summaryrefslogtreecommitdiff
path: root/arch/riscv
AgeCommit message (Collapse)AuthorFilesLines
2023-10-26Merge tag 'soc-fixes-6.7-3' of ↵Linus Torvalds4-3/+4
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "A couple of platforms have some last-minute fixes, in particular: - riscv gets some fixes for noncoherent DMA on the renesas and thead platforms and dts fix for SPI on the visionfive 2 board - Qualcomm Snapdragon gets three dts fixes to address board specific regressions on the pmic and gpio nodes - Rockchip platforms get multiple dts fixes to address issues on the recent rk3399 platform as well as the older rk3128 platform that apparently regressed a while ago. - TI OMAP gets some trivial code and dts fixes and a regression fix for the omap1 ams-delta modem - NXP i.MX firmware has one fix for a use-after-free but in its error handling" * tag 'soc-fixes-6.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits) soc: renesas: ARCH_R9A07G043 depends on !RISCV_ISA_ZICBOM riscv: only select DMA_DIRECT_REMAP from RISCV_ISA_ZICBOM and ERRATA_THEAD_PBMT riscv: RISCV_NONSTANDARD_CACHE_OPS shouldn't depend on RISCV_DMA_NONCOHERENT riscv: dts: thead: set dma-noncoherent to soc bus arm64: dts: rockchip: Fix i2s0 pin conflict on ROCK Pi 4 boards arm64: dts: rockchip: Add i2s0-2ch-bus-bclk-off pins to RK3399 clk: ti: Fix missing omap5 mcbsp functional clock and aliases clk: ti: Fix missing omap4 mcbsp functional clock and aliases ARM: OMAP1: ams-delta: Fix MODEM initialization failure soc: renesas: Make ARCH_R9A07G043 depend on required options riscv: dts: starfive: visionfive 2: correct spi's ss pin firmware/imx-dsp: Fix use_after_free in imx_dsp_setup_channels() ARM: OMAP: timer32K: fix all kernel-doc warnings ARM: omap2: fix a debug printk ARM: dts: rockchip: Fix timer clocks for RK3128 ARM: dts: rockchip: Add missing quirk for RK3128's dma engine ARM: dts: rockchip: Add missing arm timer interrupt for RK3128 ARM: dts: rockchip: Fix i2c0 register address for RK3128 arm64: dts: rockchip: set codec system-clock-fixed on px30-ringneck-haikou arm64: dts: rockchip: use codec as clock master on px30-ringneck-haikou ...
2023-10-26Merge tag 'renesas-fixes-for-v6.6-tag3' of ↵Arnd Bergmann2-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes Renesas fixes for v6.6 (take three) - Sort out a few Kconfig dependency issues for the rich set of RISC-V non-coherent DMA support. * tag 'renesas-fixes-for-v6.6-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: soc: renesas: ARCH_R9A07G043 depends on !RISCV_ISA_ZICBOM riscv: only select DMA_DIRECT_REMAP from RISCV_ISA_ZICBOM and ERRATA_THEAD_PBMT riscv: RISCV_NONSTANDARD_CACHE_OPS shouldn't depend on RISCV_DMA_NONCOHERENT Link: https://lore.kernel.org/r/cover.1698312384.git.geert+renesas@glider.be Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2023-10-26riscv: only select DMA_DIRECT_REMAP from RISCV_ISA_ZICBOM and ERRATA_THEAD_PBMTChristoph Hellwig2-1/+2
RISCV_DMA_NONCOHERENT is also used for whacky non-standard non-coherent ops that use different hooks in dma-direct. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Tested-by: Samuel Holland <samuel.holland@sifive.com> Link: https://lore.kernel.org/r/20231018052654.50074-3-hch@lst.de Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2023-10-26riscv: RISCV_NONSTANDARD_CACHE_OPS shouldn't depend on RISCV_DMA_NONCOHERENTChristoph Hellwig1-1/+0
RISCV_NONSTANDARD_CACHE_OPS is also used for the pmem cache maintenance helpers, which are built into the kernel unconditionally. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20231018052654.50074-2-hch@lst.de Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2023-10-24Merge tag 'mm-hotfixes-stable-2023-10-24-09-40' of ↵Linus Torvalds2-7/+14
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm Pull misc fixes from Andrew Morton: "20 hotfixes. 12 are cc:stable and the remainder address post-6.5 issues or aren't considered necessary for earlier kernel versions" * tag 'mm-hotfixes-stable-2023-10-24-09-40' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: maple_tree: add GFP_KERNEL to allocations in mas_expected_entries() selftests/mm: include mman header to access MREMAP_DONTUNMAP identifier mailmap: correct email aliasing for Oleksij Rempel mailmap: map Bartosz's old address to the current one mm/damon/sysfs: check DAMOS regions update progress from before_terminate() MAINTAINERS: Ondrej has moved kasan: disable kasan_non_canonical_hook() for HW tags kasan: print the original fault addr when access invalid shadow hugetlbfs: close race between MADV_DONTNEED and page fault hugetlbfs: extend hugetlb_vma_lock to private VMAs hugetlbfs: clear resv_map pointer if mmap fails mm: zswap: fix pool refcount bug around shrink_worker() mm/migrate: fix do_pages_move for compat pointers riscv: fix set_huge_pte_at() for NAPOT mappings when a swap entry is set riscv: handle VM_FAULT_[HWPOISON|HWPOISON_LARGE] faults instead of panicking mmap: fix error paths with dup_anon_vma() mmap: fix vma_iterator in error path of vma_merge() mm: fix vm_brk_flags() to not bail out while holding lock mm/mempolicy: fix set_mempolicy_home_node() previous VMA pointer mm/page_alloc: correct start page when guard page debug is enabled
2023-10-17riscv: dts: thead: set dma-noncoherent to soc busJisheng Zhang1-0/+1
riscv select ARCH_DMA_DEFAULT_COHERENT by default, and th1520 isn't dma coherent, so set dma-noncoherent to reflect this fact. Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Tested-by: Drew Fustini <dfustini@baylibre.com> Reviewed-by: Guo Ren <guoren@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2023-10-17Merge tag 'riscv-dt-for-v6.6-final' of ↵Arnd Bergmann1-1/+1
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes RISC-V Devicetrees for v6.6-final A single fix for the Starfive VisionFive 2 platform so that chip select for SPI matches the vendor documentation. Signed-off-by: Conor Dooley <conor.dooley@microchip.com> * tag 'riscv-dt-for-v6.6-final' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: riscv: dts: starfive: visionfive 2: correct spi's ss pin Link: https://lore.kernel.org/r/20231015-outmatch-tragedy-228f91d396b5@spud Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2023-10-13Merge tag 'riscv-for-linus-6.6-rc6' of ↵Linus Torvalds9-35/+67
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V fixes from Palmer Dabbelt: - A handful of build fixes - A fix to avoid mixing up user/kernel-mode breakpoints, which can manifest as a hang when mixing k/uprobes with other breakpoint sources - A fix to avoid double-allocting crash kernel memory - A fix for tracefs syscall name mangling, which was causing syscalls not to show up in tracefs - A fix to the perf driver to enable the hw events when selected, which can trigger a BUG on some userspace access patterns * tag 'riscv-for-linus-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: drivers: perf: Fix panic in riscv SBI mmap support riscv: Fix ftrace syscall handling which are now prefixed with __riscv_ RISC-V: Fix wrong use of CONFIG_HAVE_SOFTIRQ_ON_OWN_STACK riscv: kdump: fix crashkernel reserving problem on RISC-V riscv: Remove duplicate objcopy flag riscv: signal: fix sigaltstack frame size checking riscv: errata: andes: Makefile: Fix randconfig build issue riscv: Only consider swbp/ss handlers for correct privileged mode riscv: kselftests: Fix mm build by removing testcases subdirectory
2023-10-12riscv: Fix ftrace syscall handling which are now prefixed with __riscv_Alexandre Ghiti1-0/+21
