summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)AuthorFilesLines
2024-03-27ARM: dts: imx6dl-yapp4: Move the internal switch PHYs under the switch nodeMichal Vokáč1-8/+15
[ Upstream commit 79978bff2e4b8e05ebdf5fc3ee6b794002393484 ] We identified that the PHYs actually do not work since commit 7da7b84fee58 ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as a coincidence of several circumstances. The reset signal is kept asserted by a pull-down resistor on the board unless it is deasserted by GPIO from the SoC. This is to keep the switch dead until it is configured properly by the kernel and user space. Prior to the referenced commit the switch was reset by the FEC driver and the reset GPIO was actively deasserted. The mdio-bus was scanned and the attached switch and its PHYs were found and configured. With the referenced commit the switch is reset by the qca8k driver. Because of another bug in the qca8k driver, functionality of the reset pin depends on its pre-kernel configuration. See commit c44fc98f0a8f ("net: dsa: qca8k: fix illegal usage of GPIO") The problem did not appear until we removed support for the switch and configuration of its reset pin from the bootloader. To fix that, properly describe the internal mdio-bus configuration of the qca8334 switch. The PHYs are internal to the switch and sit on its internal mdio-bus. Fixes: 7da7b84fee58 ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-27ARM: dts: imx6dl-yapp4: Fix typo in the QCA switch register addressMichal Vokáč1-1/+1
[ Upstream commit 023bd910d3ab735459f84b22bb99fb9e00bd9d76 ] This change does not have any functional effect. The switch works just fine without this patch as it has full access to all the addresses on the bus. This is simply a clean-up to set the node name address and reg address to the same value. Fixes: 15b43e497ffd ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch") Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-27ARM: dts: arm: realview: Fix development chip ROM compatible valueGeert Uytterhoeven1-1/+1
[ Upstream commit 3baa4c5143d65ebab2de0d99a395e5f4f1f46608 ] When the development chip ROM was added, the "direct-mapped" compatible value was already obsolete. In addition, the device node lacked the accompanying "probe-type" property, causing the old physmap_of_core driver to fall back to trying all available probe types. Unfortunately this fallback was lost when the DT and pdata cases were merged. Fix this by using the modern "mtd-rom" compatible value instead. Fixes: 5c3f5edbe0a1dff3 ("ARM: realview: add flash devices to the PB1176 DTS") Fixes: 642b1e8dbed7bbbf ("mtd: maps: Merge physmap_of.c into physmap-core.c") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-27ARM: dts: qcom: msm8974: correct qfprom node sizeCraig Tatlor1-1/+1
[ Upstream commit 724c4bf0e4bf81dba77736afb93964c986c3c123 ] The qfprom actually is bigger than 0x1000, so adjust the reg. Note that the non-ECC-corrected qfprom can be found at 0xfc4b8000 (-0x4000). The current reg points to the ECC-corrected qfprom block which should have equivalent values at all offsets compared to the non-corrected version. [luca@z3ntu.xyz: extract to standalone patch and adjust for review comments] Fixes: c59ffb519357 ("arm: dts: msm8974: Add thermal zones, tsens and qfprom nodes") Signed-off-by: Craig Tatlor <ctatlor97@gmail.com> Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20240210-msm8974-qfprom-v3-1-26c424160334@z3ntu.xyz Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-27ARM: dts: renesas: r8a73a4: Fix external clocks and clock rateGeert Uytterhoeven2-3/+18
[ Upstream commit 090c4094574705b0afc7d37825cdc5d06f0e7e02 ] External clocks should be defined as zero-Hz clocks in the SoC .dtsi, and overridden in the board .dts when present. Correct the clock rate of extal1 from 25 to 26 MHz, to match the crystal oscillator present on the APE6-EVM board. Fixes: a76809a329d6ebae ("ARM: shmobile: r8a73a4: Common clock framework DT description") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Link: https://lore.kernel.org/r/1692bc8cd465d62168cbf110522ad62a7af3f606.1705315614.git.geert+renesas@glider.be Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-27ARM: dts: renesas: rcar-gen2: Add missing #interrupt-cells to DA9063 nodesGeert Uytterhoeven8-0/+8
