| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Now that we no longer have fixed addresses for the firmware memory
regions, disable them by default and only enable them together with
the actual user in the board DT.
This frees up unnecessary reserved memory for boards that do not use
some of the remoteprocs and allows moving selected device-specific
properties (such as firmware size) to the board-specific DT part in
the next step.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-7-b7089ec3e3a1@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Most of the reserved firmware memory on MSM8916 can be relocated when
respecting the required alignment. To avoid having to precompute the
reserved memory regions in every board DT, describe the actual
requirements (size, alignment, alloc-ranges) using the dynamic reserved
memory allocation.
This approach has several advantages:
1. We can define "templates" for the reserved memory regions in
msm8916.dtsi and keep only device-specific details in the board DT.
This is useful for the "mpss" region size for example, which varies
from device to device. It is no longer necessary to redefine all
firmware regions to shift their addresses.
2. When some of the functionality (e.g. WCNSS, Modem, Venus) is not
enabled or needed for a device, the reserved memory can stay
disabled, freeing up the unused reservation for Linux.
3. Devices with special requirements for one of the firmware regions
are handled automatically. For example, msm8916-longcheer-l8150
has non-relocatable "wcnss" firmware that must be loaded exactly
at address 0x8b600000. When this is defined as a static region,
the other dynamic allocations automatically adjust to a different
place with suitable alignment.
All in all this approach significantly reduces the boilerplate necessary
to define the different firmware regions, and makes it easier to enable
functionality on the different devices.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-4-b7089ec3e3a1@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Venus needs firmware that is usually signed with a device-specific key.
There are also devices that might not need it (especially during
bring-up), so let's follow more recent SoCs and disable it by default.
Enable it explicitly for all current devices except msm8916-mtp. That
one has just UART enabled currently so it cannot really benefit from
Venus.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-1-b7089ec3e3a1@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
liteon,ltr559 light sensor takes VDDIO, not VIO, supply:
msm8916-longcheer-l8150.dtb: light-sensor@23: 'vio-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: 3016af34ef8d ("arm64: dts: qcom: msm8916-longcheer-l8150: Add light and proximity sensor")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20230617171541.286957-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
MSM8939 has the SDC pinctrl consolidated in two &sdcN_default and
&sdcN_sleep states, while MSM8916 has all pins separated. Make this
consistent by consolidating them for MSM8916 well.
Use this as a chance to define default pinctrl in the SoC.dtsi and only
let boards that add additional definitions (such as cd-gpios) override it.
For MSM8939 just make the label consistent with the other pinctrl
definitions (they do not have a _state suffix).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-2-11f540b51c93@gerhold.net
|
|
MSM8939 has the aliases defined separately for each board (because
there could be (theoretically) a board where the slots are numbered
differently. To make MSM8916 and MSM8939 more consistent do the same
for all MSM8916 boards and move aliases there.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-6-bec0f5fb46fb@gerhold.net
|
|
For some reason the BLSP UART controllers have a label with a number
behind blsp (&blsp1_uartN) while I2C/SPI are named without (&blsp_i2cN).
This is confusing, especially for proper node ordering in board DTs.
Right now all board DTs are ordered as if the number behind blsp does
not exist (&blsp_i2cN comes before &blsp1_uartN). Strictly speaking
correct ordering would be the other way around ('1' comes before '_').
End this confusion by giving the UART controllers consistent labels.
There is just one BLSP on MSM8916/39 so the number is redundant.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-2-bec0f5fb46fb@gerhold.net
|
|
MSM8916 is the only ARM64 Qualcomm SoC that is still using the old
&msmgpio name. Change this to &tlmm to avoid confusion.
Note that the node ordering does not change because the MSM8916 device
trees have pinctrl separated at the bottom (similar to sc7180).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-1-bec0f5fb46fb@gerhold.net
|
|
Right now each MSM8916 device has a huge block of regulator constraints
with allowed voltages for each regulator. For lack of better
documentation these voltages are often copied as-is from the vendor
device tree, without much extra thought.
Unfortunately, the voltages in the vendor device trees are often
misleading or even wrong, e.g. because:
- There is a large voltage range allowed and the actual voltage is
only set somewhere hidden in some messy vendor driver. This is often
the case for pm8916_{l14,l15,l16} because they have a broad range of
1.8-3.3V by default.
- The voltage is actually wrong but thanks to the voltage constraints
in the RPM firmware it still ends up applying the correct voltage.
