summaryrefslogtreecommitdiff
path: root/drivers/ata
AgeCommit message (Collapse)AuthorFilesLines
2018-08-24Merge branch 'for-4.19' of ↵Linus Torvalds30-120/+158
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata updates from Tejun Heo: "Nothing too interesting. Mostly ahci and ahci_platform changes, many around power management" * 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits) ata: ahci_platform: enable to get and control reset ata: libahci_platform: add reset control support ata: add an extra argument to ahci_platform_get_resources() ata: sata_rcar: Add r8a77965 support ata: sata_rcar: exclude setting of PHY registers in Gen3 ata: sata_rcar: really mask all interrupts on Gen2 and later Revert "ata: ahci_platform: allow disabling of hotplug to save power" ata: libahci: Allow reconfigure of DEVSLP register ata: libahci: Correct setting of DEVSLP register ata: ahci: Enable DEVSLP by default on x86 with SLP_S0 ata: ahci: Support state with min power but Partial low power state Revert "ata: ahci_platform: convert kcalloc to devm_kcalloc" ata: sata_rcar: Add rudimentary Runtime PM support ata: sata_rcar: Provide a short-hand for &pdev->dev ata: Only output sg element mapped number in verbose debug ata: Guard ata_scsi_dump_cdb() by ATA_VERBOSE_DEBUG ata: ahci_platform: convert kcalloc to devm_kcalloc ata: ahci_platform: convert kzallloc to kcalloc ata: ahci_platform: correct parameter documentation for ahci_platform_shutdown libata: remove ata_sff_data_xfer_noirq() ...
2018-08-23Merge tag 'armsoc-drivers' of ↵Linus Torvalds1-1/+0
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver updates from Olof Johansson: "Some of the larger changes this merge window: - Removal of drivers for Exynos5440, a Samsung SoC that never saw widespread use. - Uniphier support for USB3 and SPI reset handling - Syste control and SRAM drivers and bindings for Allwinner platforms - Qualcomm AOSS (Always-on subsystem) reset controller drivers - Raspberry Pi hwmon driver for voltage - Mediatek pwrap (pmic) support for MT6797 SoC" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits) drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests soc: fsl: cleanup Kconfig menu soc: fsl: dpio: Convert DPIO documentation to .rst staging: fsl-mc: Remove remaining files staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl staging: fsl-dpaa2: eth: move generic FD defines to DPIO soc: fsl: qe: gpio: Add qe_gpio_set_multiple usb: host: exynos: Remove support for Exynos5440 clk: samsung: Remove support for Exynos5440 soc: sunxi: Add the A13, A23 and H3 system control compatibles reset: uniphier: add reset control support for SPI cpufreq: exynos: Remove support for Exynos5440 ata: ahci-platform: Remove support for Exynos5440 soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs soc: mediatek: pwrap: fix cipher init setting error dt-bindings: pwrap: mediatek: add pwrap support for MT6797 reset: uniphier: add USB3 core reset control dt-bindings: reset: uniphier: add USB3 core reset support ...
2018-08-22ata: ahci_platform: enable to get and control resetKunihiko Hayashi1-1/+2
Unlike SoC-specific driver, generic ahci_platform driver doesn't have any chances to control resets. This adds AHCI_PLATFORM_GET_RESETS to ahci_platform_get_resources() on the generic driver to enable reset control support. Suggested-by: Hans de Goede <hdegoede@redhat.com> Cc: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-08-22ata: libahci_platform: add reset control supportKunihiko Hayashi2-5/+27
Add support to get and control a list of resets for the device as optional and shared. These resets must be kept de-asserted until the device is enabled. This is specified as shared because some SoCs like UniPhier series have common reset controls with all ahci controller instances. However, according to Thierry's view, https://www.spinics.net/lists/linux-ide/msg55357.html some hardware-specific drivers already use their own resets, and the common reset make a path to occur double controls of resets. The ahci_platform_get_resources() can get and control the reset only when the second argument includes AHCI_PLATFORM_GET_RESETS bit. Suggested-by: Hans de Goede <hdegoede@redhat.com> Cc: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-08-22ata: add an extra argument to ahci_platform_get_resources()Kunihiko Hayashi15-15/+17
