| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 0ac417b8f124427c90ec8c2ef4f632b821d924cc upstream.
Q7_THRM# pin is connected to a diode on the module which is used
as a level shifter, and the pin have a pull-down enabled by
default. We need to configure it to internal pull-up, other-
wise whenever the pin is configured as INPUT and we try to
control it externally the value will always remain zero.
Signed-off-by: Iskander Amara <iskander.amara@theobroma-systems.com>
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240308085243.69903-1-iskander.amara@theobroma-systems.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ecc3ac293ed15ac2536e9fde2810154486f84010 upstream.
While adding the GIC ITS MSI support, it was found that the msi-map entries
needed to be swapped to receive MSIs from the endpoint.
But later it was identified that the swapping was needed due to a bug in
the Qualcomm PCIe controller driver. And since the bug is now fixed with
commit bf79e33cdd89 ("PCI: qcom: Enable BDF to SID translation properly"),
let's fix the msi-map entries also to reflect the actual mapping in the
hardware.
Cc: stable@vger.kernel.org # 6.3: bf79e33cdd89 ("PCI: qcom: Enable BDF to SID translation properly")
Fixes: ff384ab56f16 ("arm64: dts: qcom: sm8450: Use GIC-ITS for PCIe0 and PCIe1")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240318-pci-bdf-sid-fix-v1-1-acca6c5d9cf1@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8b8ec83a1d7d3b6605d9163d2e306971295a4ce8 upstream.
Add the missing PCIe CX performance level votes to avoid relying on
other drivers (e.g. USB or UFS) to maintain the nominal performance
level required for Gen3 speeds.
Fixes: 813e83157001 ("arm64: dts: qcom: sc8280xp/sa8540p: add PCIe2-4 nodes")
Cc: stable@vger.kernel.org # 6.2
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240306095651.4551-5-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ecda8309098402f878c96184f29a1b7ec682d772 ]
The ACPI DSDT of the Surface Pro X (SQ2) specifies the interrupts for
the secondary UBS controller as
Name (_CRS, ResourceTemplate ()
{
Interrupt (ResourceConsumer, Level, ActiveHigh, Shared, ,, )
{
0x000000AA,
}
Interrupt (ResourceConsumer, Level, ActiveHigh, SharedAndWake, ,, )
{
0x000000A7, // hs_phy_irq: &intc GIC_SPI 136
}
Interrupt (ResourceConsumer, Level, ActiveHigh, SharedAndWake, ,, )
{
0x00000228, // ss_phy_irq: &pdc 40
}
Interrupt (ResourceConsumer, Edge, ActiveHigh, SharedAndWake, ,, )
{
0x0000020A, // dm_hs_phy_irq: &pdc 10
}
Interrupt (ResourceConsumer, Edge, ActiveHigh, SharedAndWake, ,, )
{
0x0000020B, // dp_hs_phy_irq: &pdc 11
}
})
Generally, the interrupts above 0x200 map to the PDC interrupts (as used
in the devicetree) as ACPI_NUMBER - 0x200. Note that this lines up with
dm_hs_phy_irq and dp_hs_phy_irq (as well as the interrupts for the
primary USB controller).
Based on the snippet above, ss_phy_irq should therefore be PDC 40 (=
0x28) and not PDC 7. The latter is according to ACPI instead used as
ss_phy_irq for port 0 of the multiport USB controller). Fix this by
setting ss_phy_irq to '&pdc 40'.
Fixes: b080f53a8f44 ("arm64: dts: qcom: sc8180x: Add remoteprocs, wifi and usb nodes")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20240328022224.336938-1-luzmaximilian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cb939b9b35426852896790aba2f18f46df34e596 ]
The compatible's for the cluster/domain idle states of x1e80100
are wrong, fix it.
Fixes: af16b00578a7 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240317132918.1068817-1-quic_rjendra@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f011688162ec4c492c12ee7cced74c097270baa2 ]
The code in qcom_q6v5_init() requests the "wdog" IRQ as
IRQF_TRIGGER_RISING. If dt defines the interrupt type as LEVEL_HIGH then
the driver will have issues getting the IRQ again after probe deferral
with an error like:
irq: type mismatch, failed to map hwirq-14 for interrupt-controller@b220000!
Fix that by updating the devicetrees to use IRQ_TYPE_EDGE_RISING for
these interrupts, as is already used in most dt's. Also the driver was
already using the interrupts with that type.
Fixes: 3658e411efcb ("arm64: dts: qcom: sc7280: Add ADSP node")
Fixes: df62402e5ff9 ("arm64: dts: qcom: sc7280: Add CDSP node")
Fixes: 152d1faf1e2f ("arm64: dts: qcom: add SC8280XP platform")
Fixes: 8eb5287e8a42 ("arm64: dts: qcom: sm6350: Add CDSP nodes")
Fixes: efc33c969f23 ("arm64: dts: qcom: sm6350: Add ADSP nodes")
Fixes: fe6fd26aeddf ("arm64: dts: qcom: sm6375: Add ADSP&CDSP")
Fixes: 23a8903785b9 ("arm64: dts: qcom: sm8250: Add remoteprocs")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240219-remoteproc-irqs-v1-1-c5aeb02334bd@fairphone.com
[bjorn: Added fixes references]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 433d54818f64a2fe0562f8c04c7a81f562368515 ]
With default dts configuration for BPI-R2Pro, the regulator for sd card is
powered off when reboot is commanded, and the only solution to detect the
sd card again, and therefore, allow rebooting from there, is to do a
hardware reset.
