| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit bbe28fc3cbabbef781bcdf847615d52ce2e26e42 ]
hi3660-hikey960.dts:
Define a 'ports' node for 'adv7533: adv7533@39' and the
'adi,dsi-lanes' property to make it compliant with the adi,adv7533 DT
binding.
This fills the requirements to meet the binding requirements,
remote endpoints are not defined.
hi6220-hikey.dts:
Change property name s/pd-gpio/pd-gpios, gpio properties should be
plural. This is just a cosmetic change.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b072714bfc0e42c984b8fd6e069f3ca17de8137a ]
Once regulators are disabled after kernel boot, on Espresso board silent
hang observed because of LDO7 being disabled. LDO7 actually provide
power to CPU cores and non-cpu blocks circuitries. Keep this regulator
always-on to fix this hang.
Fixes: 9589f7721e16 ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1b6a1a162defe649c5599d661b58ac64bb6f31b6 ]
msm8916-pins.dtsi specifies "bias-pull-none" for most of the audio
pin configurations. This was likely copied from the qcom kernel fork
where the same property was used for these audio pins.
However, "bias-pull-none" actually does not exist at all - not in
mainline and not in downstream. I can only guess that the original
intention was to configure "no pull", i.e. bias-disable.
Change it to that instead.
Fixes: 143bb9ad85b7 ("arm64: dts: qcom: add audio pinctrls")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200605185916.318494-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a445086f8af0b7b9bd8d1901d6f306bb154f70d ]
The puma gmac node currently uses opposite active-values for the
gmac phy reset pin. The gpio-declaration uses active-high while the
separate snps,reset-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
other Rockchip board.
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7a7184f6cfa9279f1a1c10a1845d247d7fad54ff ]
The puma vcc5v0_host regulator node currently uses opposite active-values
for the enable pin. The gpio-declaration uses active-high while the
separate enable-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
gmac fix.
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 05fb3dbda187bbd9cc1cd0e97e5d6595af570ac6 ]
Although iph is expected to point to at least 20 bytes of valid memory,
ihl may be bogus, for example on reception of a corrupt packet. If it
happens to be less than 5, we really don't want to run away and
dereference 16GB worth of memory until it wraps back to exactly zero...
Fixes: 0e455d8e80aa ("arm64: Implement optimised IP checksum helpers")
Reported-by: guodeqing <geffrey.guo@huawei.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 966a0acce2fca776391823381dba95c40e03c339 ]
Commit f7b93d42945c ("arm64/alternatives: use subsections for replacement
sequences") breaks LLVM's integrated assembler, because due to its
one-pass design, it cannot compute instruction sequence lengths before the
layout for the subsection has been finalized. This change fixes the build
by moving the .org directives inside the subsection, so they are processed
after the subsection layout is known.
Fixes: f7b93d42945c ("arm64/alternatives: use subsections for replacement sequences")
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1078
Link: https://lore.kernel.org/r/20200730153701.3892953-1-samitolvanen@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5afc78551bf5d53279036e0bf63314e35631d79f ]
Rather than open-code test_tsk_thread_flag() at each callsite, simply
replace the couple of offenders with calls to test_tsk_thread_flag()
directly.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3a5a4366cecc25daa300b9a9174f7fdd352b9068 upstream.
Luis reports that, when reverse debugging with GDB, single-step does not
function as expected on arm64:
| I've noticed, under very specific conditions, that a PTRACE_SINGLESTEP
| request by GDB won't execute the underlying instruction. As a consequence,
| the PC doesn't move, but we return a SIGTRAP just like we would for a
| regular successful PTRACE_SINGLESTEP request.
The underlying problem is that when the CPU register state is restored
as part of a reverse step, the SPSR.SS bit is cleared and so the hardware
single-step state can transition to the "active-pending" state, causing
an unexpected step exception to be taken immediately if a step operation
is attempted.
In hindsight, we probably shouldn't have exposed SPSR.SS in the pstate
accessible by the GPR regset, but it's a bit late for that now. Instead,
simply prevent userspace from configuring the bit to a value which is
inconsistent with the TIF_SINGLESTEP state for the task being traced.
Cc: <stable@vger.kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Keno Fischer <keno@juliacomputing.com>
Link: https://lore.kernel.org/r/1eed6d69-d53d-9657-1fc9-c089be07f98c@linaro.org
Reported-by: Luis Machado <luis.machado@linaro.org>
Tested-by: Luis Machado <luis.machado@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 95ca6f06dd4827ff63be5154120c7a8511cd9a41 ]
The peripheral clock of the RNG is missing for gxl while it is present
for gxbb.
Fixes: 1b3f6d148692 ("ARM64: dts: meson-gx: add clock CLKID_RNG0 to hwrng node")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200617125346.1163527-1-jbrunet@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5679b28142193a62f6af93249c0477be9f0c669b ]
Commit f7b93d42945c ("arm64/alternatives: use subsections for replacement
sequences") moved the alternatives replacement sequences into subsections,
in order to keep the as close as possible to the code that they replace.
