Age | Commit message (Collapse) | Author | Files | Lines |
|
Since commit 65ac79e18120 ("net: dsa: microchip: add the phylink
get_caps") the phy-mode must be set otherwise the switch driver will
assume "NA" mode and invalidate the port.
Fixes: 7899eb6cb15d ("arm64: dts: imx: Add i.MX8M Plus Gateworks gw7400 dts support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The CPU uplink port on the KSZ9477 is P5 not P6 - fix this.
Fixes: 7899eb6cb15d ("arm64: dts: imx: Add i.MX8M Plus Gateworks gw7400 dts support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The CAN STBY poarlity is active-low. Specify it as such by removing the
'enable-active-high' property and updating the gpio property.
Fixes: 7899eb6cb15d ("arm64: dts: imx: Add i.MX8M Plus Gateworks gw7400 dts support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
imx8mm-tqma8mqml.dtsi has PCIe support, so it should include
<dt-bindings/phy/phy-imx8-pcie.h>.
Otherwise, there are build errors when this SoM dtsi is included
on customers' carrier boards.
While at it, remove the PCI header from imx8mm-tqma8mqml-mba8mx.dts,
which is now unneeded.
Fixes: 1d84283101fc ("arm64: dts: tqma8mqml: add PCIe support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Although the RTC is on the module, the RTC_EVENT# signal is connected
on the mainboard. Already set by bootloader, but make it explicit in Linux
as well.
Fixes: 418d1d840e42 ("arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently, we limited the voltages from the PMIC very strictly. This
causes an issue with one Toradex SKU that uses a consumer-grade chip
that is capable of going up to 1.8GHz at 1.00V.
Extend the ranges to min/max values of the SoC operating ranges (table
10) in the datasheet. Detailed explanation as follows:
BUCK2:
- As already described above, the SKU with the consumer-grade chip
needs a voltage of at least 1.00V. 1.05V is chosen now as this is
listed as the maximum. Both industrial and consumer-grade chips have
an absolute maximum rating of 1.15V which makes it still safe to put
1.05V
- Lower the regulator-min value to the smallest value allowed from the
Quad-A53, 1.2GHz version of the SoC
BUCK3:
- This regulator is used for SoC input voltages VDD_GPU, VDD_VPU and
VDD_DRAM.
- Use the smallest value of these three inputs as the regulator-min
- Use the largest value of these three inputs as the regulator-max
LDO2:
- This LDO is used for VDD_SNVS_0P8 SoC input voltage. As this has a
single nominal input voltage just put this in the middle of 0.8V.
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding file clock/imx8ulp-pcc-clock.yaml indicates '#reset-cells'
is a required property, add it.
Fixes: fe6291e96313 ("arm64: dts: imx8ulp: Add the basic dtsi file for imx8ulp")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
They were in wrong order, so fix it by switching them.
Fixes: 418d1d840e42 ("arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PGC (power gating controller) already handles the reset for the
GPUMIX power domain. By specifying it within the device tree the reset
it issued a 2nd time. This confuses the hardware during power up and
sporadically hangs the SoC. Fix this by removing the reset property and
let the hardware handle the reset.
Fixes: 9a0f3b157e22e ("arm64: dts: imx8mn: Enable GPU")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The CPLD_Dn GPIO assignment between SoM and CPLD has now been clarified
in schematic and the assignment is reversed. Update the DT to match the
hardware.
Fixes: 510c527b4ff57 ("arm64: dts: imx8mm: Add i.MX8M Mini Toradex Verdin based Menlo board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix reset GPIO polarity in-line with the following commit feedaacdadfc
("Input: atmel_mxt_ts - fix up inverted RESET handler").
Fixes: a39ed23bdf6e ("arm64: dts: freescale: add initial support for verdin imx8m plus")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix reset GPIO polarity in-line with the following commit feedaacdadfc
("Input: atmel_mxt_ts - fix up inverted RESET handler").
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix copy-paste error of the I2C5 bus recovery GPIO assignment,
the I2C5 GPIOs are on gpio3 instead of gpio5.
