Age | Commit message (Collapse) | Author | Files | Lines |
|
[ Upstream commit c1a6018d1839c9cb8f807dc863a50102a1a5c412 ]
ls1046afrwy and ls1046ardb boards have CAT24C04[1] and CAT24C05[2]
eeproms respectively. Both are 4Kb (512 bytes) in size,
and compatible with AT24C04[3].
Remove multi-address entries, as both the boards have a single chip each.
[1] https://www.onsemi.com/pdf/datasheet/cat24c01-d.pdf
[2] https://www.onsemi.com/pdf/datasheet/cat24c03-d.pdf
[3] https://ww1.microchip.com/downloads/en/DeviceDoc/doc0180.pdf
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd306fdb4e60bcb1d7ea5431a74092803d3784a6 ]
The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12
is the power-enable to the TPS25821 Source controller and power switch
responsible for monitoring the CC pins and enabling VBUS. Therefore
GPIO1_12 must always be enabled and the vbus output enable from the
IMX8MM can be ignored.
To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the
TPS25821 and change the regulator output to GPIO1_10 which is
unconnected.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 500659f3b401fe6ffd1d63f2449d16d8a4204db7 ]
The GW700x PMIC does not have an interrupt. Remove the invalid pin
config.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 092cd75e527044050ea76bf774e7d730709b7e8b ]
Fix various MP5416 PMIC configurations:
- Update regulator names per dt-bindings
- ensure values fit among valid register values
- add required regulator-max-microamp property
- add regulator-always-on prop
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f865d0292ff3c0ca09414436510eb4c815815509 ]
The documented compatible string for the CPUs found on Tegra132 is
"nvidia,tegra132-denver", rather than the previously used compatible
string "nvidia,denver".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 77b53d65dc1e54321ec841912f06bcb558a079c0 ]
The unit address of the epss_l3 node is incorrect and does not match
the address of its "reg" property. Let's fix it.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20210211193637.9737-1-georgi.djakov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 84f3efbe5b4654077608bc2fc027177fe4592321 ]
We have underscore (_) in node name leading to warning:
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: clocks: xo_board: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[19200000]], 'clock-output-names': ['xo_board'], 'phandle': [[115]]}
Fix this by changing node name to use dash (-)
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-10-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c678beca7ed3fa8a2c6d86f6603bc23400f9ad8 ]
We have underscore (_) in node name leading to warning:
arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dt.yaml: clocks: xo_board: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[19200000]], 'phandle': [[26]]}
arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dt.yaml: clocks: sleep_clk: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[32768]]}
Fix this by changing node name to use dash (-)
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-9-vkoul@kernel.org
[bjorn: Added clock-output-names to satisfy parent_names]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 639dfdbecd88ec05bda87b1d5d419afad50af21c ]
We have underscore (_) in node name so fix that up as well.
Fix this by changing node name to use dash (-)
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-11-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1b91b8ef60e9a67141e66af3cca532c00f4605fe ]
Nodes need not contain '0x' for the unit address. Drop it to fix the
below warning:
arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dt.yaml: reserved-memory:
'memory@0x60000' does not match any of the regexes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-19-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c81210e38966cfa1c784364e4035081c3227cf5b ]
memory node like other node should be node@reg, which is missing in this
case, so fix it up
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: /: memory: False schema does not allow {'device_type': ['memory'], 'reg': [[0, 1073741824, 0, 536870912]]}
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-18-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 52c9887fba71fc8f12d343833fc595c762aac8c7 ]
reg property should be array of values, here it is a single array,
leading to below warning:
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@10000000:reg:0: [268435456, 3869, 268439328, 168, 557056, 8192, 269484032, 4096] is too long
