| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use acpi_evaluate_dsm_typed() instead of open-coding _DSM
evaluation to learn device characteristics (Andy Shevchenko)
- Tidy multi-function header checks using new PCI_HEADER_TYPE_MASK
definition (Ilpo Järvinen)
- Simplify config access error checking in various drivers (Ilpo
Järvinen)
- Use pcie_capability_clear_word() (not
pcie_capability_clear_and_set_word()) when only clearing (Ilpo
Järvinen)
- Add pci_get_base_class() to simplify finding devices using base
class only (ignoring subclass and programming interface) (Sui
Jingfeng)
- Add pci_is_vga(), which includes ancient PCI_CLASS_NOT_DEFINED_VGA
devices from before the Class Code was added to PCI (Sui Jingfeng)
- Use pci_is_vga() for vgaarb, sysfs "boot_vga", virtio, qxl to
include ancient VGA devices (Sui Jingfeng)
Resource management:
- Make pci_assign_unassigned_resources() non-init because sparc uses
it after init (Randy Dunlap)
Driver binding:
- Retain .remove() and .probe() callbacks (previously __init) because
sysfs may cause them to be called later (Uwe Kleine-König)
- Prevent xHCI driver from claiming AMD VanGogh USB3 DRD device, so
it can be claimed by dwc3 instead (Vicki Pfau)
PCI device hotplug:
- Add Ampere Altra Attention Indicator extension driver for acpiphp
(D Scott Phillips)
Power management:
- Quirk VideoPropulsion Torrent QN16e with longer delay after reset
(Lukas Wunner)
- Prevent users from overriding drivers that say we shouldn't use
D3cold (Lukas Wunner)
- Avoid PME from D3hot/D3cold for AMD Rembrandt and Phoenix USB4
because wakeup interrupts from those states don't work if amd-pmc
has put the platform in a hardware sleep state (Mario Limonciello)
IOMMU:
- Disable ATS for Intel IPU E2000 devices with invalidation message
endianness erratum (Bartosz Pawlowski)
Error handling:
- Factor out interrupt enable/disable into helpers (Kai-Heng Feng)
Peer-to-peer DMA:
- Fix flexible-array usage in struct pci_p2pdma_pagemap in case we
ever use pagemaps with multiple entries (Gustavo A. R. Silva)
ASPM:
- Revert a change that broke when drivers disabled L1 and users later
enabled an L1.x substate via sysfs, and fix a similar issue when
users disabled L1 via sysfs (Heiner Kallweit)
Endpoint framework:
- Fix double free in __pci_epc_create() (Dan Carpenter)
- Use IS_ERR_OR_NULL() to simplify endpoint core (Ruan Jinjie)
Cadence PCIe controller driver:
- Drop unused "is_rc" member (Li Chen)
Freescale Layerscape PCIe controller driver:
- Enable 64-bit addressing in endpoint mode (Guanhua Gao)
Intel VMD host bridge driver:
- Fix multi-function header check (Ilpo Järvinen)
Microsoft Hyper-V host bridge driver:
- Annotate struct hv_dr_state with __counted_by (Kees Cook)
NVIDIA Tegra194 PCIe controller driver:
- Drop setting of LNKCAP_MLW (max link width) since dw_pcie_setup()
already does this via dw_pcie_link_set_max_link_width() (Yoshihiro
Shimoda)
Qualcomm PCIe controller driver:
- Use PCIE_SPEED2MBS_ENC() to simplify encoding of link speed
(Manivannan Sadhasivam)
- Add a .write_dbi2() callback so DBI2 register writes, e.g., for
setting the BAR size, work correctly (Manivannan Sadhasivam)
- Enable ASPM for platforms that use 1.9.0 ops, because the PCI core
doesn't enable ASPM states that haven't been enabled by the
firmware (Manivannan Sadhasivam)
Renesas R-Car Gen4 PCIe controller driver:
- Add DesignWare core support (set max link width, EDMA_UNROLL flag,
.pre_init(), .deinit(), etc) for use by R-Car Gen4 driver
(Yoshihiro Shimoda)
- Add driver and DT schema for DesignWare-based Renesas R-Car Gen4
controller in both host and endpoint mode (Yoshihiro Shimoda)
Xilinx NWL PCIe controller driver:
- Update ECAM size to support 256 buses (Thippeswamy Havalige)
- Stop setting bridge primary/secondary/subordinate bus numbers,
since PCI core does this (Thippeswamy Havalige)
Xilinx XDMA controller driver:
- Add driver and DT schema for Zynq UltraScale+ MPSoCs devices with
Xilinx XDMA Soft IP (Thippeswamy Havalige)
Miscellaneous:
- Use FIELD_GET()/FIELD_PREP() to simplify and reduce use of _SHIFT
macros (Ilpo Järvinen, Bjorn Helgaas)
- Remove logic_outb(), _outw(), outl() duplicate declarations (John
Sanpe)
- Replace unnecessary UTF-8 in Kconfig help text because menuconfig
doesn't render it correctly (Liu Song)"
* tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (102 commits)
PCI: qcom-ep: Add dedicated callback for writing to DBI2 registers
PCI: Simplify pcie_capability_clear_and_set_word() to ..._clear_word()
PCI: endpoint: Fix double free in __pci_epc_create()
PCI: xilinx-xdma: Add Xilinx XDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx XDMA PCIe Root Port Bridge
PCI: xilinx-cpm: Move IRQ definitions to a common header
PCI: xilinx-nwl: Modify ECAM size to enable support for 256 buses
PCI: xilinx-nwl: Rename the NWL_ECAM_VALUE_DEFAULT macro
dt-bindings: PCI: xilinx-nwl: Modify ECAM size in the DT example
PCI: xilinx-nwl: Remove redundant code that sets Type 1 header fields
PCI: hotplug: Add Ampere Altra Attention Indicator extension driver
PCI/AER: Factor out interrupt toggling into helpers
PCI: acpiphp: Allow built-in drivers for Attention Indicators
PCI/portdrv: Use FIELD_GET()
PCI/VC: Use FIELD_GET()
PCI/PTM: Use FIELD_GET()
PCI/PME: Use FIELD_GET()
PCI/ATS: Use FIELD_GET()
PCI/ATS: Show PASID Capability register width in bitmasks
PCI/ASPM: Fix L1 substate handling in aspm_attr_store_common()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs updates from Gao Xiang:
"Nothing exciting lands for this cycle, since we're still busying in
developing support for sub-page blocks and large-folios of compressed
data for new scenarios on Android.
In this cycle, MicroLZMA format is marked as stable, and there are
minor cleanups around documentation and codebase. In addition, it also
fixes incorrect lockref usage in erofs_insert_workgroup().
Summary:
- Fix inode metadata space layout documentation
- Avoid warning for MicroLZMA format anymore
- Fix erofs_insert_workgroup() lockref usage
- Some cleanups"
* tag 'erofs-for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix erofs_insert_workgroup() lockref usage
erofs: tidy up redundant includes
erofs: get rid of ROOT_NID()
erofs: simplify compression configuration parser
erofs: don't warn MicroLZMA format anymore
erofs: fix inode metadata space layout description in documentation
|
|
Pull documentation updates from Jonathan Corbet:
"The number of commits for documentation is not huge this time around,
but there are some significant changes nonetheless:
- Some more Spanish-language and Chinese translations
- The much-discussed documentation of the confidential-computing
threat model
- Powerpc and RISCV documentation move under Documentation/arch -
these complete this particular bit of documentation churn
- A large traditional-Chinese documentation update
- A new document on backporting and conflict resolution
- Some kernel-doc and Sphinx fixes
Plus the usual smattering of smaller updates and typo fixes"
* tag 'docs-6.7' of git://git.lwn.net/linux: (40 commits)
scripts/kernel-doc: Fix the regex for matching -Werror flag
docs: backporting: address feedback
Documentation: driver-api: pps: Update PPS generator documentation
speakup: Document USB support
doc: blk-ioprio: Bring the doc in line with the implementation
docs: usb: fix reference to nonexistent file in UVC Gadget
docs: doc-guide: mention 'make refcheckdocs'
Documentation: fix typo in dynamic-debug howto
scripts/kernel-doc: match -Werror flag strictly
Documentation/sphinx: Remove the repeated word "the" in comments.
docs: sparse: add SPDX-License-Identifier
docs/zh_CN: Add subsystem-apis Chinese translation
docs/zh_TW: update contents for zh_TW
docs: submitting-patches: encourage direct notifications to commenters
docs: add backporting and conflict resolution document
docs: move riscv under arch
docs: update link to powerpc/vmemmap_dedup.rst
mm/memory-hotplug: fix typo in documentation
docs: move powerpc under arch
PCI: Update the devres documentation regarding to pcim_*()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest updates from Shuah Khan:
- kbuild kselftest-merge target fixes
- fixes to several tests
- resctrl test fixes and enhancements
- ksft_perror() helper and reporting improvements
- printf attribute to kselftest prints to improve reporting
- documentation and clang build warning fixes
The bulk of the patches are for resctrl fixes and enhancements.
* tag 'linux_kselftest-next-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (51 commits)
selftests/resctrl: Fix MBM test failure when MBA unavailable
selftests/clone3: Report descriptive test names
selftests:modify the incorrect print format
selftests/efivarfs: create-read: fix a resource leak
selftests/ftrace: Add riscv support for kprobe arg tests
selftests/ftrace: add loongarch support for kprobe args char tests
selftests/amd-pstate: Added option to provide perf binary path
selftests/amd-pstate: Fix broken paths to run workloads in amd-pstate-ut
selftests/resctrl: Move run_benchmark() to a more fitting file
selftests/resctrl: Fix schemata write error check
selftests/resctrl: Reduce failures due to outliers in MBA/MBM tests
selftests/resctrl: Fix feature checks
selftests/resctrl: Refactor feature check to use resource and feature name
selftests/resctrl: Move _GNU_SOURCE define into Makefile
selftests/resctrl: Remove duplicate feature check from CMT test
selftests/resctrl: Extend signal handler coverage to unmount on receiving signal
selftests/resctrl: Fix uninitialized .sa_flags
selftests/resctrl: Cleanup benchmark argument parsing
selftests/resctrl: Remove ben_count variable
selftests/resctrl: Make benchmark command const and build it with pointers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull bootconfig updates from Masami Hiramatsu:
- Documentation update for /proc/cmdline, which includes both the
parameters from bootloader and the embedded parameters in the kernel
- fs/proc: Add bootloader argument as a comment line to
/proc/bootconfig so that the user can distinguish what parameters
were passed from bootloader even if bootconfig modified that
- Documentation fix to add /proc/bootconfig to proc.rst
* tag 'bootconfig-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
doc: Add /proc/bootconfig to proc.rst
fs/proc: Add boot loader arguments as comment to /proc/bootconfig
doc: Update /proc/cmdline documentation to include boot config
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull ia64 removal and asm-generic updates from Arnd Bergmann:
- The ia64 architecture gets its well-earned retirement as planned,
now that there is one last (mostly) working release that will be
maintained as an LTS kernel.
- The architecture specific system call tables are updated for the
added map_shadow_stack() syscall and to remove references to the
long-gone sys_lookup_dcookie() syscall.
* tag 'asm-generic-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
hexagon: Remove unusable symbols from the ptrace.h uapi
asm-generic: Fix spelling of architecture
arch: Reserve map_shadow_stack() syscall number for all architectures
syscalls: Cleanup references to sys_lookup_dcookie()
Documentation: Drop or replace remaining mentions of IA64
lib/raid6: Drop IA64 support
Documentation: Drop IA64 from feature descriptions
kernel: Drop IA64 support from sig_fault handlers
arch: Remove Itanium (IA-64) architecture
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"The highlights for the driver support this time are
- Qualcomm platforms gain support for the Qualcomm Secure Execution
Environment firmware interface to access EFI variables on certain
devices, and new features for multiple platform and firmware
drivers.
- Arm FF-A firmware support gains support for v1.1 specification
features, in particular notification and memory transaction
descriptor changes.
- SCMI firmware support now support v3.2 features for clock and DVFS
configuration and a new transport for Qualcomm platforms.
- Minor cleanups and bugfixes are added to pretty much all the active
platforms: qualcomm, broadcom, dove, ti-k3, rockchip, sifive,
amlogic, atmel, tegra, aspeed, vexpress, mediatek, samsung and
more.
