| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Control register handling has nothing to do with low level SMP code.
Move it to a separate file.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
__cmpxchg_user_key() uses 128 bit types which, depending on compiler
and config options, may lead to an __ashlti3() library call.
Get rid of that by simply casting the 128 bit values to 32 bit values.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Fixes: 51098f0eb22e ("s390/cmpxchg: make loop condition for 1,2 byte cases precise")
Link: https://lore.kernel.org/all/4b96b112d5415d08a81d30657feec2c8c3000f7c.camel@linux.ibm.com/
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
cmpxchg_user_key() for byte and short values is implemented via a one word
cmpxchg loop. Give up trying to perform the cmpxchg if it fails too often
because of contention on the cache line. This ensures that the thread
cannot become stuck in the kernel.
Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Link: https://lore.kernel.org/r/20221117100745.3253896-1-scgl@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The cmpxchg implementation for 1 and 2 bytes consists of a 4 byte
cmpxchg loop. Currently, the decision to retry is imprecise, looping if
bits outside the target byte(s) change instead of retrying until the
target byte(s) differ from the old value.
E.g. if an attempt to exchange (prev_left_0 old_bytes prev_right_0) is
made and it fails because the word at the address is
(prev_left_1 x prev_right_1) where both x != old_bytes and one of the
prev_*_1 values differs from the respective prev_*_0 value, the cmpxchg
is retried, even if by a semantic equivalent to a normal cmpxchg, the
exchange would fail.
Instead exit the loop if x != old_bytes and retry otherwise.
Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Link: https://lore.kernel.org/r/20221116144711.3811011-1-scgl@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Add cmpxchg_user_key() which allows to execute a compare and exchange
on a user space address. This allows also to specify a storage key
which makes sure that key-controlled protection is considered.
This is based on a patch written by Janis Schoetterl-Glausch.
Link: https://lore.kernel.org/all/20220930210751.225873-2-scgl@linux.ibm.com
Cc: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Link: https://lore.kernel.org/r/Y2J8axs+bcQ2dO/l@osiris
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Alexander Gordeev:
- Rework copy_oldmem_page() callback to take an iov_iter.
This includes a few prerequisite updates and fixes to the oldmem
reading code.
- Rework cpufeature implementation to allow for various CPU feature
indications, which is not only limited to hardware capabilities, but
also allows CPU facilities.
- Use the cpufeature rework to autoload Ultravisor module when CPU
facility 158 is available.
- Add ELF note type for encrypted CPU state of a protected virtual CPU.
The zgetdump tool from s390-tools package will decrypt the CPU state
using a Customer Communication Key and overwrite respective notes to
make the data accessible for crash and other debugging tools.
- Use vzalloc() instead of vmalloc() + memset() in ChaCha20 crypto
test.
- Fix incorrect recovery of kretprobe modified return address in
stacktrace.
- Switch the NMI handler to use generic irqentry_nmi_enter() and
irqentry_nmi_exit() helper functions.
- Rework the cryptographic Adjunct Processors (AP) pass-through design
to support dynamic changes to the AP matrix of a running guest as
well as to implement more of the AP architecture.
- Minor boot code cleanups.
- Grammar and typo fixes to hmcdrv and tape drivers.
* tag 's390-5.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (46 commits)
Revert "s390/smp: enforce lowcore protection on CPU restart"
Revert "s390/smp: rework absolute lowcore access"
Revert "s390/smp,ptdump: add absolute lowcore markers"
s390/unwind: fix fgraph return address recovery
s390/nmi: use irqentry_nmi_enter()/irqentry_nmi_exit()
s390: add ELF note type for encrypted CPU state of a PV VCPU
s390/smp,ptdump: add absolute lowcore markers
s390/smp: rework absolute lowcore access
s390/setup: rearrange absolute lowcore initialization
s390/boot: cleanup adjust_to_uv_max() function
s390/smp: enforce lowcore protection on CPU restart
s390/tape: fix comment typo
s390/hmcdrv: fix Kconfig "its" grammar
s390/docs: fix warnings for vfio_ap driver doc
s390/docs: fix warnings for vfio_ap driver lock usage doc
s390/crash: support multi-segment iterators
s390/crash: use static swap buffer for copy_to_user_real()
s390/crash: move copy_to_user_real() to crash_dump.c
s390/zcore: fix race when reading from hardware system area
s390/crash: fix incorrect number of bytes to copy to user space
...
|
|
Function copy_to_user_real() does not really belong to maccess.c.
