Age | Commit message (Collapse) | Author | Files | Lines |
|
vs. fixed 512M before.
But this still assumes that all of memory is under IOC which may not be
true for the SoC. Improve that later when this becomes a real issue, by
specifying this from DT.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
On AXS103 release bitfiles, DMA data corruptions were seen because IOC
setup was not following the recommended way in documentation.
Flipping IOC on when caches are enabled or coherency transactions are in
flight, might cause some of the memory operations to not observe
coherency as expected.
So strictly follow the programming model recommendations as documented
in comment header above arc_ioc_setup()
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
- Move IOC setup into arc_ioc_setup()
- Move SLC disabling into arc_slc_disable()
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
commit d65283f7b695b5 added mod->arch.secstr under
CONFIG_ARC_DW2_UNWIND, but used it unconditionally which broke builds
when the option was disabled. Fix that by adjusting the #ifdef guard.
And while at it add a missing guard (for unwinder) in module.c as well
Reported-by: Waldemar Brodkorb <wbx@openadk.org>
Cc: stable@vger.kernel.org #4.9
Fixes: d65283f7b695b5 ("ARC: module: elide loop to save reference to .eh_frame")
Tested-by: Anton Kolesov <akolesov@synopsys.com>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
[abrodkin: provided fixlet to Kconfig per failure in allnoconfig build]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
This is not exposed to userspace debugers yet, which can be done
independently as a seperate patch !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull more ARC updates from Vineet Gupta:
- Fix for aliasing VIPT dcache in old ARC700 cores
- micro-optimization in ARC700 ProtV handler
- Enable SG_CHAIN [Vladimir]
- ARC HS38 core intc default to prio 1
* tag 'arc-4.10-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: arc700: Don't assume 2 colours for aliasing VIPT dcache
ARC: mm: No need to save cache version in @cpuinfo
ARC: enable SG chaining
ARCv2: intc: default all interrupts to priority 1
ARCv2: entry: document intr disable in hard isr
ARC: ARCompact entry: elide re-reading ECR in ProtV handler
|
|
An ARC700 customer reported linux boot crashes when upgrading to bigger
L1 dcache (64K from 32K). Turns out they had an aliasing VIPT config and
current code only assumed 2 colours, while theirs had 4. So default to 4
colours and complain if there are fewer. Ideally this needs to be a
Kconfig option, but heck that's too much of hassle for a single user.
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Historical MMU revisions have been paired with Cache revision updates
which are captured in MMU and Cache Build Configuration Registers respectively.
This was used in boot code to check for configurations mismatches,
speically in simulations (such as running with non existent caches,
non pairing MMU and Cache version etc). This can instead be inferred
from other cache params such as line size. So remove @ver from post
processed @cpuinfo which could be used later to save soem other
interesting info.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"These are mostly timer/clocksource driver updates which were
Reviewed/Acked by Daniel but had to be merged via ARC tree due to
dependencies.
I will follow up with another pull request with actual ARC changes
early next week !
Summary:
- Moving ARC timer driver into drivers/clocksource
- EZChip timer driver updates [Noam]
- ARC AXS103 and HAPS platform updates [Alexey]"
* tag 'arc-4.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: axs10x: really enable ARC PGU
ARC: rename Zebu platform support to HAPS
clocksource: nps: avoid maybe-uninitialized warning
clocksource: Add clockevent support to NPS400 driver
clocksource: update "fn" at CLOCKSOURCE_OF_DECLARE() of nps400 timer
soc: Support for NPS HW scheduling
clocksource: import ARC timer driver
ARC: breakout timer include code into separate header ...
ARC: move mcip.h into include/soc and adjust the includes
ARC: breakout aux handling into a separate header
ARC: time: move time_init() out of the driver
ARC: timer: gfrc, rtc: build under same option (64-bit timers)
ARC: timer: gfrc, rtc: Read BCR to detect whether hardware exists ...