In particular, this contains portions of the treewide conversion to
use __counted_by annotations and the device_get_match_data helper"
* tag 'soc-drivers-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (156 commits)
soc: qcom: pmic_glink_altmode: Print return value on error
firmware: qcom: scm: remove unneeded 'extern' specifiers
firmware: qcom: scm: add a missing forward declaration for struct device
firmware: qcom: move Qualcomm code into its own directory
soc: samsung: exynos-chipid: Convert to platform remove callback returning void
soc: qcom: apr: Add __counted_by for struct apr_rx_buf and use struct_size()
soc: qcom: pmic_glink: fix connector type to be DisplayPort
soc: ti: k3-socinfo: Avoid overriding return value
soc: ti: k3-socinfo: Fix typo in bitfield documentation
soc: ti: knav_qmss_queue: Use device_get_match_data()
firmware: ti_sci: Use device_get_match_data()
firmware: qcom: qseecom: add missing include guards
soc/pxa: ssp: Convert to platform remove callback returning void
soc/mediatek: mtk-mmsys: Convert to platform remove callback returning void
soc/mediatek: mtk-devapc: Convert to platform remove callback returning void
soc/loongson: loongson2_guts: Convert to platform remove callback returning void
soc/litex: litex_soc_ctrl: Convert to platform remove callback returning void
soc/ixp4xx: ixp4xx-qmgr: Convert to platform remove callback returning void
soc/ixp4xx: ixp4xx-npe: Convert to platform remove callback returning void
soc/hisilicon: kunpeng_hccs: Convert to platform remove callback returning void
...
|
|
Pull SoC DT updates from Arnd Bergmann:
"There are a couple new SoCs that are supported for the first time:
- AMD Pensando Elba is a data processing unit based on Cortex-A72 CPU
cores
- Sophgo makes RISC-V based chips, and we now support the CV1800B
chip used in the milkv-duo board and the massive sg2042 chip in the
milkv-pioneer, a 64-core developer workstation.
- Qualcomm Snapdragon 720G (sm7125) is a close relative of Snapdragon
7c and gets added with some Xiaomi phones
- Renesas gains support for the R8A779F4 (R-Car S4-8) automotive SoC
and the RZ/G3S (R9A08G045) embedded SoC.
There are also a bunch of newly supported machines that use already
supported chips. On the 32-bit side, we have:
- USRobotics USR8200 is a NAS/Firewall/router based on the ancient
Intel IXP4xx platform
- A couple of machines based on the NXP i.MX5 and i.MX6 platforms
- One machine each for Allwinner V3s, Aspeed AST2600, Microchip
sama5d29 and ST STM32mp157
The other ones all use arm64 cores on chips from allwinner, amlogic,
freescale, mediatek, qualcomm and rockchip"
* tag 'soc-dt-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (641 commits)
ARM: dts: BCM5301X: Set switch ports for Linksys EA9200
ARM: dts: BCM5301X: Set fixed-link for extra Netgear R8000 CPU ports
ARM: dts: BCM5301X: Explicitly disable unused switch CPU ports
ARM: dts: BCM5301X: Relicense Vivek's code to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Relicense Felix's code to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Set MAC address for Asus RT-AC87U
arm64: dts: socionext: add missing cache properties
riscv: dts: thead: convert isa detection to new properties
arm64: dts: Update cache properties for socionext
arm64: dts: ti: k3-am654-idk: Add ICSSG Ethernet ports
arm64: dts: ti: k3-am654-icssg2: add ICSSG2 Ethernet support
arm64: dts: ti: k3-am65-main: Add ICSSG IEP nodes
arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM
arm64: dts: ti: k3-am62p: Add nodes for more IPs
arm64: dts: rockchip: Add Turing RK1 SoM support
dt-bindings: arm: rockchip: Add Turing RK1
dt-bindings: vendor-prefixes: add turing
arm64: dts: rockchip: Add DFI to rk3588s
arm64: dts: rockchip: Add DFI to rk356x
arm64: dts: rockchip: Always enable DFI on rk3399
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain updates from Ulf Hansson:
- Move Kconfig files into the pmdomain subsystem
- Drop use of genpd's redundant ->opp_to_performance_state() callback
- amlogic:
- Add support for the T7 power-domains controller
- Fix mask for the second NNA mem power-domain
- bcm: Fixup ASB register read and comparison for bcm2835-power
- imx: Fix device link problem for consumers of the pgc power-domain
- mediatek: Add support for the MT8365 power domains
- qcom:
- Add support for the rpmhpds for SC8380XP power-domains
- Add support for the rpmhpds for SM8650 power-domains
- Add support for the rpmhpd clocks for SM7150
- Add support for the rpmpds for MSM8917 (families) power-domains
- starfive: Add support for the JH7110 AON PMU
* tag 'pmdomain-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm: (56 commits)
pmdomain: amlogic: Fix mask for the second NNA mem PD domain
pmdomain: qcom: rpmhpd: Add SC8380XP power domains
pmdomain: qcom: rpmhpd: Add SM8650 RPMh Power Domains
dt-bindings: power: rpmpd: Add SC8380XP support
dt-bindings: power: qcom,rpmhpd: Add GMXC PD index
dt-bindings: power: qcom,rpmpd: document the SM8650 RPMh Power Domains
pmdomain: imx: Make imx pgc power domain also set the fwnode
pmdomain: qcom: rpmpd: Add QM215 power domains
pmdomain: qcom: rpmpd: Add MSM8917 power domains
dt-bindings: power: rpmpd: Add MSM8917, MSM8937 and QM215
pmdomain: bcm: bcm2835-power: check if the ASB register is equal to enable
pmdomain: qcom: rpmhpd: Drop the ->opp_to_performance_state() callback
pmdomain: qcom: rpmpd: Drop the ->opp_to_performance_state() callback
pmdomain: qcom: cpr: Drop the ->opp_to_performance_state() callback
pmdomain: Use device_get_match_data()
pmdomain: ti: add missing of_node_put
pmdomain: mediatek: Add support for MT8365
pmdomain: mediatek: Add support for MTK_SCPD_STRICT_BUS_PROTECTION cap
pmdomain: mediatek: Add support for WAY_EN operations
pmdomain: mediatek: Unify configuration for infracfg and smi
...
|
|
Pull MMC updates from Ulf Hansson:
" MMC core:
- Enable host caps to be modified via debugfs to test speed-modes
- Improve random I/O writes for 4k buffers for hsq enabled hosts
MMC host:
- atmel-mci/sdhci-of-at91: Aubin Constans takes over as maintainer
- dw_mmc-starfive: Re-work tuning support
- meson-gx: Fix bogus IRQ when using CMD_CFG_ERROR
- mmci: Use peripheral flow control for the STM32 variant
- renesas,sdhi: Add support for the RZ/G3S variant
- sdhci-esdhc-imx: Optimize the manual tuning logic
- sdhci-msm: Add support for the SM8650 variant
- sdhci-npcm: Add driver to support the Nuvoton NPCM BMC variant
- sdhci-pci-gli: Add workaround to allow GL9750 to enter ASPM L1.2"
* tag 'mmc-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (25 commits)
dt-bindings: mmc: sdhci-msm: document the SM8650 SDHCI Controller
mmc: meson-gx: Remove setting of CMD_CFG_ERROR
MAINTAINERS: mmc: take over as maintainer of MCI & SDHCI MICROCHIP DRIVERS
mmc: jz4740: Use device_get_match_data()
mmc: sdhci-npcm: Add NPCM SDHCI driver
dt-bindings: mmc: npcm,sdhci: Document NPCM SDHCI controller
mmc: sdhci-pltfm: Make driver OF independent
mmc: sdhci-pltfm: Drop unnecessary error messages in sdhci_pltfm_init()
mmc: sdhci-pci: Switch to use acpi_evaluate_dsm_typed()
mmc: debugfs: Allow host caps to be modified
mmc: core: Always reselect card type
mmc: mmci: use peripheral flow control for STM32
mmc: vub300: replace deprecated strncpy with strscpy
memstick: jmb38x_ms: Annotate struct jmb38x_ms with __counted_by
mmc: starfive: Change tuning implementation
dt-bindings: mmc: starfive: Remove properties from required
mmc: hsq: Improve random I/O write performance for 4k buffers
mmc: core: Allow dynamical updates of the number of requests for hsq
mmc: sdhci-pci-gli: A workaround to allow GL9750 to enter ASPM L1.2
dt-bindings: mmc: renesas,sdhi: Document RZ/G3S support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA updates from Damien Le Moal:
- Modify the AHCI driver to print the link power management policy used
on scan, to help with debugging issues (Niklas)
- Add support for the ASM2116 series adapters to the AHCI driver
(Szuying)
- Prepare libata for the coming gcc and Clang __counted_by attribute
(Kees)
- Following the recent estensive fixing of libata suspend/resume
handling, several patches further cleanup and improve disk power
state management (me)
- Reduce the verbosity of some error messages for non-fatal temporary
errors, e.g. slow response to device reset when scanning a port, and
warning messages that are in fact normal, e.g. disabling a device on
suspend or when removing it (me)
- Cleanup DMA helper functions (me)
- Fix sata_mv drive handling of potential errors durring probe (Ma)
- Cleanup the xgene and imx drivers using the functions
of_device_get_match_data() and device_get_match_data() (Rob)
- Improve the tegra driver device tree (Rob)
* tag 'ata-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (22 commits)
dt-bindings: ata: tegra: Disallow undefined properties
ata: libata-core: Improve ata_dev_power_set_active()
ata: libata-eh: Spinup disk on resume after revalidation
ata: imx: Use device_get_match_data()
ata: xgene: Use of_device_get_match_data()
ata: sata_mv: aspeed: fix value check in mv_platform_probe()
ata: ahci: Add Intel Alder Lake-P AHCI controller to low power chipsets list
ata: libata: Cleanup inline DMA helper functions
ata: libata-eh: Reduce "disable device" message verbosity
ata: libata-eh: Improve reset error messages
ata: libata-sata: Improve ata_sas_slave_configure()
ata: libata-core: Do not resume runtime suspended ports
ata: libata-core: Do not poweroff runtime suspended ports
ata: libata-core: Remove ata_port_resume_async()
ata: libata-core: Remove ata_port_suspend_async()
ata: libata-core: Detach a port devices on shutdown
ata: libata-core: Synchronize ata_port_detach() with hotplug
ata: libata-scsi: Cleanup ata_scsi_start_stop_xlat()
scsi: Remove scsi device no_start_on_resume flag
ata: libata: Annotate struct ata_cpr_log with __counted_by
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"No major architecture features this time around, just some new HWCAP
definitions, support for the Ampere SoC PMUs and a few fixes/cleanups.
The bulk of the changes is reworking of the CPU capability checking
code (cpus_have_cap() etc).
- Major refactoring of the CPU capability detection logic resulting
in the removal of the cpus_have_const_cap() function and migrating
the code to "alternative" branches where possible
- Backtrace/kgdb: use IPIs and pseudo-NMI
- Perf and PMU:
- Add support for Ampere SoC PMUs
- Multi-DTC improvements for larger CMN configurations with
multiple Debug & Trace Controllers
- Rework the Arm CoreSight PMU driver to allow separate
registration of vendor backend modules
- Fixes: add missing MODULE_DEVICE_TABLE to the amlogic perf
driver; use device_get_match_data() in the xgene driver; fix
NULL pointer dereference in the hisi driver caused by calling
cpuhp_state_remove_instance(); use-after-free in the hisi driver
- HWCAP updates:
- FEAT_SVE_B16B16 (BFloat16)
- FEAT_LRCPC3 (release consistency model)
- FEAT_LSE128 (128-bit atomic instructions)
- SVE: remove a couple of pseudo registers from the cpufeature code.
There is logic in place already to detect mismatched SVE features
- Miscellaneous:
- Reduce the default swiotlb size (currently 64MB) if no ZONE_DMA
bouncing is needed. The buffer is still required for small
kmalloc() buffers
- Fix module PLT counting with !RANDOMIZE_BASE
- Restrict CPU_BIG_ENDIAN to LLVM IAS 15.x or newer move
synchronisation code out of the set_ptes() loop
- More compact cpufeature displaying enabled cores
- Kselftest updates for the new CPU features"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (83 commits)
arm64: Restrict CPU_BIG_ENDIAN to GNU as or LLVM IAS 15.x or newer
arm64: module: Fix PLT counting when CONFIG_RANDOMIZE_BASE=n
arm64, irqchip/gic-v3, ACPI: Move MADT GICC enabled check into a helper
perf: hisi: Fix use-after-free when register pmu fails
drivers/perf: hisi_pcie: Initialize event->cpu only on success
drivers/perf: hisi_pcie: Check the type first in pmu::event_init()
arm64: cpufeature: Change DBM to display enabled cores
arm64: cpufeature: Display the set of cores with a feature
perf/arm-cmn: Enable per-DTC counter allocation
perf/arm-cmn: Rework DTC counters (again)
perf/arm-cmn: Fix DTC domain detection
drivers: perf: arm_pmuv3: Drop some unused arguments from armv8_pmu_init()
drivers: perf: arm_pmuv3: Read PMMIR_EL1 unconditionally
drivers/perf: hisi: use cpuhp_state_remove_instance_nocalls() for hisi_hns3_pmu uninit process
clocksource/drivers/arm_arch_timer: limit XGene-1 workaround
arm64: Remove system_uses_lse_atomics()
arm64: Mark the 'addr' argument to set_ptes() and __set_pte_at() as unused
drivers/perf: xgene: Use device_get_match_data()
perf/amlogic: add missing MODULE_DEVICE_TABLE
arm64/mm: Hoist synchronization out of set_ptes() loop
...