Add an extra argument to ahci_platform_get_resources(), that is for the bitmap representing the resource to get in this function. Currently there is no resources to be defined, so all the callers set '0' to the argument. Suggested-by: Hans de Goede <hdegoede@redhat.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-08-18Merge tag 'char-misc-4.19-rc1' of ↵Linus Torvalds2-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the bit set of char/misc drivers for 4.19-rc1 There is a lot here, much more than normal, seems like everyone is writing new driver subsystems these days... Anyway, major things here are: - new FSI driver subsystem, yet-another-powerpc low-level hardware bus - gnss, finally an in-kernel GPS subsystem to try to tame all of the crazy out-of-tree drivers that have been floating around for years, combined with some really hacky userspace implementations. This is only for GNSS receivers, but you have to start somewhere, and this is great to see. Other than that, there are new slimbus drivers, new coresight drivers, new fpga drivers, and loads of DT bindings for all of these and existing drivers. All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits) android: binder: Rate-limit debug and userspace triggered err msgs fsi: sbefifo: Bump max command length fsi: scom: Fix NULL dereference misc: mic: SCIF Fix scif_get_new_port() error handling misc: cxl: changed asterisk position genwqe: card_base: Use true and false for boolean values misc: eeprom: assignment outside the if statement uio: potential double frees if __uio_register_device() fails eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency misc: ti-st: Fix memory leak in the error path of probe() android: binder: Show extra_buffers_size in trace firmware: vpd: Fix section enabled flag on vpd_section_destroy platform: goldfish: Retire pdev_bus goldfish: Use dedicated macros instead of manual bit shifting goldfish: Add missing includes to goldfish.h mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux dt-bindings: mux: add adi,adgs1408 Drivers: hv: vmbus: Cleanup synic memory free path Drivers: hv: vmbus: Remove use of slow_virt_to_phys() Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind() ...
2018-08-16Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds2-2/+3
Pull SCSI updates from James Bottomley: "This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx, hisi_sas, smartpqi, megaraid_sas, arcmsr. In addition, with the continuing absence of Nic we have target updates for tcmu and target core (all with reviews and acks). The biggest observable change is going to be that we're (again) trying to switch to mulitqueue as the default (a user can still override the setting on the kernel command line). Other major core stuff is the removal of the remaining Microchannel drivers, an update of the internal timers and some reworks of completion and result handling" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits) scsi: core: use blk_mq_run_hw_queues in scsi_kick_queue scsi: ufs: remove unnecessary query(DM) UPIU trace scsi: qla2xxx: Fix issue reported by static checker for qla2x00_els_dcmd2_sp_done() scsi: aacraid: Spelling fix in comment scsi: mpt3sas: Fix calltrace observed while running IO & reset scsi: aic94xx: fix an error code in aic94xx_init() scsi: st: remove redundant pointer STbuffer scsi: qla2xxx: Update driver version to 10.00.00.08-k scsi: qla2xxx: Migrate NVME N2N handling into state machine scsi: qla2xxx: Save frame payload size from ICB scsi: qla2xxx: Fix stalled relogin scsi: qla2xxx: Fix race between switch cmd completion and timeout scsi: qla2xxx: Fix Management Server NPort handle reservation logic scsi: qla2xxx: Flush mailbox commands on chip reset scsi: qla2xxx: Fix unintended Logout scsi: qla2xxx: Fix session state stuck in Get Port DB scsi: qla2xxx: Fix redundant fc_rport registration scsi: qla2xxx: Silent erroneous message scsi: qla2xxx: Prevent sysfs access when chip is down scsi: qla2xxx: Add longer window for chip reset ...
