| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In paravirtualized x86_64 kernels, vmalloc_fault may cause an oops
when lazy MMU updates are enabled, because set_pgd effects are being
deferred.
One instance of this problem is during process mm cleanup with memory
cgroups enabled. The chain of events is as follows:
- zap_pte_range enables lazy MMU updates
- zap_pte_range eventually calls mem_cgroup_charge_statistics,
which accesses the vmalloc'd mem_cgroup per-cpu stat area
- vmalloc_fault is triggered which tries to sync the corresponding
PGD entry with set_pgd, but the update is deferred
- vmalloc_fault oopses due to a mismatch in the PUD entries
The OOPs usually looks as so:
------------[ cut here ]------------
kernel BUG at arch/x86/mm/fault.c:396!
invalid opcode: 0000 [#1] SMP
.. snip ..
CPU 1
Pid: 10866, comm: httpd Not tainted 3.6.10-4.fc18.x86_64 #1
RIP: e030:[<ffffffff816271bf>] [<ffffffff816271bf>] vmalloc_fault+0x11f/0x208
.. snip ..
Call Trace:
[<ffffffff81627759>] do_page_fault+0x399/0x4b0
[<ffffffff81004f4c>] ? xen_mc_extend_args+0xec/0x110
[<ffffffff81624065>] page_fault+0x25/0x30
[<ffffffff81184d03>] ? mem_cgroup_charge_statistics.isra.13+0x13/0x50
[<ffffffff81186f78>] __mem_cgroup_uncharge_common+0xd8/0x350
[<ffffffff8118aac7>] mem_cgroup_uncharge_page+0x57/0x60
[<ffffffff8115fbc0>] page_remove_rmap+0xe0/0x150
[<ffffffff8115311a>] ? vm_normal_page+0x1a/0x80
[<ffffffff81153e61>] unmap_single_vma+0x531/0x870
[<ffffffff81154962>] unmap_vmas+0x52/0xa0
[<ffffffff81007442>] ? pte_mfn_to_pfn+0x72/0x100
[<ffffffff8115c8f8>] exit_mmap+0x98/0x170
[<ffffffff810050d9>] ? __raw_callee_save_xen_pmd_val+0x11/0x1e
[<ffffffff81059ce3>] mmput+0x83/0xf0
[<ffffffff810624c4>] exit_mm+0x104/0x130
[<ffffffff8106264a>] do_exit+0x15a/0x8c0
[<ffffffff810630ff>] do_group_exit+0x3f/0xa0
[<ffffffff81063177>] sys_exit_group+0x17/0x20
[<ffffffff8162bae9>] system_call_fastpath+0x16/0x1b
Calling arch_flush_lazy_mmu_mode immediately after set_pgd makes the
changes visible to the consistency checks.
Cc: <stable@vger.kernel.org>
RedHat-Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=914737
Tested-by: Josh Boyer <jwboyer@redhat.com>
Reported-and-Tested-by: Krishna Raman <kraman@redhat.com>
Signed-off-by: Samu Kallio <samu.kallio@aberdeencloud.com>
Link: http://lkml.kernel.org/r/1364045796-10720-1-git-send-email-konrad.wilk@oracle.com
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
This patch fix the regression introduced by the commit 3202bf0157ccb
"arm: mvebu: Improve the SMP support of the interrupt controller":
GPIO IRQ were no longer delivered to the CPUs.
To be delivered to a CPU an interrupt must be enabled at CPU level and
at interrupt source level. Before the offending patch, all the
interrupts were enabled at source level during map() function. Mask()
and unmask() was done by handling the per-CPU part. It was fine when
running in UP with only one CPU.
The offending patch added support for SMP, in this case mask() and
unmask() was done by handling the interrupt source level part. The
per-CPU level part was handled by the affinity API to select the CPU
which will receive the interrupt. (Due to some hardware limitation
only one CPU at a time can received a given interrupt).