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@10000000:ranges: 'oneOf' conditional failed, one must be fixed:
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@10000000:ranges: 'oneOf' conditional failed, one must be fixed:
[[2164260864, 0, 270532608, 270532608, 0, 1048576, 2181038080, 0, 271581184, 271581184, 0, 13631488]] is not of type 'null'
[2164260864, 0, 270532608, 270532608, 0, 1048576, 2181038080, 0, 271581184, 271581184, 0, 13631488] is too long
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@20000000:reg:0: [536870912, 3869, 536874784, 168, 524288, 8192, 537919488, 4096] is too long
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@20000000:ranges: 'oneOf' conditional failed, one must be fixed:
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@20000000:ranges: 'oneOf' conditional failed, one must be fixed:
[[2164260864, 0, 538968064, 538968064, 0, 1048576, 2181038080, 0, 540016640, 540016640, 0, 13631488]] is not of type 'null'
[2164260864, 0, 538968064, 538968064, 0, 1048576, 2181038080, 0, 540016640, 540016640, 0, 13631488] is too long
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-17-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 36a0d47aee6a8cfd3c6cf4274732d8ef994a25b4 ]
Previous pinctrl configuration was wrong. Fix it and clean up how
multi-pin states are described.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210728222542.54269-9-konrad.dybcio@somainline.org
[bjorn: Polished the commit message]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 26e02c98a9ad63eb21b9be4ac92002f555130d3b ]
The memory map was wrong. Fix it.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210728222542.54269-2-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bf2942a8b7c38e8cc2d5157b4f0323d7f4e5ec71 ]
The initialization sequence performed by the generic platform driver
pcie-designware-plat.c for a DWC based implementation doesn't work for
Tegra194. Tegra194 has a different initialization sequence requirement
which can only be satisfied by the Tegra194 specific platform driver
pcie-tegra194.c. So, remove the generic compatible string "snps,dw-pcie-ep"
from Tegra194's endpoint controller nodes.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7ab1f6539762946de06ca14d7401ae123821bc40 ]
Regulator node names don't reflect class of the device. Fix that by
prefixing names with "regulator-".
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210722161220.51181-2-jernej.skrabec@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 514ef1e62d6521c2199d192b1c71b79d2aa21d5a ]
Current PCIe MEM space of size 16 MB is not enough for some combination
of PCIe cards (e.g. NVMe disk together with ath11k wifi card). ARM Trusted
Firmware for Armada 3700 platform already assigns 128 MB for PCIe window,
so extend PCIe MEM space to the end of 128 MB PCIe window which allows to
allocate more PCIe BARs for more PCIe cards.
Without this change some combination of PCIe cards cannot be used and
kernel show error messages in dmesg during initialization:
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01800000]
pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x01800000]
pci 0000:00:00.0: BAR 6: assigned [mem 0xe8000000-0xe80007ff pref]
pci 0000:01:00.0: BAR 8: no space for [mem size 0x01800000]
pci 0000:01:00.0: BAR 8: failed to assign [mem size 0x01800000]
pci 0000:02:03.0: BAR 8: no space for [mem size 0x01000000]
pci 0000:02:03.0: BAR 8: failed to assign [mem size 0x01000000]
pci 0000:02:07.0: BAR 8: no space for [mem size 0x00100000]
pci 0000:02:07.0: BAR 8: failed to assign [mem size 0x00100000]
pci 0000:03:00.0: BAR 0: no space for [mem size 0x01000000 64bit]
pci 0000:03:00.0: BAR 0: failed to assign [mem size 0x01000000 64bit]
Due to bugs in U-Boot port for Turris Mox, the second range in Turris Mox
kernel DTS file for PCIe must start at 16 MB offset. Otherwise U-Boot
crashes during loading of kernel DTB file. This bug is present only in
U-Boot code for Turris Mox and therefore other Armada 3700 devices are not
affected by this bug. Bug is fixed in U-Boot version 2021.07.
To not break booting new kernels on existing versions of U-Boot on Turris
Mox, use first 16 MB range for IO and second range with rest of PCIe window
for MEM.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 76f6386b25cc ("arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 01c72cad790cb6cd3ccbe4c1402b6cb6c6bbffd0 ]
The GIC-400 CPU interfaces address range is defined as 0x2000-0x3FFF (by
ARM).