Configure the regulator for sd to be always on for BPI-R2Pro in order to
avoid this issue.
Fixes: f901aaadaa2a ("arm64: dts: rockchip: Add Bananapi R2 Pro")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20240305143222.189413-1-jtornosm@redhat.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
orangepi-5-plus
[ Upstream commit 08cd20bdecd9cfde5c1aec6146fa22ca753efea1 ]
Mark the PMIC as system power controller, so the board will shut-down
properly and fix the typo on rk806_dvs1_null pins property.
Fixes: 236d225e1ee7 ("arm64: dts: rockchip: Add board device tree for rk3588-orangepi-5-plus")
Signed-off-by: Muhammed Efe Cetin <efectn@protonmail.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240407173210.372585-1-efectn@6tel.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3baac7291effb501c4d52df7019ebf52011e5772 ]
1. Fixup infracfg clock controller binding
It also acts as reset controller so #reset-cells is required.
2. Use -pins suffix for pinctrl
This fixes:
arch/arm64/boot/dts/mediatek/mt2712-evb.dtb: syscon@10001000: '#reset-cells' is a required property
from schema $id: http://devicetree.org/schemas/arm/mediatek/mediatek,infracfg.yaml#
arch/arm64/boot/dts/mediatek/mt2712-evb.dtb: pinctrl@1000b000: 'eth_default', 'eth_sleep', 'usb0_iddig', 'usb1_iddig' do not match any of the regexes: 'pinctrl-[0-9]+', 'pins$'
from schema $id: http://devicetree.org/schemas/pinctrl/mediatek,mt65xx-pinctrl.yaml#
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240301074741.8362-1-zajec5@gmail.com
[Angelo: Added Fixes tags]
Fixes: 5d4839709c8e ("arm64: dts: mt2712: Add clock controller device nodes")
Fixes: 1724f4cc5133 ("arm64: dts: Add USB3 related nodes for MT2712")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f8c65a5e4560781f2ea175d8f26cd75ac98e8d78 ]
This fixes:
arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtb: thermal-zones: cpu-thermal:cooling-maps: 'cpu-active-high', 'cpu-active-low', 'cpu-active-med' do not match any of the regexes: '^map[-a-zA-Z0-9]*$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/thermal/thermal-zones.yaml#
Fixes: c26f779a2295 ("arm64: dts: mt7986: add pwm-fan and cooling-maps to BPI-R3 dts")
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240213061459.17917-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 970f8b01bd7719a22e577ba6c78e27f9ccf22783 ]
Thermal block uses only two clocks. Its binding doesn't document or
allow "adc_32k". Also Linux driver doesn't support it.
It has been additionally verified by Angelo by his detailed research on
MT7981 / MT7986 clocks (thanks!).
This fixes:
arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtb: thermal@1100c800: clocks: [[4, 27], [4, 44], [4, 45]] is too long
from schema $id: http://devicetree.org/schemas/thermal/mediatek,thermal.yaml#
arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtb: thermal@1100c800: clock-names: ['therm', 'auxadc', 'adc_32k'] is too long
from schema $id: http://devicetree.org/schemas/thermal/mediatek,thermal.yaml#
Fixes: 0a9615d58d04 ("arm64: dts: mt7986: add thermal and efuse")
Cc: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/linux-devicetree/17d143aa-576e-4d67-a0ea-b79f3518b81c@collabora.com/
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240213053739.14387-3-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3f79e8f3364499750d7442767b101b7bc5864ddf ]
Use order described as preferred in DTS Coding Style:
1. Sort bus nodes by unit address
2. Use alpha-numerical order for the rest
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240212121620.15035-2-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Stable-dep-of: 970f8b01bd77 ("arm64: dts: mediatek: mt7986: drop invalid thermal block clock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9bd88afc94c3570289a0f1c696578b3e1f4e3169 ]
Ethernet block doesn't include or act as a reset controller.
Documentation also doesn't document "#reset-cells" for it.
This fixes:
arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtb: ethernet@15100000: Unevaluated properties are not allowed ('#reset-cells' was unexpected)
from schema $id: http://devicetree.org/schemas/net/mediatek,net.yaml#
Fixes: 082ff36bd5c0 ("arm64: dts: mediatek: mt7986: introduce ethernet nodes")
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240213053739.14387-2-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3b449bfd2ff6c5d3ceecfcb18528ff8e1b4ac2fd ]
Mediatek ethsys controller / syscon binding doesn't allow any subnodes
so "#address-cells" and "#size-cells" are redundant (actually:
disallowed).
This fixes:
arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtb: syscon@15000000: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/clock/mediatek,ethsys.yaml#
Fixes: 1f9986b258c2 ("arm64: dts: mediatek: add clock support for mt7986a")
Cc: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240213053739.14387-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7eb133c99fbebc6adb1cbd22c926d42d2bbca648 ]
Use order described as preferred in DTS Coding Style. Mostly just move
"compatible", "reg" and "ranges" properties. In two nodes also move
vendor-prefixed props down.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240212121620.15035-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Stable-dep-of: 3b449bfd2ff6 ("arm64: dts: mediatek: mt7986: drop invalid properties from ethsys")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ecb5b0034f5bcc35003b4b965cf50c6e98316e79 ]
Binding doesn't specify "reset-names" property and Linux driver also
doesn't use it.