ARC: timer: gfrc, rtc: deuglify big endian code
|
|
ARC HS Cores support configurable multiple interrupt priorities of upto
16 levels. In commit dec2b2849cfcc ("ARCv2: intc: Allow interruption by
lowest priority interrupt") we switched to 15 which seems a bit
excessive given that there would be rare hardware implementing so many
preemption levels AND running Linux. It would seem that 2 levels will be
more common so switch to 1 as the default priority level. This will be
the "lower" priority level saving 0 for implementing NMI style support.
This scheme also works in systems with more than 2 prioity levels as
well.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
... which allows for use in drivers/clocksource later
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Also remove the dependency on ARCv2, to increase compile coverage for
!ARCV2 builds
Acked-by: Daniel Lezcano <daniel.lezcnao@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
ARC timers use aux registers for programming and this paves way for
moving ARC timer drivers into drivers/clocksource
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
commit 1c3c90930392 broke PAE40. Macro pfn_pte(pfn, prot) creates paddr
from pfn, but the page shift was getting truncated to 32 bits since we lost
the proper cast to 64 bits (for PAE400
Instead of reverting that commit, use a better helper which is 32/64 bits
safe just like ARM implementation.
Fixes: 1c3c90930392 ("ARC: mm: fix build breakage with STRICT_MM_TYPECHECKS")
Cc: <stable@vger.kernel.org> #4.4+
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
[vgupta: massaged changelog]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Apparenty this is coming in the way of gcc fix which inhibits the usage
of LP_COUNT as a gpr.
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
No need to duplicate the same define everywhere. Since
the only user is stop-machine and the only provider is
s390, we can use a default implementation of cpu_relax_yield()
in sched.h.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvm@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-s390 <linux-s390@vger.kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1479298985-191589-1-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
As there are no users left, we can remove cpu_relax_lowlatency()
implementations from every architecture.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Cc: <linux-arch@vger.kernel.org>
Link: http://lkml.kernel.org/r/1477386195-32736-6-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
For spinning loops people do often use barrier() or cpu_relax().
For most architectures cpu_relax and barrier are the same, but on
some architectures cpu_relax can add some latency.
For example on power,sparc64 and arc, cpu_relax can shift the CPU
towards other hardware threads in an SMT environment.
On s390 cpu_relax does even more, it uses an hypercall to the
hypervisor to give up the timeslice.
In contrast to the SMT yielding this can result in larger latencies.
In some places this latency is unwanted, so another variant
"cpu_relax_lowlatency" was introduced. Before this is used in more
and more places, lets revert the logic and provide a cpu_relax_yield
that can be called in places where yielding is more important than
latency. By default this is the same as cpu_relax on all architectures.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1477386195-32736-2-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This came up when reviewing code to address missing IRQ affinity
setting in AXS103 platform and/or implementing hierarchical IRQ domains
- smp_ipi_irq_setup() callers pass hwirq but in turn calls
request_percpu_irq() which expects a linux virq. So invoke
irq_find_mapping() to do the conversion
(also explicitify this in code by renaming the args appropriately)
- idu_of_init()/idu_cascade_isr() were similarly using linux virq where
hwirq is expected, so do the conversion using irqd_to_hwirq() helper
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
[vgupta: made changelog a bit concise a bit]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
The original syscall only used to return errno to indicate if cmpxchg
succeeded. It was not returning the "previous" value which typical cmpxchg
callers are interested in to build their slowpaths or retry loops.
Given user preemption in syscall return path etc, it is not wise to
check this in userspace afterwards, but should be what kernel actually
observed in the syscall.
So change the syscall interface to always return the previous value and
additionally set Z flag to indicate whether operation succeeded or not
(just like ARM implementation when they used to have this syscall)
The flag approach avoids having to put_user errno which is nice given
the use case for this syscall cares mostly about the "previous" value.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
The loop was really needed in .debug_frame regime where wanted make it
as SH_ALLOC so that apply_relocate_add() would process it. That's not
needed for .eh_frame, so we check this in apply_relocate_add() which
gets called for each section.