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Fixes: b9024cbc937d ("arm64: dts: Add initial device tree support for exynos7")
Link: https://lore.kernel.org/r/20210805072110.4730-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c96ca5604a889a142d6b60889cc6da48498806e9 ]
Hihope boards use Realtek PHY. From the very beginning it use only
tx delays. However the phy driver commit bbc4d71d63549bcd003
("net: phy: realtek: fix rtl8211e rx/tx delay config") introduced
NFS mount failure. Now it needs rx delay inaddition to tx delay
for NFS mount to work. This patch fixes NFS mount failure issue
by adding MAC internal rx delay.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: bbc4d71d63549bcd ("net: phy: realtek: fix rtl8211e rx/tx delay config")
Link: https://lore.kernel.org/r/20210721180632.15080-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 63fa4322469648ae1023bb92a8b0d6a2f4bdaf2c ]
Use 'lanes' as SuperSpeed lanes device node instead of just 'lane' to
fix issues with TypeC support.
Fixes: 46a6f297d7dd ("arm64: dts: qcom: sm8250: Add USB and PHY device nodes")
Cc: robh+dt@kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20210706230702.299047-2-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a8c7f3100e708d5f55692f0607ca80c5dcd21ce8 ]
Set audu wakeup delay to 80 ms for fixing pop noise during capture begin.
Fixes: ba5f9b5d7ff3 ("arm64: dts: qcom: sc7180: Add wakeup delay for adau codec")
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210708090810.174767-1-judyhsiao@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ec82a7bb3db8c6005e715c63224c32d458917a2 ]
The "max-clock" and "min-vrefresh" properties fail to validate with
commit cfe34bb7a770c5d8 ("dt-bindings: drm: bridge: adi,adv7511.txt:
convert to yaml"). Drop them, as they are parts of an out-of-tree
workaround that is not needed upstream.
Fixes: bcf3003438ea4645 ("arm64: dts: renesas: r8a77995: draak: Enable HDMI display output")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/975b6686bc423421b147d367fe7fb9a0db99c5af.1625134398.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f890f89d9a80fffbfa7ca791b78927e5b8aba869 upstream.
Reserve GPIO pins 85-88 as these aren't meant to be accessible from the
application CPUs (causes reboot). Yet another fix similar to
9134586715e3, 5f8d3ab136d0, which is needed to allow angler to boot after
3edfb7bd76bd ("gpiolib: Show correct direction from the beginning").
Fixes: feeaf56ac78d ("arm64: dts: msm8994 SoC and Huawei Angler (Nexus 6P) support")
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210415193913.1836153-1-petr.vorel@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d77c95bf9a64d8620662151b2b10efd8221f4bcc ]
Fix the upper guard and the "removed_region", this fixes the random
crashes which used to occur in memory intensive loads. I'm not sure WHY
the upper guard being 0x2000 instead of 0x1000 doesn't fix this, but it
HAS to be 0x1000.
Fixes: e60fd5ac1f68 ("arm64: dts: qcom: sdm845-oneplus-common: guard rmtfs-mem")
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Link: https://lore.kernel.org/r/20210720153125.43389-2-caleb@connolly.tech
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0e5ded926f2a0f8b57dfa7f0d69a30767e1ea2ce ]
As the default definition breaks booting angler:
[ 1.862561] printk: console [ttyMSM0] enabled
[ 1.872260] msm_serial: driver initialized
D - 15524 - pm_driver_init, Delta
cont_splash_mem was introduced in 74d6d0a145835, but the problem
manifested after commit '86588296acbf ("fdt: Properly handle "no-map"
field in the memory region")'.
Disabling it because Angler's firmware does not report where the memory
is allocated (dmesg from downstream kernel):
[ 0.000000] cma: Found cont_splash_mem@0, memory base 0x0000000000000000, size 16 MiB, limit 0x0000000000000000
[ 0.000000] cma: CMA: reserved 16 MiB at 0x0000000000000000 for cont_splash_mem
Similar issue might be on Google Nexus 5X (lg-bullhead). Other MSM8992/4
are known to report correct address.
