| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Boards based on imx6qdl have duplicate memory nodes:
- One coming from the board device tree file: memory@
- One coming from the imx6qdl.dtsi file.
Fix the duplication by removing the memory node from
the imx6qdl.dtsi file and by adding 'device_type = "memory";'
in the board Device Tree.
Converted using the following command:
perl -p0777i -e 's/memory\@10000000 \{\n/memory\@10000000 \{\n\t\tdevice_type = \"memory\";\n/m' `find ./arch/arm/boot/dts -name "imx6*"``
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove unnecessary #address-cells/#size-cells to fix the following
DTC warnings:
arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@2400000/port@2: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@2400000/port@3: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@2800000/port@2: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@2800000/port@3: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree updates for 4.15" from Shawn Guo:
- New board support: i.MX51 ZII RDU1, i.MX53 GE Healthcare PPD, i.MX6
TX modules for MB7 from Ka-Ro Electronics, i.MX6 Wandboard revd1
variants, i.MX6 LWN DISPLAY5 board, Pistachio i.MX6Q board, i.MX6SX
Vining-2000 board.
- Use the 'vpcie-supply' property for PCIe device for boards
imx6qdl-sabresd, imx6q-novena and imx6q-cm-fx6.
- A series from Jagan Teki to update imx6qdl-icore board with audio,
touch and CAN support.
- Switch to nvmem for accessing OCOTP from tempmon for i.MX6SX and add
tempmon support for i.MX6UL.
- A bunch of patches from Lothar Waßmann updating Ka-Ro i.MX28, i.MX53
and i.MX6 TX modules.
- Fix DTC warnings in i.MX device trees, dropping leading zeros from
unit address, correcting display nodes notation and display port
names, fixing nodes with unit name and no reg property.
- Other random device updates for various board support.
* tag 'imx-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (63 commits)
ARM: dts: imx53-tx53: fix interrupt flags
ARM: dts: imx28-tx28: fix interrupt flags
ARM: dts: display5: Device tree description of LWN's DISPLAY5 board
ARM: dts: imx53-qsb-common: Fix 'led_gpio7_7@0' node with unit name and no reg property
ARM: dts: imx53-m53evk: Fix 'led_gpio@0' node with unit name and no reg property
ARM: dts: imx53: Fix 'usbphy@x' node with unit name and no reg property
ARM: dts: imx51-ts4800: Fix 'port@0' node with unit name and no reg property
ARM: dts: imx51-apf51dev: Fix 'backlight@bl1' node with unit name and no reg property
ARM: dts: imx: add ZII RDU1 board
ARM: dts: imx: add support for TX6 modules on MB7 baseboard
ARM: dts: imx: add support for TX6QP
ARM: dts: imx6-tx6: add a .dtsi file for the MB7 baseboard
ARM: dts: imx6-tx6: move display configuration to .dtsi file
ARM: dts: imx6-tx6: add support for I2C bus recovery
ARM: dts: imx6-tx6: convert to using simple-audio-card
ARM: dts: imx6-tx6: specify ethernet phy reset post-delay
ARM: dts: imx6-tx6: improve ethernet related pinctrl setup
ARM: dts: imx6-tx6: add trickle-charge config for DS1339
ARM: dts: imx6-tx6: remove obsolete ipu1 alias
ARM: dts: imx6-tx6: remove obsolete eeti,egalax_ts
...
[arnd: made sure we have no new leading zeroes in unit address during merge]
|
|
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The following build warnings are seen with W=1:
Warning (unit_address_vs_reg): Node /display@di0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /display@di1 has a unit name, but no reg property
Fix all these warnings by changing 'display@diX' to 'dispX'.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Declared as a regulator since the driver doesn't have a reset-gpios
property for this.
This ensures that the PHY is woken up, not depending on the state the
second stage bootloader leaves the pin.
This is a workaround until a proper mechanism is provided to reset such
devices like the pwrseq library [1] for instance.
[1] https://lkml.org/lkml/2017/2/10/779
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Adds the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
Both hang off the same i2c2 bus, so they require different (and non-
default) i2c slave addresses.
The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.
The OV5640 connects to the input port on the MIPI CSI-2 receiver on
mipi_csi.
