| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This is needed in e.g. ARM vGIC emulation, where the MMIO handling
depends on the VCPU that does the access.
Signed-off-by: Nikolay Nikolaev <n.nikolaev@virtualopensystems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
This patch introduces a new module parameter for the KVM module; when it
is present, KVM attempts a bit of polling on every HLT before scheduling
itself out via kvm_vcpu_block.
This parameter helps a lot for latency-bound workloads---in particular
I tested it with O_DSYNC writes with a battery-backed disk in the host.
In this case, writes are fast (because the data doesn't have to go all
the way to the platters) but they cannot be merged by either the host or
the guest. KVM's performance here is usually around 30% of bare metal,
or 50% if you use cache=directsync or cache=writethrough (these
parameters avoid that the guest sends pointless flush requests, and
at the same time they are not slow because of the battery-backed cache).
The bad performance happens because on every halt the host CPU decides
to halt itself too. When the interrupt comes, the vCPU thread is then
migrated to a new physical CPU, and in general the latency is horrible
because the vCPU thread has to be scheduled back in.
With this patch performance reaches 60-65% of bare metal and, more
important, 99% of what you get if you use idle=poll in the guest. This
means that the tunable gets rid of this particular bottleneck, and more
work can be done to improve performance in the kernel or QEMU.
Of course there is some price to pay; every time an otherwise idle vCPUs
is interrupted by an interrupt, it will poll unnecessarily and thus
impose a little load on the host. The above results were obtained with
a mostly random value of the parameter (500000), and the load was around
1.5-2.5% CPU usage on one of the host's core for each idle guest vCPU.
The patch also adds a new stat, /sys/kernel/debug/kvm/halt_successful_poll,
that can be used to tune the parameter. It counts how many HLT
instructions received an interrupt during the polling period; each
successful poll avoids that Linux schedules the VCPU thread out and back
in, and may also avoid a likely trip to C1 and back for the physical CPU.
While the VM is idle, a Linux 4 VCPU VM halts around 10 times per second.
Of these halts, almost all are failed polls. During the benchmark,
instead, basically all halts end within the polling period, except a more
or less constant stream of 50 per second coming from vCPUs that are not
running the benchmark. The wasted time is thus very low. Things may
be slightly different for Windows VMs, which have a ~10 ms timer tick.
The effect is also visible on Marcelo's recently-introduced latency
test for the TSC deadline timer. Though of course a non-RT kernel has
awful latency bounds, the latency of the timer is around 8000-10000 clock
cycles compared to 20000-120000 without setting halt_poll_ns. For the TSC
deadline timer, thus, the effect is both a smaller average latency and
a smaller variance.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch adds PML support in VMX. A new module parameter 'enable_pml' is added
to allow user to enable/disable it manually.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch adds new kvm_x86_ops dirty logging hooks to enable/disable dirty
logging for particular memory slot, and to flush potentially logged dirty GPAs
before reporting slot->dirty_bitmap to userspace.
kvm x86 common code calls these hooks when they are available so PML logic can
be hidden to VMX specific. SVM won't be impacted as these hooks remain NULL
there.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch changes the second parameter of kvm_mmu_slot_remove_write_access from
'slot id' to 'struct kvm_memory_slot *' to align with kvm_x86_ops dirty logging
hooks, which will be introduced in further patch.
Better way is to change second parameter of kvm_arch_commit_memory_region from
'struct kvm_userspace_memory_region *' to 'struct kvm_memory_slot * new', but it
requires changes on other non-x86 ARCH too, so avoid it now.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
If we got a wraparound of 32-bit operand, and the limit is 0xffffffff, read and
writes should be successful. It just needs to be done in two segments.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The IRET instruction should clear NMI masking, but the current implementation
does not do so.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-next
KVM: s390: fixes and features for kvm/next (3.20)
1. Generic
- sparse warning (make function static)
- optimize locking
- bugfixes for interrupt injection
- fix MVPG addressing modes
2. hrtimer/wakeup fun
A recent change can cause KVM hangs if adjtime is used in the host.
The hrtimer might wake up too early or too late. Too early is fatal
as vcpu_block will see that the wakeup condition is not met and
sleep again. This CPU might never wake up again.
This series addresses this problem. adjclock slowing down the host
clock will result in too late wakeups. This will require more work.