Unfortunately, this broke the logic in branch_insn_requires_update,
which assumed that any branch into kernel executable code was a branch
that required updating, which is no longer the case now that the code
sequences that are patched in are in the same section as the patch site
itself.
So the only way to discriminate branches that require updating and ones
that don't is to check whether the branch targets the replacement sequence
itself, and so we can drop the call to kernel_text_address() entirely.
Fixes: f7b93d42945c ("arm64/alternatives: use subsections for replacement sequences")
Reported-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/20200709125953.30918-1-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3c4d9137eefecf273a520d392071ffc9df0a9a7a ]
Return statements in functions returning bool should use true or false
instead of an integer value. This code was detected with the help of
Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f7b93d42945cc71e1346dd5ae07c59061d56745e ]
When building very large kernels, the logic that emits replacement
sequences for alternatives fails when relative branches are present
in the code that is emitted into the .altinstr_replacement section
and patched in at the original site and fixed up. The reason is that
the linker will insert veneers if relative branches go out of range,
and due to the relative distance of the .altinstr_replacement from
the .text section where its branch targets usually live, veneers
may be emitted at the end of the .altinstr_replacement section, with
the relative branches in the sequence pointed at the veneers instead
of the actual target.
The alternatives patching logic will attempt to fix up the branch to
point to its original target, which will be the veneer in this case,
but given that the patch site is likely to be far away as well, it
will be out of range and so patching will fail. There are other cases
where these veneers are problematic, e.g., when the target of the
branch is in .text while the patch site is in .init.text, in which
case putting the replacement sequence inside .text may not help either.
So let's use subsections to emit the replacement code as closely as
possible to the patch site, to ensure that veneers are only likely to
be emitted if they are required at the patch site as well, in which
case they will be in range for the replacement sequence both before
and after it is transported to the patch site.
This will prevent alternative sequences in non-init code from being
released from memory after boot, but this is tolerable given that the
entire section is only 512 KB on an allyesconfig build (which weighs in
at 500+ MB for the entire Image). Also, note that modules today carry
the replacement sequences in non-init sections as well, and any of
those that target init code will be emitted into init sections after
this change.
This fixes an early crash when booting an allyesconfig kernel on a
system where any of the alternatives sequences containing relative
branches are activated at boot (e.g., ARM64_HAS_PAN on TX2)
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Dave P Martin <dave.martin@arm.com>
Link: https://lore.kernel.org/r/20200630081921.13443-1-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b9e10d4a6c9f5cbe6369ce2c17ebc67d2e5a4be5 upstream.
HVC_SOFT_RESTART is given values for x0-2 that it should installed
before exiting to the new address so should not set x0 to stub HVC
success or failure code.
Fixes: af42f20480bf1 ("arm64: hyp-stub: Zero x0 on successful stub handling")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Scull <ascull@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200706095259.1338221-1-ascull@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 68cf617309b5f6f3a651165f49f20af1494753ae upstream.
PAGE_HYP_DEVICE is intended to encode attribute bits for an EL2 stage-1
pte mapping a device. Unfortunately, it includes PROT_DEVICE_nGnRE which
encodes attributes for EL1 stage-1 mappings such as UXN and nG, which are
RES0 for EL2, and DBM which is meaningless as TCR_EL2.HD is not set.
Fix the definition of PAGE_HYP_DEVICE so that it doesn't set RES0 bits
at EL2.
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200708162546.26176-1-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8523c006264df65aac7d77284cc69aac46a6f842 ]
After entering kdb due to breakpoint, when we execute 'ss' or 'go' (will
delay installing breakpoints, do single-step first), it won't work
correctly, and it will enter kdb due to oops.
It's because the reason gotten in kdb_stub() is not as expected, and it
seems that the ex_vector for single-step should be 0, like what arch
powerpc/sh/parisc has implemented.
