| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.
There's no change to dtbs_install as the flat structure is maintained on
install.
The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
company (e.g. gemini, nspire)
The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add aliases for eMMC, SD card and WiFi where applicable, so that
assigned mmc indeces are always the same.
Co-developed-by: Anton Bambura <jenneron@protonmail.com>
Signed-off-by: Anton Bambura <jenneron@protonmail.com>
[ Tested on exynos5800-peach-pi ]
Tested-by: Valentine Iourine <iourine@iourine.msk.su>
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20230402144724.17839-3-henrik@grimler.se
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
By convention the hex addresses should be lowercase.
Link: https://lore.kernel.org/r/20230125094513.155063-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
DT schema expects names of operating points tables to match certain
pattern:
exynos5422-odroidxu3-lite.dtb: opp-table0: $nodename:0: 'opp-table0' does not match '^opp-table(-[a-z0-9]+)?$'
Link: https://lore.kernel.org/r/20230120064724.40621-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Passing maximum frequency of LPDDR3 memory timings as unit address was
deprecated in favor of 'max-freq' property.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20220206135918.211990-1-krzysztof.kozlowski@canonical.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung pinctrl DTS and driver changes for v5.18
Conversion of Samsung pinctrl bindings to dtschema followed up with
alignment of DTS files to the dtschema.
The entire work consists of three parts but everything should be merged
at once to avoid dtschema check errors:
1. Samsung pinctrl driver change necessary to accept new DTS (driver
depends on node names and this has to be adjusted because of dtschema).
2. Conversion to dtschema which brings requirement of different naming
of the GPIO nodes.
3. DTS commits depending on driver (1) above, which convert all GPIO pin
bank names to new naming, required by dtschema.
This also includes few cleanups around DTS which are here to avoid
any merge conflicts.
The Samsung pinctrl driver changes are backwards compatible. However
the DTS changes (renaming nodes) could cause problems in out-of-tree or
other project implementations of the driver.
* tag 'samsung-dt-pinctrl-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (28 commits)
arm64: dts: exynos: use dedicated wake-up pinctrl compatible in ExynosAutov9
ARM: dts: s5pv210: align pinctrl with dtschema
ARM: dts: s3c64xx: align pinctrl with dtschema
ARM: dts: s3c24xx: align pinctrl with dtschema
arm64: dts: exynos: align pinctrl with dtschema in ExynosAutov9
arm64: dts: exynos: align pinctrl with dtschema in Exynos7
arm64: dts: exynos: align pinctrl with dtschema in Exynos5433
ARM: dts: exynos: align pinctrl with dtschema in Exynos542x/5800
ARM: dts: exynos: align pinctrl with dtschema in Exynos5410
ARM: dts: exynos: align pinctrl with dtschema in Exynos5260
ARM: dts: exynos: align pinctrl with dtschema in Exynos5250
ARM: dts: exynos: align pinctrl with dtschema in Exynos4412
ARM: dts: exynos: align pinctrl with dtschema in Exynos4210
ARM: dts: exynos: align pinctrl with dtschema in Exynos3250
ARM: dts: s3c64xx: drop unneeded pinctrl wake-up interrupt mapping
ARM: dts: exynos: simplify PMIC DVS pin configuration in Peach Pi
ARM: dts: exynos: override pins by label in Peach Pi
ARM: dts: exynos: simplify PMIC DVS pin configuration in Peach Pit
ARM: dts: exynos: override pins by label in Peach Pit
ARM: dts: exynos: simplify PMIC DVS pin configuration in Odroid XU
...
Link: https://lore.kernel.org/r/20220129115352.13274-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The node names should have generic name, so use "timings" for LPDDR3
timings. This will also be required by dtschema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220201114749.88500-1-krzysztof.kozlowski@canonical.com
|
|
Align the pin controller related nodes with dtschema. No functional
change expected.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220111201722.327219-10-krzysztof.kozlowski@canonical.com
|
|
The RTC on S2MPS11 PMIC on Odroid XU3/XU4 family of boards can wakeup
the system from suspend to RAM. Add a generic property for this.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210420164943.11152-10-krzysztof.kozlowski@canonical.com
|
|
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: aac4e0615341 ("ARM: dts: odroidxu3: Enable wake alarm of S2MPS11 RTC")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-6-krzk@kernel.org
|
|
Use hyphens instead of underscores in the Exynos5250 and Exynos542x node
names which is expected by naming convention, multiple dtschema files
and pointed out by dtc W=2 builds.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201105184506.215648-4-krzk@kernel.org
|
|
The Devicetree specification expects device node names to have a generic
name, representing the class of a device. Also the convention for node
names is to use hyphens, not underscores.
