| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Qualcomm's Hardware Development Kits devices are embedded platforms,
set the chassis-type property to 'embedded'.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230622-topic-sm8x50-upstream-chassis-type-v1-3-13f676eb71f3@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Device node names should be generic and bindings expect certain pattern
for RPMh regulator nodes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230127114347.235963-9-krzysztof.kozlowski@linaro.org
|
|
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-21-krzysztof.kozlowski@linaro.org
|
|
The following properties are not supported and causing dtbs_check
warnings.
- vdda-phy-max-microamp
- vdda-pll-max-microamp
- vddp-ref-clk-max-microamp
- vddp-ref-clk-always-on
Drop them from QMP PHY nodes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210929034253.24570-6-shawn.guo@linaro.org
|
|
It's not worth duplicating the same node over and over and over and over again,
so let's keep the common bits in the pm8150 DTSI, making only changing the
status and keycode necessary.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210613124822.124039-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Almost any board that boots and has a way to interact with it
(say for the rare cases of just-pstore or let's-rely-on-bootloader-setup)
needs to set some GPIOs, so it makes no sense to include gpio.h separately
each time. Hence move it to SoC DTSI.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210616002321.74155-3-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Components that rely on proprietary (not to mention signed!) firmware should
not be enabled by default, as lack of the aforementioned firmware could cause
various issues, from random errors to straight-up failing to boot.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210612192358.62602-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The uart2 node has been renamed, apply the change to sm8250-hdk dts too so
that serial output works.
Fixes: 91ed0e90fc49 ("arm64: dts: qcom: add sm8250 hdk dts")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20201123143538.14198-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add initial HDK865 dts, based on sm8250-mtp, with a few changes.
Notably, regulator configs are changed a bit.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200609194030.17756-9-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