[ Upstream commit 8c987693dc2d292d777f1be63cb35233049ae25e ] make dtbs_check W=2: arch/arm/boot/dts/renesas/r8a7790-lager.dts:444.11-458.5: Warning (interrupt_provider): /i2c-mux4/pmic@58: Missing '#interrupt-cells' in interrupt provider ... Fix this by adding the missing #interrupt-cells properties. Reported-by: Rob Herring <robh@kernel.org> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/a351e503ea97fb1af68395843f513925ff1bdf26.1707922460.git.geert+renesas@glider.be Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-27arm: dts: Fix dtc interrupt_map warningsRob Herring3-4/+8
[ Upstream commit f02b0f0dc26fbb77fe47b6e47cc5c211f0432c37 ] The dtc interrupt_map warning is off because its dependency, interrupt_provider, is off by default. Fix all the warnings so it can be enabled. Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-4-f2dee1292525@kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-27arm: dts: Fix dtc interrupt_provider warningsRob Herring24-58/+18
[ Upstream commit 96fd598e9c34cfa68402a4da3020c9236cfacf35 ] The dtc interrupt_provider warning is off by default. Fix all the warnings so it can be enabled. Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au> Reviewed-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom Acked-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-2-f2dee1292525@kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-27ARM: dts: rockchip: Drop interrupts property from pwm-rockchip nodesUwe Kleine-König1-8/+0
[ Upstream commit f98643d8daf3443e3b414a82d0cb3d745f8c8bbc ] The binding doesn't define interrupts and adding such a definition was refused because it's unclear how they should ever be used and the relevant registers are outside the PWM range. So drop them fixing several dtbs_check warnings like: arch/arm/boot/dts/rockchip/rv1108-elgin-r1.dtb: pwm@10280030: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/pwm/pwm-rockchip.yaml# Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20240129113205.2453029-2-u.kleine-koenig@pengutronix.de Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-01ARM: ep93xx: Add terminator to gpiod_lookup_tableNikita Shubin1-0/+1
commit fdf87a0dc26d0550c60edc911cda42f9afec3557 upstream. Without the terminator, if a con_id is passed to gpio_find() that does not exist in the lookup table the function will not stop looping correctly, and eventually cause an oops. Cc: stable@vger.kernel.org Fixes: b2e63555592f ("i2c: gpio: Convert to use descriptors") Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com> Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Link: https://lore.kernel.org/r/20240205102337.439002-1-alexander.sverdlin@gmail.com Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-03-01ARM: dts: Fix TPM schema violationsLukas Wunner7-10/+10
[ Upstream commit 8412c47d68436b9f9a260039a4a773daa6824925 ] Since commit 26c9d152ebf3 ("dt-bindings: tpm: Consolidate TCG TIS bindings"), several issues are reported by "make dtbs_check" for ARM devicetrees: The nodename needs to be "tpm@0" rather than "tpmdev@0" and the compatible property needs to contain the chip's name in addition to the generic "tcg,tpm_tis-spi" or "tcg,tpm-tis-i2c": tpmdev@0: $nodename:0: 'tpmdev@0' does not match '^tpm(@[0-9a-f]+)?$' from schema $id: http://devicetree.org/schemas/tpm/tcg,tpm_tis-spi.yaml# tpm@2e: compatible: 'oneOf' conditional failed, one must be fixed: ['tcg,tpm-tis-i2c'] is too short from schema $id: http://devicetree.org/schemas/tpm/tcg,tpm-tis-i2c.yaml# Fix these schema violations. Aspeed Facebook BMCs use an Infineon SLB9670: https://lore.kernel.org/all/ZZSmMJ%2F%2Fl972Qbxu@fedora/ https://lore.kernel.org/all/ZZT4%2Fw2eVzMhtsPx@fedora/ https://lore.kernel.org/all/ZZTS0p1hdAchIbKp@heinlein.vulture-banana.ts.net/ Aspeed Tacoma uses a Nuvoton NPCT75X per commit 39d8a73c53a2 ("ARM: dts: aspeed: tacoma: Add TPM"). phyGATE-Tauri uses an Infineon SLB9670: https://lore.kernel.org/all/ab45c82485fa272f74adf560cbb58ee60cc42689.camel@phytec.de/ A single schema violation remains in am335x-moxa-uc-2100-common.dtsi because it is unknown which chip is used on the board. The devicetree's author has been asked for clarification but has not responded so far: https://lore.kernel.org/all/20231220090910.GA32182@wunner.de/ Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Patrick Williams <patrick@stwcx.xyz> Reviewed-by: Tao Ren <rentao.bupt@gmail.com> Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-23work around gcc bugs with 'asm goto' with outputsLinus Torvalds1-2/+2
