT) debugfs support for STA interface
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- implement SRAM dump debugfs interface
- enable threaded NAPI on all hardware
- WoW support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
wcn36xx
- add SNR from a received frame as a source of system entropy
* tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (231 commits)
wifi: rtl8xxxu: Improve rtl8xxxu_queue_select
wifi: rtl8xxxu: Fix AIFS written to REG_EDCA_*_PARAM
wifi: rtl8xxxu: gen2: Enable 40 MHz channel width
wifi: rtw89: 8852b: configure DLE mem
wifi: rtw89: check DLE FIFO size with reserved size
wifi: rtw89: mac: correct register of report IMR
wifi: rtw89: pci: set power cut closed for 8852be
wifi: rtw89: pci: add to do PCI auto calibration
wifi: rtw89: 8852b: implement chip_ops::{enable,disable}_bb_rf
wifi: rtw89: add DMA busy checking bits to chip info
wifi: rtw89: mac: define DMA channel mask to avoid unsupported channels
wifi: rtw89: pci: mask out unsupported TX channels
iwlegacy: Replace zero-length arrays with DECLARE_FLEX_ARRAY() helper
ipw2x00: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
wifi: iwlwifi: Track scan_cmd allocation size explicitly
brcmfmac: Remove the call to "dtim_assoc" IOVAR
brcmfmac: increase dcmd maximum buffer size
brcmfmac: Support 89459 pcie
brcmfmac: increase default max WOWL patterns to 16
cw1200: fix incorrect check to determine if no element is found in list
...
====================
Link: https://lore.kernel.org/r/20220930150413.A7984C433D6@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add description for new property snps,clk-csr in binding file
Signed-off-by: Jianguo Zhang <jianguo.zhang@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add binding document for the ethernet on mt8188
Signed-off-by: Jianguo Zhang <jianguo.zhang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Additional TX/RX queue pairs require dedicated interrupts. Extend
binding with additional interrupts.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Within SoCs like ZynqMP, FPGA logic can be connected to different kinds
of AXI master ports. Also cache coherent AXI master ports are available.
The property "dma-coherent" is used to signal that DMA is cache
coherent.
Add "dma-coherent" property to allow the configuration of cache coherent
DMA.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The stmmac-axi-config subnode is present in multiple dwmac instance DTs,
document its content per snps,axi-config property description which is
a phandle to this subnode.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220927012449.698915-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is same scheme as fixed-regulator.
Without that property used, the parent regulator can be shut down (if not an always on).
Thus leading to inappropriate behavior:
On am62-SP-SK this fix is required to avoid tps65219 ldo1 (SDMMC rail) to be shut down after boot completion.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Link: https://lore.kernel.org/r/20220929132526.29427-3-jneanne@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
BlueField customers have to use the BlueField firmware with
UEFI ACPI tables so there is no need to have device tree
support in the i2c-mlxbf.c driver. Remove the device tree
binding documentation as well.
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
|
|
The Snapdragon 670 supports eMMC with an SDHCI controller. Add the
appropriate compatible to the documentation.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220923014322.33620-2-mailingradian@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SoC MT7621 SPI bindings used text format, so migrate them to YAML.
There are some additions to the binding that were not in the original
file. This binding is used in MT7621 and MT7628a Ralink SoCs. To
properly match both dts nodes in tree we need to add to the schema
'clocks', 'clock-names' and 'reset-names'. Both 'clock-names' and
'reset-names' use 'spi' as string so maintain that as const in
the schema.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20220927031929.807070-1-sergio.paracuellos@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document support for the Clock-Synchronized Serial Interface with FIFO
(MSIOF) in the Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/a840ca8487cfd612fae2b20c98e93ae7c7f50ef4.1664204638.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ath.git patches for v6.1. Major changes:
ath11k
* cold boot calibration support on WCN6750
* Target Wake Time (TWT) debugfs support for STA interface
* support to connect to a non-transmit MBSSID AP profile
* enable remain-on-channel support on WCN6750
* implement SRAM dump debugfs interface
* enable threaded NAPI on all hardware
* WoW support for WCN6750
* support to provide transmit power from firmware via nl80211
* support to get power save duration for each client
* spectral scan support for 160 MHz
wcn36xx
* add SNR from a received frame as a source of system entropy
|
|
Add compatible string for RV1126 gmac, and constrain it to
be compatible with Synopsys dwmac 4.20a.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Signed-off-by: Anand Moon <anand@edgeble.ai>
Link: https://lore.kernel.org/r/20220920140944.2535-1-anand@edgeble.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix an uninitialized variable usage in the operating performance
points code and add missing DT bindings for it.