For "normal" interrupt __setup_irq() was called when an irq was
registered. irq_set_affinity() is called from this function, which
enabled the interrupt on one of the CPUs. Whereas for GPIO IRQ which
were chained interrupts, the irq_set_affinity() was never called and
none of the CPUs was selected to receive the interrupt.
With this patch all the interrupt are enable on the current CPU during
map() function. Enabling the interrupts on a CPU doesn't depend
anymore on irq_set_affinity() and then the chained irq are not anymore
a special case. However the CPU which will receive the irq can still
be modify later using irq_set_affinity().
Tested with Mirabox (A370) and Openblocks AX3 (AXP), rootfs mounted
over NFS, compiled with CONFIG_SMP=y/N.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reported-by: Ryan Press <ryan@presslab.us>
Investigated-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ryan Press <ryan@presslab.us>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
We can't compile a kernel with CONFIG_ALTIVEC=n when
CONFIG_PPC_TRANSACTIONAL_MEM=y. We currently get:
arch/powerpc/kernel/tm.S:320: Error: unsupported relocation against THREAD_VSCR
arch/powerpc/kernel/tm.S:323: Error: unsupported relocation against THREAD_VR0
arch/powerpc/kernel/tm.S:323: Error: unsupported relocation against THREAD_VR0
etc.
The below fixes this with a sprinkling of #ifdefs.
This was found by mpe with kisskb:
http://kisskb.ellerman.id.au/kisskb/buildresult/8539442/
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
arch_local_irq_save() and friends are required to act as compiler
memory barriers. This patch adds a "memory" clobber to the inline
asm code in arch_local_irq_restore() which is used as the building
block for other functions needing to set/clear the interrupt enable
in the CSR register.
Signed-off-by: Mark Salter <msalter@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A nasty bug in fs/namespace.c caught by Andrey + a couple of less
serious unpleasantness - ecryptfs misc device playing hopeless games
with try_module_get() and palinfo procfs support being... not quite
correctly done, to be polite."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
mnt: release locks on error path in do_loopback
palinfo fixes
procfs: add proc_remove_subtree()
ecryptfs: close rmmod race
|
|
* check for proc_mkdir() failures
* fix buffer overrun - sizeof(format string) is *not* enough to
hold sprintf() result.
* use proc_remove_subtree(); life's much easier with it
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The arch_local_irq_save(), etc., routines are required to function
as compiler barriers. They do, but it's subtle and requires knowing
that the gcc builtin __insn_mtspr() is marked as a memory clobber.
Provide a comment explaining the assumption.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
[ This came about from me wondering about the synchronization rules of
__insn_mtspr() - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim <kgene.kim@samsung.com>:
samsung fixes can support s3c24xx for v3.9
* tag 'samsung-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C24XX: Fix interrupt pending register offset of the EINT controller
ARM: S3C24XX: Correct NR_IRQS definition for s3c2440
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The external pending interrupt register address (EINTPEND) offset is
0xa8, not 0x08. Without this patch the external interrupts are not
properly acknowledged, which may lead to an interrupt storm and the
system hang as soon as any external interrupt is requested.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Due to NR_IRQS being incorrectly defined not all IRQ domains can
be registered for S3C2440. It causes following errors on a s3c2440
SoC based board:
NR_IRQS:89
S3C2440: IRQ Support
irq: clearing pending status 00000002
------------[ cut here ]------------
WARNING: at kernel/irq/irqdomain.c:234 0xc0056ed0()
...
irq: could not create irq-domain
...
s3c2410-wdt s3c2410-wdt: failed to install irq (-22)
s3c2410-wdt: probe of s3c2410-wdt failed with error -22
...
samsung-uart s3c2440-uart.0: cannot get irq 74
Fix this by increasing NR_IRQS to at least (IRQ_S3C2443_AC97 + 1)
if CPU_S3C2440 is selected, so the subintc IRQ domain gets properly
registered.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The imx fixes for 3.9, take 5:
* A couple imx35 clock fixes for regressions caused by common clock
framework conversion. The admux and iomux get disabled by common
clock framework late initcall, and hence causes problems.