Before the patch:
Entering kdb (current=0xffff8000119e2dc0, pid 0) on processor 0 due to Keyboard Entry
[0]kdb> bp printk
Instruction(i) BP #0 at 0xffff8000101486cc (printk)
is enabled addr at ffff8000101486cc, hardtype=0 installed=0
[0]kdb> g
/ # echo h > /proc/sysrq-trigger
Entering kdb (current=0xffff0000fa878040, pid 266) on processor 3 due to Breakpoint @ 0xffff8000101486cc
[3]kdb> ss
Entering kdb (current=0xffff0000fa878040, pid 266) on processor 3 Oops: (null)
due to oops @ 0xffff800010082ab8
CPU: 3 PID: 266 Comm: sh Not tainted 5.7.0-rc4-13839-gf0e5ad491718 #6
Hardware name: linux,dummy-virt (DT)
pstate: 00000085 (nzcv daIf -PAN -UAO)
pc : el1_irq+0x78/0x180
lr : __handle_sysrq+0x80/0x190
sp : ffff800015003bf0
x29: ffff800015003d20 x28: ffff0000fa878040
x27: 0000000000000000 x26: ffff80001126b1f0
x25: ffff800011b6a0d8 x24: 0000000000000000
x23: 0000000080200005 x22: ffff8000101486cc
x21: ffff800015003d30 x20: 0000ffffffffffff
x19: ffff8000119f2000 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000
x9 : 0000000000000000 x8 : ffff800015003e50
x7 : 0000000000000002 x6 : 00000000380b9990
x5 : ffff8000106e99e8 x4 : ffff0000fadd83c0
x3 : 0000ffffffffffff x2 : ffff800011b6a0d8
x1 : ffff800011b6a000 x0 : ffff80001130c9d8
Call trace:
el1_irq+0x78/0x180
printk+0x0/0x84
write_sysrq_trigger+0xb0/0x118
proc_reg_write+0xb4/0xe0
__vfs_write+0x18/0x40
vfs_write+0xb0/0x1b8
ksys_write+0x64/0xf0
__arm64_sys_write+0x14/0x20
el0_svc_common.constprop.2+0xb0/0x168
do_el0_svc+0x20/0x98
el0_sync_handler+0xec/0x1a8
el0_sync+0x140/0x180
[3]kdb>
After the patch:
Entering kdb (current=0xffff8000119e2dc0, pid 0) on processor 0 due to Keyboard Entry
[0]kdb> bp printk
Instruction(i) BP #0 at 0xffff8000101486cc (printk)
is enabled addr at ffff8000101486cc, hardtype=0 installed=0
[0]kdb> g
/ # echo h > /proc/sysrq-trigger
Entering kdb (current=0xffff0000fa852bc0, pid 268) on processor 0 due to Breakpoint @ 0xffff8000101486cc
[0]kdb> g
Entering kdb (current=0xffff0000fa852bc0, pid 268) on processor 0 due to Breakpoint @ 0xffff8000101486cc
[0]kdb> ss
Entering kdb (current=0xffff0000fa852bc0, pid 268) on processor 0 due to SS trap @ 0xffff800010082ab8
[0]kdb>
Fixes: 44679a4f142b ("arm64: KGDB: Add step debugging support")
Signed-off-by: Wei Li <liwei391@huawei.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200509214159.19680-2-liwei391@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8dfe804a4031ca6ba3a3efb2048534249b64f3a5 upstream.
A 32-bit perf querying the registers of a compat task using REGS_ABI_32
will receive zeroes from w15, when it expects to find the PC.
Return the PC value for register dwarf register 15 when returning register
values for a compat task to perf.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Jiping Ma <jiping.ma2@windriver.com>
Link: https://lore.kernel.org/r/1589165527-188401-1-git-send-email-jiping.ma2@windriver.com
[will: Shuffled code and added a comment]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 24ebec25fb270100e252b19c288e21bd7d8cc7f7 ]
Unprivileged memory accesses generated by the so-called "translated"
instructions (e.g. STTR) at EL1 can cause EL0 watchpoints to fire
unexpectedly if kernel debugging is enabled. In such cases, the
hw_breakpoint logic will invoke the user overflow handler which will
typically raise a SIGTRAP back to the current task. This is futile when
returning back to the kernel because (a) the signal won't have been
delivered and (b) userspace can't handle the thing anyway.
Avoid invoking the user overflow handler for watchpoints triggered by
kernel uaccess routines, and instead single-step over the faulting
instruction as we would if no overflow handler had been installed.
(Fixes tag identifies the introduction of unprivileged memory accesses,
which exposed this latent bug in the hw_breakpoint code)
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Fixes: 57f4959bad0a ("arm64: kernel: Add support for User Access Override")
Reported-by: Luis Machado <luis.machado@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3204be4109ad681523e3461ce64454c79278450a upstream.
AArch32 CP1x registers are overlayed on their AArch64 counterparts
in the vcpu struct. This leads to an interesting problem as they
are stored in their CPU-local format, and thus a CP1x register
doesn't "hit" the lower 32bit portion of the AArch64 register on
a BE host.
To workaround this unfortunate situation, introduce a bias trick
in the vcpu_cp1x() accessors which picks the correct half of the
64bit register.
Cc: stable@vger.kernel.org
Reported-by: James Morse <james.morse@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c604fd810bda667bdc20b2c041917baa7803e0fb ]
Dts files with Rockchip rk3399 'gpu' nodes were manually verified.
In order to automate this process arm,mali-midgard.txt
has been converted to yaml. In the new setup dtbs_check with
arm,mali-midgard.yaml expects interrupts and interrupt-names values
in the same order. Fix this for rk3399.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/gpu/
arm,mali-midgard.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425143837.18706-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Commit d51c214541c5154dda3037289ee895ea3ded5ebd upstream.
The second argument is the end "pointer", not the length.