|
|
Pull drm updates from Dave Airlie:
"Highlights:
- AMD adds some more upcoming HW platforms
- Intel made Meteorlake stable and started adding Lunarlake
- nouveau has a bunch of display rework in prepartion for the NVIDIA
GSP firmware support
- msm adds a7xx support
- habanalabs has finished migration to accel subsystem
Detail summary:
kernel:
- add initial vmemdup-user-array
core:
- fix platform remove() to return void
- drm_file owner updated to reflect owner
- move size calcs to drm buddy allocator
- let GPUVM build as a module
- allow variable number of run-queues in scheduler
edid:
- handle bad h/v sync_end in EDIDs
panfrost:
- add Boris as maintainer
fbdev:
- use fb_ops helpers more
- only allow logo use from fbcon
- rename fb_pgproto to pgprot_framebuffer
- add HPD state to drm_connector_oob_hotplug_event
- convert to fbdev i/o mem helpers
i915:
- Enable meteorlake by default
- Early Xe2 LPD/Lunarlake display enablement
- Rework subplatforms into IP version checks
- GuC based TLB invalidation for Meteorlake
- Display rework for future Xe driver integration
- LNL FBC features
- LNL display feature capability reads
- update recommended fw versions for DG2+
- drop fastboot module parameter
- added deviceid for Arrowlake-S
- drop preproduction workarounds
- don't disable preemption for resets
- cleanup inlines in headers
- PXP firmware loading fix
- Fix sg list lengths
- DSC PPS state readout/verification
- Add more RPL P/U PCI IDs
- Add new DG2-G12 stepping
- DP enhanced framing support to state checker
- Improve shared link bandwidth management
- stop using GEM macros in display code
- refactor related code into display code
- locally enable W=1 warnings
- remove PSR watchdog timers on LNL
amdgpu:
- RAS/FRU EEPROM updatse
- IP discovery updatses
- GC 11.5 support
- DCN 3.5 support
- VPE 6.1 support
- NBIO 7.11 support
- DML2 support
- lots of IP updates
- use flexible arrays for bo list handling
- W=1 fixes
- Enable seamless boot in more cases
- Enable context type property for HDMI
- Rework GPUVM TLB flushing
- VCN IB start/size alignment fixes
amdkfd:
- GC 10/11 fixes
- GC 11.5 support
- use partial migration in GPU faults
radeon:
- W=1 Fixes
- fix some possible buffer overflow/NULL derefs
nouveau:
- update uapi for NO_PREFETCH
- scheduler/fence fixes
- rework suspend/resume for GSP-RM
- rework display in preparation for GSP-RM
habanalabs:
- uapi: expose tsc clock
- uapi: block access to eventfd through control device
- uapi: force dma-buf export to PAGE_SIZE alignments
- complete move to accel subsystem
- move firmware interface include files
- perform hard reset on PCIe AXI drain event
- optimise user interrupt handling
msm:
- DP: use existing helpers for DPCD
- DPU: interrupts reworked
- gpu: a7xx (a730/a740) support
- decouple msm_drv from kms for headless devices
mediatek:
- MT8188 dsi/dp/edp support
- DDP GAMMA - 12 bit LUT support
- connector dynamic selection capability
rockchip:
- rv1126 mipi-dsi/vop support
- add planar formats
ast:
- rename constants
panels:
- Mitsubishi AA084XE01
- JDI LPM102A188A
- LTK050H3148W-CTA6
ivpu:
- power management fixes
qaic:
- add detach slice bo api
komeda:
- add NV12 writeback
tegra:
- support NVSYNC/NHSYNC
- host1x suspend fixes
ili9882t:
- separate into own driver"
* tag 'drm-next-2023-10-31-1' of git://anongit.freedesktop.org/drm/drm: (1803 commits)
drm/amdgpu: Remove unused variables from amdgpu_show_fdinfo
drm/amdgpu: Remove duplicate fdinfo fields
drm/amd/amdgpu: avoid to disable gfxhub interrupt when driver is unloaded
drm/amdgpu: Add EXT_COHERENT support for APU and NUMA systems
drm/amdgpu: Retrieve CE count from ce_count_lo_chip in EccInfo table
drm/amdgpu: Identify data parity error corrected in replay mode
drm/amdgpu: Fix typo in IP discovery parsing
drm/amd/display: fix S/G display enablement
drm/amdxcp: fix amdxcp unloads incompletely
drm/amd/amdgpu: fix the GPU power print error in pm info
drm/amdgpu: Use pcie domain of xcc acpi objects
drm/amd: check num of link levels when update pcie param
drm/amdgpu: Add a read to GFX v9.4.3 ring test
drm/amd/pm: call smu_cmn_get_smc_version in is_mode1_reset_supported.
drm/amdgpu: get RAS poison status from DF v4_6_2
drm/amdgpu: Use discovery table's subrevision
drm/amd/display: 3.2.256
drm/amd/display: add interface to query SubVP status
drm/amd/display: Read before writing Backlight Mode Set Register
drm/amd/display: Disable SYMCLK32_SE RCO on DCN314
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Add a kselftest to check for unprobed DT devices
- Fix address translation for some 3 address cells cases
- Refactor firmware node refcounting for AMBA bus
- Add bindings for qcom,sm4450-pdc, Qualcomm Kryo 465 CPU, and
Freescale QMC HDLC
- Add Marantec vendor prefix
- Convert qcom,pm8921-keypad, cnxt,cx92755-wdt, da9062-wdt, and
atmel,at91rm9200-wdt bindings to DT schema
- Several additionalProperties/unevaluatedProperties on child node
schemas fixes
- Drop reserved-memory bindings which now live in dtschema project
- Fix a reference to rockchip,inno-usb2phy.yaml
- Remove backlight nodes from display panel examples
- Expand example for using DT_SCHEMA_FILES
- Merge simple LVDS panel bindings to one binding doc
* tag 'devicetree-for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (34 commits)
dt-bindings: soc: fsl: cpm_qe: cpm1-scc-qmc: Add support for QMC HDLC
dt-bindings: soc: fsl: cpm_qe: cpm1-scc-qmc: Add 'additionalProperties: false' in child nodes
dt-bindings: soc: fsl: cpm_qe: cpm1-scc-qmc: Fix example property name
dt-bindings: arm,coresight-cti: Add missing additionalProperties on child nodes
dt-bindings: arm,coresight-cti: Drop type for 'cpu' property
dt-bindings: soundwire: Add reference to soundwire-controller.yaml schema
dt-bindings: input: syna,rmi4: Make "additionalProperties: true" explicit
media: dt-bindings: ti,ds90ub960: Add missing type for "i2c-alias"
dt-bindings: input: qcom,pm8921-keypad: convert to YAML format
of: overlay: unittest: overlay_bad_unresolved: Spelling s/ok/okay/
of: address: Consolidate bus .map() functions
of: address: Store number of bus flag cells rather than bool
of: unittest: Add tests for address translations
of: address: Remove duplicated functions
of: address: Fix address translation when address-size is greater than 2
dt-bindings: watchdog: cnxt,cx92755-wdt: convert txt to yaml
dt-bindings: watchdog: da9062-wdt: convert txt to yaml
dt-bindings: watchdog: fsl,scu-wdt: Document imx8dl
dt-bindings: watchdog: atmel,at91rm9200-wdt: convert txt to yaml
dt-bindings: usb: rockchip,dwc3: update inno usb2 phy binding name
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core changes:
- propagate of_node to child device
- change from atomic to blocking notifier_call_chain
New drivers:
- pm8916 battery management system
- mm8013 fuel gauge
New features:
- maxim max17040: add temperature support
- gpio-poweroff: make priority configurable
Cleanups:
- simplify reset drivers using builtin_platform_driver()
- convert all platform drivers to remove_new callback
- replace all strncpy occurrences with strscpy
- started converting drivers to i2c_get_match_data()
- misc fixes and cleanups"
* tag 'for-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (91 commits)
power: reset: vexpress: Use device_get_match_data()
power: supply: surface-charger: replace deprecated strncpy with strscpy
power: supply: surface_battery: replace deprecated strncpy with strscpy
power: supply: charger-manager: replace deprecated strncpy with strscpy
power: supply: bq25980: replace deprecated strncpy with strscpy
power: supply: bq256xx: replace deprecated strncpy with strscpy
power: supply: bq2515x: replace deprecated strncpy with strscpy
power: supply: bq24190_charger: replace deprecated strncpy with strscpy
power: supply: cpcap: Drop non-DT driver matching
power: reset: brcmstb: Depend on actual SoC dependencies
power: reset: gpio-poweroff: make sys handler priority configurable
dt-bindings: power: reset: gpio-poweroff: Add priority property
power: reset: gpio-poweroff: use sys-off handler API
power: reset: gpio-poweroff: use a struct to store the module variables
power: supply: rt5033_charger: Replace "&pdev->dev" by "charger->dev" in probe
power: supply: rt5033_charger: Simplify initialization of rt5033_charger_data
power: supply: rt5033_charger: Add cable detection and USB OTG supply
power: supply: core: remove opencoded string_lower()
dt-bindings: power: supply: sbs-manager: Add missing unevaluatedProperties on child node schemas
power: supply: mm8013: Fix an error checking issue in mm8013_checkdevice()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk driver updates from Stephen Boyd:
"Herein lies a smallish collection of clk driver updates and some core
clk framework changes for the merge window. The core framework changes
are only improving the debugfs interface to allow phase adjustments
and report which consumers of a clk there are. These are most likely
only of interest to kernel developers.
On the clk driver side, it's a ghastly amount of updates with only a
handful of new clk drivers. We have a couple new clk drivers for
Qualcomm, per usual, and a driver for Renesas, Amlogic, and TI
respectively. The updates are spread throughout the clk drivers.
Some highlights are fixing kunit tests for different configurations
like lockdep and big-endian, avoiding integer overflow in rate
settable clks, moving clk_hw_onecell_data to the end of allocations so
that drivers don't corrupt their private data, and migrating clk
drivers to the regmap maple tree. Otherwise it's the usual fixes to
clk drivers that only come along with testing the drivers on real
hardware.
New Drivers:
- Add clock driver for TWL6032
- Initial support for the Qualcomm SM4450 Global Clock Controller and
SM4450 RPMh clock controllers
- Add Camera Clock Controller on Qualcomm SM8550
- Add support for the Renesas RZ/G3S (R9A08G045) SoC
- Add Amlogic s4 main clock controller support
Updates:
- Make clk kunit tests work with lockdep
- Fix clk gate kunit test for big-endian
- Convert more than a handful of clk drivers to use regmap maple tree
- Consider the CLK_FRAC_DIVIDER_ZERO_BASED in fractional divider clk
implementation
- Add consumer info to clk debugfs
- Fix various clk drivers that have clk_hw_onecell_data not at the
end of an allocation
- Drop CLK_SET_RATE_PARENT for clocks with fixed-rate GPLLs across a
variety of Qualcomm IPQ platforms
- Add missing parent of APCS PLL on Qualcomm IPQ6018
- Add I2C QUP6 clk on Qualcomm IPQ6018 but mark it critical to avoid
problems with RPM
- Implement safe source switching for a53pll and use on Qualcomm
IPQ5332
- Add support for Stromer Plus PLLs to Qualcomm clk driver
- Switch Qualcomm SM8550 Video and GPU clock controllers to use OLE
PLL configure method
- Non critical fixes to halt bit checks in Qualcomm clk drivers
- Add SMMU GDSC for Qualcomm MSM8998
- Fix possible integer overflow in Qualcomm RCG frequency calculation
code
- Remove RPM managed clks from Qualcomm MSM8996 GCC driver
- Add HFPLL configuration for the three HFPLLs in Qualcomm MSM8976
- Switch Qualcomm MSM8996 CBF clock driver's remove function to
return void
- Fix missing dependency for s4 clock controllers
- Select MXC_CLK when building in the CLK_IMX8QXP
- Fixes for error handling paths in i.MX8 ACM driver
- Move the clocks check in i.MX8 ACM driver in order to log any error
- Drop the unused return value of clk_imx_acm_detach_pm_domains
- Drop non-existant IMX8MP_CLK_AUDIOMIX_PDM_ROOT clock
- Fix error handling in i.MX8MQ clock driver
- Allow a different LCDIF1 clock parent if DT describes it for
i.MX6SX
- Keep the SCU resource table sorted in the i.MX8DXL rsrc driver
- Move the elcdif PLL clock registration above lcd_clk, as it is its
parent
- Correct some ENET specific clocks for i.MX8DXL platform
- Drop the VPU_UART and VPUCORE from i.MX8QM as latest HW revision
doesn't have them
- Remove "de-featured" MLB support from i.MX8QM/QXP/DXL platforms
- Skip registering clocks owned by Cortex-A partition SCU-based
platforms
- Add CAN_1/2 to i.MX8QM and M4_0, PI_0_PWM_0 and PI_0_I2C_0 to
i.MX8QXP resources"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (128 commits)
clk: Fix clk gate kunit test on big-endian CPUs
clk: si521xx: Increase stack based print buffer size in probe
clk: mediatek: fix double free in mtk_clk_register_pllfh()
clk: socfpga: agilex: Add bounds-checking coverage for struct stratix10_clock_data
clk: socfpga: Fix undefined behavior bug in struct stratix10_clock_data
clk: sifive: Allow building the driver as a module
clk: analogbits: Allow building the library as a module
clk: sprd: Composite driver support offset config
clk: Allow phase adjustment from debugfs
clk: Show active consumers of clocks in debugfs
clk: Use device_get_match_data()
clk: visconti: Add bounds-checking coverage for struct visconti_pll_provider
clk: visconti: Fix undefined behavior bug in struct visconti_pll_provider
clk: cdce925: Extend match support for OF tables
clk: si570: Simplify probe
clk: si5351: Simplify probe
clk: rs9: Use i2c_get_match_data() instead of device_get_match_data()
clk: clk-si544: Simplify probe() and is_valid_frequency()
clk: si521xx: Use i2c_get_match_data() instead of device_get_match_data()
clk: meson: S4: select CONFIG_COMMON_CLK_MESON_CLKC_UTILS
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Ilpo Järvinen:
- asus-wmi: Support for screenpad and solve brightness key press
duplication
- int3472: Eliminate the last use of deprecated GPIO functions
- mlxbf-pmc: New HW support
- msi-ec: Support new EC configurations
- thinkpad_acpi: Support reading aux MAC address during passthrough
- wmi: Fixes & improvements
- x86-android-tablets: Detection fix and avoid use of GPIO private APIs
- Debug & metrics interface improvements
- Miscellaneous cleanups / fixes / improvements
* tag 'platform-drivers-x86-v6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (80 commits)
platform/x86: inspur-platform-profile: Add platform profile support
platform/x86: thinkpad_acpi: Add battery quirk for Thinkpad X120e
platform/x86: wmi: Decouple WMI device removal from wmi_block_list
platform/x86: wmi: Fix opening of char device
platform/x86: wmi: Fix probe failure when failing to register WMI devices
platform/x86: wmi: Fix refcounting of WMI devices in legacy functions
platform/x86: wmi: Decouple probe deferring from wmi_block_list
platform/x86/amd/hsmp: Fix iomem handling
platform/x86: asus-wmi: Do not report brightness up/down keys when also reported by acpi_video
platform/x86: thinkpad_acpi: replace deprecated strncpy with memcpy
tools/power/x86/intel-speed-select: v1.18 release
tools/power/x86/intel-speed-select: Use cgroup isolate for CPU 0
tools/power/x86/intel-speed-select: Increase max CPUs in one request
tools/power/x86/intel-speed-select: Display error for core-power support
tools/power/x86/intel-speed-select: No TRL for non compute domains
tools/power/x86/intel-speed-select: turbo-mode enable disable swapped
tools/power/x86/intel-speed-select: Update help for TRL
tools/power/x86/intel-speed-select: Sanitize integer arguments
platform/x86: acer-wmi: Remove void function return
platform/x86/amd/pmc: Add dump_custom_stb module parameter
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Driver for LTC2991
- Driver for POWER-Z
Added chip / system support to existing drivers:
- The ina238 driver now also supports INA237
- The asus-ec-sensors driver now supports ROG Crosshair X670E Gene
- The aquacomputer_d5next now supports Aquacomputer High Flow USB and
MPS Flow
- The pmbus/mpq7932 driver now also supports MPQ2286
- The nct6683 now also supports ASRock X670E Taichi
Various other minor improvements and fixes:
- One patch series to call out is the conversion of hwmon platform
drivers to use the platform remove callback returning void"
* tag 'hwmon-for-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (69 commits)
hwmon: (aquacomputer_d5next) Check if temp sensors of legacy devices are connected
hwmon: (aquacomputer_d5next) Add support for Aquacomputer High Flow USB and MPS Flow
dt-bindings: hwmon: npcm: Add npcm845 compatible string
hwmon: Add driver for ltc2991
dt-bindings: hwmon: ltc2991: add bindings
hwmon: (pmbus/max31785) Add delay between bus accesses
hwmon: (ina238) add ina237 support
dt-bindings: hwmon: ti,ina2xx: add ti,ina237
hwmon: (asus-ec-sensors) add ROG Crosshair X670E Gene.