In addition to that we also change the hrtimer from REALTIME to
MONOTONIC to avoid similar problems with timedatectl set-time.
3. sigp rework
We will move all "slow" sigps to QEMU (protected with a capability that
can be enabled) to avoid several races between concurrent SIGP orders.
4. Optimize the shadow page table
Provide an interface to announce the maximum guest size. The kernel
will use that to make the pagetable 2,3,4 (or theoretically) 5 levels.
5. Provide an interface to set the guest TOD
We now use two vm attributes instead of two oneregs, as oneregs are
vcpu ioctl and we don't want to call them from other threads.
6. Protected key functions
The real HMC allows to enable/disable protected key CPACF functions.
Lets provide an implementation + an interface for QEMU to activate
this the protected key instructions.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-next
KVM/ARM changes for v3.20 including GICv3 emulation, dirty page logging, added
trace symbols, and adding an explicit VGIC init device control IOCTL.
Conflicts:
arch/arm64/include/asm/kvm_arm.h
arch/arm64/kvm/handle_exit.c
|
|
The return value of kvm_arch_vcpu_postcreate is not checked in its
caller. This is okay, because only x86 provides vcpu_postcreate right
now and it could only fail if vcpu_load failed. But that is not
possible during KVM_CREATE_VCPU (kvm_arch_vcpu_load is void, too), so
just get rid of the unchecked return value.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
SuSE's 2.6.16 kernel fails to boot if the delta between tsc_timestamp
and rdtsc is larger than a given threshold:
* If we get more than the below threshold into the future, we rerequest
* the real time from the host again which has only little offset then
* that we need to adjust using the TSC.
*
* For now that threshold is 1/5th of a jiffie. That should be good
* enough accuracy for completely broken systems, but also give us swing
* to not call out to the host all the time.
*/
#define PVCLOCK_DELTA_MAX ((1000000000ULL / HZ) / 5)
Disable masterclock support (which increases said delta) in case the
boot vcpu does not use MSR_KVM_SYSTEM_TIME_NEW.
Upstreams kernels which support pvclock vsyscalls (and therefore make
use of PVCLOCK_STABLE_BIT) use MSR_KVM_SYSTEM_TIME_NEW.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
arch/x86/kvm/x86.c:495:5: sparse: symbol 'kvm_read_nested_guest_page' was not declared. Should it be static?
arch/x86/kvm/x86.c:646:5: sparse: symbol '__kvm_set_xcr' was not declared. Should it be static?
arch/x86/kvm/x86.c:1183:15: sparse: symbol 'max_tsc_khz' was not declared. Should it be static?
arch/x86/kvm/x86.c:1237:6: sparse: symbol 'kvm_track_tsc_matching' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
We now have a generic function that does most of the work of
kvm_vm_ioctl_get_dirty_log, now use it.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
|
|
Emulation does not utilize the feature.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Adds a function kvm_vcpu_set_pending_timer instead of calling
kvm_make_request in lapic.c.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
For the hrtimer which emulates the tscdeadline timer in the guest,
add an option to advance expiration, and busy spin on VM-entry waiting
for the actual expiration time to elapse.
This allows achieving low latencies in cyclictest (or any scenario
which requires strict timing regarding timer expiration).
Reduces average cyclictest latency from 12us to 8us
on Core i5 desktop.
Note: this option requires tuning to find the appropriate value
for a particular hardware/guest combination. One method is to measure the
average delay between apic_timer_fn and VM-entry.
Another method is to start with 1000ns, and increase the value
in say 500ns increments until avg cyclictest numbers stop decreasing.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Several hypervisors need MSR auto load/restore feature.
We read MSRs from VM-entry MSR load area which specified by L1,
and load them via kvm_set_msr in the nested entry.
When nested exit occurs, we get MSRs via kvm_get_msr, writing
them to L1`s MSR store area. After this, we read MSRs from VM-exit
MSR load area, and load them via kvm_set_msr.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Userspace is expecting non-compacted format for KVM_GET_XSAVE, but
struct xsave_struct might be using the compacted format. Convert
in order to preserve userspace ABI.
Likewise, userspace is passing non-compacted format for KVM_SET_XSAVE
but the kernel will pass it to XRSTORS, and we need to convert back.