Fix following validation error:
arch/arm64/boot/dts/mediatek/mt7622-rfb1.dtb: thermal@1100b000: Unevaluated properties are not allowed ('reset-names' was unexpected)
from schema $id: http://devicetree.org/schemas/thermal/mediatek,thermal.yaml#
Fixes: ae457b7679c4 ("arm64: dts: mt7622: add SoC and peripheral related device nodes")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317221050.18595-5-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 208add29ce5b7291f6c466e4dfd9cbf61c72888e ]
Fix following validation error:
arch/arm64/boot/dts/mediatek/mt7622-rfb1.dtb: ethernet@1b100000: compatible: ['mediatek,mt7622-eth', 'mediatek,mt2701-eth', 'syscon'] is too long
from schema $id: http://devicetree.org/schemas/net/mediatek,net.yaml#
(and other complains about wrong clocks).
Fixes: 5f599b3a0bb8 ("arm64: dts: mt7622: add ethernet device nodes")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317221050.18595-4-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 800dc93c3941e372c94278bf4059e6e82f60bd66 ]
Fix following validation error:
arch/arm64/boot/dts/mediatek/mt7622-rfb1.dtb: cir@10009000: $nodename:0: 'cir@10009000' does not match '^ir(-receiver)?(@[a-f0-9]+)?$'
from schema $id: http://devicetree.org/schemas/media/mediatek,mt7622-cir.yaml#
Fixes: ae457b7679c4 ("arm64: dts: mt7622: add SoC and peripheral related device nodes")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317221050.18595-3-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3ba5a61594347ab46e7c2cff6cd63ea0f1282efb ]
1. Drop unneeded "syscon"s (bindings were updated recently)
2. Use "clock-controller" in nodenames
3. Add missing "#clock-cells"
Fixes: d7167881e03e ("arm64: dts: mt7622: add clock controller device nodes")
Fixes: e9b65ecb7c30 ("arm64: dts: mediatek: mt7622: introduce nodes for Wireless Ethernet Dispatch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317221050.18595-2-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 296118a8dc297de47d9b3a364b9743f8446bd612 ]
The requested voltage could be lower than the minimum voltage on the
GPU OPP table when the MTK Smart Voltage Scaling (SVS) driver is
enabled, so removing the definition in mt8183-kukui to use the default
minimum voltage (500000 uV) defined in mt6358.dtsi.
Fixes: 31c6732da9d5 ("arm64: dts: mediatek: mt8183-kukui: Override vgpu/vsram_gpu constraints")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240315111621.2263159-4-treapking@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e9a6b8b5c61350535c7eb5ea9b2dde0d5745bd1b ]
Update the minimum voltage from 300000 uV to 400000 uV so it matches
the MT6315 datasheet.
Also update the minimum voltage for Vgpu regulator from 625000 uV to
400000 uV because the requested voltage could be lower than the minimum
voltage on the GPU OPP table when the MTK Smart Voltage Scaling (SVS)
driver is enabled.
Fixes: 260c04d425eb ("arm64: dts: mediatek: cherry: Enable MT6315 regulators on SPMI bus")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240315111621.2263159-3-treapking@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 374a7c6400e314458178255a63c37d6347845092 ]
Update the minimum voltage from 300000 uV to 400000 uV so it matches
the MT6315 datasheet.
Also update the minimum voltage for Vgpu regulator from 606250 uV to
400000 uV because the requested voltage could be lower than the minimum
voltage on the GPU OPP table when the MTK Smart Voltage Scaling (SVS)
driver is enabled.
Fixes: 3183cb62b033 ("arm64: dts: mediatek: asurada: Add SPMI regulators")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240315111621.2263159-2-treapking@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 17b33dd9e4a38fbaca87c68e532b52f9d0492ba7 ]
Describe in each CPU node the regulator supplying it.
Fixes: 260c04d425eb ("arm64: dts: mediatek: cherry: Enable MT6315 regulators on SPMI bus")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240110142305.755367-2-nfraprado@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 58f126296c3c52d02bf3fad1f68c331d718c4a9b ]
Add the missing mediatek,gce-client-reg property to the mutex1 node to
allow it to use the GCE. This prevents the "can't parse gce-client-reg
property" error from being printed and should result in better
performance.
Fixes: 92d2c23dc269 ("arm64: dts: mt8195: add display node for vdosys1")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240229-gce-client-reg-add-missing-mt8192-95-v1-4-b12c233a8a33@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3b129949184a1251e6a42db714f6d68b75fabedd ]
Add the missing mediatek,gce-client-reg property to the mutex node to
allow it to use the GCE. This prevents the "can't parse gce-client-reg
property" error from being printed and should result in better
performance.