hwmon: (max31827) handle vref regulator
hwmon: (ina3221) Add support for channel summation disable
dt-bindings: hwmon: ina3221: Add ti,summation-disable
dt-bindings: hwmon: ina3221: Convert to json-schema
hwmon: (pmbus/mpq7932) Add a support for mpq2286 Power Management IC
hwmon: (pmbus/core) Add helper macro to define single pmbus regulator
regulator: dt-bindings: Add mps,mpq2286 power-management IC
hwmon: (pmbus/mpq7932) Get page count based on chip info
dt-bindings: hwmon: Add possible new properties to max31827 bindings
hwmon: (max31827) Modify conversion wait time
hwmon: (max31827) Make code cleaner
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This is a very quiet release for SPI, we've got cleanups and minor
fixes but only a few new driver specific features. The bulk of the
changes in terms of diffstat are the cleanups, plus one bit of
performance work for McSPI.
- Conversions to use devm_clk_get_enabled() and to remove outdated
terms for controller and device
- Device mode support for the Renesas CSI
- Cleanups and improvements to the device tree bindings aimed at
making validation better
- PIO FIFO usage for the OMAP2 McSPI, improving performance"
* tag 'spi-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (75 commits)
spi: omap2-mcspi: Add FIFO support without DMA
spi: stm32: Explicitly include correct DT includes
spi: Export acpi_spi_find_controller_by_adev()
spi: nxp-fspi: use the correct ioremap function
spi: Don't use flexible array in struct spi_message definition
spi: bcm2835: add a sentinel at the end of the lookup array
spi: spi-geni-qcom: Rename the label unmap_if_dma
spi: rzv2m-csi: Add target mode support
spi: renesas,rzv2m-csi: Add CSI (SPI) target related property
spi: spidev: make spidev_class constant
spi: mpc52xx-psc: Make mpc52xx_psc_spi_transfer_one_message() static
spi: spi-cadence-quadspi: Fix missing unwind goto warnings
spi: omap2-mcspi: Fix hardcoded reference clock
spi: dt-bindings: Make "additionalProperties: true" explicit
spi: at91-usart: Remove some dead code
spi: dt-bindings: st,stm32-spi: Move "st,spi-midi-ns" to spi-peripheral-props.yaml
spi: qup: Vote for interconnect bandwidth to DRAM
spi: dt-bindings: qup: Document interconnects
spi: qup: Parse OPP table for DVFS support
spi: dt-bindings: qup: Document power-domains and OPP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been a fairly quiet release for the regulator API, the
changes are dominated by some new drivers and a quite large set of
cleanups and filling in the blanks of features for the existing MT6358
driver.
- Cleanups and additional features for the Mediatek MT6358 driver
- Under voltage detection in the fixed regulator
- Support for Maxim MAX77503, Mediatek MT6366, Qualcomm PM8909,
PM8919, PMA8048 and PMC8380"
* tag 'regulator-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (45 commits)
regulator (max5970): Remove duplicate line
regulator (max5970): Add hwmon support
regulator: qcom-rpmh: Fix smps4 regulator for pm8550ve
regulator: qcom,rpmh: Add PMC8380 compatible
regulator: qcom-rpmh: Add regulators support for PMC8380
regulator: fixed: add support for under-voltage IRQ
regulator: dt-bindings: fixed-regulator: Add under-voltage interrupt support
dt-bindings: regulator: dlg,da9210: Convert to json-schema
regulator: dt-bindings: Add ADI MAX77503 support
regulator: max77503: Add ADI MAX77503 support
regulator: Use device_get_match_data()
regulator: da9121: Use i2c_get_match_data()
regulator: Drop unnecessary of_match_device() calls
regulator: da9063: Annotate struct da9063_regulators with __counted_by
regulator: da9062: Annotate struct da9062_regulators with __counted_by
regulator: mt6358: Add supply names for MT6366 regulators
regulator: mt6358: Add missing regulators for MT6366
regulator: mt6358: Make MT6366 vcn18 LDO configurable
regulator: mt6358: fix and drop type prefix in MT6366 regulator node names
regulator: mt6358: Add supply names for MT6358 regulators
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We don't have any new drivers. The loongson driver is getting extended
with support for new models. There's a big refactor of gpio-pca953x
and many small improvements to others.
The GPIO code in the kernel has acquired a lot of cruft over the years
as well as many abusers of the API across the kernel tree. This
release cycle we have started a major cleanup and improvement effort
that will most likely span several releases. We have started by
converting external users of struct gpio_chip to accessing the wrapper
around it - struct gpio_device. This is because the latter is
reference counted while the former is removed when the provider is
unbound. We also removed several instances of drivers accessing
private GPIOLIB structures and including the private header from
drivers/gpio/.
To that end you'll see several commits aimed at different subsystems
(acked by relevant maintainers) as well as two merges from the
x86/platform tree.
We'll then rework the locking in GPIOLIB which currently uses a big
spinlock for many different things and could use becoming more
fine-grained, especially as it doesn't even get the locking right.
We'll also use SRCU for protecting the gpio_chip pointer against
in-kernel hot-unplug crashes similar to what we saw triggered from
user-space and fixed with semaphores in gpiolib-cdev. The core GPIOLIB
is still vulnerable to these use-cases. I'm just mentioning the plans
here, this is not part of this PR.
You'll see some new instances of using __free(). We've added a
gpio_device_put cleanup helper similar to the put_device one
introduced by Peter Zijlstra and used it according to the preferred
pattern except where it didn't make sense.
GPIOLIB core:
- provide interfaces allowing users to retrieve, manage and query the
reference counted GPIO device instead of accessing the private
gpio_chip structure
- replace gpiochip_find() with gpio_device_find()
- remove unused acpi_get_and_request_gpiod()
- improve the ignore_interrupt functionality in GPIO ACPI
- correct notifier return codes in gpiolib-of
- unexport gpiod_set_transitory() as it's unused outside of core GPIO
code
- while there are still external users accessing struct gpio_chip,
let's make gpiochip_get_desc() public so that they at least use the
preferred helper
- improve locking for lookup tables
- annotate struct linereq with __counted_by
- improve GPIOLIB docs
- add an OF quirk for LED trigger sources
Driver improvements:
- convert all GPIO drivers with .remove() callbacks to using the new
variant returning void instead of int
- stop accessing the GPIOLIB private structures in gpio-mockup,
i2c-mux-gpio, hte-tegra194, gpio-sim
- use the recommended pattern for autofree variables in gpio-sim
- add support for more models to gpio-loongson
- use a notifier chain to notify other blocks about interrupts in
gpio-eic-sprd instead of looking up GPIO devices on every interrupt
- convert gpio-pca953x and gpio-fx6408 to using the maple tree regmap
cache
- don't include GPIOLIB internal headers in drivers which don't need
them
- move the ingenic NAND quirk into gpiolib-of
- add an ignore interrupt quirk for Peaq C1010
- drop static GPIO base from gpio-omap, gpio-f7188x
- use the preferred device_get_match_data() function in drivers that
still don't
- refactor gpio-pca953x: switch to using DEFINE_SIMPLE_DEV_PM_OPS(),
use cleanup helpers, use dev_err_probe() where it makes sense,
fully convert to using devres and some other minor tweaks
DT bindings:
- add support for a new model to gpio-vf610 and update existing
properties
- add support for more loongson models
- add missing support for imx models that are used but undocumented
- convert bindings for Intel IXP4xx to schema
Minor stuff:
- deprecate gpio-mockup in favor of gpio-sim
- include missing headers here and there
- stop using gpiochip_find() in OMAP1 board files
- minor tweaks in gpio-vf610, gpio-hisi
- remove unneeded 'extern' specifiers from headers"
* tag 'gpio-updates-for-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (108 commits)
hte: tegra194: add GPIOLIB dependency
hte: tegra194: don't access struct gpio_chip
gpiolib: provide gpio_device_get_base()
i2c: mux: gpio: don't fiddle with GPIOLIB internals
gpiolib: provide gpiod_to_gpio_device()
gpiolib: provide gpio_device_to_device()
gpio: hisi: Fix format specifier
gpiolib: provide gpio_device_find_by_fwnode()
gpio: acpi: remove acpi_get_and_request_gpiod()
gpio: Use device_get_match_data()
gpio: vf610: update comment for i.MX8ULP and i.MX93 legacy compatibles
platform/x86: int3472: Switch to devm_get_gpiod()
platform/x86: int3472: Stop using gpiod_toggle_active_low()
platform/x86: int3472: Add new skl_int3472_gpiod_get_from_temp_lookup() helper
platform/x86: int3472: Add new skl_int3472_fill_gpiod_lookup() helper
gpio: vf610: simplify code by dropping data check
gpio: vf610: add i.MX8ULP of_device_id entry
dt-bindings: gpio: vf610: add i.MX95 compatible
dt-bindings: gpio: vf610: correct i.MX8ULP and i.MX93
dt-bindings: gpio: vf610: update gpio-ranges
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add new hardware support (new Qualcomm SoC versions in cpufreq,
RK3568/RK3588 in devfreq), extend the OPP (operating performance
points) framework, improve cpufreq governors, fix issues and clean up
code (most of the changes are in cpufreq and devfreq).