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201027170947.132725-9-krzk@kernel.org
|
|
Remove double space after '=' and fix indentation in Exynos5250,
Exynos5410 and Exynos5420 DTS files.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-7-krzk@kernel.org
|
|
Commit 1019fe2c7280 ("ARM: dts: exynos: Adjust bus related OPPs to the
values correct for Exynos5422 Odroids") changed the parameters of the
OPPs for the FSYS bus. Besides the frequency adjustments, it also removed
the 'shared-opp' property from the OPP table used for FSYS_APB and FSYS
busses.
This revealed that in fact the FSYS bus frequency scaling never worked.
When one OPP table is marked as 'opp-shared', only the first bus which
selects the OPP sets the rate of its clock. Then OPP core assumes that
the other busses have been changed to that OPP and no change to their
clock rates are needed. Thus when FSYS_APB bus, which was registered
first, set the rate for its clock, the OPP core did not change the FSYS
bus clock later.
The mentioned commit removed that behavior, what introduced a regression
on some Odroid XU3 boards. Frequency scaling of the FSYS bus causes
instability of the USB host operation, what can be observed as network
hangs. To restore old behavior, simply disable frequency scaling for the
FSYS bus.
Reported-by: Willy Wolff <willy.mh.wolff.ml@gmail.com>
Fixes: 1019fe2c7280 ("ARM: dts: exynos: Adjust bus related OPPs to the values correct for Exynos5422 Odroids")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
G3D power domain in Exynos5422 SoC is supplied from VDD_G3D. Besides the
main GPU MALI module it also contains the power domain control logic and
clocks. Turning the VDD_G3D power supply off causes the power domain to
fail to operate properly and breaks for example system suspend/resume.
GPU should use VDD_G3D supply mainly to control the DVFS.
Fixes: 1a5a85c56402 ("ARM: dts: exynos: Add Mali/GPU node on Exynos5420 and enable it on Odroid XU3/4")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.6
1. Couple ARM and wcore bus regulators on Exynos542x so higher
frequencies could be used with dynamic voltage and frequency scaling.
Enable this higher frequencies.
2. Correct the polarity of USB3503 hub GPIOs.
3. Adjust the bus frequencies (scaled with devfreq framework) on
Exynos5422 Odroid boards to match values possible to obtain from root
PLLs.
4. Add display to Tiny4412 board.
5. Cleanups and minor improvements.
* tag 'samsung-dt-5.6' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Enable FIMD node and add proper panel node to Tiny4412
ARM: dts: samsung: Rename Samsung and Exynos to lowercase
ARM: dts: exynos: Adjust bus related OPPs to the values correct for Exynos5422 Odroids
ARM: dts: exynos: Move Exynos5420 bus related OPPs to the Odroid boards DTS
ARM: dts: exynos: Correct USB3503 GPIOs polarity
ARM: dts: exynos: Add missing CPU frequencies for Exynos5422/5800
ARM: dts: exynos: Add initial data for coupled regulators for Exynos5422/5800
ARM: dts: exynos: Remove syscon compatible from chipid node on Exynos5
Link: https://lore.kernel.org/r/20200110172334.4767-3-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Exynos5422 Odroids
Hardkernel's Odroid XU3/XU4/HC1 boards use bootloader, which configures
top PLLs to the following values: MPLL: 532MHz, CPLL: 666MHz and DPLL:
600MHz.
Adjust all bus related OPPs to the values that are possible to derive
from the top PLL configured by the bootloader. Also add a comment for
each bus describing which PLL is used for it.