ftrace creates entries for each syscall in the tracefs but has failed since commit 08d0ce30e0e4 ("riscv: Implement syscall wrappers") which prefixes all riscv syscalls with __riscv_. So fix this by implementing arch_syscall_match_sym_name() which allows us to ignore this prefix. And also ignore compat syscalls like x86/arm64 by implementing arch_trace_is_compat_syscall(). Fixes: 08d0ce30e0e4 ("riscv: Implement syscall wrappers") Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Tested-by: Björn Töpel <bjorn@rivosinc.com> Link: https://lore.kernel.org/r/20231003182407.32198-1-alexghiti@rivosinc.com Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-10-12RISC-V: Fix wrong use of CONFIG_HAVE_SOFTIRQ_ON_OWN_STACKJiexun Wang1-2/+2
If configuration options SOFTIRQ_ON_OWN_STACK and PREEMPT_RT are enabled simultaneously under RISC-V architecture, it will result in a compilation failure: arch/riscv/kernel/irq.c:64:6: error: redefinition of 'do_softirq_own_stack' 64 | void do_softirq_own_stack(void) | ^~~~~~~~~~~~~~~~~~~~ In file included from ./arch/riscv/include/generated/asm/softirq_stack.h:1, from arch/riscv/kernel/irq.c:15: ./include/asm-generic/softirq_stack.h:8:20: note: previous definition of 'do_softirq_own_stack' was here 8 | static inline void do_softirq_own_stack(void) | ^~~~~~~~~~~~~~~~~~~~ After changing CONFIG_HAVE_SOFTIRQ_ON_OWN_STACK to CONFIG_SOFTIRQ_ON_OWN_STACK, compilation can be successful. Fixes: dd69d07a5a6c ("riscv: stack: Support HAVE_SOFTIRQ_ON_OWN_STACK") Reviewed-by: Guo Ren <guoren@kernel.org> Signed-off-by: Jiexun Wang <wangjiexun@tinylab.org> Reviewed-by: Samuel Holland <samuel@sholland.org> Link: https://lore.kernel.org/r/20230913052940.374686-1-wangjiexun@tinylab.org Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-10-12riscv: kdump: fix crashkernel reserving problem on RISC-VChen Jiahao1-13/+0
When testing on risc-v QEMU environment with "crashkernel=" parameter enabled, a problem occurred with the following message: [ 0.000000] crashkernel low memory reserved: 0xf8000000 - 0x100000000 (128 MB) [ 0.000000] crashkernel reserved: 0x0000000177e00000 - 0x0000000277e00000 (4096 MB) [ 0.000000] ------------[ cut here ]------------ [ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/resource.c:779 __insert_resource+0x8e/0xd0 [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 6.6.0-rc2-next-20230920 #1 [ 0.000000] Hardware name: riscv-virtio,qemu (DT) [ 0.000000] epc : __insert_resource+0x8e/0xd0 [ 0.000000] ra : insert_resource+0x28/0x4e [ 0.000000] epc : ffffffff80017344 ra : ffffffff8001742e sp : ffffffff81203db0 [ 0.000000] gp : ffffffff812ece98 tp : ffffffff8120dac0 t0 : ff600001f7ff2b00 [ 0.000000] t1 : 0000000000000000 t2 : 3428203030303030 s0 : ffffffff81203dc0 [ 0.000000] s1 : ffffffff81211e18 a0 : ffffffff81211e18 a1 : ffffffff81289380 [ 0.000000] a2 : 0000000277dfffff a3 : 0000000177e00000 a4 : 0000000177e00000 [ 0.000000] a5 : ffffffff81289380 a6 : 0000000277dfffff a7 : 0000000000000078 [ 0.000000] s2 : ffffffff81289380 s3 : ffffffff80a0bac8 s4 : ff600001f7ff2880 [ 0.000000] s5 : 0000000000000280 s6 : 8000000a00006800 s7 : 000000000000007f [ 0.000000] s8 : 0000000080017038 s9 : 0000000080038ea0 s10: 0000000000000000 [ 0.000000] s11: 0000000000000000 t3 : ffffffff80a0bc00 t4 : ffffffff80a0bc00 [ 0.000000] t5 : ffffffff80a0bbd0 t6 : ffffffff80a0bc00 [ 0.000000] status: 0000000200000100 badaddr: 0000000000000000 cause: 0000000000000003 [ 0.000000] [<ffffffff80017344>] __insert_resource+0x8e/0xd0 [ 0.000000] ---[ end trace 0000000000000000 ]--- [ 0.000000] Failed to add a Crash kernel resource at 177e00000 The crashkernel memory has been allocated successfully, whereas it failed to insert into iomem_resource. This is due to the unique reserving logic in risc-v arch specific code, i.e. crashk_res/crashk_low_res will be added into iomem_resource later in init_resources(), which is not aligned with current unified reserving logic in reserve_crashkernel_{generic,low}() and therefore leads to the failure of crashkernel reservation. Removing the arch specific code within #ifdef CONFIG_KEXEC_CORE in init_resources() to fix above problem. Fixes: 31549153088e ("riscv: kdump: use generic interface to simplify crashkernel reservation") Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com> Link: https://lore.kernel.org/r/20230925024333.730964-1-chenjiahao16@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-10-12riscv: Remove duplicate objcopy flagSong Shuai1-1/+0
There are two duplicate `-O binary` flags when objcopying from vmlinux to Image/xipImage. RISC-V set `-O binary` flag in both OBJCOPYFLAGS in the top-level riscv Makefile and OBJCOPYFLAGS_* in the boot/Makefile, and the objcopy cmd in Kbuild would join them together. The `-O binary` flag is only needed for objcopying Image, so remove the OBJCOPYFLAGS in the top-level riscv Makefile. Fixes: c0fbcd991860 ("RISC-V: Build flat and compressed kernel images") Signed-off-by: Song Shuai <songshuaishuai@tinylab.org> Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com> Link: https://lore.kernel.org/r/20230914091334.1458542-1-songshuaishuai@tinylab.org Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-10-12riscv: signal: fix sigaltstack frame size checkingAndy Chiu1-7/+0
The alternative stack checking in get_sigframe introduced by the Vector support is not needed and has a problem. It is not needed as we have already validate it at the beginning of the function if we are already on an altstack. If not, the size of an altstack is always validated at its allocation stage with sigaltstack_size_valid(). Besides, we must only regard the size of an altstack if the handler of a signal is registered with SA_ONSTACK. So, blindly checking overflow of an altstack if sas_ss_size not equals to zero will check against wrong signal handlers if only a subset of signals are registered with SA_ONSTACK. Fixes: 8ee0b41898fa ("riscv: signal: Add sigcontext save/restore for vector") Reported-by: Prashanth Swaminathan <prashanthsw@google.com> Signed-off-by: Andy Chiu <andy.chiu@sifive.com> Link: https://lore.kernel.org/r/20230822164904.21660-1-andy.chiu@sifive.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-10-12riscv: dts: starfive: visionfive 2: correct spi's ss pinNam Cao1-1/+1
The ss pin of spi0 is the same as sck pin. According to the visionfive 2 documentation, it should be pin 49 instead of 48. Fixes: 74fb20c8f05d ("riscv: dts: starfive: Add spi node and pins configuration") Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Signed-off-by: Nam Cao <namcao@linutronix.de> Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
2023-10-09riscv, bpf: Track both a0 (RISC-V ABI) and a5 (BPF) return valuesBjörn Töpel1-4/+9
The RISC-V BPF uses a5 for BPF return values, which are zero-extended, whereas the RISC-V ABI uses a0 which is sign-extended. In other words, a5 and a0 can differ, and are used in different context. The BPF trampoline are used for both BPF programs, and regular kernel functions. Make sure that the RISC-V BPF trampoline saves, and restores both a0 and a5. Fixes: 49b5e77ae3e2 ("riscv, bpf: Add bpf trampoline support for RV64") Signed-off-by: Björn Töpel <bjorn@rivosinc.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20231004120706.52848-3-bjorn@kernel.org
2023-10-09riscv, bpf: Sign-extend return valuesBjörn Töpel1-2/+3