Fixes: f31a9f7c71691569359fa7fb8b0acaa44bce0324
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: stable@vger.kernel.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Tested-by: Nadav Amit <namit@cs.technion.ac.il>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
cs.base is declared as a __u64 variable and vector is a u32 so this
causes a static checker warning. The user indeed can set "sipi_vector"
to any u32 value in kvm_vcpu_ioctl_x86_set_vcpu_events(), but the
value should really have 8-bit precision only.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Create a new header, and hide the device assignment functions there.
Move struct kvm_assigned_dev_kernel to assigned-dev.c by modifying
arch/x86/kvm/iommu.c to take a PCI device struct.
Based on a patch by Radim Krcmar <rkrcmark@redhat.com>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Now that ia64 is gone, we can hide deprecated device assignment in x86.
Notable changes:
- kvm_vm_ioctl_assigned_device() was moved to x86/kvm_arch_vm_ioctl()
The easy parts were removed from generic kvm code, remaining
- kvm_iommu_(un)map_pages() would require new code to be moved
- struct kvm_assigned_dev_kernel depends on struct kvm_irq_ack_notifier
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
ia64 does not need them anymore. Ack notifiers become x86-specific
too.
Suggested-by: Gleb Natapov <gleb@kernel.org>
Reviewed-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When running the tsc_adjust kvm-unit-test on an AMD processor with the
IA32_TSC_ADJUST feature enabled, the WARN_ON in svm_adjust_tsc_offset can be
triggered. This WARN_ON checks for a negative adjustment in case __scale_tsc
is called; however it may trigger unnecessary warnings.
This patch moves the WARN_ON to trigger only if __scale_tsc will actually be
called from svm_adjust_tsc_offset. In addition make adj in kvm_set_msr_common
s64 since this can have signed values.
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
PCIDs are only supported in 64-bit mode. No need to clear bit 63
of CR3 unless the host is 64-bit.
Reported by Fengguang Wu's autobuilder.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The new trace event records:
* the id of vcpu being updated
* the pvclock_vcpu_time_info struct being written to guest memory
This is useful for debugging pvclock bugs, such as the bug fixed by
"[PATCH] kvm: x86: Fix kvm clock versioning.".
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm updates the version number for the guest paravirt clock structure by
incrementing the version of its private copy. It does not read the guest
version, so will write version = 2 in the first update for every new VM,
including after restoring a saved state. If guest state is saved during
reading the clock, it could read and accept struct fields and guest TSC
from two different updates. This changes the code to increment the guest
version and write it back.
Signed-off-by: Owen Hofmann <osh@google.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When the guest writes to the TSC, the masterclock TSC copy must be
updated as well along with the TSC_OFFSET update, otherwise a negative
tsc_timestamp is calculated at kvm_guest_time_update.
Once "if (!vcpus_matched && ka->use_master_clock)" is simplified to
"if (ka->use_master_clock)", the corresponding "if (!ka->use_master_clock)"
becomes redundant, so remove the do_request boolean and collapse
everything into a single condition.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
If the emulation ends in fault, eflags should not be updated. However, several
instruction emulations (actually all the fastops) currently update eflags, if
the fault was detected afterwards (e.g., #PF during writeback).
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Although Intel SDM mentions bit 63 is reserved, MOV to CR3 can have bit 63 set.
As Intel SDM states in section 4.10.4 "Invalidation of TLBs and
Paging-Structure Caches": " MOV to CR3. ... If CR4.PCIDE = 1 and bit 63 of the
instruction’s source operand is 0 ..."
In other words, bit 63 is not reserved. KVM emulator currently consider bit 63
as reserved. Fix it.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
x86 debug registers hold a linear address. Therefore, breakpoints detection
should consider CS.base, and check whether instruction linear address equals
(CS.base + RIP). This patch introduces a function to evaluate RIP linear
address and uses it for breakpoints detection.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Real-mode exceptions do not deliver error code. As can be seen in Intel SDM
volume 2, real-mode exceptions do not have parentheses, which indicate
error-code. To avoid significant changes of the code, the error code is
"removed" during exception queueing.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Expose Intel AVX-512 feature bits to guest. Also add checks for
xcr0 AVX512 related bits according to spec:
http://download-software.intel.com/sites/default/files/managed/71/2e/319433-017.pdf
Signed-off-by: Chao Peng <chao.p.peng@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
If DR4/5 is accessed when it is unavailable (since CR4.DE is set), then #UD
should be generated even if CPL>0. This is according to Intel SDM Table 6-2:
"Priority Among Simultaneous Exceptions and Interrupts".