Fixes: d28f6df1305a ("arm64/kexec: Add core kexec support")
Cc: <stable@vger.kernel.org> # 4.8.x-
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 190c7f6fd43a776d4a6da1dac44408104649e9b7 upstream.
The device tree compiler complains that the dwc3 nodes have regs
properties but no matching unit addresses.
Add the unit addresses to the device node name. While at it, also rename
the nodes from "dwc3" to "usb", as guidelines require device nodes have
generic names.
Fixes: 7144224f2c2b ("arm64: dts: rockchip: support dwc3 USB for rk3399")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200327030414.5903-7-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83b994129fb4c18a8460fd395864a28740e5e7fb upstream.
In some board device tree files, "rk805" was used for the RK805 PMIC's
node name. However the policy for device trees is that generic names
should be used.
Replace the "rk805" node name with the generic "pmic" name.
Fixes: 1e28037ec88e ("arm64: dts: rockchip: add rk805 node for rk3328-evb")
Fixes: 955bebde057e ("arm64: dts: rockchip: add rk3328-rock64 board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200327030414.5903-3-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c9a4ef66450145a356a626c833d3d7b1668b3ded ]
In assembly, many instances of __emit_inst(x) expand to a directive. In
a few places __emit_inst(x) is used as an assembler macro argument. For
example, in arch/arm64/kvm/hyp/entry.S
ALTERNATIVE(nop, SET_PSTATE_PAN(1), ARM64_HAS_PAN, CONFIG_ARM64_PAN)
expands to the following by the C preprocessor:
alternative_insn nop, .inst (0xd500401f | ((0) << 16 | (4) << 5) | ((!!1) << 8)), 4, 1
Both comma and space are separators, with an exception that content
inside a pair of parentheses/quotes is not split, so the clang
integrated assembler splits the arguments to:
nop, .inst, (0xd500401f | ((0) << 16 | (4) << 5) | ((!!1) << 8)), 4, 1
GNU as preprocesses the input with do_scrub_chars(). Its arm64 backend
(along with many other non-x86 backends) sees:
alternative_insn nop,.inst(0xd500401f|((0)<<16|(4)<<5)|((!!1)<<8)),4,1
# .inst(...) is parsed as one argument
while its x86 backend sees:
alternative_insn nop,.inst (0xd500401f|((0)<<16|(4)<<5)|((!!1)<<8)),4,1
# The extra space before '(' makes the whole .inst (...) parsed as two arguments
The non-x86 backend's behavior is considered unintentional
(https://sourceware.org/bugzilla/show_bug.cgi?id=25750).
So drop the space separator inside `.inst (...)` to make the clang
integrated assembler work.
Suggested-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Fangrui Song <maskray@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/939
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a25ffd3a6302a67814280274d8f1aa4ae2ea4b59 ]
Printing raw pointer values in backtraces has potential security
implications and are of questionable value anyway.
This patch follows x86's lead and removes the "Exception stack:" dump
from kernel backtraces, as well as converting PC/LR values to symbols
such as "sysrq_handle_crash+0x20/0x30".
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f8ada189550984ee21f27be736042b74a7da1d68 ]
bus access read/write events are not supported in A73, based on the
Cortex-A73 TRM r0p2, section 11.9 Events (pages 11-457 to 11-460).
Fixes: 5561b6c5e981 "arm64: perf: add support for Cortex-A73"
Acked-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Xu YiPing <xuyiping@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fc2266011accd5aeb8ebc335c381991f20e26e33 upstream.
For thumb instructions, call_undef_hook() in traps.c first reads a u16,
and if the u16 indicates a T32 instruction (u16 >= 0xe800), a second
u16 is read, which then makes up the the lower half-word of a T32
instruction. For T16 instructions, the second u16 is not read,
which makes the resulting u32 opcode always have the upper half set to
0.
However, having the upper half of instr_mask in the undef_hook set to 0
masks out the upper half of all thumb instructions - both T16 and T32.
This results in trapped T32 instructions with the lower half-word equal
to the T16 encoding of setend (b650) being matched, even though the upper
half-word is not 0000 and thus indicates a T32 opcode.
An example of such a T32 instruction is eaa0b650, which should raise a
SIGILL since T32 instructions with an eaa prefix are unallocated as per
Arm ARM, but instead works as a SETEND because the second half-word is set
to b650.
This patch fixes the issue by extending instr_mask to include the
upper u32 half, which will still match T16 instructions where the upper
half is 0, but not T32 instructions.
Fixes: 2d888f48e056 ("arm64: Emulate SETEND for AArch32 tasks")
Cc: <stable@vger.kernel.org> # 4.0.x-
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Fredrik Strupe <fredrik@strupe.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 61cf61d81e326163ce1557ceccfca76e11d0e57c upstream.
__early_cpu_boot_status is of type long. Use quad
assembler directive to allocate proper size.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arun KS <arunks@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d79e9d7c1e4ba5f95f2ff3541880c40ea9722212 upstream.