Fixes: 74d6d0a145835 ("arm64: dts: qcom: msm8994/8994-kitakami: Fix up the memory map")
Suggested-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Link: https://lore.kernel.org/r/20210622191019.23771-1-petr.vorel@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3cb6a271f4b04f11270111638c24fa5c0b846dec ]
cont_splash_mem has different memory mapping than generic from msm8994.dtsi:
[ 0.000000] cma: Found cont_splash_mem@0, memory base 0x0000000003400000, size 12 MiB, limit 0xffffffffffffffff
[ 0.000000] cma: CMA: reserved 12 MiB at 0x0000000003400000 for cont_splash_mem
This fixes boot.
Fixes: 976d321f32dc ("arm64: dts: qcom: msm8992: Make the DT an overlay on top of 8994")
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Link: https://lore.kernel.org/r/20210713185734.380-3-petr.vorel@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9d1fc2e4f5a94a492c7dd1ca577c66fdb7571c84 ]
Bullhead firmware obviously doesn't support PSCI as it fails to boot
with this definition.
Fixes: 329e16d5f8fc ("arm64: dts: qcom: msm8992: Add PSCI support.")
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Link: https://lore.kernel.org/r/20210713185734.380-2-petr.vorel@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9a253bb42f190efd1a1c156939ad7298b3529dca ]
WSA881x powerdown pin is connected to GPIO1, GPIO2 not GPIO2 and GPIO3,
so correct this. This was working so far due to a shift bug in gpio driver,
however once that is fixed this will stop working, so fix this!
For some reason we forgot to add this dts change in last merge cycle so
currently audio is broken in 5.13 as the gpio driver fix already landed
in 5.13.
Reported-by: Shawn Guo <shawnguo@kernel.org>
Fixes: 45021d35fcb2 ("arm64: dts: qcom: c630: Enable audio support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20210706083523.10601-1-srinivas.kandagatla@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ee7ab3f263f8131722cff3871b9618b1e7478f07 ]
Some SFP modules are not detected when i2c-fast-mode is enabled even when
clock-frequency is already set to 100000. The I2C bus violates the timing
specifications when run in fast mode. So disable fast mode on Turris Mox.
Same change was already applied for uDPU (also Armada 3720 board with SFP)
in commit fe3ec631a77d ("arm64: dts: uDPU: remove i2c-fast-mode").
Fixes: 7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 923f98929182dfd04e9149be839160b63a3db145 ]
Since drivers/mmc/host/sdhci-xenon.c declares the PROBE_PREFER_ASYNCHRONOUS
probe type, it is not guaranteed whether /dev/mmcblk0 will belong to
sdhci0 or sdhci1. In turn, this will break booting by:
root=/dev/mmcblk0p1
Fix the issue by adding aliases so that the old MMC controller indices
are preserved.
Fixes: 7320915c8861 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.14")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 29f6a20c21b5bdc7eb623a712bbf7b99612ee746 ]
The PHY configuration for the variant 2 is still missing the flag for
in-band signalling between PHY and MAC. Both sides - MAC and PHY - have
to match the setting. For now, Linux only supports setting the MAC side
and thus it has to match the setting the bootloader is configuring.
Enable in-band signalling to make ethernet work.
Fixes: ab43f0307449 ("arm64: dts: ls1028a: sl28: add support for variant 2")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7e71b85473f863a29eb1c69265ef025389b4091d ]
U-Boot attempts to fix up the "clock-frequency" property of the "/sysclk" node:
https://elixir.bootlin.com/u-boot/v2021.04/source/arch/arm/cpu/armv8/fsl-layerscape/fdt.c#L512
but fails to do so:
## Booting kernel from Legacy Image at a1000000 ...
Image Name:
Created: 2021-06-08 10:31:38 UTC
Image Type: AArch64 Linux Kernel Image (gzip compressed)
Data Size: 15431370 Bytes = 14.7 MiB
Load Address: 80080000
Entry Point: 80080000
Verifying Checksum ... OK
## Flattened Device Tree blob at a0000000
Booting using the fdt blob at 0xa0000000
Uncompressing Kernel Image
Loading Device Tree to 00000000fbb19000, end 00000000fbb22717 ... OK
Unable to update property /sysclk:clock-frequency, err=FDT_ERR_NOTFOUND
Starting kernel ...