Note that we need to save reference to "section name strings" section in
module_frob_arch_sections() since apply_relocate_add() doesn't get that
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
The motivation is to identify ARC750 vs. ARC770 (we currently print
generic "ARC700").
A given ARC700 release could be 750 or 770, with same ARCNUM (or family
identifier which is unfortunate). The existing arc_cpu_tbl[] kept a single
concatenated string for core name and release which thus doesn't work
for 750 vs. 770 identification.
So split this into 2 tables, one with core names and other with release.
And while we are at it, get rid of the range checking for family numbers.
We just document the known to exist cores running Linux and ditch
others.
With this in place, we add detection of ARC750 which is
- cores 0x33 and before
- cores 0x34 and later with MMUv2
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
This came to light when helping a customer with oldish ARC750 core who
were getting instruction errors because of lack of SWAPE but boot log
was incorrectly printing it as being present
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
On older arc700 cores, some of the features configured were not present
in Build config registers. To print about them at boot, we just use the
Kconfig option i.e. whether linux is built to use them or not.
So yes this seems bogus, but what else can be done. Moreover if linux is
booting with these enabled, then the Kconfig info is a good indicator
anyways.
Over time these "hacks" accumulated in read_arc_build_cfg_regs() as well
as arc_cpu_mumbojumbo(). so refactor and move all of those in a single
place: read_arc_build_cfg_regs(). This causes some code redcution too:
| bloat-o-meter2 arch/arc/kernel/setup.o.0 arch/arc/kernel/setup.o.1
| add/remove: 0/0 grow/shrink: 2/1 up/down: 64/-132 (-68)
| function old new delta
| setup_processor 610 670 +60
| cpuinfo_arc700 76 80 +4
| arc_cpu_mumbojumbo 752 620 -132
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Previously we would not print the case when IOC existed but was not
enabled.
And while at it, reduce one line off boot printing by consolidating
the Peripheral address space and IO-Coherency which in a way
applies to them
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Its all generic atomic_long_t stuff now.
Tested-by: Jason Low <jason.low2@hpe.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
if user disables IOC from debugger at startup (by clearing @ioc_enable),
@ioc_exists is cleared too. This means boot prints don't capture the
fact that IOC was present but disabled which could be misleading.
So invert how we use @ioc_enable and @ioc_exists and make it more
canonical. @ioc_exists represent whether hardware is present or not and
stays same whether enabled or not. @ioc_enable is still user driven,
but will be auto-disabled if IOC hardware is not present, i.e. if
@ioc_exist=0. This is opposite to what we were doing before, but much
clearer.
This means @ioc_enable is now the "exported" toggle in rest of code such
as dma mapping API.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Older ARC700 cores (ARC750 specifically) lack instructions to implement
atomic r-w-w. This is problematic for userspace libraries such as NPTL
which need atomic primitives. So enable them by providing kernel assist.
This is costly but really the only sane soluton (othern than tight
spinning using the otherwise availiable atomic exchange EX instruciton).
Good thing is there are only a few of these cores running Linux out in
the wild.
This only works on UP systems.
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
The cast valid since TASK_SIZE * 2 will never actually cause overflow.
| CC fs/binfmt_elf.o
| In file included from ../include/linux/elf.h:4:0,
| from ../include/linux/module.h:15,
| from ../fs/binfmt_elf.c:12:
| ../fs/binfmt_elf.c: In function load_elf_binar:
| ../arch/arc/include/asm/elf.h:57:29: warning: integer overflow in expression [-Woverflow]
| #define ELF_ET_DYN_BASE (2 * TASK_SIZE / 3)
| ^
| ../fs/binfmt_elf.c:921:16: note: in expansion of macro ELF_ET_DYN_BASE
| load_bias = ELF_ET_DYN_BASE - vaddr;
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
The IDU intc is technically part of MCIP (Multi-core IP) hence
historically was only available in a SMP hardware build (and thus only
in a SMP kernel build). Now that hardware restriction has been lifted,
so a UP kernel needs to support it.