* Add missing twd clock lookup in device tree. This becomes required
since commit bd60345 (ARM: use device tree to get smp_twd clock)
forces all DT boot to find lookup from device tree.
* Fix imx6q ldb_di clock parents mismatch per reference manual.
* tag 'imx-fixes-3.9-5' of git://git.linaro.org/people/shawnguo/linux-2.6: (217 commits)
ARM i.MX6: Fix ldb_di clock selection
ARM: imx: provide twd clock lookup from device tree
ARM: imx35 Bugfix admux clock
ARM: clk-imx35: Bugfix iomux clock
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
According to the recent i.MX6 Quad technical reference manual, mode 0x4 (100b)
of the CCM_CS2DCR register (address 0x020C402C) bits [11-9] and [14-12] select
the PLL3 clock, and not the PLL3 PFD1 540M clock. In our code, the PLL3 root
clock is named 'pll3_usb_otg', select this instead of the 540M clock.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
While booting from device tree, imx6q used to provide twd clock lookup
by calling clk_register_clkdev() in clock driver. However, the commit
bd60345 (ARM: use device tree to get smp_twd clock) forces DT boot to
look up the clock from device tree. It causes the failure below when
twd driver tries to get the clock, and hence kernel has to calibrate the
local timer frequency.
smp_twd: clock not found -2
...
Calibrating local timer... 396.13MHz.
Fix the regression by providing twd clock lookup from device tree, and
remove the unused twd clk_register_clkdev() call from clock driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The admux clock seems to be the audmux clock as tests show. audmux does
not work without this clock enabled. Currently imx35 does not register a
clock device for audmux. This patch adds this registration. imx-audmux
driver already handles a clock device, so no changes are necessary
there.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch enables iomuxc_gate clock. It is necessary to be able to
reconfigure iomux pads. Without this clock enabled, the
clk_disable_unused function will disable this clock and the iomux pads
are not configurable anymore. This happens at every boot. After a reboot
(watchdog system reset) the clock is not enabled again, so all iomux pad
reconfigurations in boot code are without effect.
The iomux pads should be always configurable, so this patch always
enables it.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Let's not burden ia64 with checks in the common efivars code that we're not
writing too much data to the variable store. That kind of thing is an x86
firmware bug, plain and simple.
efi_query_variable_store() provides platforms with a wrapper in which they can
perform checks and workarounds for EFI variable storage bugs.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
Compiling for linux-3.9-rc1 and later fails with:
drivers/gpio/devres.c: In function 'devm_gpio_request_one':
drivers/gpio/devres.c:90:2: error: implicit declaration of function 'gpio_request_one' [-Werror=implicit-function-declaration]
So provide a local gpio_request_one() function. Code largely borrowed from
blackfin's local gpio_request_one() function.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes
Pull powerpc bugfix from Stephen Rothwell:
"A single BUG_ON fix for a condition that could happen for machines
with certain hardware installed."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes:
powerpc: pSeries_lpar_hpte_remove fails from Adjunct partition being performed before the ANDCOND test
|
|
ARC irqsave/restore macros were missing the compiler barrier, causing a
stale load in irq-enabled region be used in irq-safe region, despite
being changed, because the register holding the value was still live.
The problem manifested as random crashes in timer code when stress
testing ARCLinux (3.9-rc3) on a !SMP && !PREEMPT_COUNT
Here's the exact sequence which caused this:
(0). tv1[x] <----> t1 <---> t2
(1). mod_timer(t1) interrupted after it calls timer_pending()
(2). mod_timer(t2) completes
(3). mod_timer(t1) resumes but messes up the list
(4). __runt_timers( ) uses bogus timer_list entry / crashes in
timer->function
Essentially mod_timer() was racing against itself and while the spinlock
serialized the tv1[] timer link list, timer_pending() called outside the
spinlock, cached timer link list element in a register.