2018-08-15Merge tag 'sound-4.19-rc1' of ↵Linus Torvalds1-9/+1
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound updates from Takashi Iwai: "It's been busy summer weeks and hence lots of changes, partly for a few new drivers and partly for a wide range of fixes. Here are highlights: ALSA Core: - Fix rawmidi buffer management, code cleanup / refactoring - Fix the SG-buffer page handling with incorrect fallback size - Fix the stall at virmidi trigger callback with a large buffer; also offloading and code-refactoring along with it - Various ALSA sequencer code cleanups ASoC: - Deploy the standard snd_pcm_stop_xrun() helper in several drivers - Support for providing name prefixes to generic component nodes - Quite a few fixes for DPCM as it gains a bit wider use and more robust testing - Generalization of the DIO2125 support to a simple amplifier driver - Accessory detection support for the audio graph card - DT support for PXA AC'97 devices - Quirks for a number of new x86 systems - Support for AM Logic Meson, Everest ES7154, Intel systems with RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707 HD-audio: - Code refactoring in HD-audio ext codec codes to drop own classes; preliminary works for the upcoming legacy codec support - Generalized DRM audio component for the upcoming radeon / amdgpu support - Unification of mic mute-LED and GPIO support for various codecs - Further improvement of CA0132 codec support including Recon3D - Proper vga_switcheroo handling for AMD i-GPU - Update of model list in documentation - Fixups for another HP Spectre x360, Conexant codecs, power-save blacklist update USB-audio: - Fix the invalid sample rate setup with external clock - Support of UAC3 selector units and processing units - Basic UAC3 power-domain support - Support for Encore mDSD and Thesycon-based DSD devices - Preparation for future complete callback changes Firewire: - Add support for MOTU Traveler Misc: - The endianess notation fixes in various drivers - Add fall-through comment in lots of drivers - Various sparse warning fixes, e.g. about PCM format types" * tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (529 commits) ASoC: adav80x: mark expected switch fall-through ASoC: da7219: Add delays to capture path to remove DC offset noise ALSA: usb-audio: Mark expected switch fall-through ALSA: mixart: Mark expected switch fall-through ALSA: opl3: Mark expected switch fall-through ALSA: hda/ca0132 - Add exit commands for Recon3D ALSA: hda/ca0132 - Change mixer controls for Recon3D ALSA: hda/ca0132 - Add Recon3D input and output select commands ALSA: hda/ca0132 - Add DSP setup defaults for Recon3D ALSA: hda/ca0132 - Add Recon3D startup functions and setup ALSA: hda/ca0132 - Add bool variable to enable/disable pci region2 mmio ALSA: hda/ca0132 - Add Recon3D pincfg ALSA: hda/ca0132 - Add quirk ID and enum for Recon3D ALSA: hda/ca0132 - Add alt_functions unsolicited response ALSA: hda/ca0132 - Clean up ca0132_init function. ALSA: hda/ca0132 - Create mmio gpio function to make code clearer ASoC: wm_adsp: Make DSP name configurable by codec driver ASoC: wm_adsp: Declare firmware controls from codec driver ASoC: max98373: Added software reset register to readable registers ASoC: wm_adsp: Correct DSP pointer for preloader control ...
2018-08-09Merge branch 'asoc-4.19' into asoc-nextMark Brown1-9/+1
2018-08-06ata: sata_rcar: exclude setting of PHY registers in Gen3Masaharu Hayakawa1-2/+2
According to documentation, setting of PHY registers is unnecessary with R-Car Gen3. The registers are not even described. So, don't initialize them. Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com> [wsa: updated commit message] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-08-06ata: sata_rcar: really mask all interrupts on Gen2 and laterWolfram Sang1-7/+13
Since R-Car Gen2, a new bit has been introduced to the interrupt mask register. Update the code to handle it properly as well. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-08-06Revert "ata: ahci_platform: allow disabling of hotplug to save power"Tejun Heo2-74/+19
This reverts commit aece27a2f01be4bb7683790f69cd1bed3a0929a2. Causes boot failure on some devices. http://lore.kernel.org/r/CA+G9fYuKW_jCFZPqG4tz=QY9ROfHO38KiCp9XTA+KaDOFVtcqQ@mail.gmail.com Signed-off-by: Tejun Heo <tj@kernel.org>
2018-08-06Merge tag 'v4.18-rc6' into for-4.19/block2Jens Axboe9-47/+98
Pull in 4.18-rc6 to get the NVMe core AEN change to avoid a merge conflict down the line. Signed-of-by: Jens Axboe <axboe@kernel.dk>
2018-08-03libata-scsi: Move sense buffers onto stackKees Cook1-12/+6
To support future compile-time sizeof() checks that will be able to validate the length of sense buffers, this removes the only dynamically allocated sense buffers in the tree by putting the 96 byte sense buffers on the stack. Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-07-30ata: libahci: Allow reconfigure of DEVSLP registerSrinivas Pandruvada1-8/+10