This requires breaking mcip.c into parts which are strictly SMP
(inter-core interrupts) and IDU which in reality is just another
intc and thus has no bearing on SMP.
This change allows IDU in UP builds and with a suitable device tree, we
can have the cascaded intc system
ARCv2 core intc <---> ARCv2 IDU intc <---> periperals
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Summary of PCI changes for the v4.9 merge window:
Enumeration:
- microblaze: Add multidomain support for procfs (Bharat Kumar Gogada)
Resource management:
- Ignore requested alignment for PROBE_ONLY and fixed resources (Yongji Xie)
- Ignore requested alignment for VF BARs (Yongji Xie)
PCI device hotplug:
- Make core explicitly non-modular (Paul Gortmaker)
PCIe native device hotplug:
- Rename pcie_isr() locals for clarity (Bjorn Helgaas)
- Return IRQ_NONE when we can't read interrupt status (Bjorn Helgaas)
- Remove unnecessary guard (Bjorn Helgaas)
- Clean up dmesg "Slot(%s)" messages (Bjorn Helgaas)
- Remove useless pciehp_get_latch_status() calls (Bjorn Helgaas)
- Clear attention LED on device add (Keith Busch)
- Allow exclusive userspace control of indicators (Keith Busch)
- Process all hotplug events before looking for new ones (Mayurkumar Patel)
- Don't re-read Slot Status when queuing hotplug event (Mayurkumar Patel)
- Don't re-read Slot Status when handling surprise event (Mayurkumar Patel)
- Make explicitly non-modular (Paul Gortmaker)
Power management:
- Afford direct-complete to devices with non-standard PM (Lukas Wunner)
- Query platform firmware for device power state (Lukas Wunner)
- Recognize D3cold in pci_update_current_state() (Lukas Wunner)
- Avoid unnecessary resume after direct-complete (Lukas Wunner)
- Make explicitly non-modular (Paul Gortmaker)
Virtualization:
- Mark Atheros AR9580 to avoid bus reset (Maik Broemme)
- Check for pci_setup_device() failure in pci_iov_add_virtfn() (Po Liu)
MSI:
- Enable PCI_MSI_IRQ_DOMAIN support for ARC (Joao Pinto)
AER:
- Remove aerdriver.nosourceid kernel parameter (Bjorn Helgaas)
- Remove aerdriver.forceload kernel parameter (Bjorn Helgaas)
- Fix aer_probe() kernel-doc comment (Cao jin)
- Add bus flag to skip source ID matching (Jon Derrick)
- Avoid memory allocation in interrupt handling path (Jon Derrick)
- Cache capability position (Keith Busch)
- Make explicitly non-modular (Paul Gortmaker)
- Remove duplicate AER severity translation (Tyler Baicar)
- Send correct severity to calculate AER severity (Tyler Baicar)
Precision Time Measurement:
- Add Precision Time Measurement (PTM) support (Jonathan Yong)
- Add PTM clock granularity information (Bjorn Helgaas)
- Add pci_enable_ptm() for drivers to enable PTM on endpoints (Bjorn Helgaas)
Generic host bridge driver:
- Fix pci_remap_iospace() failure path (Lorenzo Pieralisi)
- Make explicitly non-modular (Paul Gortmaker)
Altera host bridge driver:
- Remove redundant platform_get_resource() return value check (Bjorn Helgaas)
- Poll for link training status after retraining the link (Ley Foon Tan)
- Rework config accessors for use without a struct pci_bus (Ley Foon Tan)
- Move retrain from fixup to altera_pcie_host_init() (Ley Foon Tan)
- Make MSI explicitly non-modular (Paul Gortmaker)
- Make explicitly non-modular (Paul Gortmaker)
- Relax device number checking to allow SR-IOV (Po Liu)
ARM Versatile host bridge driver:
- Fix pci_remap_iospace() failure path (Lorenzo Pieralisi)