commit 4356e9f841f7fbb945521cef3577ba394c65f3fc upstream. We've had issues with gcc and 'asm goto' before, and we created a 'asm_volatile_goto()' macro for that in the past: see commits 3f0116c3238a ("compiler/gcc4: Add quirk for 'asm goto' miscompilation bug") and a9f180345f53 ("compiler/gcc4: Make quirk for asm_volatile_goto() unconditional"). Then, much later, we ended up removing the workaround in commit 43c249ea0b1e ("compiler-gcc.h: remove ancient workaround for gcc PR 58670") because we no longer supported building the kernel with the affected gcc versions, but we left the macro uses around. Now, Sean Christopherson reports a new version of a very similar problem, which is fixed by re-applying that ancient workaround. But the problem in question is limited to only the 'asm goto with outputs' cases, so instead of re-introducing the old workaround as-is, let's rename and limit the workaround to just that much less common case. It looks like there are at least two separate issues that all hit in this area: (a) some versions of gcc don't mark the asm goto as 'volatile' when it has outputs: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=98619 https://gcc.gnu.org/bugzilla/show_bug.cgi?id=110420 which is easy to work around by just adding the 'volatile' by hand. (b) Internal compiler errors: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=110422 which are worked around by adding the extra empty 'asm' as a barrier, as in the original workaround. but the problem Sean sees may be a third thing since it involves bad code generation (not an ICE) even with the manually added 'volatile'. but the same old workaround works for this case, even if this feels a bit like voodoo programming and may only be hiding the issue. Reported-and-tested-by: Sean Christopherson <seanjc@google.com> Link: https://lore.kernel.org/all/20240208220604.140859-1-seanjc@google.com/ Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Uros Bizjak <ubizjak@gmail.com> Cc: Jakub Jelinek <jakub@redhat.com> Cc: Andrew Pinski <quic_apinski@quicinc.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-02-16mm: Introduce flush_cache_vmap_early()Alexandre Ghiti1-0/+2
[ Upstream commit 7a92fc8b4d20680e4c20289a670d8fca2d1f2c1b ] The pcpu setup when using the page allocator sets up a new vmalloc mapping very early in the boot process, so early that it cannot use the flush_cache_vmap() function which may depend on structures not yet initialized (for example in riscv, we currently send an IPI to flush other cpus TLB). But on some architectures, we must call flush_cache_vmap(): for example, in riscv, some uarchs can cache invalid TLB entries so we need to flush the new established mapping to avoid taking an exception. So fix this by introducing a new function flush_cache_vmap_early() which is called right after setting the new page table entry and before accessing this new mapping. This new function implements a local flush tlb on riscv and is no-op for other architectures (same as today). Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Dennis Zhou <dennis@kernel.org> Stable-dep-of: d9807d60c145 ("riscv: mm: execute local TLB flush after populating vmemmap") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: imx23/28: Fix the DMA controller node nameFabio Estevam2-2/+2