With low register pressure (and a deep register file), lack of barrier
in raw_local_irqsave() as well as preempt_disable (!PREEMPT_COUNT
version), there was nothing to force gcc to reload across the spinlock,
causing a stale value in reg be used for link list manipulation - ensuing
a corruption.
ARcompact disassembly which shows the culprit generated code:
mod_timer:
push_s blink
mov_s r13,r0 # timer, timer
..
###### timer_pending( )
ld_s r3,[r13] # <------ <variable>.entry.next LOADED
brne r3, 0, @.L163
.L163:
..
###### spin_lock_irq( )
lr r5, [status32] # flags
bic r4, r5, 6 # temp, flags,
and.f 0, r5, 6 # flags,
flag.nz r4
###### detach_if_pending( ) begins
tst_s r3,r3 <--------------
# timer_pending( ) checks timer->entry.next
# r3 is NOT reloaded by gcc, using stale value
beq.d @.L169
mov.eq r0,0
##### detach_timer( ): __list_del( )
ld r4,[r13,4] # <variable>.entry.prev, D.31439
st r4,[r3,4] # <variable>.prev, D.31439
st r3,[r4] # <variable>.next, D.30246
We initially tried to fix this by adding barrier() to preempt_* macros
for !PREEMPT_COUNT but Linus clarified that it was anything but wrong.
http://www.spinics.net/lists/kernel/msg1512709.html
[vgupta: updated commitlog]
Reported-by/Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Cc: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Debugged-by/Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The mxs fixes for 3.9, take 4:
- A couple mxs boards that run I2C at 400 kHz experience some unstable
issue occasionally. Slow down the clock speed to have I2C work
reliably.
* tag 'mxs-fixes-3.9-4' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: Slow down the I2C clock speed
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Let's do the changes properly and fix the same problem everywhere, not
just for one case.
Cc: <stable@vger.kernel.org> # kernels containing 15e0d9e37c or equivalent
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
performed before the ANDCOND test
Some versions of pHyp will perform the adjunct partition test before the
ANDCOND test. The result of this is that H_RESOURCE can be returned and
cause the BUG_ON condition to occur. The HPTE is not removed. So add a
check for H_RESOURCE, it is ok if this HPTE is not removed as
pSeries_lpar_hpte_remove is looking for an HPTE to remove and not a
specific HPTE to remove. So it is ok to just move on to the next slot
and try again.
Cc: stable@vger.kernel.org
Signed-off-by: Michael Wolf <mjw@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
Pull KVM fix from Gleb Natapov:
"Bugfix for the regression introduced by commit c300aa64ddf5"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Allow cross page reads and writes from cached translations.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"Two quite small fixes: one a build problem, and the other fixes
seccomp filters on x32."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix rebuild with EFI_STUB enabled
x86: remove the x32 syscall bitmask from syscall_get_nr()
|
|
Interrupt handlers are always invoked with interrupts disabled, so
remove all uses of the deprecated IRQF_DISABLED flag.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Linux has expected that interrupt handlers are executed with local
interrupts disabled for a while now, so ensure that this is the case on
Alpha even for non-device interrupts such as IPIs.
Without this patch, secondary boot results in the following backtrace:
warning: at kernel/softirq.c:139 __local_bh_enable+0xb8/0xd0()
trace:
__local_bh_enable+0xb8/0xd0
irq_enter+0x74/0xa0
scheduler_ipi+0x50/0x100
handle_ipi+0x84/0x260
do_entint+0x1ac/0x2e0
irq_exit+0x60/0xa0
handle_irq+0x98/0x100
do_entint+0x2c8/0x2e0
ret_from_sys_call+0x0/0x10
load_balance+0x3e4/0x870
cpu_idle+0x24/0x80
rcu_eqs_enter_common.isra.38+0x0/0x120
cpu_idle+0x40/0x80
rest_init+0xc0/0xe0
_stext+0x1c/0x20
A similar dump occurs if you try to reboot using magic-sysrq.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Due to all of the goodness being packed into today's kernels, the
resulting image isn't as slim as it once was.