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: 3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4022d808c45277693ea86478fab1f081ebf997e8 upstream.
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: bf02f2ffe59c ("arm64: dts: add LS1043A DPAA FMan support")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f5459da2b8736720afdbd67c4bd2d1edba7d0e3 upstream.
Building an arm64 defconfig with clang's integrated assembler, this error
occurs:
<instantiation>:2:2: error: unrecognized instruction mnemonic
_ASM_EXTABLE 9999b, 9f
^
arch/arm64/mm/cache.S:50:1: note: while in macro instantiation
user_alt 9f, "dc cvau, x4", "dc civac, x4", 0
^
While GNU as seems fine with case-sensitive macro instantiations, clang
doesn't, so use the actual macro name (_asm_extable) as in the rest of
the file.
Also checked that the generated assembly matches the GCC output.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Fixes: 290622efc76e ("arm64: fix "dc cvau" cache operation on errata-affected core")
Link: https://github.com/ClangBuiltLinux/linux/issues/924
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 25dc2c80cfa33153057aa94984855acd57adf92a upstream.
The SPSR_ELx format for exceptions taken from AArch32 differs from the
AArch32 PSR format. Thus, we must translate between the two when setting
up a compat sigframe, or restoring context from a compat sigframe.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: 7206dc93a58fb764 ("arm64: Expose Arm v8.4 features")
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 76fc52bd07d3e9cb708f1a50b60c825c96acd606 upstream.
The SPSR_ELx format for exceptions taken from AArch32 is slightly
different to the AArch32 PSR format.
Map between the two in the compat ptrace code.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: 7206dc93a58fb764 ("arm64: Expose Arm v8.4 features")
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b54d3900862374e1bb2846e6b39d79c896c0b200 ]
The LS1043A SoC is affected by the A050385 erratum stating that
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak thus stopping further packet processing.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f50b7dacccbab2b9e3ef18f52a6dcc18ed2050b9 upstream.
On a system configured to trigger a crash_kexec() reboot, when only one CPU
is online and another CPU panics while starting-up, crash_smp_send_stop()
will fail to send any STOP message to the other already online core,
resulting in fail to freeze and registers not properly saved.
Moreover even if the proper messages are sent (case CPUs > 2)
it will similarly fail to account for the booting CPU when executing
the final stop wait-loop, so potentially resulting in some CPU not
been waited for shutdown before rebooting.
A tangible effect of this behaviour can be observed when, after a panic
with kexec enabled and loaded, on the following reboot triggered by kexec,
the cpu that could not be successfully stopped fails to come back online:
[ 362.291022] ------------[ cut here ]------------
[ 362.291525] kernel BUG at arch/arm64/kernel/cpufeature.c:886!
[ 362.292023] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 362.292400] Modules linked in:
[ 362.292970] CPU: 3 PID: 0 Comm: swapper/3 Kdump: loaded Not tainted 5.6.0-rc4-00003-gc780b890948a #105
[ 362.293136] Hardware name: Foundation-v8A (DT)
[ 362.293382] pstate: 200001c5 (nzCv dAIF -PAN -UAO)
[ 362.294063] pc : has_cpuid_feature+0xf0/0x348
[ 362.294177] lr : verify_local_elf_hwcaps+0x84/0xe8
[ 362.294280] sp : ffff800011b1bf60
[ 362.294362] x29: ffff800011b1bf60 x28: 0000000000000000
[ 362.294534] x27: 0000000000000000 x26: 0000000000000000
[ 362.294631] x25: 0000000000000000 x24: ffff80001189a25c
[ 362.294718] x23: 0000000000000000 x22: 0000000000000000
[ 362.294803] x21: ffff8000114aa018 x20: ffff800011156a00
[ 362.294897] x19: ffff800010c944a0 x18: 0000000000000004
[ 362.294987] x17: 0000000000000000 x16: 0000000000000000
[ 362.295073] x15: 00004e53b831ae3c x14: 00004e53b831ae3c
[ 362.295165] x13: 0000000000000384 x12: 0000000000000000
[ 362.295251] x11: 0000000000000000 x10: 00400032b5503510
[ 362.295334] x9 : 0000000000000000 x8 : ffff800010c7e204
[ 362.295426] x7 : 00000000410fd0f0 x6 : 0000000000000001
[ 362.295508] x5 : 00000000410fd0f0 x4 : 0000000000000000
[ 362.295592] x3 : 0000000000000000 x2 : ffff8000100939d8
[ 362.295683] x1 : 0000000000180420 x0 : 0000000000180480
[ 362.296011] Call trace:
[ 362.296257] has_cpuid_feature+0xf0/0x348
[ 362.296350] verify_local_elf_hwcaps+0x84/0xe8
[ 362.296424] check_local_cpu_capabilities+0x44/0x128
[ 362.296497] secondary_start_kernel+0xf4/0x188
[ 362.296998] Code: 52805001 72a00301 6b01001f 54000ec0 (d4210000)
[ 362.298652] SMP: stopping secondary CPUs
[ 362.300615] Starting crashdump kernel...