Specifics:
- Add support for several Qualcomm SoC versions and other similar
changes (Christian Marangi, Dmitry Baryshkov, Luca Weiss, Neil
Armstrong, Richard Acayan, Robert Marko, Rohit Agarwal, Stephan
Gerhold and Varadarajan Narayanan)
- Clean up the tegra cpufreq driver (Sumit Gupta)
- Use of_property_read_reg() to parse "reg" in pmac32 driver (Rob
Herring)
- Add support for TI's am62p5 Soc (Bryan Brattlof)
- Make ARM_BRCMSTB_AVS_CPUFREQ depends on !ARM_SCMI_CPUFREQ (Florian
Fainelli)
- Update Kconfig to mention i.MX7 as well (Alexander Stein)
- Revise global turbo disable check in intel_pstate (Srinivas
Pandruvada)
- Carry out initialization of sg_cpu in the schedutil cpufreq
governor in one loop (Liao Chang)
- Simplify the condition for storing 'down_threshold' in the
conservative cpufreq governor (Liao Chang)
- Use fine-grained mutex in the userspace cpufreq governor (Liao
Chang)
- Move is_managed indicator in the userspace cpufreq governor into a
per-policy structure (Liao Chang)
- Rebuild sched-domains when removing cpufreq driver (Pierre Gondois)
- Fix buffer overflow detection in trans_stats() (Christian Marangi)
- Switch to dev_pm_opp_find_freq_(ceil/floor)_indexed() APIs to
support specific devices like UFS which handle multiple clocks
through OPP (Operating Performance Point) framework (Manivannan
Sadhasivam)
- Add perf support to the Rockchip DFI (DDR Monitor Module) devfreq-
event driver:
* Generalize rockchip-dfi.c to support new RK3568/RK3588 using
different DDR type (Sascha Hauer).
* Convert DT binding document format to yaml (Sascha Hauer).
* Add perf support for DFI (a unit suitable for measuring DDR
utilization) to rockchip-dfi.c to extend DFI usage (Sascha
Hauer)
- Add locking to the OPP handling code in the Mediatek CCI devfreq
driver, because the voltage of shared OPP might be changed by
multiple drivers (Mark Tseng, Dan Carpenter)
- Use device_get_match_data() in the Samsung Exynos PPMU
devfreq-event driver (Rob Herring)
- Extend support for the opp-level beyond required-opps (Ulf Hansson)
- Add dev_pm_opp_find_level_floor() (Krishna chaitanya chundru)
- dt-bindings: Allow opp-peak-kBpsfor kryo CPUs, support Qualcomm
Krait SoCs and document named opp-microvolt property (Bjorn
Andersson, Dmitry Baryshkov and Christian Marangi)
- Fix -Wunsequenced warning _of_add_opp_table_v1() (Nathan
Chancellor)
- General cleanup of OPP code (Viresh Kumar)
- Use __get_safe_page() rather than touching the list in hibernation
snapshot code (Brian Geffon)
- Fix symbol export for _SIMPLE_ variants of _PM_OPS() (Raag Jadav)
- Clean up sync_read handling in snapshot_write_next() (Brian Geffon)
- Fix kerneldoc comments for swsusp_check() and swsusp_close() to
better match code (Christoph Hellwig)
- Downgrade BIOS locked limits pr_warn() in the Intel RAPL power
capping driver to pr_debug() (Ville Syrjälä)
- Change the minimum python version for the intel_pstate_tracer
utility from 2.7 to 3.6 (Doug Smythies)"
* tag 'pm-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (82 commits)
dt-bindings: cpufreq: qcom-hw: document SM8650 CPUFREQ Hardware
cpufreq: arm: Kconfig: Add i.MX7 to supported SoC for ARM_IMX_CPUFREQ_DT
cpufreq: qcom-nvmem: add support for IPQ8064
cpufreq: qcom-nvmem: also accept operating-points-v2-krait-cpu
cpufreq: qcom-nvmem: drop pvs_ver for format a fuses
dt-bindings: cpufreq: qcom-cpufreq-nvmem: Document krait-cpu
cpufreq: qcom-nvmem: add support for IPQ6018
dt-bindings: cpufreq: qcom-cpufreq-nvmem: document IPQ6018
cpufreq: qcom-nvmem: Add MSM8909
cpufreq: qcom-nvmem: Simplify driver data allocation
powercap: intel_rapl: Downgrade BIOS locked limits pr_warn() to pr_debug()
cpufreq: stats: Fix buffer overflow detection in trans_stats()
dt-bindings: devfreq: event: rockchip,dfi: Add rk3588 support
dt-bindings: devfreq: event: rockchip,dfi: Add rk3568 support
dt-bindings: devfreq: event: convert Rockchip DFI binding to yaml
PM / devfreq: rockchip-dfi: add support for RK3588
PM / devfreq: rockchip-dfi: account for multiple DDRMON_CTRL registers
PM / devfreq: rockchip-dfi: make register stride SoC specific
PM / devfreq: rockchip-dfi: Add perf support
PM / devfreq: rockchip-dfi: give variable a better name
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These fix issues, add new quirks, rearrange the IRQ override quirk
definitions, add new helpers and switch over code to using them,
rework a couple of interfaces to be more flexible, eliminate strncpy()
usage from PNP, extend the ACPI PCC mailbox driver and clean up code.
This is based on ACPI thermal driver changes that are present in the
thermal control updates for 6.7-rc1 pull request (they are depended on
by the ACPI utilities updates). However, the ACPI thermal driver
changes are not included in the list of specific ACPI changes below.
Specifics:
- Add symbol definitions related to CDAT to the ACPICA code (Dave
Jiang)
- Use the acpi_device_is_present() helper in more places and rename
acpi_scan_device_not_present() to be about enumeration (James
Morse)
- Add __printf format attribute to acpi_os_vprintf() (Su Hui)
- Clean up departures from kernel coding style in the low-level
interface for ACPICA (Jonathan Bergh)
- Replace strncpy() with strscpy() in acpi_osi_setup() (Justin Stitt)
- Fail FPDT parsing on zero length records and add proper handling
for fpdt_process_subtable() to acpi_init_fpdt() (Vasily Khoruzhick)
- Rework acpi_handle_list handling so as to manage it dynamically,
including size computation (Rafael Wysocki)
- Clean up ACPI utilities code so as to make it follow the kernel
coding style (Jonathan Bergh)
- Consolidate IRQ trigger-type override DMI tables and drop .ident
values from dmi_system_id tables used for ACPI resources management
quirks (Hans de Goede)
- Add ACPI IRQ override for TongFang GMxXGxx (Werner Sembach)
- Allow _DSD buffer data only for byte accessors and document the
_DSD data buffer GUID (Andy Shevchenko)
- Drop BayTrail and Lynxpoint pinctrl device IDs from the ACPI LPSS
driver, because it does not need them (Raag Jadav)
- Add acpi_backlight=vendor quirk for Toshiba Portégé R100 (Ondrej
Zary)
- Add "vendor" backlight quirks for 3 Lenovo x86 Android tablets
(Hans de Goede)
- Move Xiaomi Mi Pad 2 backlight quirk to its own section (Hans de
Goede)
- Annotate struct prm_module_info with __counted_by (Kees Cook)
- Fix AER info corruption in aer_recover_queue() when error status
data has multiple sections (Shiju Jose)
- Make APEI use ERST maximum execution time for slow devices (Jeshua
Smith)
- Add support for platform notification handling to the PCC mailbox
driver and modify it to support shared interrupts for multiple
subspaces (Huisong Li)
- Define common macros to use when referring to various bitfields in
the PCC generic communications channel command and status fields
and use them in some drivers (Sudeep Holla)
- Add EC GPE detection quirk for HP 250 G7 Notebook PC (Jonathan
Denose)
- Fix and clean up create_pnp_modalias() and create_of_modalias()
(Christophe JAILLET)
- Modify 2 pieces of code to use acpi_evaluate_dsm_typed() (Andy
Shevchenko)
- Define acpi_dev_uid_match() for matching _UID and use it in several
places (Raag Jadav)
- Use acpi_device_uid() for fetching _UID in 2 places (Raag Jadav)
- Add context argument to acpi_dev_install_notify_handler() (Rafael
Wysocki)
- Clarify ACPI bus concepts in the ACPI device enumeration
documentation (Rafael Wysocki)
- Switch over the ACPI AC and ACPI PAD drivers to using the platform
driver interface which, is more logically consistent than binding a
driver directly to an ACPI device object, and clean them up (Michal
Wilczynski)
- Replace strncpy() in the PNP code with either memcpy() or strscpy()
as appropriate (Justin Stitt)
- Clean up coding style in pnp.h (GuoHua Cheng)"
* tag 'acpi-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (54 commits)
ACPI: resource: Do IRQ override on TongFang GMxXGxx
perf: arm_cspmu: use acpi_dev_hid_uid_match() for matching _HID and _UID
ACPI: EC: Add quirk for HP 250 G7 Notebook PC
ACPI: x86: use acpi_dev_uid_match() for matching _UID
ACPI: utils: use acpi_dev_uid_match() for matching _UID
pinctrl: intel: use acpi_dev_uid_match() for matching _UID
ACPI: utils: Introduce acpi_dev_uid_match() for matching _UID
ACPI: sysfs: Clean up create_pnp_modalias() and create_of_modalias()
ACPI: sysfs: Fix create_pnp_modalias() and create_of_modalias()
ACPI: acpi_pad: Rename ACPI device from device to adev
ACPI: acpi_pad: Use dev groups for sysfs
ACPI: acpi_pad: Replace acpi_driver with platform_driver
ACPI: APEI: Use ERST timeout for slow devices
ACPI: scan: Rename acpi_scan_device_not_present() to be about enumeration
PNP: replace deprecated strncpy() with memcpy()
PNP: ACPI: replace deprecated strncpy() with strscpy()
perf: qcom: use acpi_device_uid() for fetching _UID
ACPI: sysfs: use acpi_device_uid() for fetching _UID
ACPI: scan: Use the acpi_device_is_present() helper in more places
ACPI: AC: Rename ACPI device from device to adev
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These further rework the ACPI thermal driver, after the changes made
to it in the previous cycle, to make it easier to grasp, get rid of
redundant pieces of internal data structures and eliminate its
reliance on a specific ordering of trip point objects in the thermal
core, make thermal core adjustments needed for the ACPI thermal driver
rework, modify the thermal governor interface so as to use trip
pointers for representing trip points in it, switch over multiple
thermal drivers to using void platform driver remove callbacks, add
support for 2 hardware features to the Intel int340x thermal driver,
add support for new hardware on ARM platforms, update documentation,
fix problems, clean up code and update the MAINTAINERS record for
thermal control.
Specifics:
- Untangle the initialization and updates of passive and active trip
points in the ACPI thermal driver (Rafael Wysocki)
- Reduce code duplication related to the initialization and updates
of trip points in the ACPI thermal driver (Rafael Wysocki)
- Use trip pointers for cooling device binding in the ACPI thermal
driver (Rafael Wysocki)
- Simplify critical and hot trips representation in the ACPI thermal
driver (Rafael Wysocki)
- Use trip pointers in thermal governors and in the related part of
the thermal core (Rafael Wysocki)
- Drop the trips_disabled bitmask that has become redundant from the
thermal core (Rafael Wysocki)
- Avoid updating trip points when the thermal zone temperature falls
into a trip point's hysteresis range (ícolas F. R. A. Prado)
- Add power floor notifications support to the int340x thermal
control driver (Srinivas Pandruvada)
- Rework updating trip points in the int340x thermal driver so that
it does not access thermal zone internals directly (Rafael
Wysocki)
- Use param_get_byte() instead of param_get_int() as the max_idle
module parameter .get() callback in the Intel powerclamp thermal
driver to avoid possible out-of-bounds access (David Arcari)
- Add workload hints support to the int340x thermal driver (Srinivas
Pandruvada)
- Add support for Mediatek LVTS MT8192 along with suspend/resume
routines (Balsam Chihi)
- Fix probe for THERMAL_V2 in the Mediatek LVTS driver (Markus
Schneider-Pargmann)
- Remove duplicate error message from the max76620 driver when
thermal_of_zone_register() fails (Thierry Reding)
- Add i.MX7D compatible bindings to fix a warning from dtbs_check for
the imx6ul platform (Alexander Stein)
- Add sa8775p compatible to the QCom tsens driver (Priyansh Jain)
- Fix error check in lvts_debugfs_init() to be against PTR_ERR() in
the LVTS Mediatek driver (Minjie Du)
- Remove unused variable in thermal/tools (Kuan-Wei Chiu)
- Document the imx8dl thermal sensor (Fabio Estevam)
- Add variable names in callback prototypes to prevent warning from
checkpatch.pl in the imx8mm driver (Bragatheswaran Manickavel)
- Add missing unevaluatedProperties on child node schemas for
tegra124 (Rob Herring)
- Add mt7988 support to the Mediatek LVTS driver (Frank Wunderlich)"
* tag 'thermal-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (111 commits)
thermal: ACPI: Include the right header file
thermal: core: Don't update trip points inside the hysteresis range
thermal: core: Pass trip pointer to governor throttle callback
thermal: gov_step_wise: Fold update_passive_instance() into its caller
thermal: gov_power_allocator: Use trip pointers instead of trip indices
thermal: gov_fair_share: Rearrange get_trip_level()
thermal: trip: Define for_each_trip() macro
thermal: trip: Simplify computing trip indices
thermal/qcom/tsens: Drop ops_v0_1
thermal/drivers/mediatek/lvts_thermal: Update calibration data documentation
thermal/drivers/mediatek/lvts_thermal: Add mt8192 support
thermal/drivers/mediatek/lvts_thermal: Add suspend and resume
dt-bindings: thermal: mediatek: Add LVTS thermal controller definition for mt8192
thermal/drivers/mediatek: Fix probe for THERMAL_V2
thermal/drivers/max77620: Remove duplicate error message
dt-bindings: timer: add imx7d compatible
dt-bindings: net: microchip: Allow nvmem-cell usage
dt-bindings: imx-thermal: Add #thermal-sensor-cells property
dt-bindings: thermal: tsens: Add sa8775p compatible
thermal/drivers/mediatek/lvts_thermal: Fix error check in lvts_debugfs_init()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Support usec resolution of TCP timestamps, enabled selectively by a
route attribute.