Fixes: 8d6712695bc8e ("arm64: dts: imx8mp: Add support for DH electronics i.MX8M Plus DHCOM and PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit 65ac79e18120 ("net: dsa: microchip: add the phylink
get_caps") the phy-mode must be set otherwise the switch driver will
assume "NA" mode and invalidate the port.
Fixes: 65ac79e18120 ("net: dsa: microchip: add the phylink get_caps")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Verdin iMX8M Mini System on Module does not have USB-ID signal
connected on Verdin USB_2 (usbotg2). On Verdin Development board this is
no problem, as we have connected a USB-Hub that is always connected.
However, if Verdin USB_2 is desired to be used as a single USB-Host port
the chipidea driver does not detect if a USB device is plugged into this
port, due to runtime pm shutting down the PHY.
Add the power-domain &pgc_otg2 to &usbphynop2 in order to detect
plugging events and enumerate the usb device.
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Lynx PCS integrated with ENETC port 0 does not support in-band
autoneg for the 2500base-x SERDES protocol, and prints errors from its
phylink methods. Furthermore, the AQR112 card used for these boards does
not expect in-band autoneg either. So delete the extraneous property.
Fixes: e426d63e752b ("arm64: dts: ls1028a-qds: add overlays for various serdes protocols")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This property was never needed, remove it. This also silences
dtbs_check warnings.
Fixes: b186b8b6e770 ("arm64: dts: freescale: add initial device tree for TQMa8Mx with i.MX8M")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The ECSPI1 is on I2C1/I2C2 pins of the SoC, update the pinmux accordingly.
Fixes: 8d6712695bc8e ("arm64: dts: imx8mp: Add support for DH electronics i.MX8M Plus DHCOM and PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The pad settings are missed, add them
Fixes: 7899eb6cb15d ("arm64: dts: imx: Add i.MX8M Plus Gateworks gw7400 dts support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Switch to level interrupt for mcp251xfd. This will make sure no
interrupts are lost.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update SPI CAN controller clock to match current hardware design.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking changes from Paolo Abeni:
"Core:
- Refactor the forward memory allocation to better cope with memory
pressure with many open sockets, moving from a per socket cache to
a per-CPU one
- Replace rwlocks with RCU for better fairness in ping, raw sockets
and IP multicast router.
- Network-side support for IO uring zero-copy send.
- A few skb drop reason improvements, including codegen the source
file with string mapping instead of using macro magic.
- Rename reference tracking helpers to a more consistent netdev_*
schema.
- Adapt u64_stats_t type to address load/store tearing issues.
- Refine debug helper usage to reduce the log noise caused by bots.
BPF:
- Improve socket map performance, avoiding skb cloning on read
operation.
- Add support for 64 bits enum, to match types exposed by kernel.
- Introduce support for sleepable uprobes program.
- Introduce support for enum textual representation in libbpf.
- New helpers to implement synproxy with eBPF/XDP.
- Improve loop performances, inlining indirect calls when possible.
- Removed all the deprecated libbpf APIs.
- Implement new eBPF-based LSM flavor.
- Add type match support, which allow accurate queries to the eBPF
used types.
- A few TCP congetsion control framework usability improvements.
- Add new infrastructure to manipulate CT entries via eBPF programs.
- Allow for livepatch (KLP) and BPF trampolines to attach to the same
kernel function.
Protocols:
- Introduce per network namespace lookup tables for unix sockets,
increasing scalability and reducing contention.
- Preparation work for Wi-Fi 7 Multi-Link Operation (MLO) support.
- Add support to forciby close TIME_WAIT TCP sockets via user-space
tools.
- Significant performance improvement for the TLS 1.3 receive path,
both for zero-copy and not-zero-copy.
- Support for changing the initial MTPCP subflow priority/backup
status
- Introduce virtually contingus buffers for sockets over RDMA, to
cope better with memory pressure.
- Extend CAN ethtool support with timestamping capabilities
- Refactor CAN build infrastructure to allow building only the needed
features.
Driver API:
- Remove devlink mutex to allow parallel commands on multiple links.
- Add support for pause stats in distributed switch.
- Implement devlink helpers to query and flash line cards.
- New helper for phy mode to register conversion.
New hardware / drivers:
- Ethernet DSA driver for the rockchip mt7531 on BPI-R2 Pro.