It is only used for copying oldmem to user space, so let's move
it to the friends.
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Link: https://lore.kernel.org/r/e8de968d40202d87caa09aef12e9c67ec23a1c1a.1658206891.git.agordeev@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
it's inline and unlikely() inside of it (including the implicit one
in WARN_ON_ONCE()) suffice to convince the compiler that getting
false from check_copy_size() is unlikely.
Spotted-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Whitespace cleanup to get rid if some checkpatch findings, but mainly
to have consistent coding style within the header file again.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Historically the uaccess code pre-initializes the result of get_user()
(and now also __get_kernel_nofault()) to zero and uses the result as
input parameter for inline assemblies. This is different to what most,
if not all, other architectures are doing, which set the result to
zero within the exception handler in case of a fault.
Use the new extable mechanism and handle zeroing of the result within
the exception handler in case of a fault.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Make code easier to read by using symbolic names.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Raise minimum supported machine generation to z10, which comes with
various cleanups and code simplifications (usercopy/spectre
mitigation/etc).
- Rework extables and get rid of anonymous out-of-line fixups.
- Page table helpers cleanup. Add set_pXd()/set_pte() helper functions.
Covert pte_val()/pXd_val() macros to functions.
- Optimize kretprobe handling by avoiding extra kprobe on
__kretprobe_trampoline.
- Add support for CEX8 crypto cards.
- Allow to trigger AP bus rescan via writing to /sys/bus/ap/scans.
- Add CONFIG_EXPOLINE_EXTERN option to build the kernel without COMDAT
group sections which simplifies kpatch support.
- Always use the packed stack layout and extend kernel unwinder tests.
- Add sanity checks for ftrace code patching.
- Add s390dbf debug log for the vfio_ap device driver.
- Various virtual vs physical address confusion fixes.
- Various small fixes and improvements all over the code.
* tag 's390-5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (69 commits)
s390/test_unwind: add kretprobe tests
s390/kprobes: Avoid additional kprobe in kretprobe handling
s390: convert ".insn" encoding to instruction names
s390: assume stckf is always present
s390/nospec: move to single register thunks
s390: raise minimum supported machine generation to z10
s390/uaccess: Add copy_from/to_user_key functions
s390/nospec: align and size extern thunks
s390/nospec: add an option to use thunk-extern
s390/nospec: generate single register thunks if possible
s390/pci: make zpci_set_irq()/zpci_clear_irq() static
s390: remove unused expoline to BC instructions
s390/irq: use assignment instead of cast
s390/traps: get rid of magic cast for per code
s390/traps: get rid of magic cast for program interruption code
s390/signal: fix typo in comments
s390/asm-offsets: remove unused defines
s390/test_unwind: avoid build warning with W=1
s390: remove .fixup section
s390/bpf: encode register within extable entry
...
|
|
Pull kvm updates from Paolo Bonzini:
"ARM:
- Proper emulation of the OSLock feature of the debug architecture
- Scalibility improvements for the MMU lock when dirty logging is on
- New VMID allocator, which will eventually help with SVA in VMs
- Better support for PMUs in heterogenous systems
- PSCI 1.1 support, enabling support for SYSTEM_RESET2
- Implement CONFIG_DEBUG_LIST at EL2
- Make CONFIG_ARM64_ERRATUM_2077057 default y
- Reduce the overhead of VM exit when no interrupt is pending
- Remove traces of 32bit ARM host support from the documentation
- Updated vgic selftests
- Various cleanups, doc updates and spelling fixes
RISC-V:
- Prevent KVM_COMPAT from being selected
- Optimize __kvm_riscv_switch_to() implementation
- RISC-V SBI v0.3 support
s390:
- memop selftest
- fix SCK locking
- adapter interruptions virtualization for secure guests
- add Claudio Imbrenda as maintainer
- first step to do proper storage key checking
x86:
- Continue switching kvm_x86_ops to static_call(); introduce
static_call_cond() and __static_call_ret0 when applicable.
