| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX arm64 device tree for 6.9:
- New board support: Apalis eval v1.2 carrier board, Variscite
VAR-SOM-MX93, phyBOARD-Segin-i.MX93.
- A series from Adam Ford to enable bluetooth, configure multiple queues
on eqos, remove unnecessary clock configuration for i.MX8 Beacon boards.
- Several changesets from Alexander Stein to add i.MX8DXP support, enable
audio and GPU for i.MX8QXP, re-parent MEDIA_MIPI_PHY1_REF clock for
i.MX8MP, and improve MBA8xx board description.
- A few dt-schema fixes from Fabio Estevam for i.MX8MM and i.MX93 devices.
- A bunch of changes from Frank Li to improve i.MX8QM and i.MX8DXL
support, correcting edma3 power-domains and interrupt numbers, adding
I2C, FlexCAN and SMMU devices, etc.
- A series from Frieder Schrempf to improve imx8mm-kontron board
descriptions, disabling pulls, fixing up RTC device, adding EEPROM,
and refactoring OSM-S module, etc.
- A set of Data Modul i.MX8M Plus eDM SBC improvements from Marek Vasut.
- A series from Shengjiu Wang to add PDM micphone and SPDIF sound card
support for imx8mm-evk board.
- A series of imx8mm-venice boards improvement from Tim Harvey to add
TPM device, fix USB OTG VBUS etc.
- Other small and random improvements on various boards.
* tag 'imx-dt64-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (77 commits)
arm64: dts: imx8mm-kontron-bl-osm-s: Fix Ethernet PHY compatible
arm64: dts: imx8-apalis-v1.1: Remove reset-names from ethernet-phy
arm64: dts: imx8mp-evk: Fix hdmi@3d node
arm64: dts: imx93-var-som: Remove phy-supply from eqos
arm64: dts: imx8mp-phyboard-pollux: Disable pull-up for CD GPIO
arm64: dts: imx8mp-phyboard-pollux: Reduce drive strength for eqos tx lines
arm64: dts: imx8mp-phyboard-pollux: Set debug uart muxing to 0x140
arm64: dts: imx8mp-phyboard-pollux: Add and update rtc devicetree node
arm64: dts: imx8mm-evk: Add spdif sound card support
arm64: dts: mba8xx: Add missing #interrupt-cells
arm64: dts: imx8mp: Set SPI NOR to max 40 MHz on Data Modul i.MX8M Plus eDM SBC
arm64: dts: imx8mn: tqma8mqnl-mba8mx: Add USB DR overlay
arm64: dts: imx8mq: tqma8mq-mba8mx: Add missing USB vbus supply
arm64: dts: freescale: imx8mm/imx8mq: mba8mx: Use PCIe clock generator
arm64: dts: imx8mn-beacon: Remove unnecessary clock configuration
arm64: dts: imx8mn: Slow default video_pll clock rate
arm64: dts: imx8mp-beacon: Configure multiple queues on eqos
arm64: dts: imx8mp-beacon: Enable Bluetooth
arm64: dts: freescale: minor whitespace cleanup
arm64: dts: lx2160a: Fix DTS for full PL011 UART
...
Link: https://lore.kernel.org/r/20240226034147.233993-4-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The SPI NOR bus routing on this board cannot go above 50 MHz,
set the clock frequency to maximum of 40 MHz to be within a
safe margin. Remove the comment as well.
Fixes: 562d222f23f0 ("arm64: dts: imx8mp: Add support for Data Modul i.MX8M Plus eDM SBC")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add SAI I2S and audio bindings to Data Modul i.MX8M Plus eDM SBC.
The SGTL5000 is attached to SAI3, however the SGTL5000 codec MCLK
must be supplied even if the SAI3 is not in use and is controlled
separately by the codec. The MCLK is also used to drive the codec
I2C block, so without MCLK, I2C access to the codec would not be
possible.
To provide such flexible MCLK control, use PWM4 with period 1 and
duty cycle 50% as 12 MHz clock source, as there is no direct way
to route MX8MP CCM clock to the MCLK pin. Use codec as bitclock
and frame clock master, so that the SGTL5000 PLL can be used to
generate derived clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable PCIe support on Data Modul i.MX8M Plus eDM SBC.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
UART4 is used as CM7 coprocessor debug UART and may not be accessible from
Linux in case it is protected by RDC. The RDC protection is set up by the
platform firmware. UART4 is not used on this platform by Linux. Disable
UART4 by default to prevent boot hangs, which occur when the RDC protection
is in place.
Fixes: 562d222f23f0 ("arm64: dts: imx8mp: Add support for Data Modul i.MX8M Plus eDM SBC")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX8M Plus eDM SBC
Describe VDD_ARM (BUCK2) run and standby voltage in DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for Data Modul i.MX8M Plus eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