- Ethernet DSA driver for the Renesas RZ/N1 A5PSW switch.
- Ethernet DSA driver for the Microchip LAN937x switch.
- Ethernet PHY driver for the Aquantia AQR113C EPHY.
- CAN driver for the OBD-II ELM327 interface.
- CAN driver for RZ/N1 SJA1000 CAN controller.
- Bluetooth: Infineon CYW55572 Wi-Fi plus Bluetooth combo device.
Drivers:
- Intel Ethernet NICs:
- i40e: add support for vlan pruning
- i40e: add support for XDP framented packets
- ice: improved vlan offload support
- ice: add support for PPPoE offload
- Mellanox Ethernet (mlx5)
- refactor packet steering offload for performance and scalability
- extend support for TC offload
- refactor devlink code to clean-up the locking schema
- support stacked vlans for bridge offloads
- use TLS objects pool to improve connection rate
- Netronome Ethernet NICs (nfp):
- extend support for IPv6 fields mangling offload
- add support for vepa mode in HW bridge
- better support for virtio data path acceleration (VDPA)
- enable TSO by default
- Microsoft vNIC driver (mana)
- add support for XDP redirect
- Others Ethernet drivers:
- bonding: add per-port priority support
- microchip lan743x: extend phy support
- Fungible funeth: support UDP segmentation offload and XDP xmit
- Solarflare EF100: add support for virtual function representors
- MediaTek SoC: add XDP support
- Mellanox Ethernet/IB switch (mlxsw):
- dropped support for unreleased H/W (XM router).
- improved stats accuracy
- unified bridge model coversion improving scalability (parts 1-6)
- support for PTP in Spectrum-2 asics
- Broadcom PHYs
- add PTP support for BCM54210E
- add support for the BCM53128 internal PHY
- Marvell Ethernet switches (prestera):
- implement support for multicast forwarding offload
- Embedded Ethernet switches:
- refactor OcteonTx MAC filter for better scalability
- improve TC H/W offload for the Felix driver
- refactor the Microchip ksz8 and ksz9477 drivers to share the
probe code (parts 1, 2), add support for phylink mac
configuration
- Other WiFi:
- Microchip wilc1000: diable WEP support and enable WPA3
- Atheros ath10k: encapsulation offload support
Old code removal:
- Neterion vxge ethernet driver: this is untouched since more than 10 years"
* tag 'net-next-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1890 commits)
doc: sfp-phylink: Fix a broken reference
wireguard: selftests: support UML
wireguard: allowedips: don't corrupt stack when detecting overflow
wireguard: selftests: update config fragments
wireguard: ratelimiter: use hrtimer in selftest
net/mlx5e: xsk: Discard unaligned XSK frames on striding RQ
net: usb: ax88179_178a: Bind only to vendor-specific interface
selftests: net: fix IOAM test skip return code
net: usb: make USB_RTL8153_ECM non user configurable
net: marvell: prestera: remove reduntant code
octeontx2-pf: Reduce minimum mtu size to 60
net: devlink: Fix missing mutex_unlock() call
net/tls: Remove redundant workqueue flush before destroy
net: txgbe: Fix an error handling path in txgbe_probe()
net: dsa: Fix spelling mistakes and cleanup code
Documentation: devlink: add add devlink-selftests to the table of contents
dccp: put dccp_qpolicy_full() and dccp_qpolicy_push() in the same lock
net: ionic: fix error check for vlan flags in ionic_set_nic_features()
net: ice: fix error NETIF_F_HW_VLAN_CTAG_FILTER check in ice_vsi_sync_fltr()
nfp: flower: add support for tunnel offload without key ID
...
|
|
Pull ARM DT updates from Arnd Bergmann:
"As usual, the bulk of the changes for the SoC tree are devicetree file
updates, and most of these changes are for 64-bit embedded machines.
As before, there are a ton of style cleanups, and additional hardware
support for existing machines.
Looking only at the new SoC, the notable additions are:
- A whole family of Broadcom broadband SoCs, both 32-bit and 64-bit:
BCM63178, BCM63158, BCM4912, BCM6858, BCM6878, BCM6846, BCM63146,
BCM6856, BCM6855, BCM6756, BCM63148, and BCM6813. Each SoC comes
with a corresponding reference board.