- Cleanup unused arguments in several functions
- Synthesize AMD 0x80000021 leaf
- Fixes and optimization for Hyper-V sparse-bank hypercalls
- Implement Hyper-V's enlightened MSR bitmap for nested SVM
- Remove MMU auditing
- Eager splitting of page tables (new aka "TDP" MMU only) when dirty
page tracking is enabled
- Cleanup the implementation of the guest PGD cache
- Preparation for the implementation of Intel IPI virtualization
- Fix some segment descriptor checks in the emulator
- Allow AMD AVIC support on systems with physical APIC ID above 255
- Better API to disable virtualization quirks
- Fixes and optimizations for the zapping of page tables:
- Zap roots in two passes, avoiding RCU read-side critical
sections that last too long for very large guests backed by 4
KiB SPTEs.
- Zap invalid and defunct roots asynchronously via
concurrency-managed work queue.
- Allowing yielding when zapping TDP MMU roots in response to the
root's last reference being put.
- Batch more TLB flushes with an RCU trick. Whoever frees the
paging structure now holds RCU as a proxy for all vCPUs running
in the guest, i.e. to prolongs the grace period on their behalf.
It then kicks the the vCPUs out of guest mode before doing
rcu_read_unlock().
Generic:
- Introduce __vcalloc and use it for very large allocations that need
memcg accounting"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (246 commits)
KVM: use kvcalloc for array allocations
KVM: x86: Introduce KVM_CAP_DISABLE_QUIRKS2
kvm: x86: Require const tsc for RT
KVM: x86: synthesize CPUID leaf 0x80000021h if useful
KVM: x86: add support for CPUID leaf 0x80000021
KVM: x86: do not use KVM_X86_OP_OPTIONAL_RET0 for get_mt_mask
Revert "KVM: x86/mmu: Zap only TDP MMU leafs in kvm_zap_gfn_range()"
kvm: x86/mmu: Flush TLB before zap_gfn_range releases RCU
KVM: arm64: fix typos in comments
KVM: arm64: Generalise VM features into a set of flags
KVM: s390: selftests: Add error memop tests
KVM: s390: selftests: Add more copy memop tests
KVM: s390: selftests: Add named stages for memop test
KVM: s390: selftests: Add macro as abstraction for MEM_OP
KVM: s390: selftests: Split memop tests
KVM: s390x: fix SCK locking
RISC-V: KVM: Implement SBI HSM suspend call
RISC-V: KVM: Add common kvm_riscv_vcpu_wfi() function
RISC-V: Add SBI HSM suspend related defines
RISC-V: KVM: Implement SBI v0.3 SRST extension
...
|
|
Machine generations up to z9 (released in May 2006) have been officially
out of service for several years now (z9 end of service - January 31, 2019).
No distributions build kernels supporting those old machine generations
anymore, except Debian, which seems to pick the oldest supported
generation. The team supporting Debian on s390 has been notified about
the change.
Raising minimum supported machine generation to z10 helps to reduce
maintenance cost and effectively remove code, which is not getting
enough testing coverage due to lack of older hardware and distributions
support. Besides that this unblocks some optimization opportunities and
allows to use wider instruction set in asm files for future features
implementation. Due to this change spectre mitigation and usercopy
implementations could be drastically simplified and many newer instructions
could be converted from ".insn" encoding to instruction names.
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Add copy_from/to_user_key functions, which perform storage key checking.
These functions can be used by KVM for emulating instructions that need
to be key checked.