[ Upstream commit 858d83ca4b50bbc8693d95cc94310e6d791fb2e6 ] Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'. Change it to fix the following dt-schema warning. imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$' from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml# Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: imx23-sansa: Use preferred i2c-gpios propertiesFabio Estevam1-8/+4
[ Upstream commit e3aa1a82fb20ee97597022f6528823a8ab82bde6 ] The 'gpios' property to describe the SDA and SCL GPIOs is considered deprecated according to i2c-gpio.yaml. Switch to the preferred 'sda-gpios' and 'scl-gpios' properties. This fixes the following schema warnings: imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml# imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml# Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: imx27-apf27dev: Fix LED nameFabio Estevam1-1/+1
[ Upstream commit dc35e253d032b959d92e12f081db5b00db26ae64 ] Per leds-gpio.yaml, the led names should start with 'led'. Change it to fix the following dt-schema warning: imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml# Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: imx25/27: Pass timing0Fabio Estevam8-8/+8
[ Upstream commit 11ab7ad6f795ae23c398a4a5c56505d3dab27c4c ] Per display-timings.yaml, the 'timing' pattern should be used to describe the display timings. Change it accordingly to fix the following dt-schema warning: imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml# Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: imx25: Fix the iim compatible stringFabio Estevam1-1/+1
[ Upstream commit f0b929f58719fc57a4926ab4fc972f185453d6a5 ] Per imx-iim.yaml, the compatible string should only contain a single entry. Use it as "fsl,imx25-iim" to fix the following dt-schema warning: imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml# Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: imx1: Fix sram nodeFabio Estevam1-1/+4
[ Upstream commit c248e535973088ba7071ff6f26ab7951143450af ] Per sram.yaml, address-cells, size-cells and ranges are mandatory. The node name should be sram. Change the node name and pass the required properties to fix the following dt-schema warnings: imx1-apf9328.dtb: esram@300000: $nodename:0: 'esram@300000' does not match '^sram(@.*)?' from schema $id: http://devicetree.org/schemas/sram/sram.yaml# imx1-apf9328.dtb: esram@300000: '#address-cells' is a required property from schema $id: http://devicetree.org/schemas/sram/sram.yaml# imx1-apf9328.dtb: esram@300000: '#size-cells' is a required property from schema $id: http://devicetree.org/schemas/sram/sram.yaml# imx1-apf9328.dtb: esram@300000: 'ranges' is a required property from schema $id: http://devicetree.org/schemas/sram/sram.yaml# Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: imx27: Fix sram nodeFabio Estevam1-0/+3
[ Upstream commit 2fb7b2a2f06bb3f8321cf26c33e4e820c5b238b6 ] Per sram.yaml, address-cells, size-cells and ranges are mandatory. Pass them to fix the following dt-schema warnings: Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: imx: Use flash@0,0 patternFabio Estevam4-4/+4
[ Upstream commit 1e1d7cc478fb16816de09740e3c323c0c188d58f ] Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern. Change it to 'flash@0,0' to fix the following dt-schema warning: imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$' from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml# Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: imx25/27-eukrea: Fix RTC node nameFabio Estevam2-2/+2
[ Upstream commit 68c711b882c262e36895547cddea2c2d56ce611d ] Node names should be generic. Use 'rtc' as node name to fix the following dt-schema warning: imx25-eukrea-mbimxsd25-baseboard.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$' from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml# Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: rockchip: fix rk3036 hdmi ports nodeJohan Jonker1-3/+11
[ Upstream commit 27ded76ef0fcfcf939914532aae575cf23c221b4 ] Fix hdmi ports node so that it matches the rockchip,inno-hdmi.yaml binding. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Link: https://lore.kernel.org/r/9a2afac1-ed5c-382d-02b0-b2f5f1af3abb@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: imx7s: Fix nand-controller #size-cellsAlexander Stein1-1/+1
