Age | Commit message (Collapse) | Author | Files | Lines |
|
Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit 6d4cd041f0af ("net: phy: at803x: disable delay only for RGMII mode")
exposed an issue on imx DTS files using AR8031/AR8035 PHYs.
The end result is that the boards can no longer obtain an IP address
via UDHCP, for example.
Quoting Andrew Lunn:
"The problem here is, all the DTs were broken since day 0. However,
because the PHY driver was also broken, nobody noticed and it
worked. Now that the PHY driver has been fixed, all the bugs in the
DTs now become an issue"
To fix this problem, the phy-mode property needs to be "rgmii-id", which
has the following meaning as per
Documentation/devicetree/bindings/net/ethernet.txt:
"RGMII with internal RX and TX delays provided by the PHY, the MAC should
not add the RX or TX delays in this case)"
Tested on imx6-sabresd, imx6sx-sdb and imx7d-pico boards with
successfully restored networking.
Based on the initial submission from Steve Twiss for the
imx6qdl-sabresd.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Soeren Moch <smoch@web.de>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Adam Thomson <Adam.Thomson@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This extends the peripherals supported by the imx7d-pico.dtsi. It
adds:
- I2C2
- Flexcan (flexcan1 and flexcan2 ports)
- USDHC1
- UART (6 and 7 ports)
- PWM (4 ports)
- eCSPI3
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There are different models of WiFi being used in the SoM and the
handle name was too restrictive. This reworks it to a more generic and
meaningful name.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pass the "phy-reset-gpios" property in order to describe the GPIO
that performs the Ethernet PHY reset.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pass the USBOTG1_PWR pinctrl description in the USBOTG GPIO
controlled regulator.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
imx7d-pico-pi board contains:
- One SoM board (imx7d pico)
- One base board (pi).
In order to make it easier for adding support for other board variants,
move the commom SoM part to the imx7d-pico.dtsi file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently the memory size described in dts is 2GB, which is incorrect.
There are 512MB and 1GB versions of imx7d-pico boards, so remove
the hardcoded memory size and let the bootloader pass the correct
value to the kernel.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX fixes for 4.20, round 3:
- A couple of fixes on imx7d-pico and imx7d-nitrogen7 boards to correct
the description of the Wifi clock.
- Change SW2ISO count to get a safer ARM LDO ramp-up time, so that
different boards can be covered. This fixes the ARM LDO failure seen
on some customer boards.
|
|
Boards based on imx7 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx7s.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Wifi chip should be clocked by a 32kHz clock coming from i.MX7D
CLKO2 output pin, so describe the pinmux and clock hierarchy in the
device tree to allow the Wifi chip to be properly clocked.
Managed to successfully test Wifi with such change. Used the standard
nvram.txt file provided by TechNexion, which selects an external 32kHz
clock for the Wifi chip by default.
Fixes: 99a52450c707 ("ARM: dts: imx7d-pico: Add Wifi support")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Separate the old imx7d-pico into cpu (imx7d-pico.dtsi) and baseboard
(imx7d-pico-pi.dts) dts so the same cpu dtsi can be used in different
baseboards variants.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|