These functions differ from their non _key counterparts in
include/linux/uaccess.h only in the additional key argument and must be
kept in sync with those.
Since the existing uaccess implementation on s390 makes use of move
instructions that support having an additional access key supplied,
we can implement raw_copy_from/to_user_key by enhancing the
existing implementation.
Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20220211182215.2730017-2-scgl@linux.ibm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
This is more or less a combination of commit 2e77a62cb3a6 ("arm64:
extable: add a dedicated uaccess handler") and commit 4b5305decc84
("x86/extable: Extend extable functionality").
To describe the problem that needs to solved let's cite the full arm64
commit message:
------
For inline assembly, we place exception fixups out-of-line in the
`.fixup` section such that these are out of the way of the fast path.
This has a few drawbacks:
* Since the fixup code is anonymous, backtraces will symbolize fixups
as offsets from the nearest prior symbol, currently
`__entry_tramp_text_end`. This is confusing, and painful to debug
without access to the relevant vmlinux.
* Since the exception handler adjusts the PC to execute the fixup, and
the fixup uses a direct branch back into the function it fixes,
backtraces of fixups miss the original function. This is confusing,
and violates requirements for RELIABLE_STACKTRACE (and therefore
LIVEPATCH).
* Inline assembly and associated fixups are generated from templates,
and we have many copies of logically identical fixups which only
differ in which specific registers are written to and which address
is branched to at the end of the fixup. This is potentially wasteful
of I-cache resources, and makes it hard to add additional logic to
fixups without significant bloat.
This patch address all three concerns for inline uaccess fixups by
adding a dedicated exception handler which updates registers in
exception context and subsequent returns back into the function which
faulted, removing the need for fixups specialized to each faulting
instruction.
Other than backtracing, there should be no functional change as a result
of this patch.
------
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Follow arm64 and riscv and move the EX_TABLE define to asm-extable.h
which is a lot less generic than the current linkage.h.
Also make sure that all files which contain EX_TABLE usages actually
include the new header file. This should make sure that the files
always compile and there won't be any random compile breakage due to
other header file dependencies.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
There are many different ways that access_ok() is defined across
architectures, but in the end, they all just compare against the
user_addr_max() value or they accept anything.
Provide one definition that works for most architectures, checking
against TASK_SIZE_MAX for user processes or skipping the check inside
of uaccess_kernel() sections.
For architectures without CONFIG_SET_FS(), this should be the fastest
check, as it comes down to a single comparison of a pointer against a
compile-time constant, while the architecture specific versions tend to
do something more complex for historic reasons or get something wrong.
Type checking for __user annotations is handled inconsistently across
architectures, but this is easily simplified as well by using an inline
function that takes a 'const void __user *' argument. A handful of
callers need an extra __user annotation for this.
Some architectures had trick to use 33-bit or 65-bit arithmetic on the
addresses to calculate the overflow, however this simpler version uses
fewer registers, which means it can produce better object code in the
end despite needing a second (statically predicted) branch.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mark Rutland <mark.rutland@arm.com> [arm64, asm-generic]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Stafford Horne <shorne@gmail.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Nine architectures are still missing __{get,put}_kernel_nofault:
alpha, ia64, microblaze, nds32, nios2, openrisc, sh, sparc32, xtensa.
Add a generic version that lets everything use the normal
copy_{from,to}_kernel_nofault() code based on these, removing the last
use of get_fs()/set_fs() from architecture-independent code.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add copy_from/to_user_key functions, which perform storage key checking.
These functions can be used by KVM for emulating instructions that need
to be key checked.
These functions differ from their non _key counterparts in
include/linux/uaccess.h only in the additional key argument and must be
kept in sync with those.
Since the existing uaccess implementation on s390 makes use of move
instructions that support having an additional access key supplied,
we can implement raw_copy_from/to_user_key by enhancing the
existing implementation.
Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20220211182215.2730017-2-scgl@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
|
|
There is a confusion with regard to the source address of
memcpy_real() and calling functions. While the declared
type for a source assumes a virtual address, in fact it
always called with physical address of the source.