Axis ARTPEC-6 host bridge driver:
- Drop __init from artpec6_add_pcie_port() (Niklas Cassel)
Freescale i.MX6 host bridge driver:
- Make explicitly non-modular (Paul Gortmaker)
Intel VMD host bridge driver:
- Add quirk for AER to ignore source ID (Jon Derrick)
- Allocate IRQ lists with correct MSI-X count (Jon Derrick)
- Convert to use pci_alloc_irq_vectors() API (Jon Derrick)
- Eliminate vmd_vector member from list type (Jon Derrick)
- Eliminate index member from IRQ list (Jon Derrick)
- Synchronize with RCU freeing MSI IRQ descs (Keith Busch)
- Request userspace control of PCIe hotplug indicators (Keith Busch)
- Move VMD driver to drivers/pci/host (Keith Busch)
Marvell Aardvark host bridge driver:
- Fix pci_remap_iospace() failure path (Lorenzo Pieralisi)
- Remove redundant dev_err call in advk_pcie_probe() (Wei Yongjun)
Microsoft Hyper-V host bridge driver:
- Use zero-length array in struct pci_packet (Dexuan Cui)
- Use pci_function_description[0] in struct definitions (Dexuan Cui)
- Remove the unused 'wrk' in struct hv_pcibus_device (Dexuan Cui)
- Handle vmbus_sendpacket() failure in hv_compose_msi_msg() (Dexuan Cui)
- Handle hv_pci_generic_compl() error case (Dexuan Cui)
- Use list_move_tail() instead of list_del() + list_add_tail() (Wei Yongjun)
NVIDIA Tegra host bridge driver:
- Fix pci_remap_iospace() failure path (Lorenzo Pieralisi)
- Remove redundant _data suffix (Thierry Reding)
- Use of_device_get_match_data() (Thierry Reding)
Qualcomm host bridge driver:
- Make explicitly non-modular (Paul Gortmaker)
Renesas R-Car host bridge driver:
- Consolidate register space lookup and ioremap (Bjorn Helgaas)
- Don't disable/unprepare clocks on prepare/enable failure (Geert Uytterhoeven)
- Add multi-MSI support (Grigory Kletsko)
- Fix pci_remap_iospace() failure path (Lorenzo Pieralisi)
- Fix some checkpatch warnings (Sergei Shtylyov)
- Try increasing PCIe link speed to 5 GT/s at boot (Sergei Shtylyov)
Rockchip host bridge driver:
- Add DT bindings for Rockchip PCIe controller (Shawn Lin)
- Add Rockchip PCIe controller support (Shawn Lin)
- Improve the deassert sequence of four reset pins (Shawn Lin)
- Fix wrong transmitted FTS count (Shawn Lin)
- Increase the Max Credit update interval (Rajat Jain)
Samsung Exynos host bridge driver:
- Make explicitly non-modular (Paul Gortmaker)
ST Microelectronics SPEAr13xx host bridge driver:
- Make explicitly non-modular (Paul Gortmaker)
Synopsys DesignWare host bridge driver:
- Return data directly from dw_pcie_readl_rc() (Bjorn Helgaas)
- Exchange viewport of `MEMORYs' and `CFGs/IOs' (Dong Bo)
- Check LTSSM training bit before deciding link is up (Jisheng Zhang)
- Move link wait definitions to .c file (Joao Pinto)
- Wait for iATU enable (Joao Pinto)
- Add iATU Unroll feature (Joao Pinto)
- Fix pci_remap_iospace() failure path (Lorenzo Pieralisi)
- Make explicitly non-modular (Paul Gortmaker)
- Relax device number checking to allow SR-IOV (Po Liu)
- Keep viewport fixed for IO transaction if num_viewport > 2 (Pratyush Anand)
- Remove redundant platform_get_resource() return value check (Wei Yongjun)
TI DRA7xx host bridge driver:
- Make explicitly non-modular (Paul Gortmaker)
TI Keystone host bridge driver:
- Propagate request_irq() failure (Wei Yongjun)
Xilinx AXI host bridge driver:
- Keep both legacy and MSI interrupt domain references (Bharat Kumar Gogada)
- Clear interrupt register for invalid interrupt (Bharat Kumar Gogada)