To have proper regulator constraints it is important to review them in
context of the usage. The current setup in the MSM8916 device trees
makes this quite hard because each device duplicates the standard
voltages for components of the SoC and mixes those with minor
device-specific additions and dummy voltages for completely unused
regulators.
The actual usage of the regulators for the SoC components is in
msm8916-pm8916.dtsi, so it can and should also define the related
voltage constraints. These are not board-specific but defined in the
APQ8016E/PM8916 Device Specification. The board DT can then focus on
describing the actual board-specific regulators, which makes it much
easier to review and spot potential mistakes there.
Note that this commit does not make any functional change. All used
regulators still have the same regulator constraints as before. Unused
regulators do not have regulator constraints anymore because most of
these were too broad or even entirely wrong. They should be added back
with proper voltage constraints when there is an actual usage.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-7-54d4960a05fc@gerhold.net
|
|
The regulator constraints for most MSM8916 devices (except DB410c) were
originally taken from Qualcomm's msm-3.10 vendor device tree (for lack
of better documentation). Unfortunately it turns out that Qualcomm's
voltages are slightly off as well and do not match the voltage
constraints applied by the RPM firmware.
This means that we sometimes request a specific voltage but the RPM
firmware actually applies a much lower or higher voltage. This is
particularly critical for pm8916_l11 which is used as SD card VMMC
regulator: The SD card can choose a voltage from the current range of
1.8 - 2.95V. If it chooses to run at 1.8V we pretend that this is fine
but the RPM firmware will still silently end up configuring 2.95V.
This can be easily reproduced with a multimeter or by checking the
SPMI hardware registers of the regulator.
Fix this by making the voltages match the actual "specified range" in
the PM8916 Device Specification which is enforced by the RPM firmware.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-3-54d4960a05fc@gerhold.net
|
|
On MSM8916 the wireless connectivity functionality (WiFi/Bluetooth) is
split into the digital part inside the SoC and the analog RF part inside
a supplementary WCN36xx chip. For MSM8916, three different options
exist:
- WCN3620 (WLAN 802.11 b/g/n 2.4 GHz + Bluetooth)
- WCN3660B (WLAN 802.11 a/b/g/n 2.4/5 GHz + Bluetooth)
- WCN3680B (WLAN 802.11ac 2.4/5 GHz + Bluetooth)
Choosing one of these is up to the board vendor. This means that the
compatible belongs into the board-specific DT part so people porting
new boards pay attention to set the correct compatible.
Right now msm8916.dtsi sets "qcom,wcn3620" as default compatible,
which does not work at all for boards that have WCN3660B or WCN3680B.
Remove the default compatible from msm8196.dtsi and move it to the board
DT as follows:
- Boards with only &pronto { status = "okay"; } used the default
"qcom,wcn3620" so far. They now set this explicitly for &wcnss_iris.
- Boards with &pronto { ... iris { compatible = "qcom,wcn3660b"; }};
already had an override that just moves to &wcnss_iris now.
- For msm8916-samsung-a2015-common.dtsi the WCN compatible differs for
boards making use of it (a3u: wcn3620, a5u: wcn3660b, e2015: wcn3620)
so the definitions move to the board-specific DT part.
Since this requires touching all the board DTs, use this as a chance to
name the WCNSS-related labels consistently, so everything is grouped
properly when sorted alphabetically.
No functional change, just clean-up for more clarity & easier porting.
Aside from ordering the generated DTBs are identical.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309091452.1011776-1-stephan.gerhold@kernkonzept.com
|
|
Switch '//' comments to C-style /* */ and fix up the contents of some.
Make sure all multiline C-style commends begin with just '/*' with
the comment text starting on a new line.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221107145522.6706-2-konrad.dybcio@linaro.org
|
|
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024002356.28261-2-krzysztof.kozlowski@linaro.org
|
|
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-21-krzysztof.kozlowski@linaro.org
|
|
L8150 uses LTR559 as a light and proximity sensor. Add it to the
devicetree.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220219145140.84712-1-nikita@trvn.ru
|
|
A new 'chassis-type' root node property has recently been approved for
the device-tree specification, in order to provide a simple way for
userspace to detect the device form factor and adjust their behavior
accordingly.
