Age | Commit message (Collapse) | Author | Files | Lines |
|
Now that the i2c-bcm-iproc driver has been fixed to permit reading more
than 63 bytes in a single transaction with commit fd01eecdf959 ("i2c:
iproc: Fix i2c master read more than 63 bytes") we no longer need to
bitbang i2c over GPIOs which was necessary before to allow the
PHYLINK/SFP subsystems to read SFP modules.
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
All boards replicate the aliases node, move the aliases node to
bcm-nsp.dtsi and add all the serial and ethernet ports such that a boot
program like u-boot can populate MAC addresses accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Enable the SFP connected to port 5 of the switch and wire up all GPIOs
to the SFP cage. Because of a hardware limitation of the i2c controller
on the iProc SoCs which prevents large i2c (> 63 bytes) transactions to
work, we use the i2c-gpio interface instead, which does not have that
limitation. This allows us to read the SFP module EEPROM, which would
not be possible otherwise since it exceeds that size during a single
read transfer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
|
|
https://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.17" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs devicetree changes
for 4.17, please pull the following:
- Henry fixes the pin functions for the JTAG pins, nothing uses this for
now, but it could be backported eventually if deemed appropriate
- Stefan fixes the register ranges for the bcm2835-i2s nodes in the
binding document definition, he then fixes the probing of the
bcm2835-i2s driver by providing an appropriate register range and a
missing clock. Stefan also makes sure that the appropriate pull
settings are applied to the pins used on the Raspberry Pi Zero
Wireless, he then adds the necessary UART node to connected to the
BCM43438 Bluetooth adapter on the Pi Zero W. He finally enables USB
OTG mode on the Pi Zero W since he became usable again
- Baruch adds the necessary Device Tree nodes to support the Raspberry
Pi GPIO expander which is controlled via the VC4 firmware
- Hiroshi adds the missing LEDs on the Buffalo WZR-900DHP router
- Eric adds the DPI hardware block into the BCM283x Device Tree include
file for future use when an actual panel is available
- Florian updates the Northstar Plus platforms to use port 8 of the
internal switch as the CPU/management port since necessary code was
added in the b53 switch driver to support that
* tag 'arm-soc/for-4.17/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: NSP: Switch to port 8 for CPU port
ARM: bcm2835: Add the DPI hardware to the device tree.
ARM: dts: BCM5301X: add missing LEDs for Buffalo WZR-900DHP
ARM: dts: bcm2835-rpi-zero-w: Enable OTG mode
ARM: dts: bcm2835-rpi-zero-w: Add bcm43438 serial slave
ARM: dts: bcm283x: Apply pull settings to Zero W relevant groups
ARM: dts: bcm2837-rpi-3-b: add GPIO expander
ARM: dts: bcm2835: make the firmware node into a bus
ARM: dts: bcm283x: Fix probing of bcm2835-i2s
dt-bindings: bcm283x: Fix register ranges of bcm2835-i2s
ARM: dts: bcm283x: Fix pin function of JTAG pins
|
|
Now that we have added support for pre-pended Broadcom tags with commit
11606039604c ("net: dsa: b53: Support prepended Broadcom tags") we can
switch all the Northstar Plus reference boards to use port 8 for the CPU
port. This allows us to prepare room for supporting the Flow Accelerator
2 NAPT offload, and frees up port 5 to be made fully configurable for
the modes that it supports: internal, SGMII, RGMII etc.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.
The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.
Fixes: c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The AHCI controller is currently enabled for all of these boards:
bcm958623hr and bcm958625hr would result in a hard hang on boot that we
cannot get rid of. Since this does not appear to have an easy and simple
fix, just disable the AHCI controller for now until this gets resolved.
Fixes: 70725d6e97ac ("ARM: dts: NSP: Enable SATA on bcm958625hr")
Fixes: d454c3762437 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This uses the existing Northstar USB3 PHY driver to enable the USB3
ports on NSP.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved
over from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288
SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology
DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more
description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using
arm/ and arm64/ as include prefixes. This will avoid other local hacks
such as per-file links between the two arch trees (this broke for
external mirroring of DT contents). Now they can just provide their
own appropriate dt-include hierarcy per platform"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (349 commits)
ARM: dts: exynos: Use - instead of @ for DT OPP entries
arm: spear6xx: add DT description of the ADC on SPEAr600
arm: spear6xx: remove unneeded pinctrl properties in spear600-evb
arm: spear6xx: switch spear600-evb to the new flash partition DT binding
arm: spear6xx: fix spaces in spear600-evb.dts
arm: spear6xx: use node labels in spear600-evb.dts
arm: spear6xx: add labels to various nodes in spear600.dtsi
ARM: dts: vexpress: fix few unit address format warnings
ARM: dts: at91: sama5d3_xplained: not all ADC channels are available
ARM: dts: at91: sama5d3_xplained: fix ADC vref
ARM: dts: at91: add envelope detector mux to the Axentia TSE-850
ARM: dts: armada-38x: label USB and SATA nodes
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
...
|
|
Add the EHCI and OHCI entries to the Northstar Plus device tree files.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The libgpio code pre-sets the GPIO values for the gpio-reset in the
device tree. This results in the device being reset during bringup.
To prevent this pre-setting, use the "open-source" flag in the device
tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: b1aaf88 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file")
Fixes: 10baed1 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file")
Fixes: 088e3148 ("ARM: dts: NSP: Add new DT file for bcm958522er")
Fixes: e3227c1 ("ARM: dts: NSP: Add new DT file for bcm958525er")
Fixes: 2f8bc00 ("ARM: dts: NSP: Add new DT file for bcm958622hr")
Fixes: d454c37 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Fixes: f27eacf ("ARM: dts: NSP: Add new DT file for bcm988312hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add and enable the third AMAC ethernet interface in the device trees for
the platforms where it is present. Also, enable amac1 on some of the
platforms where that was missing.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
QSPI device tree entries are present in bcm958625k, but missing from
bcm958522er, bcm958525er, bcm958525xmc, bcm958622hr, bcm958623hr,
bcm958625hr, and bcm988312hr. Duplicate the entry in bcm958625k for
all of those that are missing it (as they are identical).
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The QSPI entry was added out of the sequental order that the rest of the
DTSI file is in. Move it to make it fit in properly. Also, some other
entries have been added in a non-alphabetical order in the DTS files,
making them different from the other NSP DTS files. Move the relevant
peices to make it match. Finally, remove errant new lines.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add the ability to reboot the bcm958625hr board via GPIO.
Unfortunately, not all of the NSP based boards use the same GPIO pin and
one doesn't have the ability to reboot via GPIO at all. So, this will
need to be specified per DTS file.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add SATA support to bcm958625hr DTS
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The BCM958625HR board has 2GB of RAM available. Increase the amount
from 512MB to 2GB and add the device type to the memory entry.
Fixes: 9a4865d42fe5 ("ARM: dts: NSP: Specify RAM amount for BCM958625HR board")
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add the layout of the switch ports found on the BCM958625HR reference
board. The CPU port is hooked up to the AMAC0 Ethernet controlelr
adapter, so we also enable it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add 512MB of memory starting at physical offset 0x6000_0000.
Fixes: 65e9ac208c8e ("ARM: dts: NSP: Add new DT file for bcm958625hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Create a new device tree file for the Broadcom Northstar Plus HR SVK.
This SVK is a smaller form factor, and thus only has 2 PCI slots and 1
UART. Also, it has the ability to reboot via GPIO (instead of the
processor reset).
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|