The RISC-V architecture does not expose sub-registers, and hold all 32-bit values in a sign-extended format [1] [2]: | The compiler and calling convention maintain an invariant that all | 32-bit values are held in a sign-extended format in 64-bit | registers. Even 32-bit unsigned integers extend bit 31 into bits | 63 through 32. Consequently, conversion between unsigned and | signed 32-bit integers is a no-op, as is conversion from a signed | 32-bit integer to a signed 64-bit integer. While BPF, on the other hand, exposes sub-registers, and use zero-extension (similar to arm64/x86). This has led to some subtle bugs, where a BPF JITted program has not sign-extended the a0 register (return value in RISC-V land), passed the return value up the kernel, e.g.: | int from_bpf(void); | | long foo(void) | { | return from_bpf(); | } Here, a0 would be 0xffff_ffff, instead of the expected 0xffff_ffff_ffff_ffff. Internally, the RISC-V JIT uses a5 as a dedicated register for BPF return values. Keep a5 zero-extended, but explicitly sign-extend a0 (which is used outside BPF land). Now that a0 (RISC-V ABI) and a5 (BPF ABI) differs, a0 is only moved to a5 for non-BPF native calls (BPF_PSEUDO_CALL). Fixes: 2353ecc6f91f ("bpf, riscv: add BPF JIT for RV64G") Signed-off-by: Björn Töpel <bjorn@rivosinc.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://github.com/riscv/riscv-isa-manual/releases/download/riscv-isa-release-056b6ff-2023-10-02/unpriv-isa-asciidoc.pdf # [2] Link: https://github.com/riscv-non-isa/riscv-elf-psabi-doc/releases/download/draft-20230929-e5c800e661a53efe3c2678d71a306323b60eb13b/riscv-abi.pdf # [2] Link: https://lore.kernel.org/bpf/20231004120706.52848-2-bjorn@kernel.org
2023-10-07riscv: fix set_huge_pte_at() for NAPOT mappings when a swap entry is setAlexandre Ghiti1-6/+13
We used to determine the number of page table entries to set for a NAPOT hugepage by using the pte value which actually fails when the pte to set is a swap entry. So take advantage of a recent fix for arm64 reported in [1] which introduces the size of the mapping as an argument of set_huge_pte_at(): we can then use this size to compute the number of page table entries to set for a NAPOT region. Link: https://lkml.kernel.org/r/20230928151846.8229-3-alexghiti@rivosinc.com Fixes: 82a1a1f3bfb6 ("riscv: mm: support Svnapot in hugetlb page") Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com> Reported-by: Ryan Roberts <ryan.roberts@arm.com> Closes: https://lore.kernel.org/linux-arm-kernel/20230922115804.2043771-1-ryan.roberts@arm.com/ [1] Reviewed-by: Andrew Jones <ajones@ventanamicro.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Qinglin Pan <panqinglin2020@iscas.ac.cn> Cc: Conor Dooley <conor@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-10-07riscv: handle VM_FAULT_[HWPOISON|HWPOISON_LARGE] faults instead of panickingAlexandre Ghiti1-1/+1
Patch series "Fix set_huge_pte_at()". A recent report [1] from Ryan for arm64 revealed that we do not handle swap entries when setting a hugepage backed by a NAPOT region (the contpte riscv equivalent). As explained in [1], the issue was discovered by a new test in kselftest which uses poison entries, but the symptoms are different from arm64 though: - the riscv kernel bugs because we do not handle VM_FAULT_HWPOISON*, this is fixed by patch 1, - after that, the test passes because the first pte_napot() fails (the poison entry does not have the N bit set), and then we only set the first page table entry covering the NAPOT hugepage, which is enough for hugetlb_fault() to correctly raise a VM_FAULT_HWPOISON wherever we write in this mapping since only this first page table entry is checked (see https://elixir.bootlin.com/linux/v6.6-rc3/source/mm/hugetlb.c#L6071). But this seems fragile so patch 2 sets all page table entries of a NAPOT mapping. [1]: https://lore.kernel.org/linux-arm-kernel/20230922115804.2043771-1-ryan.roberts@arm.com/ This patch (of 2): We used to panic when such faults were encountered but we should handle those faults gracefully for userspace by sending a SIGBUS to the process, like most architectures do. Link: https://lkml.kernel.org/r/20230928151846.8229-1-alexghiti@rivosinc.com Link: https://lkml.kernel.org/r/20230928151846.8229-2-alexghiti@rivosinc.com Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com> Acked-by: Palmer Dabbelt <palmer@rivosinc.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Andrew Jones <ajones@ventanamicro.com> Cc: Conor Dooley <conor@kernel.org> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Qinglin Pan <panqinglin2020@iscas.ac.cn> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-10-01Merge tag 'mm-hotfixes-stable-2023-10-01-08-34' of ↵Linus Torvalds2-2/+4
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm Pull misc fixes from Andrew Morton: "Fourteen hotfixes, eleven of which are cc:stable. The remainder pertain to issues which were introduced after 6.5" * tag 'mm-hotfixes-stable-2023-10-01-08-34' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: Crash: add lock to serialize crash hotplug handling selftests/mm: fix awk usage in charge_reserved_hugetlb.sh and hugetlb_reparenting_test.sh that may cause error mm: mempolicy: keep VMA walk if both MPOL_MF_STRICT and MPOL_MF_MOVE are specified mm/damon/vaddr-test: fix memory leak in damon_do_test_apply_three_regions() mm, memcg: reconsider kmem.limit_in_bytes deprecation mm: zswap: fix potential memory corruption on duplicate store arm64: hugetlb: fix set_huge_pte_at() to work with all swap entries mm: hugetlb: add huge page size param to set_huge_pte_at() maple_tree: add MAS_UNDERFLOW and MAS_OVERFLOW states maple_tree: add mas_is_active() to detect in-tree walks nilfs2: fix potential use after free in nilfs_gccache_submit_read_data() mm: abstract moving to the next PFN mm: report success more often from filemap_map_folio_range() fs: binfmt_elf_efpic: fix personality for ELF-FDPIC
2023-10-01Merge tag 'soc-fixes-6.6' of ↵Linus Torvalds1-25/+26
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "These are the latest bug fixes that have come up in the soc tree. Most of these are fairly minor. Most notably, the majority of changes this time are not for dts files as usual. - Updates to the addresses of the broadcom and aspeed entries in the MAINTAINERS file. - Defconfig updates to address a regression on samsung and a build warning from an unknown Kconfig symbol - Build fixes for the StrongARM and Uniphier platforms - Code fixes for SCMI and FF-A firmware drivers, both of which had a simple bug that resulted in invalid data, and a lesser fix for the optee firmware driver - Multiple fixes for the recently added loongson/loongarch "guts" soc driver - Devicetree fixes for RISC-V on the startfive platform, addressing issues with NOR flash, usb and uart. - Multiple fixes for NXP i.MX8/i.MX9 dts files, fixing problems with clock, gpio, hdmi settings and the Makefile - Bug fixes for i.MX firmware code and the OCOTP soc driver - Multiple fixes for the TI sysc bus driver - Minor dts updates for TI omap dts files, to address boot time warnings and errors" * tag 'soc-fixes-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits) MAINTAINERS: Fix Florian Fainelli's email address arm64: defconfig: enable syscon-poweroff driver ARM: locomo: fix locomolcd_power declaration soc: loongson: loongson2_guts: Remove unneeded semicolon soc: loongson: loongson2_guts: Convert to devm_platform_ioremap_resource() soc: loongson: loongson_pm2: Populate children syscon nodes dt-bindings: soc: loongson,ls2k-pmc: Allow syscon-reboot/syscon-poweroff as child soc: loongson: loongson_pm2: Drop useless of_device_id compatible dt-bindings: soc: loongson,ls2k-pmc: Use fallbacks for ls2k-pmc compatible soc: loongson: loongson_pm2: Add dependency for INPUT arm64: defconfig: remove CONFIG_COMMON_CLK_NPCM8XX=y ARM: uniphier: fix cache kernel-doc warnings MAINTAINERS: aspeed: Update Andrew's email address MAINTAINERS: aspeed: Update git tree URL firmware: arm_ffa: Don't set the memory region attributes for MEM_LEND arm64: dts: imx: Add imx8mm-prt8mm.dtb to build arm64: dts: imx8mm-evk: Fix hdmi@3d node soc: imx8m: Enable OCOTP clock for imx8mm before reading registers arm64: dts: imx8mp-beacon-kit: Fix audio_pll2 clock arm64: dts: imx8mp: Fix SDMA2/3 clocks ...