In light of this, don't pass -msmall-data to gcc, which otherwise results
in link failures due to impossible relocations when compiling anything but
the most trivial configurations.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Tested-by: Thorsten Kranzkowski <dl8bcu@dl8bcu.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixes a NULL pointer dereference at boot on UP1500.
Cc: stable@vger.kernel.org
Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Jay Estabrook <jay.estabrook@gmail.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds support for kvm_gfn_to_hva_cache_init functions for
reads and writes that will cross a page. If the range falls within
the same memslot, then this will be a fast operation. If the range
is split between two memslots, then the slower kvm_read_guest and
kvm_write_guest are used.
Tested: Test against kvm_clock unit tests.
Signed-off-by: Andrew Honig <ahonig@google.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
|
|
eboot.o and efi_stub_$(BITS).o didn't get added to "targets", and hence
their .cmd files don't get included by the build machinery, leading to
the files always getting rebuilt.
Rather than adding the two files individually, take the opportunity and
add $(VMLINUX_OBJS) to "targets" instead, thus allowing the assignment
at the top of the file to be shrunk quite a bit.
At the same time, remove a pointless flags override line - the variable
assigned to was misspelled anyway, and the options added are
meaningless for assembly sources.
[ hpa: the patch is not minimal, but I am taking it for -urgent anyway
since the excess impact of the patch seems to be small enough. ]
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/515C5D2502000078000CA6AD@nat28.tlf.novell.com
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Pull MIPS fixes from Ralf Baechle:
"Fixes for a number of small glitches in various corners of the MIPS
tree. No particular areas is standing out.
With this applied all MIPS defconfigs are building fine. No merge
conflicts are expected."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Delete definition of SA_RESTORER.
MIPS: Fix ISA level which causes secondary cache init bypassing and more
MIPS: Fix build error cavium-octeon without CONFIG_SMP
MIPS: Kconfig: Rename SNIPROM too
MIPS: Alchemy: Fix typo "CONFIG_DEBUG_PCI"
MIPS: Unbreak function tracer for 64-bit kernel.
|
|
SA_RESTORER used to be defined as 0x04000000 but only the O32 ABI ever
supported its use and no libc was using it, so the entire sa-restorer
functionality was removed with lmo commit 39bffc12c3580ab [Zap sa_restorer.]
for 2.5.48 retaining only the SA_RESTORER definition as a reminder to avoid
accidental reuse of the mask bit.
Upstream cdef9602fbf1871a43f0f1b5cea10dd0f275167d [signal: always clear
sa_restorer on execve] adds code that assumes sa_sigaction has an
sa_restorer field, if SA_RESTORER is defined which would break MIPS.
So remove the SA_RESTORER definition before the v3.8.4 merge.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit 17da8d63add23830892ac4dc2cbb3b5d4ffb79a8)
|
|
The commit a96102be70 introduced set_isa() where compatible ISA info is
also set aside from the one gets passed in. It means, for example, 1004K
will have MIPS_CPU_ISA_M32R2/M32R1/II/I flags. This leads to things like
the following inappropriate:
if (c->isa_level == MIPS_CPU_ISA_M32R1 ||
c->isa_level == MIPS_CPU_ISA_M32R2 ||
c->isa_level == MIPS_CPU_ISA_M64R1 ||
c->isa_level == MIPS_CPU_ISA_M64R2)
This patch fixes it.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Singed-off-by: EunBong Song <eunb.song@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
CONFIG_SNIPROM was renamed to CONFIG_FW_SNIPROM in v3.8. Let's rename
SNIPROM itself too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-mips@linux-mips.org;
Cc: linux-kernel@vger.kernel.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 7517de348663b08a808aff44b5300e817157a568 ("MIPS: Alchemy: Redo
PCI as platform driver") added a reference to CONFIG_DEBUG_PCI. Change
it to CONFIG_PCI_DEBUG, as that is a valid Kconfig macro.