- Defer regular TCP ACK while processing socket backlog, try to send
a cumulative ACK at the end. Increase single TCP flow performance
on a 200Gbit NIC by 20% (100Gbit -> 120Gbit).
- The Fair Queuing (FQ) packet scheduler:
- add built-in 3 band prio / WRR scheduling
- support bypass if the qdisc is mostly idle (5% speed up for TCP RR)
- improve inactive flow reporting
- optimize the layout of structures for better cache locality
- Support TCP Authentication Option (RFC 5925, TCP-AO), a more modern
replacement for the old MD5 option.
- Add more retransmission timeout (RTO) related statistics to
TCP_INFO.
- Support sending fragmented skbs over vsock sockets.
- Make sure we send SIGPIPE for vsock sockets if socket was
shutdown().
- Add sysctl for ignoring lower limit on lifetime in Router
Advertisement PIO, based on an in-progress IETF draft.
- Add sysctl to control activation of TCP ping-pong mode.
- Add sysctl to make connection timeout in MPTCP configurable.
- Support rcvlowat and notsent_lowat on MPTCP sockets, to help apps
limit the number of wakeups.
- Support netlink GET for MDB (multicast forwarding), allowing user
space to request a single MDB entry instead of dumping the entire
table.
- Support selective FDB flushing in the VXLAN tunnel driver.
- Allow limiting learned FDB entries in bridges, prevent OOM attacks.
- Allow controlling via configfs netconsole targets which were
created via the kernel cmdline at boot, rather than via configfs at
runtime.
- Support multiple PTP timestamp event queue readers with different
filters.
- MCTP over I3C.
BPF:
- Add new veth-like netdevice where BPF program defines the logic of
the xmit routine. It can operate in L3 and L2 mode.
- Support exceptions - allow asserting conditions which should never
be true but are hard for the verifier to infer. With some extra
flexibility around handling of the exit / failure:
https://lwn.net/Articles/938435/
- Add support for local per-cpu kptr, allow allocating and storing
per-cpu objects in maps. Access to those objects operates on the
value for the current CPU.
This allows to deprecate local one-off implementations of per-CPU
storage like BPF_MAP_TYPE_PERCPU_CGROUP_STORAGE maps.
- Extend cgroup BPF sockaddr hooks for UNIX sockets. The use case is
for systemd to re-implement the LogNamespace feature which allows
running multiple instances of systemd-journald to process the logs
of different services.
- Enable open-coded task_vma iteration, after maple tree conversion
made it hard to directly walk VMAs in tracing programs.
- Add open-coded task, css_task and css iterator support. One of the
use cases is customizable OOM victim selection via BPF.
- Allow source address selection with bpf_*_fib_lookup().
- Add ability to pin BPF timer to the current CPU.
- Prevent creation of infinite loops by combining tail calls and
fentry/fexit programs.
- Add missed stats for kprobes to retrieve the number of missed
kprobe executions and subsequent executions of BPF programs.
- Inherit system settings for CPU security mitigations.
- Add BPF v4 CPU instruction support for arm32 and s390x.
Changes to common code:
- overflow: add DEFINE_FLEX() for on-stack definition of structs with
flexible array members.
- Process doc update with more guidance for reviewers.
Driver API:
- Simplify locking in WiFi (cfg80211 and mac80211 layers), use wiphy
mutex in most places and remove a lot of smaller locks.
- Create a common DPLL configuration API. Allow configuring and
querying state of PLL circuits used for clock syntonization, in
network time distribution.
- Unify fragmented and full page allocation APIs in page pool code.
Let drivers be ignorant of PAGE_SIZE.
- Rework PHY state machine to avoid races with calls to phy_stop().
- Notify DSA drivers of MAC address changes on user ports, improve
correctness of offloads which depend on matching port MAC
addresses.
- Allow antenna control on injected WiFi frames.
- Reduce the number of variants of napi_schedule().
- Simplify error handling when composing devlink health messages.
Misc:
- A lot of KCSAN data race "fixes", from Eric.
- A lot of __counted_by() annotations, from Kees.
- A lot of strncpy -> strscpy and printf format fixes.
- Replace master/slave terminology with conduit/user in DSA drivers.
- Handful of KUnit tests for netdev and WiFi core.
Removed:
- AppleTalk COPS.
- AppleTalk ipddp.
- TI AR7 CPMAC Ethernet driver.
Drivers:
- Ethernet high-speed NICs:
- Intel (100G, ice, idpf):
- add a driver for the Intel E2000 IPUs
- make CRC/FCS stripping configurable
- cross-timestamping for E823 devices
- basic support for E830 devices
- use aux-bus for managing client drivers
- i40e: report firmware versions via devlink
- nVidia/Mellanox:
- support 4-port NICs
- increase max number of channels to 256
- optimize / parallelize SF creation flow
- Broadcom (bnxt):
- enhance NIC temperature reporting
- support PAM4 speeds and lane configuration
- Marvell OcteonTX2:
- PTP pulse-per-second output support
- enable hardware timestamping for VFs
- Solarflare/AMD:
- conntrack NAT offload and offload for tunnels
- Wangxun (ngbe/txgbe):
- expose HW statistics
- Pensando/AMD:
- support PCI level reset
- narrow down the condition under which skbs are linearized
- Netronome/Corigine (nfp):
- support CHACHA20-POLY1305 crypto in IPsec offload
- Ethernet NICs embedded, slower, virtual:
- Synopsys (stmmac):
- add Loongson-1 SoC support
- enable use of HW queues with no offload capabilities
- enable PPS input support on all 5 channels
- increase TX coalesce timer to 5ms
- RealTek USB (r8152): improve efficiency of Rx by using GRO frags
- xen: support SW packet timestamping
- add drivers for implementations based on TI's PRUSS (AM64x EVM)
- nVidia/Mellanox Ethernet datacenter switches:
- avoid poor HW resource use on Spectrum-4 by better block
selection for IPv6 multicast forwarding and ordering of blocks
in ACL region
- Ethernet embedded switches:
- Microchip:
- support configuring the drive strength for EMI compliance
- ksz9477: partial ACL support
- ksz9477: HSR offload
- ksz9477: Wake on LAN
- Realtek:
- rtl8366rb: respect device tree config of the CPU port
- Ethernet PHYs:
- support Broadcom BCM5221 PHYs
- TI dp83867: support hardware LED blinking
- CAN:
- add support for Linux-PHY based CAN transceivers
- at91_can: clean up and use rx-offload helpers
- WiFi:
- MediaTek (mt76):
- new sub-driver for mt7925 USB/PCIe devices
- HW wireless <> Ethernet bridging in MT7988 chips
- mt7603/mt7628 stability improvements
- Qualcomm (ath12k):
- WCN7850:
- enable 320 MHz channels in 6 GHz band
- hardware rfkill support
- enable IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS to
make scan faster
- read board data variant name from SMBIOS
- QCN9274: mesh support
- RealTek (rtw89):
- TDMA-based multi-channel concurrency (MCC)
- Silicon Labs (wfx):
- Remain-On-Channel (ROC) support
- Bluetooth:
- ISO: many improvements for broadcast support
- mark BCM4378/BCM4387 as BROKEN_LE_CODED
- add support for QCA2066
- btmtksdio: enable Bluetooth wakeup from suspend"
* tag 'net-next-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1816 commits)
net: pcs: xpcs: Add 2500BASE-X case in get state for XPCS drivers
net: bpf: Use sockopt_lock_sock() in ip_sock_set_tos()
net: mana: Use xdp_set_features_flag instead of direct assignment
vxlan: Cleanup IFLA_VXLAN_PORT_RANGE entry in vxlan_get_size()
iavf: delete the iavf client interface
iavf: add a common function for undoing the interrupt scheme
iavf: use unregister_netdev
iavf: rely on netdev's own registered state
iavf: fix the waiting time for initial reset
iavf: in iavf_down, don't queue watchdog_task if comms failed
iavf: simplify mutex_trylock+sleep loops
iavf: fix comments about old bit locks
doc/netlink: Update schema to support cmd-cnt-name and cmd-max-name
tools: ynl: introduce option to process unknown attributes or types
ipvlan: properly track tx_errors
netdevsim: Block until all devices are released
nfp: using napi_build_skb() to replace build_skb()
net: dsa: microchip: ksz9477: Fix spelling mistake "Enery" -> "Energy"
net: dsa: microchip: Ensure Stable PME Pin State for Wake-on-LAN
net: dsa: microchip: Refactor switch shutdown routine for WoL preparation
...
|
|
Add /proc/bootconfig description to Documentation/filesystems/proc.rst.
Link: https://lore.kernel.org/all/20231005171747.541123-3-paulmck@kernel.org/
Reported-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
- cpuset now supports remote partitions where CPUs can be reserved for
exclusive use down the tree without requiring all the intermediate
nodes to be partitions. This makes it easier to use partitions
without modifying existing cgroup hierarchy.
- cpuset partition configuration behavior improvement
- cgroup_favordynmods= boot param added to allow setting the flag on
boot on cgroup1
- Misc code and doc updates
* tag 'cgroup-for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
docs/cgroup: Add the list of threaded controllers to cgroup-v2.rst
cgroup: use legacy_name for cgroup v1 disable info
cgroup/cpuset: Cleanup signedness issue in cpu_exclusive_check()
cgroup/cpuset: Enable invalid to valid local partition transition
cgroup: add cgroup_favordynmods= command-line option
cgroup/cpuset: Extend test_cpuset_prs.sh to test remote partition
cgroup/cpuset: Documentation update for partition
cgroup/cpuset: Check partition conflict with housekeeping setup
cgroup/cpuset: Introduce remote partition
cgroup/cpuset: Add cpuset.cpus.exclusive for v2
cgroup/cpuset: Add cpuset.cpus.exclusive.effective for v2
cgroup/cpuset: Fix load balance state in update_partition_sd_lb()
cgroup: Avoid extra dereference in css_populate_dir()
cgroup: Check for ret during cgroup1_base_files cft addition
|
|
Pull rust updates from Miguel Ojeda:
"A small one compared to the previous one in terms of features. In
terms of lines, as usual, the 'alloc' version upgrade accounts for
most of them.
Toolchain and infrastructure:
- Upgrade to Rust 1.73.0
This time around, due to how the kernel and Rust schedules have
aligned, there are two upgrades in fact. They contain the fixes for
a few issues we reported to the Rust project.
In addition, a few cleanups indicated by the upgraded compiler or
possible thanks to it. For instance, the compiler now detects
redundant explicit links.
- A couple changes to the Rust 'Makefile' so that it can be used with
toybox tools, allowing Rust to be used in the Android kernel build.
x86:
- Enable IBT if enabled in C
Documentation:
- Add "The Rust experiment" section to the Rust index page
MAINTAINERS:
- Add Maintainer Entry Profile field ('P:').
- Update our 'W:' field to point to the webpage we have been building
this year"
* tag 'rust-6.7' of https://github.com/Rust-for-Linux/linux:
docs: rust: add "The Rust experiment" section
x86: Enable IBT in Rust if enabled in C
rust: Use grep -Ev rather than relying on GNU grep
rust: Use awk instead of recent xargs
rust: upgrade to Rust 1.73.0
rust: print: use explicit link in documentation
rust: task: remove redundant explicit link
rust: kernel: remove `#[allow(clippy::new_ret_no_self)]`
MAINTAINERS: add Maintainer Entry Profile field for Rust
MAINTAINERS: update Rust webpage
rust: upgrade to Rust 1.72.1
rust: arc: add explicit `drop()` around `Box::from_raw()`
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
- Check for out-of-memory condition during initialization (Jiasheng
Jiang)
- Fix documentation typos (Tudor Ambarus)
* tag 'pstore-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore/platform: Add check for kstrdup
docs: pstore-blk.rst: fix typo, s/console/ftrace
docs: pstore-blk.rst: use "about" as a preposition after "care"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks
Pull RCU updates from Frederic Weisbecker:
- RCU torture, locktorture and generic torture infrastructure updates
that include various fixes, cleanups and consolidations.
Among the user visible things, ftrace dumps can now be found into
their own file, and module parameters get better documented and
reported on dumps.
- Generic and misc fixes all over the place. Some highlights:
* Hotplug handling has seen some light cleanups and comments
* An RCU barrier can now be triggered through sysfs to serialize
memory stress testing and avoid OOM
* Object information is now dumped in case of invalid callback
invocation
* Also various SRCU issues, too hard to trigger to deserve urgent
pull requests, have been fixed
- RCU documentation updates
- RCU reference scalability test minor fixes and doc improvements.
- RCU tasks minor fixes
- Stall detection updates. Introduce RCU CPU Stall notifiers that
allows a subsystem to provide informations to help debugging. Also
cure some false positive stalls.