The most significant change is the highest rate for wcore bus. It has
been increased to 532MHz as this is the value configured initially by
the bootloader. Also the voltage for this OPP is changed to match the
value set by the bootloader.
This patch finally allows the buses to operate on the rates matching the
values set for each OPP and fixes the following warnings observed on
boot:
exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz)
exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz)
exynos-bus: new bus device registered: soc:bus_fsys_apb (100000 KHz ~ 200000 KHz)
...
exynos-bus soc:bus_wcore: dev_pm_opp_set_rate: failed to find current OPP for freq 532000000 (-34)
exynos-bus soc:bus_noc: dev_pm_opp_set_rate: failed to find current OPP for freq 111000000 (-34)
exynos-bus soc:bus_fsys_apb: dev_pm_opp_set_rate: failed to find current OPP for freq 222000000 (-34)
The problem with setting incorrect (in some cases much lower) clock rate
for the defined OPP were there from the beginning, but went unnoticed
because the only way to observe it was to manually check the rate of the
respective clocks. The commit 4294a779bd8d ("PM / devfreq: exynos-bus:
Convert to use dev_pm_opp_set_rate()") finally revealed it, because it
enabled use of the generic code from the OPP framework, which issues the
above mentioned warnings.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Currently the only Exynos5422-based boards that support bus frequency
scaling are Hardkernel's Odroid XU3/XU4/HC1. Move the bus related OPPs
to the boards DTS, because those OPPs heavily depend on the clock
topology and top PLL rates, which are being configured by the board's
bootloader.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Declare Exynos5422/5800 voltage ranges for OPPs for big CPUs
(Cortex-A15) and wcore bus. Couple their voltage supplies as vdd_arm
and vdd_int should be in 300 mV range.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[k.konieczny: add missing patch description]
Signed-off-by: Kamil Konieczny <k.konieczny@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.5, part 2
1. Cleanup by adjusting DTS to bindings,
2. Add touch-sensitive buttons to Midas (Galaxy S III family phones),
3. Add GPU/Mali to Exynos542x and Odroid XU3/XU4 family.
* tag 'samsung-dt-5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add Mali/GPU node on Exynos5420 and enable it on Odroid XU3/4
ARM: dts: exynos: Add support for the touch-sensitive buttons on Midas family
ARM: dts: exynos: Rename children of SysRAM node to "sram"
Link: https://lore.kernel.org/r/20191119142026.7190-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add device tree node for Mali GPU on Exynos 542x SoC family. GPU is
disabled by default, and is enabled for each board after the regulator
is defined. Tested on Odroid XU4.
Signed-off-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add description of Dynamic Memory Controller and PPMU counters to
Exynos5422 and Odroid XU3/XU4/HC1 boards. They are used by
exynos5422-dmc driver. There is a definition of the memory chip, which
is then used during calculation of timings for each OPP.
The algorithm in the driver needs these two sets to bound the timings.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
XU3 family
The datasheet of S2MPS11 PMIC is slightly non-consistent in buck[78]
voltage regulators values.
1. The voltage tables for configuring their registers mention range of
voltages: 0.750 V to 3.55 V,
2. The constrains in electrical specifications say output voltage range
to be different (buck7: 1.2 V to 1.5 V, buck8: 1.8 V to 2.1 V).
Adjust the ranges to match the electrical specifications to stay on the
safe side. Also change the name of regulators to match reality. Anyway
these regulators stay at default value so this should not have effect.
Reported-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
family
Add the PMIC regulator suspend configuration to entire Odroid
XU3/XU4/HC1 family of boards to reduce power usage during suspend. The
configuration is based on vendor (Hardkernel) reference kernel with
additional buck9 suspend configuration (for USB hub suspend and proper
reset).
Energy consumption measurements from Marek Szyprowski during suspend to
RAM:
- all at 5 V power supply,
- before: next-20190620,
- after: next-20190620 + this patch + suspend configuration for s2mps11
regulator driver,
Board | before [mA] | after [mA] |
Odroid HC1 | 120 | 7-10 |
Odroid XU4, sdcard | 88 | 6-9 |
Odroid XU4, eMMC | 100 | 6-9 |
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
|
|
The eMMC memory on Odroid XU3/XU4 boards is supplied by two regulators
LDO18 and buck10 (and LDO13 for the host interface).