Also add a newline to a debugging printk that this fix enables.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 58b69401c797 [MIPS: Function tracer: Fix broken function tracing]
completely broke the function tracer for 64-bit kernels. The symptom is
a system hang very early in the boot process.
The fix: Remove/fix $sp adjustments for 64-bit case.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Al Cooper <alcooperx@gmail.com>
Cc: viric@viric.name
Cc: stable@vger.kernel.org # 3.8.x
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Pull ARM fixes from Russell King:
"Another round of ARM fixes, which include:
- Fixing a problem with LPAE mapping sections
- Reporting of some hwcaps on Krait CPUs
- Avoiding repetitive warnings in the breakpoint code
- Fixing a build error noticed on Dove platforms with PJ4 CPUs
- Fix masking of level 2 cache revision.
- Fixing timer-based udelay()
- A larger fix for an erratum causing people major grief with Cortex
A15 CPUs"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7690/1: mm: fix CONFIG_LPAE typos
ARM: 7689/1: add unwind annotations to ftrace asm
ARM: 7685/1: delay: use private ticks_per_jiffy field for timer-based delay ops
ARM: 7684/1: errata: Workaround for Cortex-A15 erratum 798181 (TLBI/DSB operations)
ARM: 7682/1: cache-l2x0: fix masking of RTL revision numbering and set_debug init
ARM: iWMMXt: always enable iWMMXt support with PJ4 CPUs
ARM: 7681/1: hw_breakpoint: use warn_once to avoid spam from reset_ctrl_regs()
ARM: 7678/1: Work around faulty ISAR0 register in some Krait CPUs
ARM: 7680/1: Detect support for SDIV/UDIV from ISAR0 register
ARM: 7679/1: Clear IDIVT hwcap if CONFIG_ARM_THUMB=n
ARM: 7677/1: LPAE: Fix mapping in alloc_init_section for unaligned addresses
ARM: KVM: vgic: take distributor lock on sync_hwstate path
ARM: KVM: vgic: force EOIed LRs to the empty state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Just a bunch of bugfixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: provide emtpy check_pgt_cache() function
s390/uaccess: fix page table walk
s390/3270: fix minor_start issue
s390/uaccess: fix clear_user_pt()
s390/scm_blk: fix error return code in scm_blk_init()
s390/scm_block: fix printk format string
drivers/Kconfig: add several missing GENERIC_HARDIRQS dependencies
|
|
CONFIG_LPAE doesn't exist: the correct option is CONFIG_ARM_LPAE, so fix
up the two typos under arch/arm/.
The fix to head.S is slightly scary, but this is just for setting up
an early io-mapping for the serial port when running on a big-endian,
LPAE system. Since these systems don't exist in the wild (at least, I
have no access to one outside of kvmtool, which doesn't provide a serial
port suitable for earlyprintk), then we can revisit the code later if it
causes any problems.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add unwind annotations to the ftrace assembly code so that the function
tracer's stacktracing options (func_stack_trace, etc.) work when
CONFIG_ARM_UNWIND is enabled.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 70264367a243 ("ARM: 7653/2: do not scale loops_per_jiffy when
using a constant delay clock") fixed a problem with our timer-based
delay loop, where loops_per_jiffy is scaled by cpufreq yet used directly
by the timer delay ops.