* tag 'rcu-next-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks: (56 commits)
srcu: Only accelerate on enqueue time
locktorture: Check the correct variable for allocation failure
srcu: Fix callbacks acceleration mishandling
rcu: Comment why callbacks migration can't wait for CPUHP_RCUTREE_PREP
rcu: Standardize explicit CPU-hotplug calls
rcu: Conditionally build CPU-hotplug teardown callbacks
rcu: Remove references to rcu_migrate_callbacks() from diagrams
rcu: Assume rcu_report_dead() is always called locally
rcu: Assume IRQS disabled from rcu_report_dead()
rcu: Use rcu_segcblist_segempty() instead of open coding it
rcu: kmemleak: Ignore kmemleak false positives when RCU-freeing objects
srcu: Fix srcu_struct node grpmask overflow on 64-bit systems
torture: Convert parse-console.sh to mktemp
rcutorture: Traverse possible cpu to set maxcpu in rcu_nocb_toggle()
rcutorture: Replace schedule_timeout*() 1-jiffy waits with HZ/20
torture: Add kvm.sh --debug-info argument
locktorture: Rename readers_bind/writers_bind to bind_readers/bind_writers
doc: Catch-up update for locktorture module parameters
locktorture: Add call_rcu_chains module parameter
locktorture: Add new module parameters to lock_torture_print_module_parms()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu
Pull CSD lock update from Paul McKenney:
"This adds a kernel boot parameter that causes the kernel to panic if
one of the call_smp_function() APIs is stalled for more than the
specified duration.
This is useful in deployments in which a clean panic is preferable to
an indefinite stall"
* tag 'csd-lock.2023.10.23a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
smp,csd: Throw an error if a CSD lock is stuck for too long
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu
Pull Linux Kernel Memory Model updates from Paul McKenney:
"This update adds paragraphs to the portions of memory-barriers.txt
that have been marked historical due to changes in the way that the
Linux kernel handles DEC Alpha. These paragraphs includes information
on where to find the corresponding up-to-date information"
* tag 'lkmm.2023.10.28a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
docs: memory-barriers: Add note on compiler transformation and address deps
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 core updates from Thomas Gleixner:
- Limit the hardcoded topology quirk for Hygon CPUs to those which have
a model ID less than 4.
The newer models have the topology CPUID leaf 0xB correctly
implemented and are not affected.
- Make SMT control more robust against enumeration failures
SMT control was added to allow controlling SMT at boottime or
runtime. The primary purpose was to provide a simple mechanism to
disable SMT in the light of speculation attack vectors.
It turned out that the code is sensible to enumeration failures and
worked only by chance for XEN/PV. XEN/PV has no real APIC enumeration
which means the primary thread mask is not set up correctly. By
chance a XEN/PV boot ends up with smp_num_siblings == 2, which makes
the hotplug control stay at its default value "enabled". So the mask
is never evaluated.
The ongoing rework of the topology evaluation caused XEN/PV to end up
with smp_num_siblings == 1, which sets the SMT control to "not
supported" and the empty primary thread mask causes the hotplug core
to deny the bringup of the APS.
Make the decision logic more robust and take 'not supported' and 'not
implemented' into account for the decision whether a CPU should be
booted or not.
- Fake primary thread mask for XEN/PV
Pretend that all XEN/PV vCPUs are primary threads, which makes the
usage of the primary thread mask valid on XEN/PV. That is consistent
with because all of the topology information on XEN/PV is fake or
even non-existent.
- Encapsulate topology information in cpuinfo_x86
Move the randomly scattered topology data into a separate data
structure for readability and as a preparatory step for the topology
evaluation overhaul.
- Consolidate APIC ID data type to u32
It's fixed width hardware data and not randomly u16, int, unsigned
long or whatever developers decided to use.
- Cure the abuse of cpuinfo for persisting logical IDs.
Per CPU cpuinfo is used to persist the logical package and die IDs.
That's really not the right place simply because cpuinfo is subject
to be reinitialized when a CPU goes through an offline/online cycle.
Use separate per CPU data for the persisting to enable the further
topology management rework. It will be removed once the new topology
management is in place.
- Provide a debug interface for inspecting topology information
Useful in general and extremly helpful for validating the topology
management rework in terms of correctness or "bug" compatibility.
* tag 'x86-core-2023-10-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/apic, x86/hyperv: Use u32 in hv_snp_boot_ap() too
x86/cpu: Provide debug interface
x86/cpu/topology: Cure the abuse of cpuinfo for persisting logical ids
x86/apic: Use u32 for wakeup_secondary_cpu[_64]()
x86/apic: Use u32 for [gs]et_apic_id()
x86/apic: Use u32 for phys_pkg_id()
x86/apic: Use u32 for cpu_present_to_apicid()
x86/apic: Use u32 for check_apicid_used()
x86/apic: Use u32 for APIC IDs in global data
x86/apic: Use BAD_APICID consistently
x86/cpu: Move cpu_l[l2]c_id into topology info
x86/cpu: Move logical package and die IDs into topology info
x86/cpu: Remove pointless evaluation of x86_coreid_bits
x86/cpu: Move cu_id into topology info
x86/cpu: Move cpu_core_id into topology info
hwmon: (fam15h_power) Use topology_core_id()
scsi: lpfc: Use topology_core_id()
x86/cpu: Move cpu_die_id into topology info
x86/cpu: Move phys_proc_id into topology info
x86/cpu: Encapsulate topology information in cpuinfo_x86
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Updates for time, timekeeping and timers:
Core:
- Avoid superfluous deactivation of the tick in the low resolution
tick NOHZ interrupt handler as the deactivation is handled already
in the idle loop and on interrupt exit.
- Update stale comments in the tick NOHZ code and rename the tick
handler functions to be self-explanatory.
- Remove an unused function in the tick NOHZ code, which was
forgotten when the last user went away.
- Handle RTC alarms which exceed the maximum alarm time of the
underlying RTC hardware gracefully.
Setting RTC alarms which exceed the maximum alarm time of the RTC
hardware failed so far and caused suspend operations to abort.
Cure this by limiting the alarm to the maximum alarm time of the
RTC hardware, which is provided by the driver. This causes early
resume wakeups, but that's way better than not suspending at all.
Drivers:
- Add a proper clocksource/event driver for the ancient Cirrus Logic
EP93xx SoC family, which is one of the last non device-tree
holdouts in arch/arm.
- The usual boring device tree bindings updates and small fixes and
enhancements all over the place"
* tag 'timers-core-2023-10-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: ep93xx: Add driver for Cirrus Logic EP93xx
dt-bindings: timers: Add Cirrus EP93xx
clocksource/drivers/timer-atmel-tcb: Fix initialization on SAM9 hardware
clocksource/timer-riscv: ACPI: Add timer_cannot_wakeup_cpu
clocksource/drivers/sun5i: Remove surplus dev_err() when using platform_get_irq()
drivers/clocksource/timer-ti-dm: Don't call clk_get_rate() in stop function
clocksource/drivers/timer-imx-gpt: Fix potential memory leak
dt-bindings: timer: renesas,rz-mtu3: Document RZ/{G2UL,Five} SoCs
dt-bindings: timer: renesas,rz-mtu3: Improve documentation
dt-bindings: timer: renesas,rz-mtu3: Fix overflow/underflow interrupt names
alarmtimer: Use maximum alarm time for suspend
rtc: Add API function to return alarm time bound by hardware limit
tick/nohz: Update comments some more
tick/nohz: Remove unused tick_nohz_idle_stop_tick_protected()
tick/nohz: Don't shutdown the lowres tick from itself
tick/nohz: Update obsolete comments
tick/nohz: Rename the tick handlers to more self-explanatory names
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm handling updates from Ingo Molnar:
- Add new NX-stack self-test
- Improve NUMA partial-CFMWS handling
- Fix #VC handler bugs resulting in SEV-SNP boot failures
- Drop the 4MB memory size restriction on minimal NUMA nodes
- Reorganize headers a bit, in preparation to header dependency
reduction efforts
- Misc cleanups & fixes
* tag 'x86-mm-2023-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Drop the 4 MB restriction on minimal NUMA node memory size
selftests/x86/lam: Zero out buffer for readlink()
x86/sev: Drop unneeded #include
x86/sev: Move sev_setup_arch() to mem_encrypt.c
x86/tdx: Replace deprecated strncpy() with strtomem_pad()
selftests/x86/mm: Add new test that userspace stack is in fact NX
x86/sev: Make boot_ghcb_page[] static
x86/boot: Move x86_cache_alignment initialization to correct spot
x86/sev-es: Set x86_virt_bits to the correct value straight away, instead of a two-phase approach
x86/sev-es: Allow copy_from_kernel_nofault() in earlier boot
x86_64: Show CR4.PSE on auxiliaries like on BSP
x86/iommu/docs: Update AMD IOMMU specification document URL
x86/sev/docs: Update document URL in amd-memory-encryption.rst
x86/mm: Move arch_memory_failure() and arch_is_platform_page() definitions from <asm/processor.h> to <asm/pgtable.h>
ACPI/NUMA: Apply SRAT proximity domain to entire CFMWS window
x86/numa: Introduce numa_fill_memblks()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 entry updates from Ingo Molnar:
- Make IA32_EMULATION boot time configurable with
the new ia32_emulation=<bool> boot option
- Clean up fast syscall return validation code: convert
it to C and refactor the code
- As part of this, optimize the canonical RIP test code
* tag 'x86-entry-2023-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/32: Clean up syscall fast exit tests
x86/entry/64: Use TASK_SIZE_MAX for canonical RIP test
x86/entry/64: Convert SYSRET validation tests to C
x86/entry/32: Remove SEP test for SYSEXIT
x86/entry/32: Convert do_fast_syscall_32() to bool return type
x86/entry/compat: Combine return value test from syscall handler
x86/entry/64: Remove obsolete comment on tracing vs. SYSRET
x86: Make IA32_EMULATION boot time configurable
x86/entry: Make IA32 syscalls' availability depend on ia32_enabled()
x86/elf: Make loading of 32bit processes depend on ia32_enabled()
x86/entry: Compile entry_SYSCALL32_ignore() unconditionally
x86/entry: Rename ignore_sysret()
x86: Introduce ia32_enabled()
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.7-rc1:
drm-misc-next-2023-10-19 + following:
UAPI Changes:
Cross-subsystem Changes:
- Convert fbdev drivers to use fbdev i/o mem helpers.
Core Changes:
- Use cross-references for macros in docs.
- Make drm_client_buffer_addb use addfb2.
- Add NV20 and NV30 YUV formats.
- Documentation updates for create_dumb ioctl.
- CI fixes.
- Allow variable number of run-queues in scheduler.
Driver Changes:
- Rename drm/ast constants.
- Make ili9882t its own driver.
- Assorted fixes in ivpu, vc4, bridge/synopsis, amdgpu.