[ 362.301168] Bye!
[ 0.000000] Booting Linux on physical CPU 0x0000000003 [0x410fd0f0]
[ 0.000000] Linux version 5.6.0-rc4-00003-gc780b890948a (crimar01@e120937-lin) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #105 SMP PREEMPT Fri Mar 6 17:00:42 GMT 2020
[ 0.000000] Machine model: Foundation-v8A
[ 0.000000] earlycon: pl11 at MMIO 0x000000001c090000 (options '')
[ 0.000000] printk: bootconsole [pl11] enabled
.....
[ 0.138024] rcu: Hierarchical SRCU implementation.
[ 0.153472] its@2f020000: unable to locate ITS domain
[ 0.154078] its@2f020000: Unable to locate ITS domain
[ 0.157541] EFI services will not be available.
[ 0.175395] smp: Bringing up secondary CPUs ...
[ 0.209182] psci: failed to boot CPU1 (-22)
[ 0.209377] CPU1: failed to boot: -22
[ 0.274598] Detected PIPT I-cache on CPU2
[ 0.278707] GICv3: CPU2: found redistributor 1 region 0:0x000000002f120000
[ 0.285212] CPU2: Booted secondary processor 0x0000000001 [0x410fd0f0]
[ 0.369053] Detected PIPT I-cache on CPU3
[ 0.372947] GICv3: CPU3: found redistributor 2 region 0:0x000000002f140000
[ 0.378664] CPU3: Booted secondary processor 0x0000000002 [0x410fd0f0]
[ 0.401707] smp: Brought up 1 node, 3 CPUs
[ 0.404057] SMP: Total of 3 processors activated.
Make crash_smp_send_stop() account also for the online status of the
calling CPU while evaluating how many CPUs are effectively online: this way
the right number of STOPs is sent and all other stopped-cores's registers
are properly saved.
Fixes: 78fd584cdec05 ("arm64: kdump: implement machine_crash_shutdown()")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d0bab0c39e32d39a8c5cddca72e5b4a3059fe050 upstream.
On a system with only one CPU online, when another one CPU panics while
starting-up, smp_send_stop() will fail to send any STOP message to the
other already online core, resulting in a system still responsive and
alive at the end of the panic procedure.
[ 186.700083] CPU3: shutdown
[ 187.075462] CPU2: shutdown
[ 187.162869] CPU1: shutdown
[ 188.689998] ------------[ cut here ]------------
[ 188.691645] kernel BUG at arch/arm64/kernel/cpufeature.c:886!
[ 188.692079] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 188.692444] Modules linked in:
[ 188.693031] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 5.6.0-rc4-00001-g338d25c35a98 #104
[ 188.693175] Hardware name: Foundation-v8A (DT)
[ 188.693492] pstate: 200001c5 (nzCv dAIF -PAN -UAO)
[ 188.694183] pc : has_cpuid_feature+0xf0/0x348
[ 188.694311] lr : verify_local_elf_hwcaps+0x84/0xe8
[ 188.694410] sp : ffff800011b1bf60
[ 188.694536] x29: ffff800011b1bf60 x28: 0000000000000000
[ 188.694707] x27: 0000000000000000 x26: 0000000000000000
[ 188.694801] x25: 0000000000000000 x24: ffff80001189a25c
[ 188.694905] x23: 0000000000000000 x22: 0000000000000000
[ 188.694996] x21: ffff8000114aa018 x20: ffff800011156a38
[ 188.695089] x19: ffff800010c944a0 x18: 0000000000000004
[ 188.695187] x17: 0000000000000000 x16: 0000000000000000
[ 188.695280] x15: 0000249dbde5431e x14: 0262cbe497efa1fa
[ 188.695371] x13: 0000000000000002 x12: 0000000000002592
[ 188.695472] x11: 0000000000000080 x10: 00400032b5503510
[ 188.695572] x9 : 0000000000000000 x8 : ffff800010c80204
[ 188.695659] x7 : 00000000410fd0f0 x6 : 0000000000000001
[ 188.695750] x5 : 00000000410fd0f0 x4 : 0000000000000000
[ 188.695836] x3 : 0000000000000000 x2 : ffff8000100939d8
[ 188.695919] x1 : 0000000000180420 x0 : 0000000000180480
[ 188.696253] Call trace:
[ 188.696410] has_cpuid_feature+0xf0/0x348
[ 188.696504] verify_local_elf_hwcaps+0x84/0xe8
[ 188.696591] check_local_cpu_capabilities+0x44/0x128
[ 188.696666] secondary_start_kernel+0xf4/0x188
[ 188.697150] Code: 52805001 72a00301 6b01001f 54000ec0 (d4210000)
[ 188.698639] ---[ end trace 3f12ca47652f7b72 ]---
[ 188.699160] Kernel panic - not syncing: Attempted to kill the idle task!
