| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Replace hard-coded interrupt parts (GIC, flags) with standard defines
for readability. No changes in resulting DTBs.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230730180638.23539-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Currently in board files MDSS and DSI nodes stay apart, because labels
for DSI nodes do not have the mdss_ prefix. It was found that grouping
all display-related notes is more useful.
To keep all display-related nodes close in the board files, change DSI
node labels from dsi_* to mdss_dsi_*.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-12-dmitry.baryshkov@linaro.org
|
|
Enable the PMI8998/smb2 charger, and denote the secondary SMB1355
charger which is used for parallel charging.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230524-pmi8998-charger-dts-v2-4-2a5c77d2ff0c@linaro.org
|
|
The SHIFT6mq (axolotl) is an SDM845-based smartphone with 2 flash LEDs.
One LED is white, the other one is yellow. Define both LEDs in the DTS
so they can be used as flash or torch and enable the flash LED
controller to control them in PMI8998.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230518133113.273880-4-me@dylanvanassche.be
|
|
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-6-krzysztof.kozlowski@linaro.org
|
|
Enable the SLPI DSP on the SHIFTPHONES SHIFT6mq phone with a
Qualcomm SDM845 SoC.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-6-me@dylanvanassche.be
|
|
Device node names should be generic and bindings expect certain pattern
for RPMh regulator nodes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230127114347.235963-6-krzysztof.kozlowski@linaro.org
|
|
Depending on the platform, either the modem or the AP must load GSI
firmware for IPA before it can be used. To date, this has been
indicated by the presence or absence of a "modem-init" property.
That mechanism has been deprecated. Instead, we indicate how GSI
firmware should be loaded by the value of the "qcom,gsi-loader"
property.
Update all arm64 platforms that use IPA to use the "qcom,gsi-loader"
property to specify how the GSI firmware is loaded.
Update the affected nodes so the status property is last.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
[bjorn: Moved sc7280 change herobrine-lte-sku]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221231002716.2367375-3-elder@linaro.org
|
|
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221222151319.122398-3-krzysztof.kozlowski@linaro.org
|
|
resin node declaration was moved to pm8998.dtsi file (in disabled state).
MSM8998 and SDM845 boards defining resin node did not previously have
status="okay" and ended up disabled.
Re-enable it by using resin node link from pm8998.dtsi with status="okay".
Fixes: f86ae6f23a9e ("arm64: dts: qcom: sagit: add initial device tree for sagit")
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reported-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/linux-arm-msm/20221222115922.jlachctn4lxopp7a@SoMainline.org/
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221228115243.201038-1-dsankouski@gmail.com
|
|
The gpio node in PMIC dts'es define access to multiple GPIOs. Most Qcom
PMICs were already using the plural _gpios label to point to this node,
but a few PMICs were left behind including the recently-pulled
pm(i)8950.
Rename it from *_gpio to *_gpios for pm6125, pm6150(l), pm8005,
pm(i)8950, and pm(i)8998.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209220450.1793421-1-marijn.suijten@somainline.org
|
|
Add serial1 alias, firmware name and use 4 pin UART pinmux.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221016172944.1892206-3-kc@postmarketos.org
|
|
Enables the RGB notification LED on the SHIFT 6mq (sdm845-shift-axolotl)
with the Qualcomm Light Pulse Generator bindings by Bjorn Andersson [1].
Patches are merged in for-next branch of linux-leds.
Tested these changes on the SHIFT 6mq.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds.git/commit/?h=for-next&id=a8e53db46f19f67be6a26488aafb7d10c78e33bd
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Reviewed-by: Alexander Martinz <amartinz@shiftphones.com>
Tested-by: Alexander Martinz <amartinz@shiftphones.com>
Tested-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220512054439.13971-1-me@dylanvanassche.be
|
|
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-21-krzysztof.kozlowski@linaro.org
|
|
Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment. No functional
changes (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220526204248.832139-1-krzysztof.kozlowski@linaro.org
|
|
DT schema expects PMIC GPIO pin configuration nodes to be named with
'-state' suffix. Optional children should be either 'pinconf' or
followed with '-pins' suffix. This fixes dtbs_check warnings like:
sdm845-xiaomi-beryllium.dtb: gpios@c000: 'vol-up-active' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220507194913.261121-6-krzysztof.kozlowski@linaro.org
|
|
Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.
It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20220407225254.2178644-1-robh@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add initial support for the SHIFT SHIFT6mq (axolotl) based on
the sdm845-mtp DT.
Currently supported features:
* Buttons (power, volume)
* Bluetooth, DSPs and modem
* Display and GPU
* Touch
* UART
* USB peripheral mode
* WLAN
Co-developed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220123173650.290349-7-caleb@connolly.tech
|