[ Upstream commit 4aadb841ed49bada1415c48c44d21f5b69e01299 ] nand-controller.yaml bindings says #size-cells shall be set to 0. Fixes the dtbs_check warning: arch/arm/boot/dts/nxp/imx/imx7s-mba7.dtb: nand-controller@33002000: #size-cells:0:0: 0 was expected from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml# Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: imx7s: Fix lcdif compatibleAlexander Stein1-1/+1
[ Upstream commit 5f55da4cc37051cda600ea870ce8cf29f1297715 ] imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay by using LCDC_AS_CTRL register. This registers used by overlay plane: * LCDC_AS_CTRL * LCDC_AS_BUF * LCDC_AS_NEXT_BUF are listed in i.MX7D RM as well. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: imx7d: Fix coresight funnel portsAlexander Stein2-4/+5
[ Upstream commit 0d4ac04fa7c3f6dc263dba6f575a2ec7a2d4eca8 ] imx7d uses two ports for 'in-ports', so the syntax port@<num> has to be used. imx7d has both port and port@1 nodes present, raising these error: funnel@30041000: in-ports: More than one condition true in oneOf schema funnel@30041000: Unevaluated properties are not allowed ('in-ports' was unexpected) Fix this by also using port@0 for imx7s as well. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: samsung: s5pv210: fix camera unit addresses/rangesKrzysztof Kozlowski1-9/+9
[ Upstream commit 07e6a553c2f1d385edfc9185081dee442a9dd38d ] The camera node has both unit address and children within the same bus mapping, thus needs proper ranges property to fix dtc W=1 warnings: Warning (unit_address_vs_reg): /soc/camera@fa600000: node has a unit name, but no reg or ranges property Warning (simple_bus_reg): /soc/camera@fa600000: missing or empty reg/ranges property Subtract 0xfa600000 from all its children nodes. No functional impact expected. Link: https://lore.kernel.org/r/20230722121719.150094-3-krzysztof.kozlowski@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: samsung: exynos4: fix camera unit addresses/rangesKrzysztof Kozlowski2-21/+22
[ Upstream commit ba2a45a48503665f7e8eeec51f8b40456566b0cd ] The camera node has both unit address and children within the same bus mapping, thus needs proper ranges property to fix dtc W=1 warnings: Warning (unit_address_vs_reg): /soc/camera@11800000: node has a unit name, but no reg or ranges property Warning (simple_bus_reg): /soc/camera@11800000: missing or empty reg/ranges property Subtract 0x11800000 from all its children nodes. No functional impact expected. Link: https://lore.kernel.org/r/20230722121719.150094-2-krzysztof.kozlowski@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: qcom: msm8660: fix PMIC node labelsDmitry Baryshkov2-10/+10
[ Upstream commit c6d86aa8a12194d1c9c2f9108910a46c8a3ddc90 ] Change PM8058 node labels to start with pm8058_ prefix, following other Qualcomm PMIC device nodes. Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20230928110309.1212221-11-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: qcom: mdm9615: fix PMIC node labelsDmitry Baryshkov2-8/+8
[ Upstream commit 0e4688cd4ee6efbeae2b31f75e16961fd7f72735 ] Change PM8018 node labels to start with pm8018_ prefix, following other Qualcomm PMIC device nodes. Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20230928110309.1212221-10-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05ARM: dts: qcom: strip prefix from PMIC filesDmitry Baryshkov23-23/+23
[ Upstream commit 455a4c46e023ab84263eae0fc7acca9a5ee8b7ac ] As the vendor DTS files were moved to per-vendor subdirs, there no need to use common prefixes. Drop the `qcom-' prefix from PMIC dtsi file. This makes 32-bit qcom/ dts files closer to arm64 ones. Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20230928110309.1212221-8-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05arch: consolidate arch_irq_work_raise prototypesArnd Bergmann1-2/+0
