Age | Commit message (Collapse) | Author | Files | Lines |
|
The DWMAC binding never supported having the Ethernet PHY node as a
direct child to the controller, nor did it support the "phy" property
as a way to specify which Ethernet PHY to use. What seemed to work
was simply the implementation ignoring the "phy" property and instead
probing all addresses on the MDIO bus and using the first available
one.
The recent switch from "phy" to "phy-handle" breaks the assumptions
of the implementation, and does not match what the binding requires.
The binding requires that if an MDIO bus is described, it shall be
a sub-node with the "snps,dwmac-mdio" compatible string.
Add a device node for the MDIO bus, and move the Ethernet PHY node
under it. Also fix up the #address-cells and #size-cells properties
where needed.
Fixes: de332de26d19 ("ARM: dts: sunxi: Switch from phy to phy-handle")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The phy device tree property has been deprecated in favor of phy-handle,
let's replace it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Our display engine endpoints trigger some DTC warnings due to the fact that
we're having a single endpoint that doesn't need any reg property, and
since we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Fix those
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Cubieboard4 has a Realtek RTL8211E ethernet PHY which uses RGMII to
talk to the MAC. The PHY is powered by 2 regulators: cldo1 for the PHY's
core logic and gpio1-ldo for I/O. The latter also powers the SoC side
pins. As there is no binding to model a second regulator supply for the
PHY, it is omitted. It is however properly modeled for the PIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Cubieboard 4 has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard:
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
* tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus
ARM: dts: sun8i-h3: Add Mali node
ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards
ARM: dts: sun8i: h3: Enable HDMI output on H3 boards
ARM: dts: sunxi: h3/h5: Add HDMI pipeline
ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node
ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi
ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl
ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
ARM: dts: nanopi-neo-air: Add WiFi / eMMC
|
|
The Cubieboard4 has a dumb VGA DAC connected to the output of LCD0,
providing VGA output through the onboard VGA connector. The DDC lines
are connected to i2c3.
The VGA DAC is a GM7123, which is compatible with Analog Devices'
ADV7123, except it only takes 3.3V power, and has a lower standby power
consumption. The datasheet found online lists "Chengdu GoldTel Electronical
Technology Co., Ltd." as its designer. The company changed its name in
2014 to "Chengdu Corpro Technology Co., Ltd.". Their website lists similar
ICs, but not actually the GM7123.
Enable the display pipeline with the VGA DAC and connector, and i2c3
for DDC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Some boards have had node names with underscores. Remove them in favour of
hyphens in order to reduce the DTC warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The board has an external pull-up on the card-detect signal, so there's no
need to add another one.
This also removes a DTC warning.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Our pinctrl node names were containing unit-adresses without a reg
property, resulting in a warning. Change the names for our new convention.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A80 boards still define some GPIO pinctrl nodes that are not really
useful, and redundant with the muxing already happening on gpio_request.
Let's remove those nodes. This will also remove DTC warnings.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).
Remove these properties to make it obvious that we do not set anything in
such a case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP809's SW (switch) regulator is unused on the Cubieboard 4.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The 32.768 kHz clock inside the A80 SoC is fed from an external source,
typically the AC100 RTC module.
Make the osc32k placeholder a fixed-factor clock so board dts files can
specify its source.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Move the &pio node below the mmc nodes for proper ordering by name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
sunxi-common-regulators.dtsi provided dummy regulators vcc3v0, vcc3v3,
vcc5v0. 3.0V/3.3V and 5.0V are commonly used voltages in Allwinner
devices. These dummy regulators provide a stand-in when bindings that
require one, but the real regulator is not supported yet.
Since these are no longer needed, we can drop the include file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is connected
to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
mmc2 has a special pin for eMMC hardware reset, which is controllable
from the controller. Add the "mmc-cap-hw-reset" property to denote that
this controller supports this function, and the pins are actually used.
Also increase the signal drive strength for mmc2 pins, for HS-DDR mode
support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Reduced Serial Bus (RSB) controller is used to talk to the 3
companion ICs (2 PMICs, 1 RTC/codec IC) on the board.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Cubieboard4 has a consumer IR receiver. Enable it in the DT.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Cubieboard4 has 2 controllable LEDs, 1 red and 1 green.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add a Cubietech Cubieboard4 device tree and instruct make to build it. This
device tree has been derived from the sun9i-a80-optimus.dts as they are very
similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM
definitions will need to be updated in the future.
[1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdf
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|