The OV5642 node is disabled temporarily while the subdev driver is
cleaned up and submitted later.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is a pin conflict with GPIO_6. This pin functions as a power
input pin to the OV5642 camera sensor, but ENET uses it as the h/w
workaround for erratum ERR006687, to wake-up the ARM cores on normal
RX and TX packet done events. So we need to remove the h/w workaround
to support the OV5642. The result is that the CPUidle driver will no
longer allow entering the deep idle states on the sabrelite.
This is a partial revert of
commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
interrupt.")
commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
for ERR006687")
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The license text has been mangled at some point then copy pasted across
multiple files. Restore it to what it should be.
Note that this is not intended as a license change.
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit b36581df7e78 ("spi: imx: Using existing properties for
chipselects") the device tree property 'fsl,spi-num-chipselects' is
unused and it is already marked as obsolete in device tree binding
documentation. Remove the property from the existing DTS files to
avoid its reoccurence on copying.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The bus format is therefore retrieved from the connected panel
information.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Also aligning the panel nodes name across all platforms.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Several dts files set a bit in the SPEED field for pads
RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there
doesn't have an effect and the bit reads as zero.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the DT property to all boards that have the hardware workaround
for erratum ERR006687 present. This allows the CPUidle driver to use
the deep idle states, even if the FEC is active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Using "IMX6QDL_CLK_CKO" for the clock is easier to read instead of
the hardcoded clock number.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" and "enable-sdio-wakeup" boolean
property to enable the wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds support for the 7" LCD display available for Sabrelite:
http://boundarydevices.com/product/7-800x480-display/
Also add label to backlight_lcd and connect it to the panel.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Starting with commit 8947e396a829 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
|
|
Currently it is not possible to have HDMI and LVDS working simultaneously,
because both ports try to use PLL5.
Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
driven from independent sources.
With this change the LDB pixel clock goes to 68.57 MHz, which is still
within the valid range for the HSD100PXN1 LVDS panel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Also add label for backlight_lvds and connect it to the LVDS display.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The DAI mode is and should be configured by the sound card driver as
codec and ssi have to be in the right modes to communicate with each
other. It is possible to operate the ssi unit or the codec in master mode,
sometimes even on the same board in different configurations.
With the latest changes in the fsl-ssi driver, the 'fsl,mode' property
is only handled as a fallback property. If the sound card sets the DAI
mode correctly, this fallback configuration is dropped.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This adds the stdout-path property to various i.MX boards. Values
of the property have been taken from barebox, so they should be
correct. Also, the older linux,stdout-path property is converted
to stdout-path.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This works around a hardware bug.
From "Chip Errata for the i.MX 6Dual/6Quad"
ERR006687 ENET: Only the ENET wake-up interrupt request can wake the
system from Wait mode.
The ENET block generates many interrupts. Only one of these interrupt lines
is connected to the General Power Controller (GPC) block, but a logical OR
of all of the ENET interrupts is connected to the General Interrupt Controller
(GIC). When the system enters Wait mode, a normal RX Done or TX Done does not
wake up the system because the GPC cannot see this interrupt. This impacts
performance of the ENET block because its interrupts are serviced only when
the chip exits Wait mode due to an interrupt from some other wake-up source.
Before this patch, ping times of a Sabre Lite board are quite
random:
ping 192.168.0.13 -i.5 -c5
PING 192.168.0.13 (192.168.0.13) 56(84) bytes of data.
64 bytes from 192.168.0.13: icmp_req=1 ttl=64 time=15.7 ms
64 bytes from 192.168.0.13: icmp_req=2 ttl=64 time=14.4 ms
64 bytes from 192.168.0.13: icmp_req=3 ttl=64 time=13.4 ms
64 bytes from 192.168.0.13: icmp_req=4 ttl=64 time=12.4 ms
64 bytes from 192.168.0.13: icmp_req=5 ttl=64 time=11.4 ms
=== 192.168.0.13 ping statistics ===
5 packets transmitted, 5 received, 0% packet loss, time 2004ms
rtt min/avg/max/mdev = 11.431/13.501/15.746/1.508 ms
____________________________________________________
After this patch:
ping 192.168.0.13 -i.5 -c5
PING 192.168.0.13 (192.168.0.13) 56(84) bytes of data.