- Clear correct MSI set bit (Bharat Kumar Gogada)
- Dispose of MSI virtual IRQ (Bharat Kumar Gogada)
- Make explicitly non-modular (Paul Gortmaker)
- Relax device number checking to allow SR-IOV (Po Liu)
Xilinx NWL host bridge driver:
- Expand error logging (Bharat Kumar Gogada)
- Enable all MSI interrupts using MSI mask (Bharat Kumar Gogada)
- Make explicitly non-modular (Paul Gortmaker)
Miscellaneous:
- Drop CONFIG_KEXEC_CORE ifdeffery (Lukas Wunner)
- portdrv: Make explicitly non-modular (Paul Gortmaker)
- Make DPC explicitly non-modular (Paul Gortmaker)"
* tag 'pci-v4.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (105 commits)
x86/PCI: VMD: Move VMD driver to drivers/pci/host
PCI: rockchip: Fix wrong transmitted FTS count
PCI: rockchip: Improve the deassert sequence of four reset pins
PCI: rockchip: Increase the Max Credit update interval
PCI: rcar: Try increasing PCIe link speed to 5 GT/s at boot
PCI/AER: Fix aer_probe() kernel-doc comment
PCI: Ignore requested alignment for VF BARs
PCI: Ignore requested alignment for PROBE_ONLY and fixed resources
PCI: Avoid unnecessary resume after direct-complete
PCI: Recognize D3cold in pci_update_current_state()
PCI: Query platform firmware for device power state
PCI: Afford direct-complete to devices with non-standard PM
PCI/AER: Cache capability position
PCI/AER: Avoid memory allocation in interrupt handling path
x86/PCI: VMD: Request userspace control of PCIe hotplug indicators
PCI: pciehp: Allow exclusive userspace control of indicators
ACPI / APEI: Send correct severity to calculate AER severity
PCI/AER: Remove duplicate AER severity translation
x86/PCI: VMD: Synchronize with RCU freeing MSI IRQ descs
x86/PCI: VMD: Eliminate index member from IRQ list
...
|
|
Commit d9676fa152c83b ("ARCv2: Enable LOCKDEP"), changed
local_save_flags() to not return raw STATUS32 but encoded in the form
such that it could be fed directly to CLRI/SETI instructions.
However the STATUS32.E[] was not captured correctly as it corresponds to
bits [4:1] in the register and not [3:0]
Fixes: d9676fa152c83b ("ARCv2: Enable LOCKDEP")
Cc: Evgeny Voevodin <evgeny.voevodin@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
1. detect whether binutils supports the cfi pseudo ops
2. define conditional macros to generate the ops
3. define new ENTRY_CFI/END_CFI to annotate hand asm code.
- Needed because we don't want to emit dwarf info in general ENTRY/END
used by lowest level trap/exception/interrutp handlers as unwinder
gets confused trying to unwind out of them. We want unwinder to
instead stop when it hits onfo those routines
- These provide minimal start/end cfi ops assuming routine doesn't
touch stack memory/regs
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
We used to live with PERF_COUNT_HW_CACHE_REFERENCES and
PERF_COUNT_HW_CACHE_REFERENCES not specified on ARC.
Those events are actually aliases to 2 cache events that we do support
and so this change sets "cache-reference" and "cache-misses" events
in the same way as "L1-dcache-loads" and L1-dcache-load-misses.
And while at it adding debug info for cache events as well as doing a
subtle fix in HW events debug info - config value is much better
represented by hex so we may see not only event index but as well other
control bits set (if they exist).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Build brekeage since last changes to generic atomic operations.