This patch fills in this property for end-user devices (such as laptops,
smartphones and tablets) based on Qualcomm ARM64 processors.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net> # msm8916
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211016102025.23346-4-arnaud.ferraris@collabora.com
|
|
At the moment, longcheer-l8150 is using a dummy extcon-usb-gpio device
that permanently enables USB gadget mode. This workaround allows USB
to work but is actually wrong and confusing. The "vbus-gpio" used there
refers to an unused (floating) GPIO that is pulled up to make
extcon-usb-gpio report USB gadget mode permanently.
Replace this with the new &pm8916_usbin extcon device that actually
reports if an USB cable is attached or not. This allows the USB PHY
to be turned off when there is no USB cable attached and is much
cleaner overall.
Fixes: 16e8e8072108 ("arm64: dts: qcom: Add device tree for Longcheer L8150")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-3-stephan@gerhold.net
|
|
So far there were no interrupts set up for the BMC150 accelerometer
+ magnetometer combo because they were broken for some reason.
It turns out Longcheer L8150 actually has a BMC156 which is very similar
to BMC150, but only has an INT2 pin for the accelerometer part.
This requires some minor changes in the bmc150-accel driver which is now
supported by using the more correct bosch,bmc156_accel compatible.
Unfortunately it looks like even INT2 is not functional on most boards
because the interrupt line is not actually connected to the BMC156.
However, there are two pads next to the chip that can be shorted
to make it work if needed.
While at it, add the missing interrupts for the magnetometer part
and extra BMG160 gyroscope, those seem to work without any problems.
Also correct the magnetometer compatible to bosch,bmc156_magn for clarity
(no functional difference for the magnetometer part).
Tested-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210816123544.14027-1-stephan@gerhold.net
|
|
L8150 uses aw2013 LED contriller for notification LED on the front
of the device. Add it to the device tree
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-5-nikitos.tr@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
L8150 uses SGM3785 Flash LED driver. It is similar to SGM3140 but
can also be controlled with PWM. Since SoC doesn't have PWM, add
led to the device tree using sgm3140 driver.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-4-nikitos.tr@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
L8150 has:
- BMC156 accelerometer and magnetic sensor
- BMG160 gyroscope sensor
Add them to the device tree.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-3-nikitos.tr@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
L8150 has RMI4 compatible Synaptics touchscreen on
blsp_i2c5. It is powered by fixed regulator. Add
both to the device tree.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-2-nikitos.tr@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
L8150 has a vibrator connected to PM8916. Add it to the device tree.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-1-nikitos.tr@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
s1 (VDDCX) and l3 (VDDMX) are now managed by rpmpd as power domains.
This allows us to vote for voltage corners instead of voting for raw
voltages. But we cannot manage these as regulator and power domain at
the same time: The votes by rpmpd would conflict with the ones from
the regulator driver.
All users of these regulators have been converted to power domains.
Make sure that no new users are added by removing s1 and l3 from
the regulator definitions.
This also allows us to remove the arbitrary voltage constraints
we have been using for these regulators. Not all of the voltages
listed there would actually have been safe for the boards.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200916104135.25085-11-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Right now we define "hnp-disable", "srp-disable", "adp-disable"
separately for every MSM8916 board that has USB working.
They are needed for USB to work properly if CONFIG_USB_OTG_FSM
is enabled. This is because the chipidea OTG FSM code waits for
interrupts regarding the VBUS state (AVVIS). Those never happen
on MSM8916 because VBUS is always connected to the PMIC instead
of the USB controller.
There was a patch [1] to work around this but ultimately it was
decided that it's easier to disable the OTG FSM altogether using
these properties. This works fine for most use cases, because the
OTG FSM isn't needed for simple dual role host/gadget operation.
Given that these properties are needed for every MSM8916 device,
move them to msm8916.dtsi so we can avoid some more duplication.
[1]: https://lore.kernel.org/lkml/20160707222114.1673-10-stephen.boyd@linaro.org/
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-11-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Right now some device nodes set default pinctrl within msm8916.dtsi
(e.g. I2C, SPI), but for others it needs to be explicitly set in the
board-specific device tree (e.g. UART).
While it is theoretically possible that some super special board
needs different pinctrl for these, in practice pretty much every
board ends up using the common pinctrl definitions.
Make this consistent by also defining the common pinctrl properties
for blsp1_uart1 and blsp1_uart2 so we don't need to copy this for every
board. If there is really such a super special board it could just
override these properties with custom pinctrl or make minor modifications
to the common pinctrl configurations provided by msm8916-pins.dtsi.