Note, that this may happen on the first DR access, even if the host does not
sets debug breakpoints. Obviously, it occurs when the host debugs the guest.
This patch moves the DR4/5 checks from __kvm_set_dr/_kvm_get_dr to handle_dr.
The emulator already checks DR4/5 availability in check_dr_read. Nested
virutalization related calls to kvm_set_dr/kvm_get_dr would not like to inject
exceptions to the guest.
As for SVM, the patch follows the previous logic as much as possible. Anyhow,
it appears the DR interception code might be buggy - even if the DR access
may cause an exception, the instruction is skipped.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Intel SDM 17.2.4 (Debug Control Register (DR7)) says: "The processor clears the
GD flag upon entering to the debug exception handler." This sentence may be
misunderstood as if it happens only on #DB due to debug-register protection,
but it happens regardless to the cause of the #DB.
Fix the behavior to match both real hardware and Bochs.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The previous patch blocked invalid writes directly when the MSR
is written. As a precaution, prevent future similar mistakes by
gracefulling handle GPs caused by writes to shared MSRs.
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Honig <ahonig@google.com>
[Remove parts obsoleted by Nadav's patch. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Upon WRMSR, the CPU should inject #GP if a non-canonical value (address) is
written to certain MSRs. The behavior is "almost" identical for AMD and Intel
(ignoring MSRs that are not implemented in either architecture since they would
anyhow #GP). However, IA32_SYSENTER_ESP and IA32_SYSENTER_EIP cause #GP if
non-canonical address is written on Intel but not on AMD (which ignores the top
32-bits).
Accordingly, this patch injects a #GP on the MSRs which behave identically on
Intel and AMD. To eliminate the differences between the architecutres, the
value which is written to IA32_SYSENTER_ESP and IA32_SYSENTER_EIP is turned to
canonical value before writing instead of injecting a #GP.
Some references from Intel and AMD manuals:
According to Intel SDM description of WRMSR instruction #GP is expected on
WRMSR "If the source register contains a non-canonical address and ECX
specifies one of the following MSRs: IA32_DS_AREA, IA32_FS_BASE, IA32_GS_BASE,
IA32_KERNEL_GS_BASE, IA32_LSTAR, IA32_SYSENTER_EIP, IA32_SYSENTER_ESP."
According to AMD manual instruction manual:
LSTAR/CSTAR (SYSCALL): "The WRMSR instruction loads the target RIP into the
LSTAR and CSTAR registers. If an RIP written by WRMSR is not in canonical
form, a general-protection exception (#GP) occurs."
IA32_GS_BASE and IA32_FS_BASE (WRFSBASE/WRGSBASE): "The address written to the
base field must be in canonical form or a #GP fault will occur."
IA32_KERNEL_GS_BASE (SWAPGS): "The address stored in the KernelGSbase MSR must
be in canonical form."
This patch fixes CVE-2014-3610.
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
|
|
This fixes the following OOPS:
loaded kvm module (v3.17-rc1-168-gcec26bc)
BUG: unable to handle kernel paging request at fffffffffffffffe
IP: [<ffffffff81168449>] put_page+0x9/0x30
PGD 1e15067 PUD 1e17067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
[<ffffffffa063271d>] ? kvm_vcpu_reload_apic_access_page+0x5d/0x70 [kvm]
[<ffffffffa013b6db>] vmx_vcpu_reset+0x21b/0x470 [kvm_intel]
[<ffffffffa0658816>] ? kvm_pmu_reset+0x76/0xb0 [kvm]
[<ffffffffa064032a>] kvm_vcpu_reset+0x15a/0x1b0 [kvm]
[<ffffffffa06403ac>] kvm_arch_vcpu_setup+0x2c/0x50 [kvm]
[<ffffffffa062e540>] kvm_vm_ioctl+0x200/0x780 [kvm]
[<ffffffff81212170>] do_vfs_ioctl+0x2d0/0x4b0
[<ffffffff8108bd99>] ? __mmdrop+0x69/0xb0
[<ffffffff812123d1>] SyS_ioctl+0x81/0xa0
[<ffffffff8112a6f6>] ? __audit_syscall_exit+0x1f6/0x2a0
[<ffffffff817229e9>] system_call_fastpath+0x16/0x1b
Code: c6 78 ce a3 81 4c 89 e7 e8 d9 80 ff ff 0f 0b 4c 89 e7 e8 8f f6 ff ff e9 fa fe ff ff 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90 <48> f7 07 00 c0 00 00 55 48 89 e5 75 1e 8b 47 1c 85 c0 74 27 f0
RIP [<ffffffff81193045>] put_page+0x5/0x50
when not using the in-kernel irqchip ("-machine kernel_irqchip=off"
with QEMU). The fix is to make the same check in
kvm_vcpu_reload_apic_access_page that we already have
in vmx.c's vm_need_virtualize_apic_accesses().