This confusion led to bugs in copy_oldmem_kernel() and
copy_oldmem_user() functions, where __pa() macro applied
mistakenly to physical addresses. It does not lead to a
real issue, since virtual and physical addresses are
currently the same.
Fix both the bugs and memcpy_real() prototype by making
type of source address consistent to the function name
and the way it actually used.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Compiling with e.g MARCH=z900 results in compile errors:
arch/s390/lib/uaccess.c: In function 'copy_from_user_mvcos':
>> arch/s390/lib/uaccess.c:65:15: error: variable 'spec' has initializer but incomplete type
65 | union oac spec = {
Therefore make definition of union oac visible for all MARCHs.
Reported-by: kernel test robot <lkp@intel.com>
Cc: Nico Boehr <nrb@linux.ibm.com>
Cc: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Fixes: 012a224e1fa3 ("s390/uaccess: introduce bit field for OAC specifier")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Previously, we've used magic values to specify the OAC
(operand-access control) for mvcos.
Instead we introduce a bit field for it.
When using a bit field, we cannot use an immediate value with K
constraint anymore, since GCC older than 10 doesn't recognize
the bit field union as a compile time constant.
To make things work with older compilers,
load the OAC value through a register.
Bloat-o-meter reports a slight increase in kernel size with this change:
Total: Before=15692135, After=15693015, chg +0.01%
Signed-off-by: Nico Boehr <nrb@linux.ibm.com>
Co-developed-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Link: https://lore.kernel.org/r/20220111100003.743116-1-scgl@linux.ibm.com
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
All users of compat_alloc_user_space() and copy_in_user() have been
removed from the kernel, only a few functions in sparc remain that can be
changed to calling arch_copy_in_user() instead.
Link: https://lkml.kernel.org/r/20210727144859.4150043-7-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The s390 variant of strncpy_from_user() is slightly faster than the
generic variant, however convert to the generic variant now to follow
most if not all other architectures.
Converting to the generic variant was already considered a couple of
years ago. See commit f5c8b9601036 ("s390/uaccess: use sane length for
__strncpy_from_user()").
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
This patch converts s390 to use the generic entry infrastructure from
kernel/entry/*.
There are a few special things on s390:
- PIF_PER_TRAP is moved to TIF_PER_TRAP as the generic code doesn't
know about our PIF flags in exit_to_user_mode_loop().
- The old code had several ways to restart syscalls:
a) PIF_SYSCALL_RESTART, which was only set during execve to force a
restart after upgrading a process (usually qemu-kvm) to pgste page
table extensions.
b) PIF_SYSCALL, which is set by do_signal() to indicate that the
current syscall should be restarted. This is changed so that
do_signal() now also uses PIF_SYSCALL_RESTART. Continuing to use
PIF_SYSCALL doesn't work with the generic code, and changing it
to PIF_SYSCALL_RESTART makes PIF_SYSCALL and PIF_SYSCALL_RESTART
more unique.
- On s390 calling sys_sigreturn or sys_rt_sigreturn is implemented by
executing a svc instruction on the process stack which causes a fault.
While handling that fault the fault code sets PIF_SYSCALL to hand over
processing to the syscall code on exit to usermode.
The patch introduces PIF_SYSCALL_RET_SET, which is set if ptrace sets
a return value for a syscall. The s390x ptrace ABI uses r2 both for the
syscall number and return value, so ptrace cannot set the syscall number +
return value at the same time. The flag makes handling that a bit easier.
do_syscall() will just skip executing the syscall if PIF_SYSCALL_RET_SET
is set.
CONFIG_DEBUG_ASCE was removd in favour of the generic CONFIG_DEBUG_ENTRY.