[ Upstream commit 64bac5ea17d527872121adddfee869c7a0618f8f ] The prototype was hidden in an #ifdef on x86, which causes a warning: kernel/irq_work.c:72:13: error: no previous prototype for 'arch_irq_work_raise' [-Werror=missing-prototypes] Some architectures have a working prototype, while others don't. Fix this by providing it in only one place that is always visible. Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Palmer Dabbelt <palmer@rivosinc.com> Acked-by: Guo Ren <guoren@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-01ARM: dts: exynos4212-tab3: add samsung,invert-vclk flag to fimdArtur Weber1-0/+1
[ Upstream commit eab4f56d3e75dad697acf8dc2c8be3c341d6c63e ] After more investigation, I've found that it's not the panel driver config that needs to be modified to invert the data polarity, but the FIMD config. Add the missing invert-vclk option that is required to get the display to work correctly. Fixes: ee37a457af1d ("ARM: dts: exynos: Add Samsung Galaxy Tab 3 8.0 boards") Signed-off-by: Artur Weber <aweber.kernel@gmail.com> Link: https://lore.kernel.org/r/20240105-tab3-display-fixes-v2-1-904d1207bf6f@gmail.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-01ARM: dts: qcom: sdx55: fix USB SS wakeupJohan Hovold1-1/+1
commit 710dd03464e4ab5b3d329768388b165d61958577 upstream. The USB SS PHY interrupt needs to be provided by the PDC interrupt controller in order to be able to wake the system up from low-power states. Fixes: fea4b41022f3 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support") Cc: stable@vger.kernel.org # 5.12 Cc: Manivannan Sadhasivam <mani@kernel.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20231213173131.29436-4-johan+linaro@kernel.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-02-01ARM: dts: qcom: sdx55: fix USB DP/DM HS PHY interruptsJohan Hovold1-4/+4
commit de95f139394a5ed82270f005bc441d2e7c1e51b7 upstream. The USB DP/DM HS PHY interrupts need to be provided by the PDC interrupt controller in order to be able to wake the system up from low-power states and to be able to detect disconnect events, which requires triggering on falling edges. A recent commit updated the trigger type but failed to change the interrupt provider as required. This leads to the current Linux driver failing to probe instead of printing an error during suspend and USB wakeup not working as intended. Fixes: d0ec3c4c11c3 ("ARM: dts: qcom: sdx55: fix USB wakeup interrupt types") Fixes: fea4b41022f3 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support") Cc: stable@vger.kernel.org # 5.12 Cc: Manivannan Sadhasivam <mani@kernel.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20231213173131.29436-3-johan+linaro@kernel.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-02-01ARM: dts: qcom: sdx55: fix pdc '#interrupt-cells'Johan Hovold1-1/+1
commit cc25bd06c16aa582596a058d375b2e3133f79b93 upstream. The Qualcomm PDC interrupt controller binding expects two cells in interrupt specifiers. Fixes: 9d038b2e62de ("ARM: dts: qcom: Add SDX55 platform and MTP board support") Cc: stable@vger.kernel.org # 5.12 Cc: Manivannan Sadhasivam <mani@kernel.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20231213173131.29436-2-johan+linaro@kernel.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-02-01ARM: dts: samsung: exynos4210-i9100: Unconditionally enable LDO12Paul Cercueil1-0/+8
commit 84228d5e29dbc7a6be51e221000e1d122125826c upstream. The kernel hangs for a good 12 seconds without any info being printed to dmesg, very early in the boot process, if this regulator is not enabled. Force-enable it to work around this issue, until we know more about the underlying problem. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Fixes: 8620cc2f99b7 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2") Cc: stable@vger.kernel.org # v5.8+ Link: https://lore.kernel.org/r/20231206221556.15348-2-paul@crapouillou.net Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-02-01ARM: dts: qcom: sdx55: fix USB wakeup interrupt typesJohan Hovold1-2/+2