2023-09-30mm: hugetlb: add huge page size param to set_huge_pte_at()Ryan Roberts2-2/+4
Patch series "Fix set_huge_pte_at() panic on arm64", v2. This series fixes a bug in arm64's implementation of set_huge_pte_at(), which can result in an unprivileged user causing a kernel panic. The problem was triggered when running the new uffd poison mm selftest for HUGETLB memory. This test (and the uffd poison feature) was merged for v6.5-rc7. Ideally, I'd like to get this fix in for v6.6 and I've cc'ed stable (correctly this time) to get it backported to v6.5, where the issue first showed up. Description of Bug ================== arm64's huge pte implementation supports multiple huge page sizes, some of which are implemented in the page table with multiple contiguous entries. So set_huge_pte_at() needs to work out how big the logical pte is, so that it can also work out how many physical ptes (or pmds) need to be written. It previously did this by grabbing the folio out of the pte and querying its size. However, there are cases when the pte being set is actually a swap entry. But this also used to work fine, because for huge ptes, we only ever saw migration entries and hwpoison entries. And both of these types of swap entries have a PFN embedded, so the code would grab that and everything still worked out. But over time, more calls to set_huge_pte_at() have been added that set swap entry types that do not embed a PFN. And this causes the code to go bang. The triggering case is for the uffd poison test, commit 99aa77215ad0 ("selftests/mm: add uffd unit test for UFFDIO_POISON"), which causes a PTE_MARKER_POISONED swap entry to be set, coutesey of commit 8a13897fb0da ("mm: userfaultfd: support UFFDIO_POISON for hugetlbfs") - added in v6.5-rc7. Although review shows that there are other call sites that set PTE_MARKER_UFFD_WP (which also has no PFN), these don't trigger on arm64 because arm64 doesn't support UFFD WP. If CONFIG_DEBUG_VM is enabled, we do at least get a BUG(), but otherwise, it will dereference a bad pointer in page_folio(): static inline struct folio *hugetlb_swap_entry_to_folio(swp_entry_t entry) { VM_BUG_ON(!is_migration_entry(entry) && !is_hwpoison_entry(entry)); return page_folio(pfn_to_page(swp_offset_pfn(entry))); } Fix === The simplest fix would have been to revert the dodgy cleanup commit 18f3962953e4 ("mm: hugetlb: kill set_huge_swap_pte_at()"), but since things have moved on, this would have required an audit of all the new set_huge_pte_at() call sites to see if they should be converted to set_huge_swap_pte_at(). As per the original intent of the change, it would also leave us open to future bugs when people invariably get it wrong and call the wrong helper. So instead, I've added a huge page size parameter to set_huge_pte_at(). This means that the arm64 code has the size in all cases. It's a bigger change, due to needing to touch the arches that implement the function, but it is entirely mechanical, so in my view, low risk. I've compile-tested all touched arches; arm64, parisc, powerpc, riscv, s390, sparc (and additionally x86_64). I've additionally booted and run mm selftests against arm64, where I observe the uffd poison test is fixed, and there are no other regressions. This patch (of 2): In order to fix a bug, arm64 needs to be told the size of the huge page for which the pte is being set in set_huge_pte_at(). Provide for this by adding an `unsigned long sz` parameter to the function. This follows the same pattern as huge_pte_clear(). This commit makes the required interface modifications to the core mm as well as all arches that implement this function (arm64, parisc, powerpc, riscv, s390, sparc). The actual arm64 bug will be fixed in a separate commit. No behavioral changes intended. Link: https://lkml.kernel.org/r/20230922115804.2043771-1-ryan.roberts@arm.com Link: https://lkml.kernel.org/r/20230922115804.2043771-2-ryan.roberts@arm.com Fixes: 8a13897fb0da ("mm: userfaultfd: support UFFDIO_POISON for hugetlbfs") Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> [powerpc 8xx] Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> [vmalloc change] Cc: Alexandre Ghiti <alex@ghiti.fr> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Alexander Gordeev <agordeev@linux.ibm.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christian Borntraeger <borntraeger@linux.ibm.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: David S. Miller <davem@davemloft.net> Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Peter Xu <peterx@redhat.com> Cc: Qi Zheng <zhengqi.arch@bytedance.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: SeongJae Park <sj@kernel.org> Cc: Sven Schnelle <svens@linux.ibm.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Cc: <stable@vger.kernel.org> [6.5+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-09-27riscv: errata: andes: Makefile: Fix randconfig build issueLad Prabhakar1-0/+4
Compile the andes errata with cflags set to " -mcmodel=medany" when CONFIG_RISCV_ALTERNATIVE_EARLY is enabled. Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202309111311.8tcq3KVc-lkp@intel.com/ Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Link: https://lore.kernel.org/r/20230925153844.26820-1-prabhakar.mahadev-lad.rj@bp.renesas.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-21RISC-V: KVM: Fix riscv_vcpu_get_isa_ext_single() for missing extensionsAnup Patel1-1/+4
The riscv_vcpu_get_isa_ext_single() should fail with -ENOENT error when corresponding ISA extension is not available on the host. Fixes: e98b1085be79 ("RISC-V: KVM: Factor-out ONE_REG related code to its own source file") Signed-off-by: Anup Patel <apatel@ventanamicro.com> Reviewed-by: Atish Patra <atishp@rivosinc.com> Reviewed-by: Andrew Jones <ajones@ventanamicro.com> Signed-off-by: Anup Patel <anup@brainfault.org>
2023-09-21RISC-V: KVM: Fix KVM_GET_REG_LIST API for ISA_EXT registersAnup Patel1-1/+1