Also move #address-cells/#size-cells for &dsi0 to msm8916.dtsi
since this is specific to the DSI node, not the board.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-10-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
So far we had some supplies defined for all boards in msm8916.dtsi,
while others were duplicated into every board-specific device tree.
Now that we have msm8916-pm8916.dtsi as a common include for all
standard MSM8916 devices using PM8916, move the remaining common
supplies to msm8916-pm8916.dtsi to reduce duplication a bit.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-9-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Device trees for newer SoCs avoid defining the regulator nodes directly
in the SoC device tree (here: msm8916.dtsi). The reason for this is that
theoretically it is possible to combine the SoC with a different PMIC,
or to use all the regulators in a board-specific way.
Therefore let's remove those from the SoC include (msm8916.dtsi).
In practice, pretty much all MSM8916 boards were combined with PM8916,
and use the regulators in similar ways. After looking at many different
MSM8916 boards (mostly smartphones and tablets), I haven't seen a single
device that isn't using the same regulators for components integrated
into the SoC.
If all boards end up defining all regulators and supplies in the same way
then it is useful to have an include for that, so we can avoid duplicating
it everywhere. If there is really a super special board that does it
differently it could just override some properties or avoid using the
include altogether.
This patch moves the regulator and common supply definitions to
a new include called "msm8916-pm8916.dtsi".
This is also going to be useful when introducing CPR (Core Power
Reduction) later because we can configure the CPU regulator
(pm8916_spmi_s2) for all devices in this common include.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-8-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Right now we define the entire pm8916 resin node separately in
the board-specific device tree part, including the interrupt that
belongs to PM8916.
As a feature of the PMIC it should be declared in pm8916.dtsi,
disabled by default. Like all other optional components it can then
by enabled and configured in the board-specific device tree part.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-7-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Device trees for newer SoCs avoid replicating the entire device
hierarchy in the board-specific device tree part. Instead,
they set additional properties only by referencing labels,
sorted alphabetically.
Now that we have labels for all relevant nodes, convert the MSM8916
board device trees to use the same style and remove the "soc" node
entirely.
Note: There is a large block of coresight nodes in apq8016-sbc.dtsi,
which are enabled by setting status = "okay". I kept them grouped
together (not alphabetically sorted with everything else),
since that would be just unnecessarily verbose and hard to see.
This commit only moves all existing properties to nodes that reference
the respective label. The resulting binary DTBs are exactly the same.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-6-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
So far we have been separating pinctrl entries into pinmux/pinconf.
It turns out it is also possible to combine them: The advantage is
that the device tree is overall more concise because the "pins"
to configure just need to be specified once, not separately for
pinmux/pinconf.
Using the simpler form only for new entries would be rather confusing.
This commit makes all MSM8916 device trees use the simplfied form.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
It is helpful to be able to see all hardware components in one part
of the device tree, without having to scroll over the large amount
of regulator/pinctrl nodes. Keep those separated at the end of the file
to make navigation a bit easier.
This also makes it consistent with the order used in apq8016-sbc.dtsi.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Many nodes in the MSM8916 device trees use '_' in node names
(especially pinctrl), even though (seemingly) '-' is preferred now.
Make this more consistent by replacing '_' with '-' where possible.
Similar naming is used for pinctrl in newer device trees (e.g. sdm845.dtsi).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200514112754.148919-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
On some msm8916 devices, attempts at initializing coresight cause the boot to
fail. This was fixed by disabling the coresight-related nodes in the board dts
files. However, a cleaner approach was chosen for fixing the same issue on
msm8998: disabling coresight by default, and enabling it in board dts files
where desired.
This patch implements the same solution for msm8916, removes now redundant
overwrites in board specific dts files and and enables coresight in db410c's
board dts in order to keep the current behavior.
Fixes: b1fcc5702a41 ("arm64: dts: qcom: msm8916: Add CTI options")
Signed-off-by: Michael Srba <michael.srba@seznam.cz>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20200513184735.30104-1-michael.srba@seznam.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add nodes for Volume UP button connected to GPIO and Volume DOWN button,
which is handled by the pm8916 as is common with msm8916 devices.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
WCNSS is used on L8150 for WiFi and BT.
Its firmware isn't relocatable and must be loaded at specific address.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Longcheer L8150 is a smartphone based on MSM8916 which is
used in several rebrands like the Snapdragon 410
Android One devices or the Wileyfox Swift.
Add a device tree for L8150 with initial support for:
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- Regulators
Co-developed-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