Fixes: b852ee68fd72 ("arm64: dts: mt8195: Add display node for vdosys0")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240229-gce-client-reg-add-missing-mt8192-95-v1-3-b12c233a8a33@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 96b0c1528ef41fe754f5d1378b1db6c098a2e33f ]
Add the missing mediatek,gce-client-reg property to the vppsys and
vdosys nodes to allow them to use the GCE. This prevents the "can't
parse gce-client-reg property" error from being printed and should
result in better performance.
Fixes: 6aa5b46d1755 ("arm64: dts: mt8195: Add vdosys and vppsys clock nodes")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240229-gce-client-reg-add-missing-mt8192-95-v1-2-b12c233a8a33@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 00bcc8810d9dd69d3899a4189e2f3964f263a600 ]
Add the missing mediatek,gce-client-reg property to the mutex node to
allow it to use the GCE. This prevents the "can't parse gce-client-reg
property" error from being printed and should result in better
performance.
Fixes: b4b75bac952b ("arm64: dts: mt8192: Add display nodes")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240229-gce-client-reg-add-missing-mt8192-95-v1-1-b12c233a8a33@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1781f2c461804c0123f59afc7350e520a88edffb ]
mfgcfg clock is under MFG_ASYNC power domain.
Fixes: e526c9bc11f8 ("arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and Makefile")
Fixes: 37fb78b9aeb7 ("arm64: dts: mediatek: Add mt8183 power domains controller")
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240223091122.2430037-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 43853e843aa6c3d47ff2b0cce898318839483d05 ]
Remove a redundant node from the Pine64 Pinebook Pro dts, which is intended
to provide a value for the delay in PCI Express enumeration, but that isn't
supported without additional out-of-tree kernel patches.
There were already efforts to upstream those kernel patches, because they
reportedly make some PCI Express cards (such as LSI SAS HBAs) usable in
Pine64 RockPro64 (which is also based on the RK3399); otherwise, those PCI
Express cards fail to enumerate. However, providing the required background
and explanations proved to be a tough nut to crack, which is the reason why
those patches remain outside of the kernel mainline for now.
If those out-of-tree patches eventually become upstreamed, the resulting
device-tree changes will almost surely belong to the RK3399 SoC dtsi. Also,
the above-mentioned unusable-without-out-of-tree-patches PCI Express devices
are in all fairness not usable in a Pinebook Pro without some extensive
hardware modifications, which is another reason to delete this redundant
node. When it comes to the Pinebook Pro, only M.2 NVMe SSDs can be installed
out of the box (using an additional passive adapter PCB sold separately by
Pine64), which reportedly works fine with no additional patches.
Fixes: 5a65505a6988 ("arm64: dts: rockchip: Add initial support for Pinebook Pro")
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/0f82c3f97cb798d012270d13b34d8d15305ef293.1711923520.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 64da060dd4eb625646970d7c96a16de617412ec5 ]
According to the hardware design, the i2c address of audio codec es8316
on Cool Pi CM5 is 0x10.
This fix the read/write error like bellow:
es8316 7-0011: ASoC: error at soc_component_write_no_lock on es8316.7-0011 for register: [0x0000000c] -6
es8316 7-0011: ASoC: error at soc_component_write_no_lock on es8316.7-0011 for register: [0x00000003] -6
es8316 7-0011: ASoC: error at soc_component_read_no_lock on es8316.7-0011 for register: [0x00000016] -6
es8316 7-0011: ASoC: error at soc_component_read_no_lock on es8316.7-0011 for register: [0x00000016] -6
Fixes: 791c154c3982 ("arm64: dts: rockchip: Add support for rk3588 based board Cool Pi CM5 EVB")
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20240324112833.2181961-1-andyshrk@163.com
[also adapted the node name to audio-codec@10]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 945a7c8570916650a415757d15d83e0fa856a686 ]
The PCIE_WAKE# has a diode used as a level-shifter, and is used as an
input pin. While the SoC default is to enable the pull-up, the core
rk3399 pinconf for this pin opted for pull-none. So as to not disturb
the behaviour of other boards which may rely on pull-none instead of
pull-up, set the needed pull-up only for RK3399 Puma.
Fixes: 60fd9f72ce8a ("arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM")
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240308-puma-diode-pu-v2-2-309f83da110a@theobroma-systems.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f0abb4b2c7acf3c3e4130dc3f54cd90cf2ae62bc ]
Nodes overridden by their reference should be ordered alphabetically to
make it easier to read the DTS. pinctrl node is defined in the wrong
location so let's reorder it.
Signed-off-by: Iskander Amara <iskander.amara@theobroma-systems.com>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240308085243.69903-2-iskander.amara@theobroma-systems.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Stable-dep-of: 945a7c857091 ("arm64: dts: rockchip: enable internal pull-up on PCIE_WAKE# for RK3399 Puma")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e6b1168f37e3f86d9966276c5a3fff9eb0df3e5f ]
The Q7_USB_ID has a diode used as a level-shifter, and is used as an
input pin. The SoC default for this pin is a pull-up, which is correct
but the pinconf in the introducing commit missed that, so let's fix this
oversight.