This patch fixes the problem in a more elegant way by keeping a private
ticks_per_jiffy field in the delay ops, independent of loops_per_jiffy
and therefore not subject to scaling. The loop-based delay continues to
use loops_per_jiffy directly, as it should.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
operations)
On Cortex-A15 (r0p0..r3p2) the TLBI/DSB are not adequately shooting down
all use of the old entries. This patch implements the erratum workaround
which consists of:
1. Dummy TLBIMVAIS and DSB on the CPU doing the TLBI operation.
2. Send IPI to the CPUs that are running the same mm (and ASID) as the
one being invalidated (or all the online CPUs for global pages).
3. CPU receiving the IPI executes a DMB and CLREX (part of the exception
return code already).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
init
Commit b8db6b8 (ARM: 7547/4: cache-l2x0: add support for Aurora L2 cache
ctrl) moved the masking of the part ID which caused the RTL version to be
lost. Commit 6248d06 (ARM: 7545/1: cache-l2x0: make outer_cache_fns a
field of l2x0_of_data) changed how .set_debug is initialized. Both commits
break commit 74ddcdb (ARM: 7608/1: l2x0: Only set .set_debug
on PL310 r3p0 and earlier) which uses the RTL version to conditionally set
.set_debug function pointer. Commit b8db6b8 also caused the printed cache
ID to be missing the version information.
Fix this by reverting how the part number is masked so the RTL version
info is maintained. The cache-id-part DT property does not set the RTL
bits so masking them should have no effect. Also, re-arrange the order
of the function pointer init so the .set_debug function can be overridden.
Reported-by: Paolo Pisati <paolo.pisati@canonical.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Jason Cooper reports these build errors:
arch/arm/kernel/built-in.o: In function `iwmmxt_do':
/.../arch/arm/kernel/pj4-cp0.c:36: undefined reference to `iwmmxt_task_release'
/.../arch/arm/kernel/pj4-cp0.c:40: undefined reference to `iwmmxt_task_switch'
make: *** [vmlinux] Error 1
This is caused because the PJ4 code explicitly references the iWMMXt
code, but doesn't require it to be built. Fix this by ensuring that
iWMMXt is always enabled with PJ4.
Reported-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Pull MIPS fixes from Ralf Baechle:
"A collection of fixes pretty much across the MIPS code. Even the
change to include/linux/signal.h by David Howells' 2a1486981c13 ("Fix
breakage in MIPS siginfo handling") should be considered MIPS-specific
as it touches an ifdefed segment that is only relevant to MIPS and
which unfortunately can't be made to go away entirely."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
Fix breakage in MIPS siginfo handling
Revert "MIPS: BCM63XX: Call board_register_device from device_initcall()"
MIPS: BCM63XX: Make nvram checksum failure non fatal
MIPS: Fix code generation for non-DSP capable CPUs
MIPS: Fix inconsistent formatting inside /proc/cpuinfo
MIPS: SEAD3: Enable LL/SC.
MIPS: Get rid of CONFIG_CPU_HAS_LLSC again
MIPS: Add dependencies for HAVE_ARCH_TRANSPARENT_HUGEPAGE
MIPS: VR4133: Fix probe for LL/SC.
MIPS: Fix logic errors in bitops.c
MIPS: Use CONFIG_CPU_MIPSR2 in csum_partial.S
MIPS: compat: Return same error ENOSYS as native for invalid operation.
|
|
Slow down the I2C clock speed on M28 and SPS1 as it turns out the
I2C block in i.MX28 can not operate stable enough with the bus
running at 400kHz. Note that the driver used by Freescale runs
the bus at 250kHz when 400kHz speed is selected, but the mainline
Linux kernel runs the bus at actual 400kHz and that's where it is
occasionally unstable. Play safe and run the bus at 100kHz.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Commit fca460f95e928bae373daa8295877b6905bc62b8 simplified the x32
implementation by creating a syscall bitmask, equal to 0x40000000, that
could be applied to x32 syscalls such that the masked syscall number
would be the same as a x86_64 syscall. While that patch was a nice
way to simplify the code, it went a bit too far by adding the mask to
syscall_get_nr(); returning the masked syscall numbers can cause
confusion with callers that expect syscall numbers matching the x32
ABI, e.g. unmasked syscall numbers.