commit d0ec3c4c11c3b30e1f2d344973b2a7bf0f986734 upstream. The DP/DM wakeup interrupts are edge triggered and which edge to trigger on depends on use-case and whether a Low speed or Full/High speed device is connected. Fixes: fea4b41022f3 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support") Cc: stable@vger.kernel.org # 5.12 Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20231120164331.8116-2-johan+linaro@kernel.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-02-01ARM: dts: imx6q-apalis: add can power-up delay on ixora boardAndrejs Cainikovs1-0/+2
commit b76bbf835d8945080b22b52fc1e6f41cde06865d upstream. Newer variants of Ixora boards require a power-up delay when powering up the CAN transceiver of up to 1ms. Cc: stable@vger.kernel.org Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-01-26ARM: 9330/1: davinci: also select PINCTRLRandy Dunlap1-0/+1
[ Upstream commit f54e8634d1366926c807e2af6125b33cff555fa7 ] kconfig warns when PINCTRL_SINGLE is selected but PINCTRL is not set, so also set PINCTRL for ARCH_DAVINCI. This prevents a kconfig/build warning: WARNING: unmet direct dependencies detected for PINCTRL_SINGLE Depends on [n]: PINCTRL [=n] && OF [=y] && HAS_IOMEM [=y] Selected by [y]: - ARCH_DAVINCI [=y] && ARCH_MULTI_V5 [=y] Closes: lore.kernel.org/r/202311070548.0f6XfBrh-lkp@intel.com Fixes: f962396ce292 ("ARM: davinci: support multiplatform build for ARM v5") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Bartosz Golaszewski <brgl@bgdev.pl> Cc: Arnd Bergmann <arnd@arndb.de> Cc: linux-arm-kernel@lists.infradead.org Cc: patches@armlinux.org.uk Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-26ARM: davinci: always select CONFIG_CPU_ARM926TArnd Bergmann1-0/+1
[ Upstream commit 40974ee421b4d1fc74ac733d86899ce1b83d8f65 ] The select was lost by accident during the multiplatform conversion. Any davinci-only arm-linux-gnueabi-ld: arch/arm/mach-davinci/sleep.o: in function `CACHE_FLUSH': (.text+0x168): undefined reference to `arm926_flush_kern_cache_all' Fixes: f962396ce292 ("ARM: davinci: support multiplatform build for ARM v5") Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Link: https://lore.kernel.org/r/20240108110055.1531153-1-arnd@kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-26ARM: dts: stm32: don't mix SCMI and non-SCMI board compatiblesAhmad Fatoum4-5/+4
[ Upstream commit bfc3c6743de0ecb169026c36cbdbc0d12d22a528 ] The binding erroneously decreed that the SCMI variants of the ST evaluation kits are compatible with the non-SCMI variants. This is not correct, as a kernel or bootloader compatible with the non-SCMI variant is not necessarily able to function, when direct access to resources is replaced by having to talk SCMI to the secure monitor. The binding has been adjusted to reflect thus, so synchronize the device trees now. Fixes: 5b7e58313a77 ("ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)") Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-26ARM: dts: qcom: sdx65: correct SPMI node nameKrzysztof Kozlowski1-1/+1
[ Upstream commit a900ad783f507cb396e402827052e70c0c565ae9 ] Node names should not have vendor prefixes: qcom-sdx65-mtp.dtb: qcom,spmi@c440000: $nodename:0: 'qcom,spmi@c440000' does not match '^spmi@.* Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20230924183103.49487-3-krzysztof.kozlowski@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-26ARM: dts: qcom: sdx65: correct PCIe EP phy-namesKrzysztof Kozlowski1-1/+1
[ Upstream commit 94da379dba88c4cdd562bad21c9ba5656e5ed5df ] Qualcomm PCIe endpoint bindings expect phy-names to be "pciephy": arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dtb: pcie-ep@1c00000: phy-names:0: 'pciephy' was expected Fixes: 9c0bb38414a4 ("ARM: dts: qcom: sdx65: Add support for PCIe EP") Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20230924183103.49487-1-krzysztof.kozlowski@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-26ARM: dts: qcom: apq8064: correct XOADC register addressDmitry Baryshkov1-1/+1
[ Upstream commit 554557542e709e190eff8a598f0cde02647d533a ] The XOADC is present at the address 0x197 rather than just 197. It doesn't change a lot (since the driver hardcodes all register addresses), but the DT should present correct address anyway. Fixes: c4b70883ee33 ("ARM: dts: add XOADC and IIO HWMON to APQ8064") Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20230928110309.1212221-3-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-26ARM: dts: qcom: msm8226: provide dsi phy clocks to mmccLuca Weiss1-2/+2