- The new NXP i.MX93 SoC, the follow-up to the popular i.MX6 and
i.MX8 embedded SoCs, now using Cortex-A55 cores and the Ethos-U65
NPU.
- Qualcomm Snapdragon 8cx Gen3 (SC8280XP), the current high end of
Arm based Laptop SoCs, and its automotive cousin, the SA8540P. The
SC8280XP is used in the Lenovo Thinkpad X13s laptop that also gets
added here in addition to the reference boards.
- Allwinner H616, a newer version of the H6 SoC, targeted at
Set-top-box applications. It comes with dts files for the Orange Pi
zero2 single-board computer and the X96 Mate set-top-box
- Marvell Prestera 98DX2530 (AlleyCat5), a network switch chip in the
Armada SoC family based on the Cortex-A55 core.
New machines based on previously supported SoCs include:
- Several new machines on NXP i.MX platforms: multiple Toradex
Colibri boards using the "Iris" and "Ixora" carriers, DH
electronics i.MX8M Plus DHCOM and PDK2, TQ-Systems TQMa8MPQL, and
phytech phyBOARD-Polis-i.MX8MM.
- Google Chameleon v3 FPGA board based on Intel Arria10 and Stratix
10 Software Virtual platform, both in the SoCFPGA platform.
- Two new wireless devices based on Broadcom SoCs: The Asus GT-AX6000
Router and the Cisco Meraki MR26 access point
- Improved Chromebook support for both the Mediatek and Qualcomm SoC
families brought added machines: Acer Chromebook 514 (MT8192), Acer
Chromebook Spin 513 (MT8195) and a couple of SC7180 based machines
including the Lenovo IdeaPad Chromebook Duet 3.
- Xiaomi Mi Mix2s, LG G7 and LG V35 are mobile phones based on
Qualcomm SDM845, while Mi 5s Plus is based on MSM8996.
- Finally, there are a few development board on other chips: PCB8309
(Microchip lan966x), Radxa Rock Pi S (Rockchips RK3308) DH DRC
Compact (ST STM32MP1) and Inforce IFC6560 (Qualcomm SDM660)"
* tag 'arm-dt-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (829 commits)
dt-bindings: soc: bcm: use absolute path to other schema
dt-bindings: soc: bcm: drop quotes when not needed
dt-bindings: soc: microchip: use absolute path to other schema
dt-bindings: soc: microchip: drop quotes when not needed
ARM: dts: lan966x: keep lan966 entries alphabetically sorted
ARM: dts: lan966x: add support for pcb8309
dt-bindings: arm: at91: add lan966 pcb8309 board
ARM: dts: lan966x: Enable network driver on pcb8291
ARM: dts: lan966x: Disable can0 on pcb8291
ARM: dts: lan966x: Add gpio-restart
dt-bindings: arm: aspeed: add Aspeed Evaluation boards
arm64: dts: qcom: Add support for Xiaomi Mi Mix2s
dt-bindings: arm: qcom: Add Xiaomi Mi Mix2s bindings
dt-bindings: arm: qcom: Document lg,judyln and lg,judyp devices
dt-bindings: arm: qcom: add missing SM6350 board compatibles
dt-bindings: arm: qcom: add missing SM6125 board compatibles
dt-bindings: arm: qcom: add missing SDM845 board compatibles
dt-bindings: arm: qcom: add missing SDM636 board compatibles
dt-bindings: arm: qcom: add missing SDM630 board compatibles
dt-bindings: arm: qcom: add missing QCS404 board compatibles
...
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rename the 'mod-def0-gpio' property to 'mod-def0-gpios' so that we use
the preferred -gpios suffix. Also, with this change the dtb_check will
not complain when trying to verify the DTS against the sff,sfp.yaml
binding.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree update for 5.20:
- Add device tree support for i.MX93 SoC.
- New board device tree: TQMa8MPQL, DH electronics i.MX8M Plus DHCOM and
PDK2, i.MX93 11x11 EVK, phyBOARD-Polis-i.MX8MM.
- A series from Abel Vesa and Viorel Suman to fix i.MX8QXP device tree
to comply with DT schema.