Added couple of missing macros which are now mandatory
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
ARCv2 ISA provides 64-bit exclusive load/stores so use them to implement
the 64-bit atomics and elide the spinlock based generic 64-bit atomics
boot tested with atomic64 self-test (and GOD bless the person who wrote
them, I realized my inline assmebly is sloppy as hell)
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
HS release 3.0 provides for even more flexibility in specifying the
volatile address space for mapping peripherals.
With HS 2.1 @start was made flexible / programmable - with HS 3.0 even
@end can be setup (vs. fixed to 0xFFFF_FFFF before).
So add code to reflect that and while at it remove an unused struct
defintion
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull uaccess fixes from Al Viro:
"Fixes for broken uaccess primitives - mostly lack of proper zeroing
in copy_from_user()/get_user()/__get_user(), but for several
architectures there's more (broken clear_user() on frv and
strncpy_from_user() on hexagon)"
* 'uaccess-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (28 commits)
avr32: fix copy_from_user()
microblaze: fix __get_user()
microblaze: fix copy_from_user()
m32r: fix __get_user()
blackfin: fix copy_from_user()
sparc32: fix copy_from_user()
sh: fix copy_from_user()
sh64: failing __get_user() should zero
score: fix copy_from_user() and friends
score: fix __get_user/get_user
s390: get_user() should zero on failure
ppc32: fix copy_from_user()
parisc: fix copy_from_user()
openrisc: fix copy_from_user()
nios2: fix __get_user()
nios2: copy_from_user() should zero the tail of destination
mn10300: copy_from_user() should zero on access_ok() failure...
mn10300: failing __get_user() and get_user() should zero
mips: copy_from_user() must zero the destination on access_ok() failure
ARC: uaccess: get_user to zero out dest in cause of fault
...
|
|
Al reported potential issue with ARC get_user() as it wasn't clearing
out destination pointer in case of fault due to bad address etc.
Verified using following
| {
| u32 bogus1 = 0xdeadbeef;
| u64 bogus2 = 0xdead;
| int rc1, rc2;
|
| pr_info("Orig values %x %llx\n", bogus1, bogus2);
| rc1 = get_user(bogus1, (u32 __user *)0x40000000);
| rc2 = get_user(bogus2, (u64 __user *)0x50000000);
| pr_info("access %d %d, new values %x %llx\n",
| rc1, rc2, bogus1, bogus2);
| }
| [ARCLinux]# insmod /mnt/kernel-module/qtn.ko
| Orig values deadbeef dead
| access -14 -14, new values 0 0
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Add ARC as an arch that supports PCI_MSI_IRQ_DOMAIN and add generation of
msi.h in the ARC arch.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
|
|
| CC mm/memory.o
| In file included from ../mm/memory.c:53:0:
| ../include/linux/pfn_t.h: In function ‘pfn_t_pte’:
| ../include/linux/pfn_t.h:78:2: error: conversion to non-scalar type requested
| return pfn_pte(pfn_t_to_pfn(pfn), pgprot);
With STRICT_MM_TYPECHECKS pte_t is a struct and the offending code
forces a cast which ends up shifting a struct and hence the gcc warning.
Note that in recent past some of the arches (aarch64, s390) made
STRICT_MM_TYPECHECKS default, but we don't for ARC as this leads to slightly
worse generated code, given ARC ABI definition of returning structs
(which pte_t would become)
Quoting from ARC ABI...
"Results of type struct are returned in a caller-supplied temporary
variable whose address is passed in r0.
For such functions, the arguments are shifted so that they are
passed in r1 and up."
So
- struct to be returned would be allocated on stack requiring extra
code at call sites
- callee updates stack memory to facilitate the return (vs. simple
MOV into return reg r0)
Hence STRICT_MM_TYPECHECKS is not enabled by default for ARC
Cc: <stable@vger.kernel.org> #4.4+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
The syscall ABI includes the gcc functional calling ABI since a syscall
implies userland caller and kernel callee.