Fixes: ed2c66a95c0c ("arm64: dts: rockchip: fix rk3399-puma-haikou USB OTG mode")
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240308-puma-diode-pu-v2-1-309f83da110a@theobroma-systems.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a2ac2a1b02590a22a236c43c455f421cdede45f5 ]
The MT7531 switch listens on PHY address 0x1f on an MDIO bus. I've got two
findings that support this. There's no bootstrapping option to change the
PHY address of the switch. The Linux driver hardcodes 0x1f as the PHY
address of the switch. So the reg property on the device tree is currently
ignored by the Linux driver.
Therefore, describe the correct PHY address on Banana Pi BPI-R2 Pro that
has this switch.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Fixes: c1804463e5c6 ("arm64: dts: rockchip: Add mt7531 dsa node to BPI-R2-Pro board")
Link: https://lore.kernel.org/r/20240314-for-rockchip-mt7531-phy-address-v1-1-743b5873358f@arinc9.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 50449ca66cc5a8cbc64749cf4b9f3d3fc5f4b457 upstream.
On arm64 machines, swsusp_save() faults if it attempts to access
MEMBLOCK_NOMAP memory ranges. This can be reproduced in QEMU using UEFI
when booting with rodata=off debug_pagealloc=off and CONFIG_KFENCE=n:
Unable to handle kernel paging request at virtual address ffffff8000000000
Mem abort info:
ESR = 0x0000000096000007
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x07: level 3 translation fault
Data abort info:
ISV = 0, ISS = 0x00000007, ISS2 = 0x00000000
CM = 0, WnR = 0, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=00000000eeb0b000
[ffffff8000000000] pgd=180000217fff9803, p4d=180000217fff9803, pud=180000217fff9803, pmd=180000217fff8803, pte=0000000000000000
Internal error: Oops: 0000000096000007 [#1] SMP
Internal error: Oops: 0000000096000007 [#1] SMP
Modules linked in: xt_multiport ipt_REJECT nf_reject_ipv4 xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c iptable_filter bpfilter rfkill at803x snd_hda_codec_hdmi snd_hda_intel snd_intel_dspcfg dwmac_generic stmmac_platform snd_hda_codec stmmac joydev pcs_xpcs snd_hda_core phylink ppdev lp parport ramoops reed_solomon ip_tables x_tables nls_iso8859_1 vfat multipath linear amdgpu amdxcp drm_exec gpu_sched drm_buddy hid_generic usbhid hid radeon video drm_suballoc_helper drm_ttm_helper ttm i2c_algo_bit drm_display_helper cec drm_kms_helper drm
CPU: 0 PID: 3663 Comm: systemd-sleep Not tainted 6.6.2+ #76
Source Version: 4e22ed63a0a48e7a7cff9b98b7806d8d4add7dc0
Hardware name: Greatwall GW-XXXXXX-XXX/GW-XXXXXX-XXX, BIOS KunLun BIOS V4.0 01/19/2021
pstate: 600003c5 (nZCv DAIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : swsusp_save+0x280/0x538
lr : swsusp_save+0x280/0x538
sp : ffffffa034a3fa40
x29: ffffffa034a3fa40 x28: ffffff8000001000 x27: 0000000000000000
x26: ffffff8001400000 x25: ffffffc08113e248 x24: 0000000000000000
x23: 0000000000080000 x22: ffffffc08113e280 x21: 00000000000c69f2
x20: ffffff8000000000 x19: ffffffc081ae2500 x18: 0000000000000000
x17: 6666662074736420 x16: 3030303030303030 x15: 3038666666666666
x14: 0000000000000b69 x13: ffffff9f89088530 x12: 00000000ffffffea
x11: 00000000ffff7fff x10: 00000000ffff7fff x9 : ffffffc08193f0d0
x8 : 00000000000bffe8 x7 : c0000000ffff7fff x6 : 0000000000000001
x5 : ffffffa0fff09dc8 x4 : 0000000000000000 x3 : 0000000000000027
x2 : 0000000000000000 x1 : 0000000000000000 x0 : 000000000000004e
Call trace:
swsusp_save+0x280/0x538
swsusp_arch_suspend+0x148/0x190
hibernation_snapshot+0x240/0x39c
hibernate+0xc4/0x378
state_store+0xf0/0x10c
kobj_attr_store+0x14/0x24
The reason is swsusp_save() -> copy_data_pages() -> page_is_saveable()
-> kernel_page_present() assuming that a page is always present when
can_set_direct_map() is false (all of rodata_full,
debug_pagealloc_enabled() and arm64_kfence_can_set_direct_map() false),
irrespective of the MEMBLOCK_NOMAP ranges. Such MEMBLOCK_NOMAP regions
should not be saved during hibernation.
This problem was introduced by changes to the pfn_valid() logic in
commit a7d9f306ba70 ("arm64: drop pfn_valid_within() and simplify
pfn_valid()").
Similar to other architectures, drop the !can_set_direct_map() check in
kernel_page_present() so that page_is_savable() skips such pages.
Fixes: a7d9f306ba70 ("arm64: drop pfn_valid_within() and simplify pfn_valid()")
Cc: <stable@vger.kernel.org> # 5.14.x
Suggested-by: Mike Rapoport <rppt@kernel.org>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Co-developed-by: xiongxin <xiongxin@kylinos.cn>
Signed-off-by: xiongxin <xiongxin@kylinos.cn>
Signed-off-by: Yaxiong Tian <tianyaxiong@kylinos.cn>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Link: https://lore.kernel.org/r/20240417025248.386622-1-tianyaxiong@kylinos.cn
[catalin.marinas@arm.com: rework commit message]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34e526cb7d46726b2ae5f83f2892d00ebb088509 upstream.