The ISA_EXT registers to enabled/disable ISA extensions for VCPU are always available when underlying host has the corresponding ISA extension. The copy_isa_ext_reg_indices() called by the KVM_GET_REG_LIST API does not align with this expectation so let's fix it. Fixes: 031f9efafc08 ("KVM: riscv: Add KVM_GET_REG_LIST API support") Signed-off-by: Anup Patel <apatel@ventanamicro.com> Reviewed-by: Atish Patra <atishp@rivosinc.com> Reviewed-by: Andrew Jones <ajones@ventanamicro.com> Signed-off-by: Anup Patel <anup@brainfault.org>
2023-09-20riscv: Only consider swbp/ss handlers for correct privileged modeBjörn Töpel3-12/+40
RISC-V software breakpoint trap handlers are used for {k,u}probes. When trapping from kernelmode, only the kernelmode handlers should be considered. Vice versa, only usermode handlers for usermode traps. This is not the case on RISC-V, which can trigger a bug if a userspace process uses uprobes, and a WARN() is triggered from kernelmode (which is implemented via {c.,}ebreak). The kernel will trap on the kernelmode {c.,}ebreak, look for uprobes handlers, realize incorrectly that uprobes need to be handled, and exit the trap handler early. The trap returns to re-executing the {c.,}ebreak, and enter an infinite trap-loop. The issue was found running the BPF selftest [1]. Fix this issue by only considering the swbp/ss handlers for kernel/usermode respectively. Also, move CONFIG ifdeffery from traps.c to the asm/{k,u}probes.h headers. Note that linux/uprobes.h only include asm/uprobes.h if CONFIG_UPROBES is defined, which is why asm/uprobes.h needs to be unconditionally included in traps.c Link: https://lore.kernel.org/linux-riscv/87v8d19aun.fsf@all.your.base.are.belong.to.us/ # [1] Fixes: 74784081aac8 ("riscv: Add uprobes supported") Reviewed-by: Guo Ren <guoren@kernel.org> Reviewed-by: Nam Cao <namcaov@gmail.com> Tested-by: Puranjay Mohan <puranjay12@gmail.com> Signed-off-by: Björn Töpel <bjorn@rivosinc.com> Link: https://lore.kernel.org/r/20230912065619.62020-1-bjorn@kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-13riscv: dts: starfive: visionfive 2: Fix uart0 pins sort orderHal Feng1-24/+24
Node uart0_pins should be sorted alphabetically. Signed-off-by: Hal Feng <hal.feng@starfivetech.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
2023-09-13riscv: dts: starfive: visionfive 2: Enable usb0Hal Feng1-0/+1
usb0 was disabled by mistake when merging, so enable it. Fixes: e7c304c0346d ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm") Signed-off-by: Hal Feng <hal.feng@starfivetech.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
2023-09-12riscv: errata: fix T-Head dcache.cva encodingIcenowy Zheng1-2/+2
The dcache.cva encoding shown in the comments are wrong, it's for dcache.cval1 (which is restricted to L1) instead. Fix this in the comment and in the hardcoded instruction. Signed-off-by: Icenowy Zheng <uwu@icenowy.me> Tested-by: Sergey Matyukevich <sergey.matyukevich@syntacore.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Guo Ren <guoren@kernel.org> Tested-by: Drew Fustini <dfustini@baylibre.com> Link: https://lore.kernel.org/r/20230912072410.2481-1-jszhang@kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-12riscv: kexec: Align the kexeced kernel entrySong Shuai1-1/+7
The current riscv boot protocol requires 2MB alignment for RV64 and 4MB alignment for RV32. In KEXEC_FILE path, the elf_find_pbase() function should align the kexeced kernel entry according to the requirement, otherwise the kexeced kernel would silently BUG at the setup_vm(). Fixes: 8acea455fafa ("RISC-V: Support for kexec_file on panic") Signed-off-by: Song Shuai <songshuaishuai@tinylab.org> Link: https://lore.kernel.org/r/20230906095817.364390-1-songshuaishuai@tinylab.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-12riscv: dts: starfive: fix NOR flash reserved-data partition sizeAurelien Jarno1-1/+1
The Starfive VisionFive 2 has a 16MiB NOR flash, while the reserved-data partition is declared starting at address 0x600000 with a size of 0x1000000. This causes the kernel to output the following warning: [ 22.156589] mtd: partition "reserved-data" extends beyond the end of device "13010000.spi.0" -- size truncated to 0xa00000 It seems to be a confusion between the size of the partition and the end address. Fix that by specifying the right size. Fixes: 8384087a4223 ("riscv: dts: starfive: Add QSPI controller node for StarFive JH7110 SoC") Signed-off-by: Aurelien Jarno <aurelien@aurel32.net> Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
2023-09-10Merge tag 'riscv-for-linus-6.6-mw2-2' of ↵Linus Torvalds34-82/+907
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull more RISC-V updates from Palmer Dabbelt: - The kernel now dynamically probes for misaligned access speed, as opposed to relying on a table of known implementations. - Support for non-coherent devices on systems using the Andes AX45MP core, including the RZ/Five SoCs. - Support for the V extension in ptrace(), again. - Support for KASLR. - Support for the BPF prog pack allocator in RISC-V. - A handful of bug fixes and cleanups. * tag 'riscv-for-linus-6.6-mw2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (25 commits) soc: renesas: Kconfig: For ARCH_R9A07G043 select the required configs if dependencies are met riscv: Kconfig.errata: Add dependency for RISCV_SBI in ERRATA_ANDES config riscv: Kconfig.errata: Drop dependency for MMU in ERRATA_ANDES_CMO config riscv: Kconfig: Select DMA_DIRECT_REMAP only if MMU is enabled bpf, riscv: use prog pack allocator in the BPF JIT riscv: implement a memset like function for text riscv: extend patch_text_nosync() for multiple pages bpf: make bpf_prog_pack allocator portable riscv: libstub: Implement KASLR by using generic functions libstub: Fix compilation warning for rv32 arm64: libstub: Move KASLR handling functions to kaslr.c riscv: Dump out kernel offset information on panic riscv: Introduce virtual kernel mapping KASLR RISC-V: Add ptrace support for vectors soc: renesas: Kconfig: Select the required configs for RZ/Five SoC cache: Add L2 cache management for Andes AX45MP RISC-V core dt-bindings: cache: andestech,ax45mp-cache: Add DT binding documentation for L2 cache controller riscv: mm: dma-noncoherent: nonstandard cache operations support riscv: errata: Add Andes alternative ports riscv: asm: vendorid_list: Add Andes Technology to the vendors list ...