64 bytes from 192.168.0.13: icmp_req=1 ttl=64 time=0.120 ms
64 bytes from 192.168.0.13: icmp_req=2 ttl=64 time=0.175 ms
64 bytes from 192.168.0.13: icmp_req=3 ttl=64 time=0.169 ms
64 bytes from 192.168.0.13: icmp_req=4 ttl=64 time=0.168 ms
64 bytes from 192.168.0.13: icmp_req=5 ttl=64 time=0.172 ms
=== 192.168.0.13 ping statistics ===
5 packets transmitted, 5 received, 0% packet loss, time 1999ms
rtt min/avg/max/mdev = 0.120/0.160/0.175/0.026 ms
____________________________________________________
Also, apply same change to imx6qdl-nitrogen6x.
This change may not be appropriate for all boards.
Sabre Lite uses GPIO6 as a power down output for a ov5642
camera. As this expansion board does not yet work with mainline,
this is not yet a conflict. It would be nice to have an alternative
fix for boards where this is a problem.
For example Sabre SD uses GPIO6 for I2C3_SDA. It also
has long ping times currently. But cannot use this fix
without giving up a touchscreen.
Its ping times are also random.
ping 192.168.0.19 -i.5 -c5
PING 192.168.0.19 (192.168.0.19) 56(84) bytes of data.
64 bytes from 192.168.0.19: icmp_req=1 ttl=64 time=16.0 ms
64 bytes from 192.168.0.19: icmp_req=2 ttl=64 time=15.4 ms
64 bytes from 192.168.0.19: icmp_req=3 ttl=64 time=14.4 ms
64 bytes from 192.168.0.19: icmp_req=4 ttl=64 time=13.4 ms
64 bytes from 192.168.0.19: icmp_req=5 ttl=64 time=12.4 ms
=== 192.168.0.19 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 2003ms
rtt min/avg/max/mdev = 12.451/14.369/16.057/1.316 ms
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Ranjani Vaidyanathan <ra5478@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Note that the fec driver code currently hard-codes an active-low
reset, regardless of the flags in the device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add power, menu, home, back, volume up, and volume down
buttons.
Also, apply same changes to imx6qdl-nitrogen6x.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
KEY_COL4 is over-current for usbotg on Sabre Lite.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
GPIO16 is used for I2C3, not ENET_REF_CLK.
Also, remove pull-ups from tx pins, and ENET_MDIO
which has an external pull-up.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Set the data delays to min, and clock delays to max
because the traces are equal length on pcb.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
add pwm1 for lcd backlight
add pwm4 for lvds backlight
add pwm3 for ov5640 mipi clock
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Explicitly sets the pad GPIO_0 (sys_mclk) to 0x030b0.
Before this patch, it has the value 0x130b0 if using mainline u-boot.
So this patch also removes hysteresis. The 100k pulldown remains so
that a disabled clock will be low.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch moves pin EIM_D23 (phy reset) from pinctrl_hog to pinctrl_enet.
It also explicitly sets the pad to 0x000b0.
Before this patch, it has the value 0x1b0b0 if using mainline u-boot.
So this patch also removes hysteresis and a 100K pullup since the pad
is always an output.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch moves pin EIM_D22(power enable) from pinctrl_hog to pinctrl_usbotg.
It also explicitly sets the pad to 0x000b0, which is also the value
that it has before this patch if using mainline u-boot.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch moves pin EIM_D19 (CS) from pinctrl_hog to pinctrl_ecspi1.
It also explicitly sets the pad to 0x000b1.
Before this patch, it has the value 0x100b1 if using mainline u-boot.
So this patch also removes hysteresis since the pad is always an output.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch moves pin SD3_DAT5/4 (CD/WP) from pinctrl_hog to pinctrl_usdhc3.
It also explicitly sets the pad SD3_DAT5 to 0x1b0b0, which is also the value
that it has before this patch if using mainline u-boot.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch moves pin NANDF_D6 (CD) from pinctrl_hog to pinctrl_usdhc4.
It also explicitly sets the pad to 0x1b0b0, which is also the value
that it has before this patch if using mainline u-boot.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
On Sabre Lite usdhc4 is a micro sd slot, which has no
write protect.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Uart1 is available on Sabre Lite.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This makes the structure of Sabre Lite board files the same
as Sabre SD board files so that they are easier to compare.
By this, I mean that the majority of the file imx6q-sabrelite.dts
is moved to imx6qdl-sabrelite.dtsi so that both imx6q-sabrelite.dts
and imx6dl-sabrelite.dts can include it.
Now Sabre Lite has support for Dual Lite/Solo
processors.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