Even though the boot protocol stipulates otherwise, an exception has
been made for the EFI stub, and entering the core kernel with the MMU
enabled is permitted. This allows a substantial amount of cache
maintenance to be elided, wich is significant when fast boot times are
critical (e.g., for booting micro-VMs)
Once the initial ID map has been populated, the MMU is disabled as part
of the logic sequence that puts all system registers into a known state.
Any code that needs to execute within the window where the MMU is off is
cleaned to the PoC explicitly, which includes all of HYP text when
entering at EL2.
However, the current sequence of initializing the EL2 system registers
is not safe: HCR_EL2 is set to its nVHE initial state before SCTLR_EL2
is reprogrammed, and this means that a VHE-to-nVHE switch may occur
while the MMU is enabled. This switch causes some system registers as
well as page table descriptors to be interpreted in a different way,
potentially resulting in spurious exceptions relating to MMU
translation.
So disable the MMU explicitly first when entering in EL2 with the MMU
and caches enabled.
Fixes: 617861703830 ("efi: arm64: enter with MMU and caches enabled")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: <stable@vger.kernel.org> # 6.3.x
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240415075412.2347624-6-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f72b544a514c07d34a0d9d5380f5905b3731e647 upstream.
spi0_lpcg: clock-controller@5a400000 {
... Col0 Col1
clocks = <&clk IMX_SC_R_SPI_0 IMX_SC_PM_CLK_PER>,// 0 1
<&dma_ipg_clk>; // 1 4
clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>;
};
Col1: index, which existing dts try to get.
Col2: actual index in lpcg driver.
lpspi0: spi@5a000000 {
...
clocks = <&spi0_lpcg 0>, <&spi0_lpcg 1>;
^ ^
Should be:
clocks = <&spi0_lpcg IMX_LPCG_CLK_0>, <&spi0_lpcg IMX_LPCG_CLK_4>;
};
Arg0 is divided by 4 in lpcg driver. <&spi0_lpcg 0> and <&spi0_lpcg 1> are
IMX_SC_PM_CLK_PER. Although code can work, code logic is wrong. It should
use IMX_LPCG_CLK_0 and IMX_LPCG_CLK_4 for lpcg arg0.
Cc: stable@vger.kernel.org
Fixes: c4098885e790 ("arm64: dts: imx8dxl: add lpspi support")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d86c2b3946e69d6b0b93568d312aae6247847c0 upstream.
lpcg's arg0 should use clock indices instead of index.
pwm0_lpcg: clock-controller@5d400000 {
... // Col1 Col2
clocks = <&clk IMX_SC_R_PWM_0 IMX_SC_PM_CLK_PER>, // 0 0
<&clk IMX_SC_R_PWM_0 IMX_SC_PM_CLK_PER>, // 1 1
<&clk IMX_SC_R_PWM_0 IMX_SC_PM_CLK_PER>, // 2 4
<&lsio_bus_clk>, // 3 5
<&clk IMX_SC_R_PWM_0 IMX_SC_PM_CLK_PER>; // 4 6
clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>,
<IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>,
<IMX_LPCG_CLK_6>;
};
Col1: index, which existing dts try to get.
Col2: actual index in lpcg driver.
pwm1 {
....
clocks = <&pwm1_lpcg 4>, <&pwm1_lpcg 1>;
^^ ^^
should be:
clocks = <&pwm1_lpcg IMX_LPCG_CLK_6>, <&pwm1_lpcg IMX_LPCG_CLK_1>;
};
Arg0 is divided by 4 in lpcg driver, so index 0 and 1 will be get by pwm
driver, which are same as IMX_LPCG_CLK_6 and IMX_LPCG_CLK_1. Even it can
work, but code logic is wrong. Fixed it by use correct indices.
Cc: stable@vger.kernel.org
Fixes: 23fa99b205ea ("arm64: dts: freescale: imx8-ss-lsio: add support for lsio_pwm0-3")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9055d87bce7276234173fa90e9702af31b3f5353 upstream.
adma_pwm_lpcg: clock-controller@5a590000 {
... col1 col2
clocks = <&clk IMX_SC_R_LCD_0_PWM_0 IMX_SC_PM_CLK_PER>,// 0 0
<&dma_ipg_clk>; // 1 4
clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>;
...
};
Col1: index, which existing dts try to get.
Col2: actual index in lpcg driver.
adma_pwm: pwm@5a190000 {
...
clocks = <&adma_pwm_lpcg 1>, <&adma_pwm_lpcg 0>;
^^ ^^
Should be
clocks = <&adma_pwm_lpcg IMX_LPCG_CLK_4>,
<&adma_pwm_lpcg IMX_LPCG_CLK_0>;
};
Arg0 will be divided by 4 in lcpg driver, so pwm will get IMX_SC_PM_CLK_PER
by <&adma_pwm_lpcg 1>, <&adma_pwm_lpcg 0>. Although function can work, code
logic is wrong. Fix it by use correct indices.