2023-09-08riscv: Kconfig.errata: Add dependency for RISCV_SBI in ERRATA_ANDES configLad Prabhakar1-1/+1
Andes errata uses sbi_ecalll() which is only available if RISCV_SBI is enabled. So add an dependency for RISCV_SBI in ERRATA_ANDES config to avoid any build failures. Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202308311610.ec6bm2G8-lkp@intel.com/ Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20230901110320.312674-1-prabhakar.mahadev-lad.rj@bp.renesas.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-08riscv: Kconfig.errata: Drop dependency for MMU in ERRATA_ANDES_CMO configLad Prabhakar1-1/+1
Now that RISCV_DMA_NONCOHERENT conditionally selects DMA_DIRECT_REMAP ie only if MMU is enabled, we no longer need the MMU dependency in ERRATA_ANDES_CMO config. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20230901105858.311745-1-prabhakar.mahadev-lad.rj@bp.renesas.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-08riscv: Kconfig: Select DMA_DIRECT_REMAP only if MMU is enabledLad Prabhakar1-1/+1
kernel/dma/mapping.c has its use of pgprot_dmacoherent() inside an #ifdef CONFIG_MMU block. kernel/dma/pool.c has its use of pgprot_dmacoherent() inside an #ifdef CONFIG_DMA_DIRECT_REMAP block. So select DMA_DIRECT_REMAP only if MMU is enabled for RISCV_DMA_NONCOHERENT config. This avoids users to explicitly select MMU. Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Link: https://lore.kernel.org/r/20230901105111.311200-1-prabhakar.mahadev-lad.rj@bp.renesas.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-08Merge patch series "bpf, riscv: use BPF prog pack allocator in BPF JIT"Palmer Dabbelt5-33/+251
Puranjay Mohan <puranjay12@gmail.com> says: Here is some data to prove the V2 fixes the problem: Without this series: root@rv-selftester:~/src/kselftest/bpf# time ./test_tag test_tag: OK (40945 tests) real 7m47.562s user 0m24.145s sys 6m37.064s With this series applied: root@rv-selftester:~/src/selftest/bpf# time ./test_tag test_tag: OK (40945 tests) real 7m29.472s user 0m25.865s sys 6m18.401s BPF programs currently consume a page each on RISCV. For systems with many BPF programs, this adds significant pressure to instruction TLB. High iTLB pressure usually causes slow down for the whole system. Song Liu introduced the BPF prog pack allocator[1] to mitigate the above issue. It packs multiple BPF programs into a single huge page. It is currently only enabled for the x86_64 BPF JIT. I enabled this allocator on the ARM64 BPF JIT[2]. It is being reviewed now. This patch series enables the BPF prog pack allocator for the RISCV BPF JIT. ====================================================== Performance Analysis of prog pack allocator on RISCV64 ====================================================== Test setup: =========== Host machine: Debian GNU/Linux 11 (bullseye) Qemu Version: QEMU emulator version 8.0.3 (Debian 1:8.0.3+dfsg-1) u-boot-qemu Version: 2023.07+dfsg-1 opensbi Version: 1.3-1 To test the performance of the BPF prog pack allocator on RV, a stresser tool[4] linked below was built. This tool loads 8 BPF programs on the system and triggers 5 of them in an infinite loop by doing system calls. The runner script starts 20 instances of the above which loads 8*20=160 BPF programs on the system, 5*20=100 of which are being constantly triggered. The script is passed a command which would be run in the above environment. The script was run with following perf command: ./run.sh "perf stat -a \ -e iTLB-load-misses \ -e dTLB-load-misses \ -e dTLB-store-misses \ -e instructions \ --timeout 60000" The output of the above command is discussed below before and after enabling the BPF prog pack allocator. The tests were run on qemu-system-riscv64 with 8 cpus, 16G memory. The rootfs was created using Bjorn's riscv-cross-builder[5] docker container linked below. Results ======= Before enabling prog pack allocator: ------------------------------------ Performance counter stats for 'system wide': 4939048 iTLB-load-misses 5468689 dTLB-load-misses 465234 dTLB-store-misses 1441082097998 instructions 60.045791200 seconds time elapsed After enabling prog pack allocator: ----------------------------------- Performance counter stats for 'system wide': 3430035 iTLB-load-misses 5008745 dTLB-load-misses 409944 dTLB-store-misses 1441535637988 instructions 60.046296600 seconds time elapsed Improvements in metrics ======================= It was expected that the iTLB-load-misses would decrease as now a single huge page is used to keep all the BPF programs compared to a single page for each program earlier. -------------------------------------------- The improvement in iTLB-load-misses: -30.5 % -------------------------------------------- I repeated this expriment more than 100 times in different setups and the improvement was always greater than 30%. This patch series is boot tested on the Starfive VisionFive 2 board[6]. The performance analysis was not done on the board because it doesn't expose iTLB-load-misses, etc. The stresser program was run on the board to test the loading and unloading of BPF programs [1] https://lore.kernel.org/bpf/20220204185742.271030-1-song@kernel.org/ [2] https://lore.kernel.org/all/20230626085811.3192402-1-puranjay12@gmail.com/ [3] https://lore.kernel.org/all/20230626085811.3192402-2-puranjay12@gmail.com/ [4] https://github.com/puranjaymohan/BPF-Allocator-Bench [5] https://github.com/bjoto/riscv-cross-builder [6] https://www.starfivetech.com/en/site/boards * b4-shazam-merge: bpf, riscv: use prog pack allocator in the BPF JIT riscv: implement a memset like function for text riscv: extend patch_text_nosync() for multiple pages bpf: make bpf_prog_pack allocator portable Link: https://lore.kernel.org/r/20230831131229.497941-1-puranjay12@gmail.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-08Merge patch series "riscv: Introduce KASLR"Palmer Dabbelt9-2/+129
Alexandre Ghiti <alexghiti@rivosinc.com> says: The following KASLR implementation allows to randomize the kernel mapping: - virtually: we expect the bootloader to provide a seed in the device-tree - physically: only implemented in the EFI stub, it relies on the firmware to provide a seed using EFI_RNG_PROTOCOL. arm64 has a similar implementation hence the patch 3 factorizes KASLR related functions for riscv to take advantage. The new virtual kernel location is limited by the early page table that only has one PUD and with the PMD alignment constraint, the kernel can only take < 512 positions. * b4-shazam-merge: riscv: libstub: Implement KASLR by using generic functions libstub: Fix compilation warning for rv32 arm64: libstub: Move KASLR handling functions to kaslr.c riscv: Dump out kernel offset information on panic riscv: Introduce virtual kernel mapping KASLR Link: https://lore.kernel.org/r/20230722123850.634544-1-alexghiti@rivosinc.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-08Merge patch "RISC-V: Add ptrace support for vectors"Palmer Dabbelt2-4/+88
This resurrects the vector ptrace() support that was removed for 6.5 due to some bugs cropping up as part of the GDB review process. * b4-shazam-merge: RISC-V: Add ptrace support for vectors Link: https://lore.kernel.org/r/20230825050248.32681-1-andy.chiu@sifive.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-08Merge patch series "Add non-coherent DMA support for AX45MP"Palmer Dabbelt12-0/+194
Prabhakar <prabhakar.csengg@gmail.com> says: From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> non-coherent DMA support for AX45MP ==================================== On the Andes AX45MP core, cache coherency is a specification option so it may not be supported. In this case DMA will fail. To get around with this issue this patch series does the below: 1] Andes alternative ports is implemented as errata which checks if the IOCP is missing and only then applies to CMO errata. One vendor specific SBI EXT (ANDES_SBI_EXT_IOCP_SW_WORKAROUND) is implemented as part of errata. Below are the configs which Andes port provides (and are selected by RZ/Five): - ERRATA_ANDES - ERRATA_ANDES_CMO OpenSBI patch supporting ANDES_SBI_EXT_IOCP_SW_WORKAROUND SBI is now part v1.3 release. 2] Andes AX45MP core has a Programmable Physical Memory Attributes (PMA) block that allows dynamic adjustment of memory attributes in the runtime. It contains a configurable amount of PMA entries implemented as CSR registers to control the attributes of memory locations in interest. OpenSBI configures the PMA regions as required and creates a reserve memory node and propagates it to the higher boot stack. Currently OpenSBI (upstream) configures the required PMA region and passes this a shared DMA pool to Linux. reserved-memory { #address-cells = <2>; #size-cells = <2>; ranges; pma_resv0@58000000 { compatible = "shared-dma-pool"; reg = <0x0 0x58000000 0x0 0x08000000>; no-map; linux,dma-default; }; }; The above shared DMA pool gets appended to Linux DTB so the DMA memory requests go through this region. 3] We provide callbacks to synchronize specific content between memory and cache. 4] RZ/Five SoC selects the below configs - AX45MP_L2_CACHE - DMA_GLOBAL_POOL - ERRATA_ANDES - ERRATA_ANDES_CMO ----------x---------------------x--------------------x---------------x---- * b4-shazam-merge: soc: renesas: Kconfig: Select the required configs for RZ/Five SoC cache: Add L2 cache management for Andes AX45MP RISC-V core dt-bindings: cache: andestech,ax45mp-cache: Add DT binding documentation for L2 cache controller riscv: mm: dma-noncoherent: nonstandard cache operations support riscv: errata: Add Andes alternative ports riscv: asm: vendorid_list: Add Andes Technology to the vendors list Link: https://lore.kernel.org/r/20230818135723.80612-1-prabhakar.mahadev-lad.rj@bp.renesas.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-08Merge patch series "riscv: dma-mapping: unify support for cache flushes"Palmer Dabbelt1-9/+51
