Age | Commit message (Collapse) | Author | Files | Lines |
|
On those boards, as stated in schematics files, the regulator used for IOs
is VDD. It was wrongly set to v3v3.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
On STM32MP1 DK1, DK2, ED1 and EV1 boards, there is only a micro SD socket.
This is also the case on Avenger board.
They don't support the Write Protect pin.
The disable-wp is then added in the SD-cards sdmmc1 nodes.
This avoids executing some code and a warning during driver probe.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The broken-cd properties are replaced with cd-gpios, with the correct
GPIO to detect the card insertion. The GPIO lines require a pull-up.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Remove unused properties from stpmic node.
The issues have been detected by running dtbs_check.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add the sleep state pinctrl entry for the i2c4 node
of the stm32mp157c-ed1 board.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
On this board, the I2C4 bus has only a single slave (pmic) which
supports I2C Fast Mode hence setting bus frequency to 400 KHz.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Now that st,stm32mp15-hsotg is used, dual role is supported. ID pin is
managed to detect the current role.
On stm32mp157c-ev1, Host mode requires a vbus-supply property. Charge pump
for vbus is provided by PMIC VBUS_OTG.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This commit adds security (cryp1) IP to stm32mp157c ED1 board by including
stm32mp15xc.dtsi file.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
STM32MP151 and STM32MP153 were not explicitly supported through
stm32mp157c.dts. This commit adds dedicated files to support all STM32MP15
SOCs family.
The differences between those SOCs are:
-STM32MP151 [1]: common file.
-STM32MP153 [2]: STM32MP151 + CANs + a second CortexA7-CPU.
-STM32MP157 [3]: STM32MP153 + DSI + GPU.
[1] https://www.st.com/resource/en/reference_manual/dm00366349.pdf
[2] https://www.st.com/resource/en/reference_manual/dm00366355.pdf
[3] https://www.st.com/resource/en/reference_manual/dm00327659.pdf
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
In order to cover the STM32MP15 SOCs family this commit updates pinctrl
file names (group definition and packages files).
This family includes: STM32MP151, STM32MP153 and STM32MP157.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add ADC support to stm32mp157c-ed1 board.
Following ADC signals are dedicated for analog and routed to connectors:
- ADC1/2 in0 (ANA0)
- ADC1/2 in1 (ANA1)
- ADC1 in6 (PF12)
Configure ADC1 with these signals. But keep it disabled by default, so
PF12 can be used as gpio by default.
Add VDD and VDDA supplies to ADC on stm32mp157c-ed1 board. This allows to
get full ADC analog performances in case VDDA is below 2.7V (not the case
by default).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
On STM32MP157C-ED1, the eMMC is connected on instance 2 of SDMMC
peripheral. The sdmmc2 node is then added in the board DT file, as well as
the pins nodes in the pinctrl file.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Active discharge is a uint32 not a boolean.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Minimal value is the value set during boot or before suspend.
We must ensure that the value is a functional value to boot.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds support of STM32 PWR regulators on
stm32mp157c. This replace dummy fixed regulators on
stm32mp157c-ed1 and stm32mp157c-dk2.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
stm32mp157c-ed1 board has digital-to-analog converter signals routed
to JP11 and JP10 jumpers (e.g. PA4/PA5).
It's easier then to configure them both. But keep them disabled by default,
so the pins are kept in their initial state to lower power consumption.
This way they can also be used as GPIO.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This commit fixes regulator-sd_switch node in order to be compliant to
DT validation schema.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable m4 coprocessor for STM32MP157c-ed1 board.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Declare reserved memories shared by the processors for STM32MP157c-ed1
board.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable Vivante GPU driver for stm32mp157c-ed1 board.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Four packages exist for stm32mp157 die. As ball-out is different between
them, this patch covers those differences by creating dedicated pinctrl
dtsi files. Each dtsi pinctrl package file describes the package ball-out
through gpio-ranges.
stm32mp157a-dk1 / dk2 boards embed a STM32MP_PKG_AC (TFBGA361 (12*12))
package.
stm32mp157c-ed1 / ev1 boards embed a STM32MP_PKG_AA (LFBGA448 (18*18))
package.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds stpmic1 support on stm32mp157c ed1 board.
The STPMIC1 is a PMIC from STMicroelectronics. The STPMIC1 integrates 10
regulators, 3 power switches, a watchdog and an input for a power on key.
The DMAs are disabled because the PMIC generates a very few traffic and
DMA channels may lack for other usage.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable STM32 IPCC mailbox driver for STM32MP157c-ed1 board.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds sdmmc1 support on stm32mp157c ed1 board.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.1, round 1
Highlights:
----------
MPU part:
-Enable Digital Thermal Sensor (dts) on stm32mp157c-ed1 (and so ev1).
MCU part:
-Add SPI support on stm32f429 SOC (4 SPIs instances).
* tag 'stm32-dt-for-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Enable thermal sensor support on STM32MP157c-ed1
ARM: dts: stm32: add SPI support on STM32F429 SoC
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable STM32 Digital Thermal Sensor (dts) driver for STM32MP157c-ed1 board.
Signed-off-by: David Hernandez Sanchez <david.hernandezsanchez@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61f1 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.
The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Spare dmas when using timer6 on stm32mp157c-ed1.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch activates independent watchdog support for
stm32mp157c board.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Nodes should be ordered in alphabetic order.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable RTC (Real Time Clock) on stm32mp157c-ed1 board.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Fix DTC warnings for stm32mp157:
Warning (unit_address_vs_reg): /soc/pin-controller: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /soc/pin-controller/uart4@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/pin-controller-z: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
USBPHYC ports require 3 supplies: 3v3, 1v1 and 1v8.
This patch adds the corresponding properties to usbphyc ports on
stm32mp157c-ed1 board.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add I2C4 support for STM32MP157C evaluation daughter.
Required for PMIC.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable stm32-hwrng for ed1 and ev1 boards
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable timer 6 on stm32mp157c-ed1 that can serve as trigger for
ADC for instance.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add support of stm32mp157c evaluation board (part number: STM32MP157C-EV1)
split in 2 elements:
-Daughter board (part number: STM32MP157C-ED1)
which includes CPU, memory and power supply
-Mother board (part number: STM32MP157C-EM1)
which includes external peripherals (like display, camera,...)
and extension connectors.
The daughter board can run alone, this is why the device tree files
are split in two layers, for the complete evaluation board (ev1)
and for the daughter board alone (ed1).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|