[ Upstream commit 836d083524888069cd358776a4e6c4ceec04962e ] Some mmcc clocks have dsi0pll & dsi0pllbyte as clock parents so we should provide them in the dt, which I missed in the commit adding the mdss nodes. Fixes: d5fb01ad5eb4 ("ARM: dts: qcom: msm8226: Add mdss nodes") Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20230712-msm8226-dsi-clock-fixup-v1-1-71010b0b89ca@z3ntu.xyz Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-20ARM: sun9i: smp: fix return code check of of_property_match_stringStefan Wahren1-2/+2
[ Upstream commit 643fe70e7bcdcc9e2d96952f7fc2bab56385cce5 ] of_property_match_string returns an int; either an index from 0 or greater if successful or negative on failure. Even it's very unlikely that the DT CPU node contains multiple enable-methods these checks should be fixed. This patch was inspired by the work of Nick Desaulniers. Link: https://lore.kernel.org/lkml/20230516-sunxi-v1-1-ac4b9651a8c1@google.com/T/ Cc: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Link: https://lore.kernel.org/r/20231228193903.9078-2-wahrenst@gmx.net Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-10ARM: sun9i: smp: Fix array-index-out-of-bounds read in sunxi_mc_smp_initStefan Wahren1-2/+2
[ Upstream commit 72ad3b772b6d393701df58ba1359b0bb346a19ed ] Running a multi-arch kernel (multi_v7_defconfig) on a Raspberry Pi 3B+ with enabled CONFIG_UBSAN triggers the following warning: UBSAN: array-index-out-of-bounds in arch/arm/mach-sunxi/mc_smp.c:810:29 index 2 is out of range for type 'sunxi_mc_smp_data [2]' CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.7.0-rc6-00248-g5254c0cbc92d Hardware name: BCM2835 unwind_backtrace from show_stack+0x10/0x14 show_stack from dump_stack_lvl+0x40/0x4c dump_stack_lvl from ubsan_epilogue+0x8/0x34 ubsan_epilogue from __ubsan_handle_out_of_bounds+0x78/0x80 __ubsan_handle_out_of_bounds from sunxi_mc_smp_init+0xe4/0x4cc sunxi_mc_smp_init from do_one_initcall+0xa0/0x2fc do_one_initcall from kernel_init_freeable+0xf4/0x2f4 kernel_init_freeable from kernel_init+0x18/0x158 kernel_init from ret_from_fork+0x14/0x28 Since the enabled method couldn't match with any entry from sunxi_mc_smp_data, the value of the index shouldn't be used right after the loop. So move it after the check of ret in order to have a valid index. Fixes: 1631090e34f5 ("ARM: sun9i: smp: Add is_a83t field") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Link: https://lore.kernel.org/r/20231228193903.9078-1-wahrenst@gmx.net Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-01ARM: dts: Fix occasional boot hang for am3 usbTony Lindgren1-0/+1
commit 9b6a51aab5f5f9f71d2fa16e8b4d530e1643dfcb upstream. With subtle timings changes, we can now sometimes get an external abort on non-linefetch error booting am3 devices at sysc_reset(). This is because of a missing reset delay needed for the usb target module. Looks like we never enabled the delay earlier for am3, although a similar issue was seen earlier with a similar usb setup for dm814x as described in commit ebf244148092 ("ARM: OMAP2+: Use srst_udelay for USB on dm814x"). Cc: stable@vger.kernel.org Fixes: 0782e8572ce4 ("ARM: dts: Probe am335x musb with ti-sysc") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-01-01ARM: OMAP2+: Fix null pointer dereference and memory leak in ↵Kunwu Chan1-0/+5
omap_soc_device_init [ Upstream commit c72b9c33ef9695ad7ce7a6eb39a9df8a01b70796 ] kasprintf() returns a pointer to dynamically allocated memory which can be NULL upon failure. When 'soc_dev_attr->family' is NULL,it'll trigger the null pointer dereference issue, such as in 'soc_info_show'. And when 'soc_device_register' fails, it's necessary to release 'soc_dev_attr->family' to avoid memory leaks. Fixes: 6770b2114325 ("ARM: OMAP2+: Export SoC information to userspace") Signed-off-by: Kunwu Chan <chentao@kylinos.cn> Message-ID: <20231123145237.609442-1-chentao@kylinos.cn> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-24 21:26:13 +0300