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Fixes: 4256f43f9fab91e1c17b5846a240cf4b66a768a8
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In order to make the APIC access page migratable, stop pinning it in
memory.
And because the APIC access page is not pinned in memory, we can
remove kvm_arch->apic_access_page. When we need to write its
physical address into vmcs, we use gfn_to_page() to get its page
struct, which is needed to call page_to_phys(); the page is then
immediately unpinned.
Suggested-by: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Currently, the APIC access page is pinned by KVM for the entire life
of the guest. We want to make it migratable in order to make memory
hot-unplug available for machines that run KVM.
This patch prepares to handle this in generic code, through a new
request bit (that will be set by the MMU notifier) and a new hook
that is called whenever the request bit is processed.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This will be used to let the guest run while the APIC access page is
not pinned. Because subsequent patches will fill in the function
for x86, place the (still empty) x86 implementation in the x86.c file
instead of adding an inline function in kvm_host.h.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Avoid open coded calculations for bank MSRs by using well-defined
macros that hide the index of higher bank MSRs.
No semantic changes.
Signed-off-by: Chen Yucong <slaoub@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Guest which sets the PAT CR to invalid value should get a #GP. Currently, if
vmx supports loading PAT CR during entry, then the value is not checked. This
patch makes the required check in that case.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
A one-line wrapper around kvm_make_request is not particularly
useful. Replace kvm_mmu_flush_tlb() with kvm_make_request().
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
- we count KVM_REQ_TLB_FLUSH requests, not actual flushes
(KVM can have multiple requests for one flush)
- flushes from kvm_flush_remote_tlbs aren't counted
- it's easy to make a direct request by mistake
Solve these by postponing the counting to kvm_check_request().
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commit fc3a9157d314 ("KVM: X86: Don't report L2 emulation failures to
user-space") disabled the reporting of L2 (nested guest) emulation failures to
userspace due to race-condition between a vmexit and the instruction emulator.
The same rational applies also to userspace applications that are permitted by
the guest OS to access MMIO area or perform PIO.
This patch extends the current behavior - of injecting a #UD instead of
reporting it to userspace - also for guest userspace code.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm_arch->ept_identity_pagetable holds the ept identity pagetable page. But
it is never used to refer to the page at all.
In vcpu initialization, it indicates two things:
1. indicates if ept page is allocated
2. indicates if a memory slot for identity page is initialized
Actually, kvm_arch->ept_identity_pagetable_done is enough to tell if the ept
identity pagetable is initialized. So we can remove ept_identity_pagetable.
NOTE: In the original code, ept identity pagetable page is pinned in memroy.
As a result, it cannot be migrated/hot-removed. After this patch, since
kvm_arch->ept_identity_pagetable is removed, ept identity pagetable page
is no longer pinned in memory. And it can be migrated/hot-removed.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch replace the set_bit method by kvm_make_request
to make code more readable and consistent.
Signed-off-by: Guo Hui Liu <liuguohui@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Currently, if a permission error happens during the translation of
the final GPA to HPA, walk_addr_generic returns 0 but does not fill
in walker->fault. To avoid this, add an x86_exception* argument
to the translate_gpa function, and let it fill in walker->fault.
The nested_page_fault field will be true, since the walk_mmu is the
nested_mmu and translate_gpu instead operates on the "outer" (NPT)
instance.
Reported-by: Valentine Sinitsyn <valentine.sinitsyn@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
If a nested page fault happens during emulation, we will inject a vmexit,
not a page fault. However because writeback happens after the injection,
we will write ctxt->eip from L2 into the L1 EIP. We do not write back
if an instruction caused an interception vmexit---do the same for page
faults.
Suggested-by: Gleb Natapov <gleb@kernel.org>
Reviewed-by: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
