| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Top-level nodes, not being on MMIO bus, do not have "reg" properties and
should not have unit addresses. Correct their name as well to match
"Generic node names" recommendation from Devicetree specification.
This also fixes dtc W=1 warnings:
cn9130-db.dtsi:28.11-31.4: Warning (unique_unit_address_if_enabled): /memory@0: duplicate unit-address (also used in node /ap0_sd_vccq@0)
cn9130-db.dtsi:28.11-31.4: Warning (unique_unit_address_if_enabled): /memory@0: duplicate unit-address (also used in node /cp0_usb3_vbus@0)
cn9130-db.dtsi:33.33-40.4: Warning (unique_unit_address_if_enabled): /ap0_sd_vccq@0: duplicate unit-address (also used in node /cp0_usb3_vbus@0)
cn9130-db.dtsi:28.11-31.4: Warning (unique_unit_address_if_enabled): /memory@0: duplicate unit-address (also used in node /cp0_usb3_phy@0)
cn9130-db.dtsi:33.33-40.4: Warning (unit_address_vs_reg): /ap0_sd_vccq@0: node has a unit name, but no reg or ranges property
cn9130-db.dtsi:42.38-49.4: Warning (unit_address_vs_reg): /cp0_usb3_vbus@0: node has a unit name, but no reg or ranges property
cn9130-db.dtsi:51.34-54.4: Warning (unit_address_vs_reg): /cp0_usb3_phy@0: node has a unit name, but no reg or ranges property
cn9130-db.dtsi:56.38-63.4: Warning (unit_address_vs_reg): /cp0_usb3_vbus@1: node has a unit name, but no reg or ranges property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Rename the GPIO related sfp properties to include the preffered -gpios
suffix. Also, with this change the dtb_check will no longer complain
when trying to verify the DTS against the sff,sfp.yaml binding.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change all 10G port modes in Armada family device trees from
10gbase-kr to 10gbase-r
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The CN913x DB with topology B is similar to a regular setup (A)
boards, but uses NAND flash as a boot device, while topology A
boards are booting from SPI flash.
Since NAND and SPI on CN913x DB boards share some wires, they
cannot be activated simultaneously.
The DTS files for setup "B" are based on setup "A", in which the
CP0 NAND controller enabled and CP0 SPI1 disabled.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