Specifics:
- Fix uninitialized variable usage in dev_pm_opp_config_clks_simple()
(Christophe JAILLET)
- Add missing OPP DT properties (Rob Herring)"
* tag 'pm-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
dt-bindings: opp: Add missing (unevaluated|additional)Properties on child nodes
OPP: Fix an un-initialized variable usage
|
|
The SDM670 uses RPMh for managing the PM660 and PM660L. Document RPMh
support for the PMIC.
Link: https://android.googlesource.com/kernel/msm/+/58064f13c0a436a82c35f2e3b5a122d874ae5846%5E%21/#F0
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220920223331.150635-2-mailingradian@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The syscon string was introduced because the mt7621 clock driver needs to
read some registers creating a regmap from the syscon. The bindings were
added before the clock driver was properly mainlined and at first the clock
driver was using ralink architecture dependent operations rt_memc_* defined
in 'arch/mips/include/asm/mach-ralink/ralink_regs.h'.
This string is already there on the memory controller node on mt7621.dtsi.
Add syscon as a constant string on the compatible property, now that memc
became a syscon. Update the example accordingly.
Fixes: 5278e4a181ff ("dt-bindings: memory: add binding for Mediatek's MT7621 SDRAM memory controller")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Expand the description of the gpio-controller property to include the
controllable pins of the MT7530 switch.
The gpio-controller property is only used for the MT7530 switch. Therefore,
invalidate it for the MT7531 switch.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case of muxing phy0 of the MT7530 switch, the switch and the phy
will have the same address on the mdio bus, 0. This causes the ethernet
driver to fail since devices on the mdio bus cannot share an address.
Any address can be used for the switch, therefore, change the switch
address to 0x1f.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove these old mediatek bindings which are not used.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/ethernet/freescale/fec.h
7b15515fc1ca ("Revert "fec: Restart PPS after link state change"")
40c79ce13b03 ("net: fec: add stop mode support for imx8 platform")
https://lore.kernel.org/all/20220921105337.62b41047@canb.auug.org.au/
drivers/pinctrl/pinctrl-ocelot.c
c297561bc98a ("pinctrl: ocelot: Fix interrupt controller")
181f604b33cd ("pinctrl: ocelot: add ability to be used in a non-mmio configuration")
https://lore.kernel.org/all/20220921110032.7cd28114@canb.auug.org.au/
tools/testing/selftests/drivers/net/bonding/Makefile
bbb774d921e2 ("net: Add tests for bonding and team address list management")
152e8ec77640 ("selftests/bonding: add a test for bonding lladdr target")
https://lore.kernel.org/all/20220921110437.5b7dbd82@canb.auug.org.au/
drivers/net/can/usb/gs_usb.c
5440428b3da6 ("can: gs_usb: gs_can_open(): fix race dev->can.state condition")
45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
https://lore.kernel.org/all/84f45a7d-92b6-4dc5-d7a1-072152fab6ff@tessares.net/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Another set of fixes for fixes for the soc tree:
- A fix for the interrupt number on at91/lan966 ethernet PHYs
- A second round of fixes for NXP i.MX series, including a couple of
build issues, and board specific DT corrections on TQMa8MPQL,
imx8mp-venice-gw74xx and imx8mm-verdin for reliability and
partially broken functionality
- Several fixes for Rockchip SoCs, addressing a USB issue on
BPI-R2-Pro, wakeup on Gru-Bob and reliability of high-speed SD
cards, among other minor issues
- A fix for a long-running naming mistake that prevented the moxart
mmc driver from working at all
- Multiple Arm SCMI firmware fixes for hardening some corner cases"
* tag 'soc-fixes-6.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
arm64: dts: imx8mp-venice-gw74xx: fix port/phy validation
ARM: dts: lan966x: Fix the interrupt number for internal PHYs
arm64: dts: imx8mp-venice-gw74xx: fix ksz9477 cpu port
arm64: dts: imx8mp-venice-gw74xx: fix CAN STBY polarity
dt-bindings: memory-controllers: fsl,imx8m-ddrc: drop Leonard Crestez
arm64: dts: tqma8mqml: Include phy-imx8-pcie.h header
arm64: defconfig: enable ARCH_NXP
arm64: dts: imx8mp-tqma8mpql-mba8mpxl: add missing pinctrl for RTC alarm
ARM: dts: fix Moxa SDIO 'compatible', remove 'sdhci' misnomer
arm64: dts: imx8mm-verdin: extend pmic voltages
arm64: dts: rockchip: Remove 'enable-active-low' from rk3566-quartz64-a
arm64: dts: rockchip: Remove 'enable-active-low' from rk3399-puma
arm64: dts: rockchip: fix property for usb2 phy supply on rk3568-evb1-v10
arm64: dts: rockchip: fix property for usb2 phy supply on rock-3a
arm64: dts: imx8ulp: add #reset-cells for pcc
arm64: dts: tqma8mpxl-ba8mpxl: Fix button GPIOs
arm64: dts: imx8mn: remove GPU power domain reset
arm64: dts: rockchip: Set RK3399-Gru PCLK_EDP to 24 MHz
arm64: dts: imx8mm: Reverse CPLD_Dn GPIO label mapping on MX8Menlo
arm64: dts: rockchip: fix upper usb port on BPI-R2-Pro
...