CR1/7/13 will be checked both on kernel entry and exit to contain the
correct asces.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Verify on exit to user space that always
- the primary ASCE (cr1) is set to kernel ASCE
- the secondary ASCE (cr7) is set to user ASCE
If this is not the case: panic since something went terribly wrong.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Remove set_fs support from s390. With doing this rework address space
handling and simplify it. As a result address spaces are now setup
like this:
CPU running in | %cr1 ASCE | %cr7 ASCE | %cr13 ASCE
----------------------------|-----------|-----------|-----------
user space | user | user | kernel
kernel, normal execution | kernel | user | kernel
kernel, kvm guest execution | gmap | user | kernel
To achieve this the getcpu vdso syscall is removed in order to avoid
secondary address mode and a separate vdso address space in for user
space. The getcpu vdso syscall will be implemented differently with a
subsequent patch.
The kernel accesses user space always via secondary address space.
This happens in different ways:
- with mvcos in home space mode and directly read/write to secondary
address space
- with mvcs/mvcp in primary space mode and copy from primary space to
secondary space or vice versa
- with e.g. cs in secondary space mode and access secondary space
Switching translation modes happens with sacf before and after
instructions which access user space, like before.
Lazy handling of control register reloading is removed in the hope to
make everything simpler, but at the cost of making kernel entry and
exit a bit slower. That is: on kernel entry the primary asce is always
changed to contain the kernel asce, and on kernel exit the primary
asce is changed again so it contains the user asce.
In kernel mode there is only one exception to the primary asce: when
kvm guests are executed the primary asce contains the gmap asce (which
describes the guest address space). The primary asce is reset to
kernel asce whenever kvm guest execution is interrupted, so that this
doesn't has to be taken into account for any user space accesses.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Add default cases for __put_user_fn()/__get_user_fn(). This doesn't
fix anything since the functions are only called with sane values.
However we get rid of smatch warnings:
./arch/s390/include/asm/uaccess.h:143 __get_user_fn() error: uninitialized symbol 'rc'.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
segment_eq is only used to implement uaccess_kernel. Just open code
uaccess_kernel in the arch uaccess headers and remove one layer of
indirection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Greentime Hu <green.hu@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Link: http://lkml.kernel.org/r/20200710135706.537715-5-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
s390_kernel_write()'s function type is almost identical to memcpy().
Change its return type to "void *" so they can be used interchangeably.
Cc: linux-s390@vger.kernel.org
Cc: heiko.carstens@de.ibm.com
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Acked-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> # s390
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Depending on inlining decisions by the compiler, __get/put_user_fn
might become out of line. Then the compiler is no longer able to tell
that size can only be 1,2,4 or 8 due to the check in __get/put_user
resulting in false positives like
./arch/s390/include/asm/uaccess.h: In function ‘__put_user_fn’:
./arch/s390/include/asm/uaccess.h:113:9: warning: ‘rc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
113 | return rc;
| ^~
./arch/s390/include/asm/uaccess.h: In function ‘__get_user_fn’:
./arch/s390/include/asm/uaccess.h:143:9: warning: ‘rc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
143 | return rc;
| ^~
These functions are supposed to be always inlined. Mark it as such.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
arch/s390/lib/uaccess.c is built without kasan instrumentation. Kasan
checks are performed explicitly in copy_from_user/copy_to_user
functions. But since those functions could be inlined, calls from
files like uaccess.c with instrumentation disabled won't generate
kasan reports. This is currently the case with strncpy_from_user
function which was revealed by newly added kasan test. Avoid inlining of
copy_from_user/copy_to_user when the kernel is built with kasan support
to make sure kasan checks are fully functional.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Every in-kernel use of this function defined it to KERNEL_DS (either as
an actual define, or as an inline function). It's an entirely
historical artifact, and long long long ago used to actually read the
segment selector valueof '%ds' on x86.
Which in the kernel is always KERNEL_DS.
Inspired by a patch from Jann Horn that just did this for a very small
subset of users (the ones in fs/), along with Al who suggested a script.
I then just took it to the logical extreme and removed all the remaining
gunk.