- Add planar formats to rockchip.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3d92fae8-9b1b-4165-9ca8-5fda11ee146b@linux.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"Fair scheduler (SCHED_OTHER) improvements:
- Remove the old and now unused SIS_PROP code & option
- Scan cluster before LLC in the wake-up path
- Use candidate prev/recent_used CPU if scanning failed for cluster
wakeup
NUMA scheduling improvements:
- Improve the VMA access-PID code to better skip/scan VMAs
- Extend tracing to cover VMA-skipping decisions
- Improve/fix the recently introduced sched_numa_find_nth_cpu() code
- Generalize numa_map_to_online_node()
Energy scheduling improvements:
- Remove the EM_MAX_COMPLEXITY limit
- Add tracepoints to track energy computation
- Make the behavior of the 'sched_energy_aware' sysctl more
consistent
- Consolidate and clean up access to a CPU's max compute capacity
- Fix uclamp code corner cases
RT scheduling improvements:
- Drive dl_rq->overloaded with dl_rq->pushable_dl_tasks updates
- Drive the ->rto_mask with rt_rq->pushable_tasks updates
Scheduler scalability improvements:
- Rate-limit updates to tg->load_avg
- On x86 disable IBRS when CPU is offline to improve single-threaded
performance
- Micro-optimize in_task() and in_interrupt()
- Micro-optimize the PSI code
- Avoid updating PSI triggers and ->rtpoll_total when there are no
state changes
Core scheduler infrastructure improvements:
- Use saved_state to reduce some spurious freezer wakeups
- Bring in a handful of fast-headers improvements to scheduler
headers
- Make the scheduler UAPI headers more widely usable by user-space
- Simplify the control flow of scheduler syscalls by using lock
guards
- Fix sched_setaffinity() vs. CPU hotplug race
Scheduler debuggability improvements:
- Disallow writing invalid values to sched_rt_period_us
- Fix a race in the rq-clock debugging code triggering warnings
- Fix a warning in the bandwidth distribution code
- Micro-optimize in_atomic_preempt_off() checks
- Enforce that the tasklist_lock is held in for_each_thread()
- Print the TGID in sched_show_task()
- Remove the /proc/sys/kernel/sched_child_runs_first sysctl
... and misc cleanups & fixes"
* tag 'sched-core-2023-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (82 commits)
sched/fair: Remove SIS_PROP
sched/fair: Use candidate prev/recent_used CPU if scanning failed for cluster wakeup
sched/fair: Scan cluster before scanning LLC in wake-up path
sched: Add cpus_share_resources API
sched/core: Fix RQCF_ACT_SKIP leak
sched/fair: Remove unused 'curr' argument from pick_next_entity()
sched/nohz: Update comments about NEWILB_KICK
sched/fair: Remove duplicate #include
sched/psi: Update poll => rtpoll in relevant comments
sched: Make PELT acronym definition searchable
sched: Fix stop_one_cpu_nowait() vs hotplug
sched/psi: Bail out early from irq time accounting
sched/topology: Rename 'DIE' domain to 'PKG'
sched/psi: Delete the 'update_total' function parameter from update_triggers()
sched/psi: Avoid updating PSI triggers and ->rtpoll_total when there are no state changes
sched/headers: Remove comment referring to rq::cpu_load, since this has been removed
sched/numa: Complete scanning of inactive VMAs when there is no alternative
sched/numa: Complete scanning of partial VMAs regardless of PID activity
sched/numa: Move up the access pid reset logic
sched/numa: Trace decisions related to skipping VMAs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 resource control updates from Borislav Petkov:
- Add support for non-contiguous capacity bitmasks being added to
Intel's CAT implementation
- Other improvements to resctrl code: better configuration,
simplifications, debugging support, fixes
* tag 'x86_cache_for_6.7_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/resctrl: Display RMID of resource group
x86/resctrl: Add support for the files of MON groups only
x86/resctrl: Display CLOSID for resource group
x86/resctrl: Introduce "-o debug" mount option
x86/resctrl: Move default group file creation to mount
x86/resctrl: Unwind properly from rdt_enable_ctx()
x86/resctrl: Rename rftype flags for consistency
x86/resctrl: Simplify rftype flag definitions
x86/resctrl: Add multiple tasks to the resctrl group at once
Documentation/x86: Document resctrl's new sparse_masks
x86/resctrl: Add sparse_masks file in info
x86/resctrl: Enable non-contiguous CBMs in Intel CAT
x86/resctrl: Rename arch_has_sparse_bitmaps
x86/resctrl: Fix remaining kernel-doc warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 hw mitigation updates from Borislav Petkov:
- A bunch of improvements, cleanups and fixlets to the SRSO mitigation
machinery and other, general cleanups to the hw mitigations code, by
Josh Poimboeuf
- Improve the return thunk detection by objtool as it is absolutely
important that the default return thunk is not used after returns
have been patched. Future work to detect and report this better is
pending
- Other misc cleanups and fixes
* tag 'x86_bugs_for_6.7_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86/retpoline: Document some thunk handling aspects
x86/retpoline: Make sure there are no unconverted return thunks due to KCSAN
x86/callthunks: Delete unused "struct thunk_desc"
x86/vdso: Run objtool on vdso32-setup.o
objtool: Fix return thunk patching in retpolines
x86/srso: Remove unnecessary semicolon
x86/pti: Fix kernel warnings for pti= and nopti cmdline options
x86/calldepth: Rename __x86_return_skl() to call_depth_return_thunk()
x86/nospec: Refactor UNTRAIN_RET[_*]
x86/rethunk: Use SYM_CODE_START[_LOCAL]_NOALIGN macros
x86/srso: Disentangle rethunk-dependent options
x86/srso: Move retbleed IBPB check into existing 'has_microcode' code block
x86/bugs: Remove default case for fully switched enums
x86/srso: Remove 'pred_cmd' label
x86/srso: Unexport untraining functions
x86/srso: Improve i-cache locality for alias mitigation
x86/srso: Fix unret validation dependencies
x86/srso: Fix vulnerability reporting for missing microcode
x86/srso: Print mitigation for retbleed IBPB case
x86/srso: Print actual mitigation if requested mitigation isn't possible
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Borislav Petkov:
- A new EDAC driver for Xilinx's Versal integrated memory controller
* tag 'edac_updates_for_v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/versal: Add a Xilinx Versal memory controller driver
dt-bindings: memory-controllers: Add support for Xilinx Versal EDAC for DDRMC
|
|
The QMC (QUICC mutichannel controller) is a controller present in some
PowerQUICC SoC such as MPC885.
The QMC HDLC uses the QMC controller to transfer HDLC data.
Additionally, a framer can be connected to the QMC HDLC.
If present, this framer is the interface between the TDM bus used by the
QMC HDLC and the E1/T1 line.
The QMC HDLC can use this framer to get information about the E1/T1 line
and configure the E1/T1 line.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231011061437.64213-9-herve.codina@bootlin.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
false' in child nodes
Additional properties in child node should not be allowed.
Prevent them adding 'additionalProperties: false'
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231011061437.64213-8-herve.codina@bootlin.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The given example mentions the 'fsl,mode' property whereas the
correct property name, the one described, is 'fsl,operational-mode'.
Fix the example to use the correct property name.
Fixes: a9b121327c93 ("dt-bindings: soc: fsl: cpm_qe: Add QMC controller")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231011061437.64213-7-herve.codina@bootlin.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
'clk-frac-divider' into clk-next
- Make clk kunit tests work with lockdep
- Fix clk gate kunit test for big-endian
- Convert more than a handful of clk drivers to use regmap maple tree
- Consider the CLK_FRAC_DIVIDER_ZERO_BASED in fractional divider clk
implementation
* clk-renesas: (23 commits)
clk: renesas: r9a08g045: Add clock and reset support for SDHI1 and SDHI2
clk: renesas: rzg2l: Use %x format specifier to print CLK_ON_R()
clk: renesas: Add minimal boot support for RZ/G3S SoC
clk: renesas: rzg2l: Add divider clock for RZ/G3S
clk: renesas: rzg2l: Refactor SD mux driver
clk: renesas: rzg2l: Remove CPG_SDHI_DSEL from generic header
clk: renesas: rzg2l: Add struct clk_hw_data
clk: renesas: rzg2l: Add support for RZ/G3S PLL
clk: renesas: rzg2l: Remove critical area
clk: renesas: rzg2l: Fix computation formula
clk: renesas: rzg2l: Trust value returned by hardware
clk: renesas: rzg2l: Lock around writes to mux register
clk: renesas: rzg2l: Wait for status bit of SD mux before continuing
clk: renesas: rcar-gen3: Extend SDnH divider table
dt-bindings: clock: renesas,rzg2l-cpg: Document RZ/G3S SoC
clk: renesas: r8a7795: Constify r8a7795_*_clks
clk: renesas: r9a06g032: Name anonymous structs
clk: renesas: r9a06g032: Fix kerneldoc warning
clk: renesas: rzg2l: Use u32 for flag and mux_flags
clk: renesas: rzg2l: Use FIELD_GET() for PLL register fields
...
* clk-kunit:
clk: Fix clk gate kunit test on big-endian CPUs
clk: Parameterize clk_leaf_mux_set_rate_parent
clk: Drive clk_leaf_mux_set_rate_parent test from clk_ops
* clk-regmap:
clk: versaclock7: Convert to use maple tree register cache
clk: versaclock5: Convert to use maple tree register cache
clk: versaclock3: Convert to use maple tree register cache
clk: versaclock3: Remove redundant _is_writeable()
clk: si570: Convert to use maple tree register cache
clk: si544: Convert to use maple tree register cache
clk: si5351: Convert to use maple tree register cache
clk: si5341: Convert to use maple tree register cache
clk: si514: Convert to use maple tree register cache
clk: cdce925: Convert to use maple tree register cache
* clk-frac-divider:
clk: fractional-divider: tests: Add test suite for edge cases
clk: fractional-divider: Improve approximation when zero based and export
|
|
and 'clk-qcom' into clk-next
- Add consumer info to clk debugfs
- Fix various clk drivers that have clk_hw_onecell_data not at the end
of an allocation
* clk-debugfs:
clk: Allow phase adjustment from debugfs
clk: Show active consumers of clocks in debugfs
* clk-spreadtrum:
clk: sprd: Composite driver support offset config
* clk-sifive:
clk: sifive: Allow building the driver as a module
clk: analogbits: Allow building the library as a module
* clk-counted:
clk: socfpga: agilex: Add bounds-checking coverage for struct stratix10_clock_data
clk: socfpga: Fix undefined behavior bug in struct stratix10_clock_data
clk: visconti: Add bounds-checking coverage for struct visconti_pll_provider
clk: visconti: Fix undefined behavior bug in struct visconti_pll_provider
* clk-qcom: (36 commits)
clk: qcom: apss-ipq6018: add the GPLL0 clock also as clock provider
clk: qcom: ipq5332: drop the CLK_SET_RATE_PARENT flag from GPLL clocks
clk: qcom: ipq9574: drop the CLK_SET_RATE_PARENT flag from GPLL clocks
clk: qcom: ipq5018: drop the CLK_SET_RATE_PARENT flag from GPLL clocks
clk: qcom: ipq6018: drop the CLK_SET_RATE_PARENT flag from PLL clocks
clk: qcom: ipq8074: drop the CLK_SET_RATE_PARENT flag from PLL clocks
clk: qcom: gcc-ipq6018: add QUP6 I2C clock
clk: qcom: apss-ipq6018: ipq5332: add safe source switch for a53pll
clk: qcom: apss-ipq-pll: Fix 'l' value for ipq5332_pll_config
clk: qcom: apss-ipq-pll: Use stromer plus ops for stromer plus pll
clk: qcom: clk-alpha-pll: introduce stromer plus ops
clk: qcom: config IPQ_APSS_6018 should depend on QCOM_SMEM
clk: qcom: videocc-sm8550: switch to clk_lucid_ole_pll_configure
clk: qcom: gpucc-sm8550: switch to clk_lucid_ole_pll_configure
clk: qcom: Replace of_device.h with explicit includes
clk: qcom: smd-rpm: Move CPUSS_GNoC clock to interconnect
clk: qcom: cbf-msm8996: Convert to platform remove callback returning void
clk: qcom: gcc-sm8150: Fix gcc_sdcc2_apps_clk_src
clk: qcom: Add GCC driver support for SM4450
dt-bindings: clock: qcom: Add GCC clocks for SM4450
...
|
|
'clk-imx' into clk-next
- Add clock driver for TWL6032
* clk-doc:
clk: linux/clk-provider.h: fix kernel-doc warnings and typos
* clk-amlogic:
clk: meson: S4: select CONFIG_COMMON_CLK_MESON_CLKC_UTILS
clk: meson: S4: add support for Amlogic S4 SoC peripheral clock controller
clk: meson: S4: add support for Amlogic S4 SoC PLL clock driver
dt-bindings: clock: document Amlogic S4 SoC peripherals clock controller
dt-bindings: clock: document Amlogic S4 SoC PLL clock controller
* clk-mediatek:
clk: mediatek: fix double free in mtk_clk_register_pllfh()
clk: mediatek: clk-mt2701: Add check for mtk_alloc_clk_data
clk: mediatek: clk-mt7629: Add check for mtk_alloc_clk_data
clk: mediatek: clk-mt7629-eth: Add check for mtk_alloc_clk_data
clk: mediatek: clk-mt6797: Add check for mtk_alloc_clk_data
clk: mediatek: clk-mt6779: Add check for mtk_alloc_clk_data
clk: mediatek: clk-mt6765: Add check for mtk_alloc_clk_data
* clk-twl:
clk: twl: add clock driver for TWL6032
* clk-imx:
clk: imx: imx8qm/qxp: add more resources to whitelist
clk: imx: scu: ignore clks not owned by Cortex-A partition
clk: imx8: remove MLB support
clk: imx: imx8qm-rsrc: drop VPU_UART/VPUCORE
clk: imx: imx8qxp: correct the enet clocks for i.MX8DXL
clk: imx: imx8qxp: Fix elcdif_pll clock
clk: imx: imx8dxl-rsrc: keep sorted in the ascending order
clk: imx: imx6sx: Allow a different LCDIF1 clock parent
clk: imx: imx8mq: correct error handling path
clk: imx8mp: Remove non-existent IMX8MP_CLK_AUDIOMIX_PDM_ROOT
clk: imx: imx8: Simplify clk_imx_acm_detach_pm_domains()
clk: imx: imx8: Add a message in case of devm_clk_hw_register_mux_parent_data_table() error
clk: imx: imx8: Fix an error handling path in imx8_acm_clk_probe()
clk: imx: imx8: Fix an error handling path if devm_clk_hw_register_mux_parent_data_table() fails
clk: imx: imx8: Fix an error handling path in clk_imx_acm_attach_pm_domains()
clk: imx: Select MXC_CLK for CLK_IMX8QXP
|
|
Just as unevaluatedProperties or additionalProperties are required at
the top level of schemas, they should (and will) also be required for
child node schemas. That ensures only documented properties are
present for any node.
Adding additionalProperties constraint on 'trig-conns' nodes results in
warnings that 'cpu' and 'arm,cs-dev-assoc' are not allowed. These are
already defined for the parent node, but need to be duplicated for the
child node. Drop the free form description that the properties also apply
to the child nodes.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Link: https://lore.kernel.org/r/20230925220511.2026514-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
'cpu' has been added as a single phandle type to dtschema, so drop the
type here.
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230925220511.2026514-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The soundwire-controller.yaml schema already defines the form for devices
in child nodes, so there's no need to do the same in the QCom controller
binding. Add a $ref to the soundwire-controller.yaml schema and drop the
child node schema.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231016155537.2973625-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