There are two modes in which DEVSLP can be entered. The OS initiated or hardware autonomous. In hardware autonomous mode, BIOS configures the AHCI controller and the device to enable DEVSLP. But they may not be ideal for all cases. So in this case, OS should be able to reconfigure DEVSLP register. Currently if the DEVSLP is already enabled, we can't set again as it will simply return. There are some systems where the firmware is setting high DITO by default, in this case we can't modify here to correct settings. With the default in several seconds, we are not able to transition to DEVSLP. This change will allow reconfiguration of devslp register if DITO is different. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-30ata: libahci: Correct setting of DEVSLP registerSrinivas Pandruvada1-0/+2
We have seen that on some platforms, SATA device never show any DEVSLP residency. This prevent power gating of SATA IP, which prevent system to transition to low power mode in systems with SLP_S0 aka modern standby systems. The PHY logic is off only in DEVSLP not in slumber. Reference: https://www.intel.com/content/dam/www/public/us/en/documents/datasheets /332995-skylake-i-o-platform-datasheet-volume-1.pdf Section 28.7.6.1 Here driver is trying to do read-modify-write the devslp register. But not resetting the bits for which this driver will modify values (DITO, MDAT and DETO). So simply reset those bits before updating to new values. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-30ata: ahci: Enable DEVSLP by default on x86 with SLP_S0Srinivas Pandruvada1-5/+33
One of the requirement for modern x86 system to enter lowest power mode (SLP_S0) is SATA IP block to be off. This is true even during when platform is suspended to idle and not only in opportunistic (runtime) suspend. Several of these system don't have traditional ACPI S3, so it is important that they enter SLP_S0 state, to avoid draining battery even during suspend. So it is important that out of the box Linux installation reach this state. SATA IP block doesn't get turned off till SATA is in DEVSLP mode. Here user has to either use scsi-host sysfs or tools like powertop to set the sata-host link_power_management_policy to min_power. This change sets by default link power management policy to min_power with partial (preferred) or slumber support on idle for some platforms. To avoid regressions, the following conditions are used: - User didn't override the policy from module parameter - The kernel config is already set to use med_power_with_dipm or deeper - System is a SLP_S0 capable using ACPI low power idle flag This combination will make sure that systems are fairly recent and since getting shipped with SLP_S0 support, the DEVSLP function is already validated. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-30ata: ahci: Support state with min power but Partial low power stateSrinivas Pandruvada3-1/+6
Currently when min_power policy is selected, the partial low power state is not entered and link will try aggressively enter to only slumber state. Add a new policy which still enable DEVSLP but also try to enter partial low power state. This policy is presented as "min_power_with_partial". For information the difference between partial and slumber Partial – PHY logic is powered up, and in a reduced power state. The link PM exit latency to active state maximum is 10 ns. Slumber – PHY logic is powered up, and in a reduced power state. The link PM exit latency to active state maximum is 10 ms. Devslp – PHY logic is powered down. The link PM exit latency from this state to active state maximum is 20 ms, unless otherwise specified by DETO. Suggested-and-reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-24Revert "ata: ahci_platform: convert kcalloc to devm_kcalloc"Corentin Labbe1-1/+7
Since ahci_platform_put_resources() use target_pwrs after "devm_" freed it, we cannot use devm_kcalloc for allocating target_pwrs. This reverts commit bd0038b1b4f499d814d8f33a55b1df5ea6cf3b85. Reported-and-reviwed-by: Mikko Perttunen <mperttunen@nvidia.com> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-23ata: sata_rcar: Add rudimentary Runtime PM supportGeert Uytterhoeven1-22/+18
Replace the explicit clock handling to enable/disable the SATA module by calls to Runtime PM. This makes the driver independent of actual SoC clock/power hierarchies, and is needed to support virtualization, where the guest is not in full control of power management. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-23ata: sata_rcar: Provide a short-hand for &pdev->devGeert Uytterhoeven1-8/+8
No functional changes. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-17ata: ahci-platform: Remove support for Exynos5440Krzysztof Kozlowski1-1/+0
The Exynos5440 is not actively developed, there are no development boards available and probably there are no real products with it. Remove wide-tree support for Exynos5440. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org>
2018-07-16Merge 4.18-rc5 into char-misc-nextGreg Kroah-Hartman9-47/+98
We want the char-misc fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-12ata: Only output sg element mapped number in verbose debugPaul Menzel1-1/+1
