summaryrefslogtreecommitdiff
path: root/arch/avr32/include/asm/atmel-mci.h
AgeCommit message (Collapse)AuthorFilesLines
2009-01-05atmel-mci: move atmel-mci.h file to include/linuxNicolas Ferre1-39/+0
Needed to use the atmel-mci driver in an architecture independant maner. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-05atmel-mci: Add experimental DMA supportHaavard Skinnemoen1-0/+4
This adds support for DMA transfers through the generic DMA engine framework with the DMA slave extensions. The driver has been tested using mmc-block and ext3fs on several SD, SDHC and MMC+ cards. Reads and writes work fine, with read transfer rates up to 7.5 MiB/s on fast cards with debugging disabled. Unfortunately, the driver has been known to lock up from time to time with DMA enabled, so DMA support is currently optional and marked EXPERIMENTAL. However, I didn't see any problems while testing 13 different cards (MMC, SD and SDHC of different brands and sizes), so I suspect the "Initialize BLKR before sending data transfer command" fix that was posted earlier fixed this as well. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-05atmel-mci: support multiple mmc slotsHaavard Skinnemoen1-1/+7
The Atmel MCI controller can drive multiple cards through separate sets of pins, but only one at a time. This patch adds support for multiplexing access to the controller so that multiple card slots can be used as if they were hooked up to separate mmc controllers. The atmel-mci driver registers each slot as a separate mmc_host. Both access the same common controller state, but they also have some state on their own for card detection/write protect handling, and separate shadows of the MR and SDCR registers. When one of the slots receives a request from the mmc core, the common controller state is checked. If it's idle, the request is submitted immediately. If not, the request is added to a queue. When a request is done, the queue is checked and if there is a queued request, it is submitted before the completion callback is called. This patch also includes a few cleanups and fixes, including a locking overhaul. I had to change the locking extensively in any case, so I might as well try to get it right. The driver no longer takes any irq-safe locks, which may or may not improve the overall system performance. This patch also adds a bit of documentation of the internal data structures. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-05atmel-mci: Platform code for supporting multiple mmc slotsHaavard Skinnemoen1-1/+21
Add the necessary platform infrastructure to support multiple mmc/sdcard slots all at once through a single controller. Currently, the driver will use the first valid slot it finds and stick with that, but later patches will add support for switching between several slots on the fly. Extend the platform data structure with per-slot information: MMC/SDcard bus width and card detect/write protect pins. This will affect the pin muxing as well as the capabilities announced to the mmc core. Note that board code is now required to supply a mci_platform_data struct to at32_add_device_mci(). Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-05avr32: Move include/asm-avr32 to arch/avr32/include/asmHaavard Skinnemoen1-0/+9
Leaving include/asm/arch alone for now. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>