All Layerscape SoCs except LS1028A use "sysclk" as the node name, and
not "clock-sysclk". So change the node name of LS1028A accordingly.
Fixes: 8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3a52a48973b355b3aac5add92ef50650ae37c2bd ]
Move the turris-mox-rwtm firmware node from Turris MOX' device tree into
the generic armada-37xx.dtsi file and use the generic compatible string
'marvell,armada-3700-rwtm-firmware' instead of the current one.
Turris MOX DTS file contains also old compatible string for backward
compatibility.
The Turris MOX rWTM firmware can be used on any Armada 37xx device,
giving them access to the rWTM hardware random number generator, which
is otherwise unavailable.
This change allows Linux to load the turris-mox-rwtm.ko module on these
boards.
Tested on ESPRESSObin v5 with both default Marvell WTMI firmware and
CZ.NIC's firmware. With default WTMI firmware the turris-mox-rwtm fails
to probe, while with CZ.NIC's firmware it registers the HW random number
generator.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e3850467bf8c82de4a052619136839fe8054b774 ]
Eliminate 1MB gap between Linux and filesystem partitions.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b1dc3c6b3dabbedaf896a3c1a998da191c311c70 ]
Components that rely on proprietary (not to mention signed!) firmware should
not be enabled by default, as lack of the aforementioned firmware could cause
various issues, from random errors to straight-up failing to boot.
Not enabling modem back on the HDK, as it uses a sa8150.
Also fixed a sorting mistake in both boards' dt while at it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210611203301.101067-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dc2f86369b157dfe4dccd31497d2e3c541e7239d ]
The previous one was likely a mistaken copy from pcie1_lane.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210613185334.306225-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dfda1fd16aa71c839e4002109b0cd15f61105ebb ]
enet_clk_ref actually is sourced from internal gpr clocks
which needs a default rate. Also update enet lpcg clock
output names to be more straightforward.
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 15a5261e4d052bf85c7fba24dbe0e9a7c8c05925 ]
This fixes multiple issues with the current non-existent PCIe clock setup:
The controller can run at up to 250MHz, so use a parent that provides this
clock.
The PHY needs an exact 100MHz reference clock to function if the PCIe
refclock is not fed in via the refclock pads. While this mode is not
supported (yet) in the driver it doesn't hurt to make sure we are
providing a clock with the right rate.
The AUX clock is specified to have a maximum clock rate of 10MHz. So
the current setup, which drives it straight from the 25MHz oscillator is
actually overclocking the AUX input.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1de3aa8611d21d6be546ca1cd13ee05bdd650018 ]
The PMIC throws an errors because the clock isn't assigned to it.
Fix this by assigning the clocks info.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8240c972c1798ea013cbb407722295fc826b3584 ]
On LS2088A-RDB board, if the spi-fsl-dspi driver is built as module
then its probe fails with the following warning:
[ 10.471363] couldn't get idr
[ 10.471381] WARNING: CPU: 4 PID: 488 at drivers/spi/spi.c:2689 spi_register_controller+0x73c/0x8d0
...
[ 10.471651] fsl-dspi 2100000.spi: Problem registering DSPI ctlr
[ 10.471708] fsl-dspi: probe of 2100000.spi failed with error -16
Reason for the failure is that bus-num property is set for dspi node.
However, bus-num property is not set for the qspi node. If probe for
spi-fsl-qspi happens first then id 0 is dynamically allocated to it.
Call to spi_register_controller() from spi-fsl-dspi driver then fails.
Since commit 29d2daf2c33c ("spi: spi-fsl-dspi: Make bus-num property
optional") bus-num property is optional. Remove bus-num property from
dspi node to fix the issue.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
memory
[ Upstream commit 8efe01b4386ab38a36b99cfdc1dc02c38a8898c3 ]
The PCIe host bridge on RK3399 advertises a single 64-bit memory
address range even though it lies entirely below 4GB.
Previously the OF PCI range parser treated 64-bit ranges more
leniently (i.e., as 32-bit), but since commit 9d57e61bf723 ("of/pci:
Add IORESOURCE_MEM_64 to resource flags for 64-bit memory addresses")
the code takes a stricter view and treats the ranges as advertised in
the device tree (i.e, as 64-bit).