Roughly scripted with
git grep -l '(get_ds())' -- :^tools/ | xargs sed -i 's/(get_ds())/(KERNEL_DS)/'
git grep -lw 'get_ds' -- :^tools/ | xargs sed -i '/^#define get_ds()/d'
plus manual fixups to remove a few unusual usage patterns, the couple of
inline function cases and to fix up a comment that had become stale.
The 'get_ds()' function remains in an x86 kvm selftest, since in user
space it actually does something relevant.
Inspired-by: Jann Horn <jannh@google.com>
Inspired-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The vdso code for the getcpu() and the clock_gettime() call use the access
register mode to access the per-CPU vdso data page with the current code.
An alternative to the complicated AR mode is to use the secondary space
mode. This makes the vdso faster and quite a bit simpler. The downside is
that the uaccess code has to be changed quite a bit.
Which instructions are used depends on the machine and what kind of uaccess
operation is requested. The instruction dictates which ASCE value needs
to be loaded into %cr1 and %cr7.
The different cases:
* User copy with MVCOS for z10 and newer machines
The MVCOS instruction can copy between the primary space (aka user) and
the home space (aka kernel) directly. For set_fs(KERNEL_DS) the kernel
ASCE is loaded into %cr1. For set_fs(USER_DS) the user space is already
loaded in %cr1.
* User copy with MVCP/MVCS for older machines
To be able to execute the MVCP/MVCS instructions the kernel needs to
switch to primary mode. The control register %cr1 has to be set to the
kernel ASCE and %cr7 to either the kernel ASCE or the user ASCE dependent
on set_fs(KERNEL_DS) vs set_fs(USER_DS).
* Data access in the user address space for strnlen / futex
To use "normal" instruction with data from the user address space the
secondary space mode is used. The kernel needs to switch to primary mode,
%cr1 has to contain the kernel ASCE and %cr7 either the user ASCE or the
kernel ASCE, dependent on set_fs.
To load a new value into %cr1 or %cr7 is an expensive operation, the kernel
tries to be lazy about it. E.g. for multiple user copies in a row with
MVCP/MVCS the replacement of the vdso ASCE in %cr7 with the user ASCE is
done only once. On return to user space a CPU bit is checked that loads the
vdso ASCE again.
To enable and disable the data access via the secondary space two new
functions are added, enable_sacf_uaccess and disable_sacf_uaccess. The fact
that a context is in secondary space uaccess mode is stored in the
mm_segment_t value for the task. The code of an interrupt may use set_fs
as long as it returns to the previous state it got with get_fs with another
call to set_fs. The code in finish_arch_post_lock_switch simply has to do a
set_fs with the current mm_segment_t value for the task.
For CPUs with MVCOS:
CPU running in | %cr1 ASCE | %cr7 ASCE |
--------------------------------------|-----------|-----------|
user space | user | vdso |
kernel, USER_DS, normal-mode | user | vdso |
kernel, USER_DS, normal-mode, lazy | user | user |
kernel, USER_DS, sacf-mode | kernel | user |
kernel, KERNEL_DS, normal-mode | kernel | vdso |
kernel, KERNEL_DS, normal-mode, lazy | kernel | kernel |
kernel, KERNEL_DS, sacf-mode | kernel | kernel |
For CPUs without MVCOS:
CPU running in | %cr1 ASCE | %cr7 ASCE |
--------------------------------------|-----------|-----------|
user space | user | vdso |
kernel, USER_DS, normal-mode | user | vdso |
kernel, USER_DS, normal-mode lazy | kernel | user |
kernel, USER_DS, sacf-mode | kernel | user |
kernel, KERNEL_DS, normal-mode | kernel | vdso |
kernel, KERNEL_DS, normal-mode, lazy | kernel | kernel |
kernel, KERNEL_DS, sacf-mode | kernel | kernel |
The lines with "lazy" refer to the state after a copy via the secondary
space with a delayed reload of %cr1 and %cr7.
There are three hardware address spaces that can cause a DAT exception,
primary, secondary and home space. The exception can be related to
four different fault types: user space fault, vdso fault, kernel fault,
and the gmap faults.