- Disable job ring 0 device for i.MX8MM to avoid caam_jr probe error, due
to that JR0 reservation is done in both upstream (v2.7) and downstream
(NXP lf_v2.4) TF-A.
- A series from Krzysztof Kozlowski to align gpio-key and LED node names
with dtschema.
- Add SNVS LPGPR device for i.MX8MM so that some preserving registers
becomes available as NVMEM.
- Add NoC device support for i.MX8MP SoC.
- A couple of changes from Sean Anderson to add SFP node for TA devices
for LayerScape SoCs.
- A series from Shengjiu Wang to enable bt-sco sound card support for
NXP i.MX8M EVK boards.
- Other small and random board updates.
* tag 'imx-dt64-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (33 commits)
arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP
arm64: dts: freescale: imx8qxp: Fix the keys node name
arm64: dts: freescale: imx8: Fix the system-controller node name
arm64: dts: freescale: imx8qxp: Fix the ocotp node name
arm64: dts: freescale: imx8qxp: Add fallback compatible for clock controller
arm64: dts: freescale: imx8: Fix power controller name
arm64: dts: freescale: imx8qxp: Remove unnecessary clock related entries
arm64: dts: imx8mp: add NoC node
arm64: dts: Add SFP node for TA 3.0 devices
arm64: dts: layerscape: Add SFP node for TA 2.1 devices
arm64: dts: freescale: Add phyBOARD-Polis-i.MX8MM support
arm64: dts: imx8m{m,p}-verdin: use IT temperatures
arm64: dts: imx8mn-evk: add bt-sco sound card support
arm64: dts: imx8mq-evk: add bt-sco sound card support
arm64: dts: imx8mm-evk: add bt-sco sound card support
arm64: freescale/imx8mp-evk.dts: reorder nodes alphabetically
arm64: dts: imx8mq: Pass a label to the AIPS nodes
arm64: dts: imx8m: Pass a label to the soc node
arm64: dts: imx8mm-venice-gw7902: fix UART1 CTS
arm64: dts: imx8mp: Add support for DH electronics i.MX8M Plus DHCOM and PDK2
...
Link: https://lore.kernel.org/r/20220709082951.15123-5-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.19, round 3:
- Fix GPIO property for imx6qdl-ts7970 board.
- Fix touchscreen pinctrl for imx6ull-colibri board by moving iomuxc-snvs
pin to the correct controller device.
- Fix SFP node of fsl-ls1028a to have a required clock property.
* tag 'imx-fixes-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: colibri-imx6ull: fix snvs pinmux group
ARM: dts: imx6qdl-ts7970: Fix ngpio typo and count
arm64: dts: ls1028a: Update SFP node to include clock
Link: https://lore.kernel.org/r/20220709032716.GA9868@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This adds support for TQMa8MPQL module on MBa8MPxL board.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The proper name is 'keys', not 'scu-keys'.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The proper name is 'system-controller', not 'scu'.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The proper name is 'ocotp', not 'imx8qx-ocotp'.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Both i.MX8QM and i.MX8DXL use the fallback fsl,scu-clk compatible.
They rely on the same driver generic part as the i.MX8QXP, so
lets add it to i.MX8QXP too, for consitency.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The proper name is power-controller, not imx8qx-pd.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
XTAL clocks are not exposed by SCU to OS via OS<->SCU communication protocol,
so remove unnecessary entries.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add i.MX8MP NoC node to make the interconnect i.MX8MP driver could work.
Currently dynamic frequency scaling of the i.MX8MP NoC has not been
supported, only NoC initial settings are configured by interconnect
driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The clocks property is now mandatory. Add it to avoid warning message.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Fixes: eba5bea8f37f ("arm64: dts: ls1028a: add efuse node")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds an SFP node for Trust Architecture 3.0 devices.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds an appropriate SFP node for Trust Architecture 2.1 devices.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.19, round 2:
- Fix the SDIO description for imx7d-smegw01 board to ensure there is
no communication made at 1.8V.
- Fix pgc_ispdwp power-domain clock, which should be
IMX8MP_CLK_MEDIA_ISP_ROOT.
- Re-enable framebuffer support in mxs_defconfig to fix a Kconfig
regression.