The change in behaviour causes failure when allocating bus addresses
to devices connected behind a PCI-to-PCI bridge that require
non-prefetchable memory ranges. The allocation failure was observed
for certain Samsung NVMe drives connected to RockPro64 boards.
Update the host bridge window attributes to treat it as 32-bit address
memory. This fixes the allocation failure observed since commit
9d57e61bf723.
Reported-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/7a1e2ebc-f7d8-8431-d844-41a9c36a8911@arm.com
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Tested-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/20210607112856.3499682-5-punitagrawal@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ba5f9b5d7ff3452e69275080c3d59265bc1db8ea ]
Add wakeup delay for fixing PoP noise during capture begin.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/20210513122429.25295-1-srivasam@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 70010556b158a0fefe43415fb0c58347dcce7da0 ]
The SCPI YAML schema expects standard node names for clocks and
power domain controllers. Fix those as per the schema for Juno
platforms.
Link: https://lore.kernel.org/r/20210608145133.2088631-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d4282fb4f8f9683711ae6c076da16aa8e675fdbd ]
Move rmtfs memory region so that it does not overlap with system
RAM (kernel data) when KAsan is enabled. This puts rmtfs right
after mba_mem which is not supposed to increase beyond 0x94600000
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Link: https://lore.kernel.org/r/20210514113430.1.Ic2d032cd80424af229bb95e2c67dd4de1a70cb0c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dc5d91250ae6b810bc8d599d8d6590a06a4ce84a ]
Use sm8250 compatibles instead of sdm845 compatibles
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210329120051.3401567-5-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1dee9e3b0997fef7170f7ea2d8eab47d0cd334d8 ]
Some node unit addresses were put wrongly in the dts, resulting in
below warning when run with W=1
arch/arm64/boot/dts/qcom/sm8350.dtsi:693.34-702.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c222000: simple-bus unit address format error, expected "c263000"
arch/arm64/boot/dts/qcom/sm8350.dtsi:704.34-713.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c223000: simple-bus unit address format error, expected "c265000"
arch/arm64/boot/dts/qcom/sm8350.dtsi:1180.32-1185.5: Warning (simple_bus_reg): /soc@0/interconnect@90e0000: simple-bus unit address format error, expected "90c0000"
Fix by correcting to the correct address as given in reg node
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210513060733.382420-1-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
direction
[ Upstream commit 69db725cdb2b803af67897a08ea54467d11f6020 ]
The MCU RGMII MCU_RGMII1_TXC pin is defined as input by mistake, although
this does not make any difference functionality wise it's better to update
to avoid confusion.
Hence fix MCU RGMII MCU_RGMII1_TXC pin pinmux definitions to be an output
in K3 am654x/j721e/j7200 board files.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210526132041.6104-1-grygorii.strashko@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9e79e58f330ea4860f2ced65a8a35dfb05fc03c1 ]
Populate the device-tree node for the PMU device on Tegra194. This also
fixes the following warning that is observed on booting Tegra194.
ERR KERN kvm: pmu event creation failed -2
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ebc666f39ff67a01e748c34d670ddf05a9e45220 ]
The RZ/G2 boards expect there to be an external clock reference for
USB2 EHCI controllers. For the Beacon boards, this reference clock
is controlled by a programmable versaclock. Because the RZ/G2
family has a special clock driver when using an external clock,
the third clock reference in the EHCI node needs to point to this
special clock, called usb2_clksel.
Since the usb2_clksel does not keep the usb_extal clock enabled,
the 4th clock entry for the EHCI nodes needs to reference it to
keep the clock running and make USB functional.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210513114617.30191-2-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 56bc54496f5d6bc638127bfc9df3742cbf0039e7 ]
The USB extal clock reference isn't associated to a crystal, it's
associated to a programmable clock, so remove the extal reference,
add the usb2_clksel. Since usb_extal is referenced by the versaclock,
reference it here so the usb2_clksel can get the proper clock speed
of 50MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210513114617.30191-1-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|