Cc: stable@vger.kernel.org
Fixes: f1d6a6b991ef ("arm64: dts: imx8qxp: add adma_pwm in adma")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 808e7716edcdb39d3498b9f567ef6017858b49aa upstream.
usb2_lpcg: clock-controller@5b270000 {
... Col1 Col2
clocks = <&conn_ahb_clk>, <&conn_ipg_clk>; // 0 6
clock-indices = <IMX_LPCG_CLK_6>, <IMX_LPCG_CLK_7>; // 0 7
...
};
Col1: index, which existing dts try to get.
Col2: actual index in lpcg driver.
usbotg1: usb@5b0d0000 {
...
clocks = <&usb2_lpcg 0>;
^^
Should be:
clocks = <&usb2_lpcg IMX_LPCG_CLK_6>;
};
usbphy1: usbphy@5b100000 {
clocks = <&usb2_lpcg 1>;
^^
SHould be:
clocks = <&usb2_lpcg IMX_LPCG_CLK_7>;
};
Arg0 is divided by 4 in lpcg driver. So lpcg will do dummy enable. Fix it
by use correct clock indices.
Cc: stable@vger.kernel.org
Fixes: 8065fc937f0f ("arm64: dts: imx8dxl: add usb1 and usb2 support")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 81975080f14167610976e968e8016e92d836266f upstream.
adc0_lpcg: clock-controller@5ac80000 {
... Col1 Col2
clocks = <&clk IMX_SC_R_ADC_0 IMX_SC_PM_CLK_PER>, // 0 0
<&dma_ipg_clk>; // 1 4
clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>;
};
Col1: index, which existing dts try to get.
Col2: actual index in lpcg driver.
adc0: adc@5a880000 {
clocks = <&adc0_lpcg 0>, <&adc0_lpcg 1>;
^^ ^^
clocks = <&adc0_lpcg IMX_LPCG_CLK_0>, <&adc0_lpcg IMX_LPCG_CLK_4>;
Arg0 is divided by 4 in lpcg driver. So adc get IMX_SC_PM_CLK_PER by
<&adc0_lpcg 0>, <&adc0_lpcg 1>. Although function can work, code logic is
wrong. Fix it by using correct indices.
Cc: stable@vger.kernel.org
Fixes: 1db044b25d2e ("arm64: dts: imx8dxl: add adc0 support")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0893392334b5dffdf616a53679c6a2942c46391b upstream.
can0_lpcg: clock-controller@5acd0000 {
... Col1 Col2
clocks = <&clk IMX_SC_R_CAN_0 IMX_SC_PM_CLK_PER>, // 0 0
<&dma_ipg_clk>, // 1 4
<&dma_ipg_clk>; // 2 5
clock-indices = <IMX_LPCG_CLK_0>,
<IMX_LPCG_CLK_4>,
<IMX_LPCG_CLK_5>;
}
Col1: index, which existing dts try to get.
Col2: actual index in lpcg driver.
flexcan1: can@5a8d0000 {
clocks = <&can0_lpcg 1>, <&can0_lpcg 0>;
^^ ^^
Should be:
clocks = <&can0_lpcg IMX_LPCG_CLK_4>, <&can0_lpcg IMX_LPCG_CLK_0>;
};
Arg0 is divided by 4 in lpcg driver. flexcan driver get IMX_SC_PM_CLK_PER
by <&can0_lpcg 1> and <&can0_lpcg 0>. Although function can work, code
logic is wrong. Fix it by using correct clock indices.
Cc: stable@vger.kernel.org
Fixes: 5e7d5b023e03 ("arm64: dts: imx8qxp: add flexcan in adma")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 00b436182138310bb8d362b912b12a9df8f72ca3 upstream.
can1_lpcg: clock-controller@5ace0000 {
... Col1 Col2
clocks = <&clk IMX_SC_R_CAN_1 IMX_SC_PM_CLK_PER>,// 0 0
<&dma_ipg_clk>, // 1 4
<&dma_ipg_clk>; // 2 5
clock-indices = <IMX_LPCG_CLK_0>,
<IMX_LPCG_CLK_4>,
<IMX_LPCG_CLK_5>;
};
Col1: index, which existing dts try to get.
Col2: actual index in lpcg driver
&flexcan2 {
clocks = <&can1_lpcg 1>, <&can1_lpcg 0>;
^^ ^^
Should be:
clocks = <&can1_lpcg IMX_LPCG_CLK_4>, <&can1_lpcg IMX_LPCG_CLK_0>;
};
Arg0 is divided by 4 in lpcg driver. So flexcan get IMX_SC_PM_CLK_PER by
<&can1_lpcg 1> and <&can1_lpcg 0>. Although function work, code logic is
wrong. Fix it by using correct clock indices.
Cc: stable@vger.kernel.org
Fixes: be85831de020 ("arm64: dts: imx8qm: add can node in devicetree")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c6ddd6e7b166532a0816825442ff60f70aed9647 ]
The actual clock show wrong frequency:
echo on >/sys/devices/platform/bus\@5b000000/5b010000.mmc/power/control
cat /sys/kernel/debug/mmc0/ios
clock: 200000000 Hz
actual clock: 166000000 Hz
^^^^^^^^^
.....