[ 188.699546] Kernel Offset: disabled
[ 188.699828] CPU features: 0x00004,20c02008
[ 188.700012] Memory Limit: none
[ 188.700538] ---[ end Kernel panic - not syncing: Attempted to kill the idle task! ]---
[root@arch ~]# echo Helo
Helo
[root@arch ~]# cat /proc/cpuinfo | grep proce
processor : 0
Make smp_send_stop() account also for the online status of the calling CPU
while evaluating how many CPUs are effectively online: this way, the right
number of STOPs is sent, so enforcing a proper freeze of the system at the
end of panic even under the above conditions.
Fixes: 08e875c16a16c ("arm64: SMP support")
Reported-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c54f90c2627cc316d365e3073614731e17dbc631 ]
LLVM's integrated assembler fails with the following error when
building KVM:
<inline asm>:12:6: error: expected absolute expression
.if kvm_update_va_mask == 0
^
<inline asm>:21:6: error: expected absolute expression
.if kvm_update_va_mask == 0
^
<inline asm>:24:2: error: unrecognized instruction mnemonic
NOT_AN_INSTRUCTION
^
LLVM ERROR: Error parsing inline asm
These errors come from ALTERNATIVE_CB and __ALTERNATIVE_CFG,
which test for the existence of the callback parameter in inline
assembly using the following expression:
" .if " __stringify(cb) " == 0\n"
This works with GNU as, but isn't supported by LLVM. This change
splits __ALTERNATIVE_CFG and ALTINSTR_ENTRY into separate macros
to fix the LLVM build.
Link: https://github.com/ClangBuiltLinux/linux/issues/472
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d026c96b25b7ce5df89526aad2df988d553edb4d ]
QUSB2 PHY on msm8996 doesn't work well when autosuspend by
dwc3 core using USB2PHYCFG register is enabled. One of the
issue seen is that PHY driver reports PLL lock failure and
fails phy_init() if dwc3 core has USB2 PHY suspend enabled.
Fix this by using quirks to disable USB2 PHY LPM/suspend and
dwc3 core already takes care of explicitly suspending PHY
during suspend if quirks are specified.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
Link: https://lore.kernel.org/r/20191209151501.26993-1-p.pisati@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit fca3d33d8ad61eb53eca3ee4cac476d1e31b9008 upstream.
When all CPUs in the system implement the SSBS extension, the SSBS field
in PSTATE is the definitive indication of the mitigation state. Further,
when the CPUs implement the SSBS manipulation instructions (advertised
to userspace via an HWCAP), EL0 can toggle the SSBS field directly and
so we cannot rely on any shadow state such as TIF_SSBD at all.
Avoid forcing the SSBS field in context-switch on such a system, and
simply rely on the PSTATE register instead.
Cc: <stable@vger.kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Srinivas Ramana <sramana@codeaurora.org>
Fixes: cbdf8a189a66 ("arm64: Force SSBS on context switch")
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52f73c383b2418f2d31b798e765ae7d596c35021 upstream
We detect the absence of FP/SIMD after an incapable CPU is brought up,
and by then we have kernel threads running already with TIF_FOREIGN_FPSTATE set
which could be set for early userspace applications (e.g, modprobe triggered
from initramfs) and init. This could cause the applications to loop forever in
do_nofity_resume() as we never clear the TIF flag, once we now know that
we don't support FP.
Fix this by making sure that we clear the TIF_FOREIGN_FPSTATE flag
for tasks which may have them set, as we would have done in the normal
case, but avoiding touching the hardware state (since we don't support any).
Cc: stable@vger.kernel.org # v4.14
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c9d66999f064947e6b577ceacc1eb2fbca6a8d3c upstream
When fp/simd is not supported on the system, fail the operations
of FP/SIMD regsets.
Cc: stable@vger.kernel.org # v4.14
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 7559950aef1ab8792c50797c6c5c7c5150a02460 upstream
We set the compat_elf_hwcap bits unconditionally on arm64 to
include the VFP and NEON support. However, the FP/SIMD unit
is optional on Arm v8 and thus could be missing. We already
handle this properly in the kernel, but still advertise to
the COMPAT applications that the VFP is available. Fix this
to make sure we only advertise when we really have them.
Cc: stable@vger.kernel.org # v4.14
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 449443c03d8cfdacf7313e17779a2594ebf87e6d upstream.
The NO_FPSIMD capability is defined with scope SYSTEM, which implies
that the "absence" of FP/SIMD on at least one CPU is detected only
after all the SMP CPUs are brought up. However, we use the status
of this capability for every context switch. So, let us change
the scope to LOCAL_CPU to allow the detection of this capability
as and when the first CPU without FP is brought up.