This patch fixes this by simply removing the mask from syscall_get_nr()
while preserving the other changes from the original commit. While
there are several syscall_get_nr() callers in the kernel, most simply
check that the syscall number is greater than zero, in this case this
patch will have no effect. Of those remaining callers, they appear
to be few, seccomp and ftrace, and from my testing of seccomp without
this patch the original commit definitely breaks things; the seccomp
filter does not correctly filter the syscalls due to the difference in
syscall numbers in the BPF filter and the value from syscall_get_nr().
Applying this patch restores the seccomp BPF filter functionality on
x32.
I've tested this patch with the seccomp BPF filters as well as ftrace
and everything looks reasonable to me; needless to say general usage
seemed fine as well.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Link: http://lkml.kernel.org/r/20130215172143.12549.10292.stgit@localhost
Cc: <stable@vger.kernel.org>
Cc: Will Drewry <wad@chromium.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
provided pagetables.
Occassionaly on a DL380 G4 the guest would crash quite early with this:
(XEN) d244:v0: unhandled page fault (ec=0003)
(XEN) Pagetable walk from ffffffff84dc7000:
(XEN) L4[0x1ff] = 00000000c3f18067 0000000000001789
(XEN) L3[0x1fe] = 00000000c3f14067 000000000000178d
(XEN) L2[0x026] = 00000000dc8b2067 0000000000004def
(XEN) L1[0x1c7] = 00100000dc8da067 0000000000004dc7
(XEN) domain_crash_sync called from entry.S
(XEN) Domain 244 (vcpu#0) crashed on cpu#3:
(XEN) ----[ Xen-4.1.3OVM x86_64 debug=n Not tainted ]----
(XEN) CPU: 3
(XEN) RIP: e033:[<ffffffff81263f22>]
(XEN) RFLAGS: 0000000000000216 EM: 1 CONTEXT: pv guest
(XEN) rax: 0000000000000000 rbx: ffffffff81785f88 rcx: 000000000000003f
(XEN) rdx: 0000000000000000 rsi: 00000000dc8da063 rdi: ffffffff84dc7000
The offending code shows it to be a loop writting the value zero
(%rax) in the %rdi (the L4 provided by Xen) register:
0: 44 00 00 add %r8b,(%rax)
3: 31 c0 xor %eax,%eax
5: b9 40 00 00 00 mov $0x40,%ecx
a: 66 0f 1f 84 00 00 00 nopw 0x0(%rax,%rax,1)
11: 00 00
13: ff c9 dec %ecx
15:* 48 89 07 mov %rax,(%rdi) <-- trapping instruction
18: 48 89 47 08 mov %rax,0x8(%rdi)
1c: 48 89 47 10 mov %rax,0x10(%rdi)
which fails. xen_setup_kernel_pagetable recycles some of the Xen's
page-table entries when it has switched over to its Linux page-tables.
Right before try to clear the page, we make a hypercall to change
it from _RO to _RW and that works (otherwise we would hit an BUG()).
And the _RW flag is set for that page:
(XEN) L1[0x1c7] = 001000004885f067 0000000000004dc7
The error code is 3, so PFEC_page_present and PFEC_write_access, so page is
present (correct), and we tried to write to the page, but a violation
occurred. The one theory is that the the page entries in hardware
(which are cached) are not up to date with what we just set. Especially
as we have just done an CR3 write and flushed the multicalls.
This patch does solve the problem by flusing out the TLB page
entry after changing it from _RO to _RW and we don't hit this
issue anymore.
Fixed-Oracle-Bug: 16243091 [ON OCCASIONS VM START GOES INTO
'CRASH' STATE: CLEAR_PAGE+0X12 ON HP DL380 G4]
Reported-and-Tested-by: Saar Maoz <Saar.Maoz@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