Dependent on the set_fs state and normal vs. sacf mode there are a number
of fault combinations:
1) user address space fault via the primary ASCE
2) gmap address space fault via the primary ASCE
3) kernel address space fault via the primary ASCE for machines with
MVCOS and set_fs(KERNEL_DS)
4) vdso address space faults via the secondary ASCE with an invalid
address while running in secondary space in problem state
5) user address space fault via the secondary ASCE for user-copy
based on the secondary space mode, e.g. futex_ops or strnlen_user
6) kernel address space fault via the secondary ASCE for user-copy
with secondary space mode with set_fs(KERNEL_DS)
7) kernel address space fault via the primary ASCE for user-copy
with secondary space mode with set_fs(USER_DS) on machines without
MVCOS.
8) kernel address space fault via the home space ASCE
Replace user_space_fault() with a new function get_fault_type() that
can distinguish all four different fault types.
With these changes the futex atomic ops from the kernel and the
strnlen_user will get a little bit slower, as well as the old style
uaccess with MVCP/MVCS. All user accesses based on MVCOS will be as
fast as before. On the positive side, the user space vdso code is a
lot faster and Linux ceases to use the complicated AR mode.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull uacess-unaligned removal from Al Viro:
"That stuff had just one user, and an exotic one, at that - binfmt_flat
on arm and m68k"
* 'work.uaccess-unaligned' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
kill {__,}{get,put}_user_unaligned()
binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail
|
|
no users left
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
no callers, no consistent semantics, no sane way to use it...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull uaccess unification updates from Al Viro:
"This is the uaccess unification pile. It's _not_ the end of uaccess
work, but the next batch of that will go into the next cycle. This one
mostly takes copy_from_user() and friends out of arch/* and gets the
zero-padding behaviour in sync for all architectures.
Dealing with the nocache/writethrough mess is for the next cycle;
fortunately, that's x86-only. Same for cleanups in iov_iter.c (I am
sold on access_ok() in there, BTW; just not in this pile), same for
reducing __copy_... callsites, strn*... stuff, etc. - there will be a
pile about as large as this one in the next merge window.
This one sat in -next for weeks. -3KLoC"
* 'work.uaccess' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (96 commits)
HAVE_ARCH_HARDENED_USERCOPY is unconditional now
CONFIG_ARCH_HAS_RAW_COPY_USER is unconditional now
m32r: switch to RAW_COPY_USER
hexagon: switch to RAW_COPY_USER
microblaze: switch to RAW_COPY_USER
get rid of padding, switch to RAW_COPY_USER
ia64: get rid of copy_in_user()
ia64: sanitize __access_ok()
ia64: get rid of 'segment' argument of __do_{get,put}_user()
ia64: get rid of 'segment' argument of __{get,put}_user_check()
ia64: add extable.h
powerpc: get rid of zeroing, switch to RAW_COPY_USER
esas2r: don't open-code memdup_user()
alpha: fix stack smashing in old_adjtimex(2)
don't open-code kernel_setsockopt()
mips: switch to RAW_COPY_USER
mips: get rid of tail-zeroing in primitives
mips: make copy_from_user() zero tail explicitly
mips: clean and reorder the forest of macros...
mips: consolidate __invoke_... wrappers
...
|
|
[folded a fix from Martin]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Commit fd2d2b191fe7 ("s390: get_user() should zero on failure")
intended to fix s390's get_user() implementation which did not zero
the target operand if the read from user space faulted. Unfortunately
the patch has no effect: the corresponding inline assembly specifies
that the operand is only written to ("=") and the previous value is
discarded.
Therefore the compiler is free to and actually does omit the zero
initialization.
To fix this simply change the contraint modifier to "+", so the
compiler cannot omit the initialization anymore.
Fixes: c9ca78415ac1 ("s390/uaccess: provide inline variants of get_user/put_user")
Fixes: fd2d2b191fe7 ("s390: get_user() should zero on failure")
Cc: stable@vger.kernel.org
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