Prabhakar <prabhakar.csengg@gmail.com> says: From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> This patch series is a subset from Arnd's original series [0]. Ive just picked up the bits required for RISC-V unification of cache flushing. Remaining patches from the series [0] will be taken care by Arnd soon. * b4-shazam-merge: riscv: dma-mapping: switch over to generic implementation riscv: dma-mapping: skip invalidation before bidirectional DMA riscv: dma-mapping: only invalidate after DMA, not flush Link: https://lore.kernel.org/r/20230816232336.164413-1-prabhakar.mahadev-lad.rj@bp.renesas.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-08Merge patch series "RISC-V: Probe for misaligned access speed"Palmer Dabbelt9-33/+193
Evan Green <evan@rivosinc.com> says: The current setting for the hwprobe bit indicating misaligned access speed is controlled by a vendor-specific feature probe function. This is essentially a per-SoC table we have to maintain on behalf of each vendor going forward. Let's convert that instead to something we detect at runtime. We have two assembly routines at the heart of our probe: one that does a bunch of word-sized accesses (without aligning its input buffer), and the other that does byte accesses. If we can move a larger number of bytes using misaligned word accesses than we can with the same amount of time doing byte accesses, then we can declare misaligned accesses as "fast". The tradeoff of reducing this maintenance burden is boot time. We spend 4-6 jiffies per core doing this measurement (0-2 on jiffie edge alignment, and 4 on measurement). The timing loop was based on raid6_choose_gen(), which uses (16+1)*N jiffies (where N is the number of algorithms). By taking only the fastest iteration out of all attempts for use in the comparison, variance between runs is very low. On my THead C906, it looks like this: [ 0.047563] cpu0: Ratio of byte access time to unaligned word access is 4.34, unaligned accesses are fast Several others have chimed in with results on slow machines with the older algorithm, which took all runs into account, including noise like interrupts. Even with this variation, results indicate that in all cases (fast, slow, and emulated) the measured numbers are nowhere near each other (always multiple factors away). * b4-shazam-merge: RISC-V: alternative: Remove feature_probe_func RISC-V: Probe for unaligned access speed Link: https://lore.kernel.org/r/20230818194136.4084400-1-evan@rivosinc.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-07Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds13-596/+1159
Pull kvm updates from Paolo Bonzini: "ARM: - Clean up vCPU targets, always returning generic v8 as the preferred target - Trap forwarding infrastructure for nested virtualization (used for traps that are taken from an L2 guest and are needed by the L1 hypervisor) - FEAT_TLBIRANGE support to only invalidate specific ranges of addresses when collapsing a table PTE to a block PTE. This avoids that the guest refills the TLBs again for addresses that aren't covered by the table PTE. - Fix vPMU issues related to handling of PMUver. - Don't unnecessary align non-stack allocations in the EL2 VA space - Drop HCR_VIRT_EXCP_MASK, which was never used... - Don't use smp_processor_id() in kvm_arch_vcpu_load(), but the cpu parameter instead - Drop redundant call to kvm_set_pfn_accessed() in user_mem_abort() - Remove prototypes without implementations RISC-V: - Zba, Zbs, Zicntr, Zicsr, Zifencei, and Zihpm support for guest - Added ONE_REG interface for SATP mode - Added ONE_REG interface to enable/disable multiple ISA extensions - Improved error codes returned by ONE_REG interfaces - Added KVM_GET_REG_LIST ioctl() implementation for KVM RISC-V - Added get-reg-list selftest for KVM RISC-V s390: - PV crypto passthrough enablement (Tony, Steffen, Viktor, Janosch) Allows a PV guest to use crypto cards. Card access is governed by the firmware and once a crypto queue is "bound" to a PV VM every other entity (PV or not) looses access until it is not bound anymore. Enablement is done via flags when creating the PV VM. - Guest debug fixes (Ilya) x86: - Clean up KVM's handling of Intel architectural events - Intel bugfixes - Add support for SEV-ES DebugSwap, allowing SEV-ES guests to use debug registers and generate/handle #DBs - Clean up LBR virtualization code - Fix a bug where KVM fails to set the target pCPU during an IRTE update - Fix fatal bugs in SEV-ES intrahost migration - Fix a bug where the recent (architecturally correct) change to reinject #BP and skip INT3 broke SEV guests (can't decode INT3 to skip it) - Retry APIC map recalculation if a vCPU is added/enabled - Overhaul emergency reboot code to bring SVM up to par with VMX, tie the "emergency disabling" behavior to KVM actually being loaded, and move all of the logic within KVM - Fix user triggerable WARNs in SVM where KVM incorrectly assumes the TSC ratio MSR cannot diverge from the default when TSC scaling is disabled up related code - Add a framework to allow "caching" feature flags so that KVM can check if the guest can use a feature without needing to search guest CPUID - Rip out the ancient MMU_DEBUG crud and replace the useful bits with CONFIG_KVM_PROVE_MMU - Fix KVM's handling of !visible guest roots to avoid premature triple fault injection - Overhaul KVM's page-track APIs, and KVMGT's usage, to reduce the API surface that is needed by external users (currently only KVMGT), and fix a variety of issues in the process Generic: - Wrap kvm_{gfn,hva}_range.pte in a union to allow mmu_notifier events to pass action specific data without needing to constantly update the main handlers. - Drop unused function declarations Selftests: - Add testcases to x86's sync_regs_test for detecting KVM TOCTOU bugs - Add support for printf() in guest code and covert all guest asserts to use printf-based reporting - Clean up the PMU event filter test and add new testcases - Include x86 selftests in the KVM x86 MAINTAINERS entry" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (279 commits) KVM: x86/mmu: Include mmu.h in spte.h KVM: x86/mmu: Use dummy root, backed by zero page, for !visible guest roots KVM: x86/mmu: Disallow guest from using !visible slots for page tables KVM: x86/mmu: Harden TDP MMU iteration against root w/o shadow page KVM: x86/mmu: Harden new PGD against roots without shadow pages KVM: x86/mmu: Add helper to convert root hpa to shadow page drm/i915/gvt: Drop final dependencies on KVM internal details KVM: x86/mmu: Handle KVM bookkeeping in page-track APIs, not callers KVM: x86/mmu: Drop @slot param from exported/external page-track APIs KVM: x86/mmu: Bug the VM if write-tracking is used but not enabled KVM: x86/mmu: Assert that correct locks are held for page write-tracking KVM: x86/mmu: Rename page-track APIs to reflect the new reality KVM: x86/mmu: Drop infrastructure for multiple page-track modes KVM: x86/mmu: Use page-track notifiers iff there are external users KVM: x86/mmu: Move KVM-only page-track declarations to internal header KVM: x86: Remove the unused page-track hook track_flush_slot() drm/i915/gvt: switch from ->track_flush_slot() to ->track_remove_region() KVM: x86: Add a new page-track hook to handle memslot deletion drm/i915/gvt: Don't bother removing write-protection on to-be-deleted slot KVM: x86: Reject memslot MOVE operations if KVMGT is attached ...