Also, the current type allows hotplugged CPU to be brought up without
FP/SIMD when all the current CPUs have FP/SIMD and we have the userspace
up. Fix both of these issues by changing the capability to
BOOT_RESTRICTED_LOCAL_CPU_FEATURE.
Fixes: 82e0191a1aa11abf ("arm64: Support systems without FP/ASIMD")
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b6ae256afd32f96bec0117175b329d0dd617655e upstream.
On AArch64 you can do a sign-extended load to either a 32-bit or 64-bit
register, and we should only sign extend the register up to the width of
the register as specified in the operation (by using the 32-bit Wn or
64-bit Xn register specifier).
As it turns out, the architecture provides this decoding information in
the SF ("Sixty-Four" -- how cute...) bit.
Let's take advantage of this with the usual 32-bit/64-bit header file
dance and do the right thing on AArch64 hosts.
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191212195055.5541-1-christoffer.dall@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d7bbd6c1b01cb5dd13c245d4586a83145c1d5f52 upstream.
Since v4.3-rc1 commit 0723c05fb75e44 ("arm64: enable more compressed
Image formats"), it is possible to build Image.{bz2,lz4,lzma,lzo}
AArch64 images. However, the commit missed adding support for removing
those images on 'make ARCH=arm64 (dist)clean'.
Fix this by adding them to the target list.
Make sure to match the order of the recipes in the makefile.
Cc: stable@vger.kernel.org # v4.3+
Fixes: 0723c05fb75e44 ("arm64: enable more compressed Image formats")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 39a1a8941b27c37f79508426e27a2ec29829d66c ]
Older versions of the Juno *SoC* TRM [1] recommended that the UART clock
source should be 7.2738 MHz, whereas the *system* TRM [2] stated a more
correct value of 7.3728 MHz. Somehow the wrong value managed to end up in
our DT.
Doing a prime factorisation, a modulo divide by 115200 and trying
to buy a 7.2738 MHz crystal at your favourite electronics dealer suggest
that the old value was actually a typo. The actual UART clock is driven
by a PLL, configured via a parameter in some board.txt file in the
firmware, which reads 7.37 MHz (sic!).
Fix this to correct the baud rate divisor calculation on the Juno board.
[1] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0515b.b/DDI0515B_b_juno_arm_development_platform_soc_trm.pdf
[2] http://infocenter.arm.com/help/topic/com.arm.doc.100113_0000_07_en/arm_versatile_express_juno_development_platform_(v2m_juno)_technical_reference_manual_100113_0000_07_en.pdf
Fixes: 71f867ec130e ("arm64: Add Juno board device tree.")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9f72e321d5506fe3e162a6308a4a295d7f10bb5d ]
The eMMC on this board is add-on module which is not mandatory. Removing
'non-removable' property should prevent some errors when booting a board
w/o an eMMC module present.
Fixes: 72fb2c852188 ("ARM64: dts: meson-gxl-s905x-libretech-cc: fixup board definition")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 562bf19611c000cb7219431c3cc78aa60c2b371e ]
The pinctrl binding mandates that we have the three clocks fed into the PIO
described.
Even though the old case is still supported for backward compatibility, we
should update our DTs to fix this.
Fixes: 6bc37fac30cf ("arm64: dts: add Allwinner A64 SoC .dtsi")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit af61bef513ba179559e56908b8c465e587bc3890 ]
In the same way as for msm8974-hammerhead, l11 load, used for SDCARD
VMMC, needs to be increased in order to prevent any voltage drop issues
(due to limited current) happening with some SDCARDS or during specific
operations (e.g. write).
Tested on Dragonboard-410c and DART-SD410 boards.
Fixes: 4c7d53d16d77 (arm64: dts: apq8016-sbc: add regulators support)
Reported-by: Manabu Igusa <migusa@arrowjapan.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 54fb3fe0f211d4729a2551cf9497bd612189af9d upstream.
This reverts commit 193d00a2b35ee3353813b4006a18131122087205.
Commit 951d48855d86 ("of: Make of_dma_get_range() work on bus nodes")
reworked the logic such that of_dma_get_range() works correctly
starting from a bus node containing "dma-ranges".
Since on Juno we don't have a SoC level bus node and "dma-ranges" is
present only in the root node, we get the following error:
OF: translation of DMA address(0) to CPU address failed node(/sram@2e000000)
OF: translation of DMA address(0) to CPU address failed node(/uart@7ff80000)
...
OF: translation of DMA address(0) to CPU address failed node(/mhu@2b1f0000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
So let's fix it by dropping the "dma-ranges" property for now. This
should be fine since it doesn't represent any kind of device-visible
restriction; it was only there for completeness, and we've since given
in to the assumption that missing "dma-ranges" implies a 1:1 mapping
anyway.
We can add it later with a proper SoC bus node and moving all the
devices that belong there along with the "dma-ranges" if required.
Fixes: 193d00a2b35e ("arm64: dts: juno: add dma-ranges property")
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