- A series from Peng Fan (and Sherry Sun) fixing various pads on i.MX8MP
based boards to leave reserved bits untouched.
* tag 'imx-fixes-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mp-icore-mx8mp-edim2.2: correct pad settings
arm64: dts: imx8mp-phyboard-pollux-rdk: correct i2c2 & mmc settings
arm64: dts: imx8mp-phyboard-pollux-rdk: correct eqos pad settings
arm64: dts: imx8mp-phyboard-pollux-rdk: correct uart pad settings
arm64: dts: imx8mp-venice-gw74xx: correct pad settings
arm64: dts: imx8mp-evk: correct I2C3 pad settings
arm64: dts: imx8mp-evk: correct I2C1 pad settings
arm64: dts: imx8mp-evk: correct I2C5 pad settings
arm64: dts: imx8mp-evk: correct vbus pad settings
arm64: dts: imx8mp-evk: correct eqos pad settings
arm64: dts: imx8mp-evk: correct vbus pad settings
arm64: dts: imx8mp-evk: correct gpio-led pad settings
arm64: dts: imx8mp-evk: correct the uart2 pinctl value
arm64: dts: imx8mp-evk: correct mmc pad settings
ARM: mxs_defconfig: Enable the framebuffer
arm64: dts: imx8mp: correct clock of pgc_ispdwp
ARM: dts: imx7d-smegw01: Fix the SDIO description
Link: https://lore.kernel.org/r/20220629021244.GL819983@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add initial support for phyBOARD-Polis-i.MX8MM.
Main features are:
* Bluetooth and Wifi
* CANFD
* eMMC
* i2c RTC
* Ethernet
* PCIe
* RS232/RS485
* SD-Card
* SPI-NOR flash
* USB
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use IT temperature threshold for critical/passive trip point
on Verdin iMX8M Plus and Mini.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
BIT3 and BIT0 are reserved bits, should not touch.
Fixes: aec8ad34f7f2 ("arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus EDIMM2.2 Starter Kit")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
BIT3 and BIT0 are reserved bits, should not touch.
Fixes: 88f7f6bcca37 ("arm64: dts: freescale: Add support for phyBOARD-Pollux-i.MX8MP")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
BIT3 and BIT0 are reserved bits, should not touch.
Fixes: 6f96852619d5 ("arm64: dts: freescale: Add support EQOS MAC on phyBOARD-Pollux-i.MX8MP")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
BIT3 and BIT0 are reserved bits, should not touch.
Fixes: 846f752866bd ("arm64: dts: imx8mp-phyboard-pollux-rdk: Change debug UART")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to RM bit layout, BIT3 and BIT0 are reserved.
8 7 6 5 4 3 2 1 0
PE HYS PUE ODE FSEL X DSE X
Should not set reserved bit.
Fixes: 7899eb6cb15d ("arm64: dts: imx: Add i.MX8M Plus Gateworks gw7400 dts support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to RM bit layout, BIT3 and BIT0 are reserved.
8 7 6 5 4 3 2 1 0
PE HYS PUE ODE FSEL X DSE X
Although function is not broken, we should not set reserved bit.
Fixes: 5e4a67ff7f69 ("arm64: dts: imx8mp-evk: Add i2c3 support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to RM bit layout, BIT3 and BIT0 are reserved.
8 7 6 5 4 3 2 1 0
PE HYS PUE ODE FSEL X DSE X
Although function is not broken, we should not set reserved bit.
Fixes: 5497bc2a2bff ("arm64: dts: imx8mp-evk: Add PMIC device")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to RM bit layout, BIT3 and BIT0 are reserved.
8 7 6 5 4 3 2 1 0
PE HYS PUE ODE FSEL X DSE X
Although function is not broken, we should not set reserved bit.
Fixes: 8134822db08d ("arm64: dts: imx8mp-evk: add support for I2C5")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to RM bit layout, BIT3 and BIT0 are reserved.
8 7 6 5 4 3 2 1 0
PE HYS PUE ODE FSEL X DSE X
Not set reserved bit.
Fixes: 9e847693c6f3 ("arm64: dts: freescale: Add i.MX8MP EVK board support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|