|
|
Document the binding for the Wireless Ethernet Dispatch core on the
MT7986 ethernet driver
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull OPP fixes for 6.0 from Viresh Kumar:
"- Fix un-initialized variable usage (Christophe JAILLET).
- Add missing DT properties (Rob Herring)."
* tag 'opp-fixes-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
dt-bindings: opp: Add missing (unevaluated|additional)Properties on child nodes
OPP: Fix an un-initialized variable usage
|
|
Replace the free-form description of device tree bindings for VSC9959
and VSC9953 with a YAML formatted dt-schema description. This contains
more or less the same information, but reworded to be a bit more
succint.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220913125806.524314-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adding bindings for Analog Devices MAX31760 Fan-Speed Controller
Signed-off-by: Ibrahim Tilki <Ibrahim.Tilki@analog.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220910171945.48088-4-Ibrahim.Tilki@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add bindings for the ADIN1110/2111 MAC-PHY/SWITCH.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This is not used by the DSA dt-binding, so remove it from all examples.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The common dsa-port.yaml does this (and more) since commit 2ec2fb8331af
("dt-bindings: net: dsa: make phylink bindings required for CPU/DSA
ports").
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The fact that some DSA device trees use 'label = "cpu"' for the CPU port
is nothing but blind cargo cult copying. The 'label' property was never
part of the DSA DT bindings for anything except the user ports, where it
provided a hint as to what name the created netdevs should use.
DSA does use the "cpu" port label to identify a CPU port in dsa_port_parse(),
but this is only for non-OF code paths (platform data).
The proper way to identify a CPU port is to look at whether the
'ethernet' phandle is present.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Document support for the Renesas Ethernet AVB (EtherAVB-IF) block in the
Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Despite the name, R-Car V3U is the first member of the R-Car Gen4
family. Hence move its compatible value to the R-Car Gen4 section.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add fsl,s32v234-fec to compatible property to support s32v234 platform.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Lee Jones says:
====================
Immutable branch between MFD, Net and Pinctrl due for the v6.0 merge window
* tag 'ib-mfd-net-pinctrl-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: ocelot: Add support for the vsc7512 chip via spi
dt-bindings: mfd: ocelot: Add bindings for VSC7512
resource: add define macro for register address resources
pinctrl: microchip-sgpio: add ability to be used in a non-mmio configuration
pinctrl: microchip-sgpio: allow sgpio driver to be used as a module
pinctrl: ocelot: add ability to be used in a non-mmio configuration
net: mdio: mscc-miim: add ability to be used in a non-mmio configuration
mfd: ocelot: Add helper to get regmap from a resource
====================
Link: https://lore.kernel.org/r/YxrjyHcceLOFlT/c@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
equation
Add optional temperature coefficient properties:
*) moortec,ts-coeff-g
*) moortec,ts-coeff-h
*) moortec,ts-coeff-cal5
*) moortec,ts-coeff-j
If defined they shall be used instead of defaults.
The coefficients were added to device tree on top of the series property
(which can be used to select between series 5 and series 6), because
coefficients can vary between product and product, and code defaults might
not be accurate enough.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220908152449.35457-19-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add optional "moortec,ts-series" property to define the temperature
equation and coefficients that shall be used to convert the digital
output to value in milli-Celsius.
Supported series: 5 (default) and 6.
Series 5:
T = G + H * (n / cal5 - 0.5) + J * F
Where: G = 60, H = 200, cal5 = 4094, J = -0.1, F = frequency clock in MHz
Series 6:
T = G + H * (n / cal5 - 0.5)
Where: G = 57.4, H = 249.4, cal5 = 4096
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220908152449.35457-17-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for mr76006 pre-scaler which provides divide-by-2 scaling of
the input voltage, so that it can be presented to the VM for measurement
within its range (the VM input range is limited to -0.1V to 1V).
The new "moortec,vm-pre-scaler-x2" property lists the channels that use
the mr76006 pre-scaler.
The driver will use this list to multiply the voltage result by 2, to
present to the user with the actual voltage input source.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220908152449.35457-14-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|