2023-09-06bpf, riscv: use prog pack allocator in the BPF JITPuranjay Mohan3-28/+141
Use bpf_jit_binary_pack_alloc() for memory management of JIT binaries in RISCV BPF JIT. The bpf_jit_binary_pack_alloc creates a pair of RW and RX buffers. The JIT writes the program into the RW buffer. When the JIT is done, the program is copied to the final RX buffer with bpf_jit_binary_pack_finalize. Implement bpf_arch_text_copy() and bpf_arch_text_invalidate() for RISCV JIT as these functions are required by bpf_jit_binary_pack allocator. Signed-off-by: Puranjay Mohan <puranjay12@gmail.com> Reviewed-by: Song Liu <song@kernel.org> Reviewed-by: Pu Lehui <pulehui@huawei.com> Acked-by: Björn Töpel <bjorn@kernel.org> Tested-by: Björn Töpel <bjorn@rivosinc.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/r/20230831131229.497941-5-puranjay12@gmail.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-06riscv: implement a memset like function for textPuranjay Mohan2-0/+78
The BPF JIT needs to write invalid instructions to RX regions of memory to invalidate removed BPF programs. This needs a function like memset() that can work with RX memory. Implement patch_text_set_nosync() which is similar to text_poke_set() of x86. Signed-off-by: Puranjay Mohan <puranjay12@gmail.com> Reviewed-by: Pu Lehui <pulehui@huawei.com> Acked-by: Björn Töpel <bjorn@kernel.org> Tested-by: Björn Töpel <bjorn@rivosinc.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/r/20230831131229.497941-4-puranjay12@gmail.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-06riscv: extend patch_text_nosync() for multiple pagesPuranjay Mohan1-5/+32
The patch_insn_write() function currently doesn't work for multiple pages of instructions, therefore patch_text_nosync() will fail with a page fault if called with lengths spanning multiple pages. This commit extends the patch_insn_write() function to support multiple pages by copying at max 2 pages at a time in a loop. This implementation is similar to text_poke_copy() function of x86. Signed-off-by: Puranjay Mohan <puranjay12@gmail.com> Reviewed-by: Pu Lehui <pulehui@huawei.com> Reviewed-by: Björn Töpel <bjorn@rivosinc.com> Tested-by: Björn Töpel <bjorn@rivosinc.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/r/20230831131229.497941-3-puranjay12@gmail.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-06riscv: libstub: Implement KASLR by using generic functionsAlexandre Ghiti2-0/+3
We can now use arm64 functions to handle the move of the kernel physical mapping: if KASLR is enabled, we will try to get a random seed from the firmware, if not possible, the kernel will be moved to a location that suits its alignment constraints. Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com> Tested-by: Conor Dooley <conor.dooley@microchip.com> Tested-by: Song Shuai <songshuaishuai@tinylab.org> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Sami Tolvanen <samitolvanen@google.com> Link: https://lore.kernel.org/r/20230722123850.634544-6-alexghiti@rivosinc.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-06riscv: Dump out kernel offset information on panicAlexandre Ghiti1-0/+25
Dump out the KASLR virtual kernel offset when panic to help debug kernel. Signed-off-by: Zong Li <zong.li@sifive.com> Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com> Tested-by: Conor Dooley <conor.dooley@microchip.com> Tested-by: Song Shuai <songshuaishuai@tinylab.org> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Sami Tolvanen <samitolvanen@google.com> Link: https://lore.kernel.org/r/20230722123850.634544-3-alexghiti@rivosinc.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-06riscv: Introduce virtual kernel mapping KASLRAlexandre Ghiti6-2/+101
KASLR implementation relies on a relocatable kernel so that we can move the kernel mapping. The seed needed to virtually move the kernel is taken from the device tree, so we rely on the bootloader to provide a correct seed. Zkr could be used unconditionnally instead if implemented, but that's for another patch. Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com> Tested-by: Conor Dooley <conor.dooley@microchip.com> Tested-by: Song Shuai <songshuaishuai@tinylab.org> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Sami Tolvanen <samitolvanen@google.com> Link: https://lore.kernel.org/r/20230722123850.634544-2-alexghiti@rivosinc.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2023-09-05Merge tag 'kbuild-v6.6' of ↵Linus Torvalds2-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild updates from Masahiro Yamada: - Enable -Wenum-conversion warning option - Refactor the rpm-pkg target - Fix scripts/setlocalversion to consider annotated tags for rt-kernel - Add a jump key feature for the search menu of 'make nconfig' - Support Qt6 for 'make xconfig' - Enable -Wformat-overflow, -Wformat-truncation, -Wstringop-overflow, and -Wrestrict warnings for W=1 builds - Replace <asm/export.h> with <linux/export.h> for alpha, ia64, and sparc - Support DEB_BUILD_OPTIONS=parallel=N for the debian source package - Refactor scripts/Makefile.modinst and fix some modules_sign issues - Add a new Kconfig env variable to warn symbols that are not defined anywhere - Show help messages of config fragments in 'make help' * tag 'kbuild-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (62 commits) kconfig: fix possible buffer overflow kbuild: Show marked Kconfig fragments in "help" kconfig: add warn-unknown-symbols sanity check kbuild: dummy-tools: make MPROFILE_KERNEL checks work on BE Documentation/llvm: refresh docs modpost: Skip .llvm.call-graph-profile section check kbuild: support modules_sign for external modules as well kbuild: support 'make modules_sign' with CONFIG_MODULE_SIG_ALL=n kbuild: move more module installation code to scripts/Makefile.modinst kbuild: reduce the number of mkdir calls during modules_install kbuild: remove $(MODLIB)/source symlink kbuild: move depmod rule to scripts/Makefile.modinst kbuild: add modules_sign to no-{compiler,sync-config}-targets kbuild: do not run depmod for 'make modules_sign' kbuild: deb-pkg: support DEB_BUILD_OPTIONS=parallel=N in debian/rules alpha: remove <asm/export.h> alpha: replace #include <asm/export.h> with #include <linux/export.h> ia64: remove <asm/export.h> ia64: replace #include <asm/export.h> with #include <linux/export.h> sparc: remove <asm/export.h> ...
2023-09-03kbuild: Show marked Kconfig fragments in "help"Kees Cook2-0/+2
Currently the Kconfig fragments in kernel/configs and arch/*/configs that aren't used internally aren't discoverable through "make help", which consists of hard-coded lists of config fragments. Instead, list all the fragment targets that have a "# Help: " comment prefix so the targets can be generated dynamically. Add logic to the Makefile to search for and display the fragment and comment. Add comments to fragments that are intended to be direct targets. Signed-off-by: Kees Cook <keescook@chromium.org> Co-developed-by: Masahiro Yamada <masahiroy@kernel.org> Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc) Reviewed-by: Nicolas Schier <nicolas@fjasle.eu> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2023-09-01RISC-V: Add ptrace support for vectorsAndy Chiu2-4/+88
This patch add back the ptrace support with the following fix: - Define NT_RISCV_CSR and re-number NT_RISCV_VECTOR to prevent conflicting with gdb's NT_RISCV_CSR. - Use struct __riscv_v_regset_state to handle ptrace requests Since gdb does not directly include the note description header in Linux and has already defined NT_RISCV_CSR as 0x900, we decide to sync with gdb and renumber NT_RISCV_VECTOR to solve and prevent future conflicts. Fixes: 0c59922c769a ("riscv: Add ptrace vector support") Signed-off-by: Andy Chiu <andy.chiu@sifive.com> Link: https://lore.kernel.org/r/20230825050248.32681-1-andy.chiu@sifive.com [Palmer: Drop the unused "size" variable in riscv_vr_set().] Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>