According to
sdhc0_lpcg: clock-controller@5b200000 {
compatible = "fsl,imx8qxp-lpcg";
reg = <0x5b200000 0x10000>;
#clock-cells = <1>;
clocks = <&clk IMX_SC_R_SDHC_0 IMX_SC_PM_CLK_PER>,
<&conn_ipg_clk>, <&conn_axi_clk>;
clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>,
<IMX_LPCG_CLK_5>;
clock-output-names = "sdhc0_lpcg_per_clk",
"sdhc0_lpcg_ipg_clk",
"sdhc0_lpcg_ahb_clk";
power-domains = <&pd IMX_SC_R_SDHC_0>;
}
"per_clk" should be IMX_LPCG_CLK_0 instead of IMX_LPCG_CLK_5.
After correct clocks order:
echo on >/sys/devices/platform/bus\@5b000000/5b010000.mmc/power/control
cat /sys/kernel/debug/mmc0/ios
clock: 200000000 Hz
actual clock: 198000000 Hz
^^^^^^^^
...
Fixes: 16c4ea7501b1 ("arm64: dts: imx8: switch to new lpcg clock binding")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6f8e0aca838e163e81fde176e945161d50679339 ]
When using usb-conn-gpio to control USB role and VBUS, the vbus-supply
property must be present in the usb-conn-gpio node. Additionally it
should not be present in the phy node as that isn't what controls vbus
and will upset the use count.
This resolves an issue where VBUS is enabled with OTG in peripheral
mode.
Fixes: ad9a12f7a522 ("arm64: dts: imx8mp-venice: Fix USB connector description")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8cb10cba124c4798b6cb333245ecdc8dde78aeae ]
When using usb-conn-gpio to control USB role and VBUS, the vbus-supply
property must be present in the usb-conn-gpio node. Additionally it
should not be present in the phy node as that isn't what controls vbus
and will upset the use count.
This resolves an issue where VBUS is enabled with OTG in peripheral
mode.
Fixes: ad9a12f7a522 ("arm64: dts: imx8mp-venice: Fix USB connector description")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e3ba51ab24fddef79fc212f9840de54db8fd1685 upstream.
KVM/arm64 relies on TLBI RANGE feature to flush TLBs when the dirty
pages are collected by VMM and the page table entries become write
protected during live migration. Unfortunately, the operand passed
to the TLBI RANGE instruction isn't correctly sorted out due to the
commit 117940aa6e5f ("KVM: arm64: Define kvm_tlb_flush_vmid_range()").
It leads to crash on the destination VM after live migration because
TLBs aren't flushed completely and some of the dirty pages are missed.
For example, I have a VM where 8GB memory is assigned, starting from
0x40000000 (1GB). Note that the host has 4KB as the base page size.
In the middile of migration, kvm_tlb_flush_vmid_range() is executed
to flush TLBs. It passes MAX_TLBI_RANGE_PAGES as the argument to
__kvm_tlb_flush_vmid_range() and __flush_s2_tlb_range_op(). SCALE#3
and NUM#31, corresponding to MAX_TLBI_RANGE_PAGES, isn't supported
by __TLBI_RANGE_NUM(). In this specific case, -1 has been returned
from __TLBI_RANGE_NUM() for SCALE#3/2/1/0 and rejected by the loop
in the __flush_tlb_range_op() until the variable @scale underflows
and becomes -9, 0xffff708000040000 is set as the operand. The operand
is wrong since it's sorted out by __TLBI_VADDR_RANGE() according to
invalid @scale and @num.
Fix it by extending __TLBI_RANGE_NUM() to support the combination of
SCALE#3 and NUM#31. With the changes, [-1 31] instead of [-1 30] can
be returned from the macro, meaning the TLBs for 0x200000 pages in the
above example can be flushed in one shoot with SCALE#3 and NUM#31. The
macro TLBI_RANGE_MASK is dropped since no one uses it any more. The
comments are also adjusted accordingly.
Fixes: 117940aa6e5f ("KVM: arm64: Define kvm_tlb_flush_vmid_range()")
Cc: stable@kernel.org # v6.6+
Reported-by: Yihuang Yu <yihyu@redhat.com>
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Link: https://lore.kernel.org/r/20240405035852.1532010-2-gshan@redhat.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7c6bef576a8891abce08d448165b53328032aa5f ]
The SC7280 GCC binding describes clocks which, due to the difference in
security model, are not accessible on the RB3gen2 - in the same way seen
on QCM6490.
Mark these clocks as protected, to allow the board to boot. In contrast
to the present QCM6490 boards GCC_EDP_CLKREF_EN is left out, as this
does not need to be "protected" and is used on the RB3Gen2 board.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240209-qcm6490-gcc-protected-clocks-v2-1-11cd5fc13bd0@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f051b6ace7ffcc48d6d1017191f167c0a85799f6 ]
Fix rk3399 hdmi ports node so that it matches the
rockchip,dw-hdmi.yaml binding.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/a6ab6f75-3b80-40b1-bd30-3113e14becdd@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1d00ba4700d1e0f88ae70d028d2e17e39078fa1c ]
Fix rk3328 hdmi ports node so that it matches the
rockchip,dw-hdmi.yaml binding.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/e5dea3b7-bf84-4474-9530-cc2da3c41104@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