The current gcc ABI (v3) for ARCv2 ISA required 64-bit data be passed in
even-odd register pairs, (potentially punching reg holes when passing such
values as args). This was partly driven by the fact that the double-word
LDD/STD instructions in ARCv2 expect the register alignment and thus gcc
forcing this avoids extra MOV at the cost of a few unused register (which we
have plenty anyways).
This however was rejected as part of upstreaming gcc port to HS. So the new
ABI v4 doesn't enforce the even-odd reg restriction.
Do note that for ARCompact ISA builds v3 and v4 are practically the same in
terms of gcc code generation.
In terms of change management, we infer the new ABI if gcc 6.x onwards
is used for building the kernel.
This also needs a stable backport to enable older kernels to work with
new tools/user-space
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
User mode callee regs are explicitly collected before signal delivery or
breakpoint trap. r25 is special for kernel as it serves as task pointer,
so user mode value is clobbered very early. It is saved in pt_regs where
generally only scratch (aka caller saved) regs are saved.
The code to access the corresponding pt_regs location had a subtle bug as
it was using load/store with scaling of offset, whereas the offset was already
byte wise correct. So fix this by replacing LD.AS with a standard LD
Cc: <stable@vger.kernel.org>
Signed-off-by: Liav Rehana <liavr@mellanox.com>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
[vgupta: rewrote title and commit log]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
trace_hardirqs_on_caller() in lockdep.c expects to be called before, not
after interrupts are actually enabled.
The following comment in kernel/locking/lockdep.c substantiates this
claim:
"
/*
* We're enabling irqs and according to our state above irqs weren't
* already enabled, yet we find the hardware thinks they are in fact
* enabled.. someone messed up their IRQ state tracing.
*/
"
An example can be found in include/linux/irqflags.h:
do { trace_hardirqs_on(); raw_local_irq_enable(); } while (0)
Without this change, we hit the following DEBUG_LOCKS_WARN_ON.
[ 7.760000] ------------[ cut here ]------------
[ 7.760000] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2711 resume_user_mode_begin+0x48/0xf0
[ 7.770000] DEBUG_LOCKS_WARN_ON(!irqs_disabled())
[ 7.780000] Modules linked in:
[ 7.780000] CPU: 0 PID: 1 Comm: init Not tainted 4.7.0-00003-gc668bb9-dirty #366
[ 7.790000]
[ 7.790000] Stack Trace:
[ 7.790000] arc_unwind_core.constprop.1+0xa4/0x118
[ 7.800000] warn_slowpath_fmt+0x72/0x158
[ 7.800000] resume_user_mode_begin+0x48/0xf0
[ 7.810000] ---[ end trace 6f6a7a8fae20d2f0 ]---
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Things have been calm here - nothing much except for a few fixes"
* tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: don't loose PTE_SPECIAL in pte_modify()
ARC: dma: fix address translation in arc_dma_free
ARC: typo fix in mm/ioremap.c
ARC: fix linux-next build breakage
|
|
LTP madvise05 was generating mm splat
| [ARCLinux]# /sd/ltp/testcases/bin/madvise05
| BUG: Bad page map in process madvise05 pte:80e08211 pmd:9f7d4000
| page:9fdcfc90 count:1 mapcount:-1 mapping: (null) index:0x0 flags: 0x404(referenced|reserved)
| page dumped because: bad pte
| addr:200b8000 vm_flags:00000070 anon_vma: (null) mapping: (null) index:1005c
| file: (null) fault: (null) mmap: (null) readpage: (null)
| CPU: 2 PID: 6707 Comm: madvise05
And for newer kernels, the system was rendered unusable afterwards.
The problem was mprotect->pte_modify() clearing PTE_SPECIAL (which is
set to identify the special zero page wired to the pte).
When pte was finally unmapped, special casing for zero page was not
done, and instead it was treated as a "normal" page, tripping on the
map counts etc.
This fixes ARC STAR 9001053308
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|