However the Odroid HC1 board does not have eMMC connector so this
regulator does not have to be always on.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The maximum voltage value for buck8 regulator on Odroid XU3/XU4 boards is
set too low. Increase it to the 2000mV as specified on the board schematic.
So far the board worked fine, because of the bug in the PMIC driver, which
used incorrect step value for that regulator. It interpreted the voltage
value set by the bootloader as 1225mV and kept it unchanged. The regulator
driver has been however fixed recently in the commit 56b5d4ea778c
("regulator: s2mps11: Fix steps for buck7, buck8 and LDO35"), what results
in reading the proper buck8 value and forcing it to 1500mV on boot. This
is not enough for proper board operation and results in eMMC errors during
heavy IO traffic. Increasing maximum voltage value for buck8 restores
original driver behavior and fixes eMMC issues.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 86a2d2ac5e5d ("ARM: dts: Add dts file for Odroid XU3 board")
Fixes: 56b5d4ea778c ("regulator: s2mps11: Fix steps for buck7, buck8 and LDO35")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Odroid HC1 uses the exynos5422-odroid-core.dtsi file as a base. All
other Exynos5422 Odroids use the "common". The ADC node was defined
only in the latter.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
There are two common DTSI files for Exynos5422 Odroid XU3 family of
boards. One is shared between all of them (XU3, XU3-Lite, XU4 and HC1)
and the second skips HC1. Document this in the files.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
XU3/XU4/HC1
Add SD card write-protect pin configuration to be sure that it will be
properly pulled down to indicate write access.
Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
XU3/XU4/HC1
Set the SD max-frequency to 200MHz for optimal performance on Odroid
XU3/XU4/HC1 family of boards.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
From Odroid XU3/XU4/HC1 schematics the LDO13 regulator for SD2, can be
set on 1.8V or 2.8V so the minimal value should be fixed to 1.8V. This
is necessary to support UHS-I tuning (otherwise card won't be detected
during boot).
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add support for UHS-I bus speed tuning for SDR50, DDR50 and SDR104 to
Odroid XU3/XU4/HC1 family boards.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The bindings for s2mps11/s5m8767 clocks driver require a compatible for
clocks node. Parent MFD sec-core driver will also use it when
instantiating children.
The compatible is not needed for proper working because device will be
anyway created by parent MFD device. Add it for correctness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The LDO28 is used only on Odroid XU3 for Display Port. Define it so DTS
will describe entire hardware.
Depending on bootloader behavior this might affect the Display Port
because none of drivers are enabling it. By default it is off in S2MPS11
PMIC reset values. However it could be enabled by bootloader so in such
case kernel will later disable it as unused regulator.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Disable unused PMIC regulators on Exynos5422 Odroid boards to reduce
energy used. According to schematics:
1. LDO12, LDO16 and LDO24 are not connected,
2. LDO26 is not used on Odroid HC1.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Define LDO14, LDO20-22, LDO25 and LOD29-38 unused regulators to
describe the hardware.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Define LDO2, LDO23 and LDO27 critical board regulators to describe the
hardware.
Suggested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find arch/arm/boot/dts -type f \( -iname "*.dts" -o -iname "*.dtsi" \) -exec sed -i \
-e "s/@\([0-9a-fA-FxX\.;:#]\+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 \
{/g" -e "s/@0\+\(.\+\) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace: https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve also a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[krzk: Rerun the command to include few more changes, adjust the commit msg]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Replace GPL v2.0 license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Looking at the schematic, LDO15 and LDO17 are tied as a power source of a
builtin network chipset. Correct voltage on LDO15 to 3.3V and the name
of LDO17 to "vdd_ldo17".
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Odroid HC1 board is based on Odroid XU4 board, but it has no HDMI,
no eMMC, no built-in USB3.0 hub, no extension port pins, and no GPIO
button. USB3.0 ports are used for built-in JMicron USB to SATA bridge
and Gigabit R8152 ethernet chips. HC1 uses only passive cooling.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