Defining `ATA_DEBUG` there are a lof of messages like below in the log. [ 16.345472] ata_sg_setup: 1 sg elements mapped As that is too verbose, only output these messages in verbose debug. Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-12ata: Guard ata_scsi_dump_cdb() by ATA_VERBOSE_DEBUGPaul Menzel1-2/+2
Defining `ATA_DEBUG` nothing can be really seen, as the log is spammed with CDB messages. Therefore, guard the print by `ATA_VERBOSE_DEBUG`. Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-12ata: ahci_platform: convert kcalloc to devm_kcallocCorentin Labbe1-3/+1
Like phys, target_pwrs could be allocated with devm_ function Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-12ata: ahci_platform: convert kzallloc to kcallocCorentin Labbe1-5/+3
It's better to kcalloc instead of kzalloc(n * sizeof()) Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-12ata: ahci_platform: correct parameter documentation for ahci_platform_shutdownCorentin Labbe1-1/+1
The documentation about parameter for ahci_platform_shutdown has a typo. This fix the following build warning: drivers/ata/libahci_platform.c:693: warning: Function parameter or member 'pdev' not described in 'ahci_platform_shutdown' drivers/ata/libahci_platform.c:693: warning: Excess function parameter 'dev' description in 'ahci_platform_shutdow Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-11libata: remove ata_sff_data_xfer_noirq()Sebastian Andrzej Siewior9-40/+10
ata_sff_data_xfer_noirq() is invoked via the ->sff_data_xfer hook. The latter is invoked by ata_pio_sector(), atapi_send_cdb() and __atapi_pio_bytes() which in turn is invoked by ata_sff_hsm_move(). The latter function requires that the "ap->lock" lock is held which needs to be taken with disabled interrupts. There is no need have to have ata_sff_data_xfer_noirq() which invokes ata_sff_data_xfer32() with disabled interrupts because at this point the interrupts are already disabled. Remove the function and its references to it and replace all callers with ata_sff_data_xfer32(). Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-07headers: separate linux/mod_devicetable.h from linux/platform_device.hRandy Dunlap2-0/+2
At over 4000 #includes, <linux/platform_device.h> is the 9th most #included header file in the Linux kernel. It does not need <linux/mod_devicetable.h>, so drop that header and explicitly add <linux/mod_devicetable.h> to source files that need it. 4146 #include <linux/platform_device.h> After this patch, there are 225 files that use <linux/mod_devicetable.h>, for a reduction of around 3900 times that <linux/mod_devicetable.h> does not have to be read & parsed. 225 #include <linux/mod_devicetable.h> This patch was build-tested on 20 different arch-es. It also makes these drivers SubmitChecklist#1 compliant. Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/ Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-02ata: Remove depends on HAS_DMA in case of platform dependencyGeert Uytterhoeven1-2/+0
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST". In most cases this other symbol is an architecture or platform specific symbol, or PCI. Generic symbols and drivers without platform dependencies keep their dependencies on HAS_DMA, to prevent compiling subsystems or drivers that cannot work anyway. This simplifies the dependencies, and allows to improve compile-testing. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Mark Brown <broonie@kernel.org> Acked-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-02ata: Fix ZBC_OUT all bit handlingDamien Le Moal1-3/+8
If the ALL bit is set in the ZBC_OUT command, the command zone ID field (block) should be ignored. Reported-by: David Butterfield <david.butterfield@wdc.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Cc: stable@vger.kernel.org Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-02ata: Fix ZBC_OUT command block checkDamien Le Moal1-6/+7
The block (LBA) specified must not exceed the last addressable LBA, which is dev->nr_sectors - 1. So fix the correct check is "if (block >= dev->n_sectors)" and not "if (block > dev->n_sectords)". Additionally, the asc/ascq to return for an LBA that is not a zone start LBA should be ILLEGAL REQUEST, regardless if the bad LBA is out of range. Reported-by: David Butterfield <david.butterfield@wdc.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Cc: stable@vger.kernel.org Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-02ahci: Add Intel Ice Lake LP PCI IDMika Westerberg1-0/+1
This should also be using the default LPM policy for mobile chipsets so add the PCI ID to the driver list of supported devices. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
2018-07-02ahci: Disable LPM on Lenovo 50 series laptops with a too old BIOSHans de Goede2-0/+62
There have been several reports of LPM related hard freezes about once a day on multiple Lenovo 50 series models. Strange enough these reports where not disk model specific as LPM issues usually are and some users with the exact same disk + laptop where seeing them while other users where not seeing these issues. It turns out that enabling LPM triggers a firmware bug somewhere, which has been fixed in later BIOS versions. This commit adds a new ahci_broken_lpm() function and a new ATA_FLAG_NO_LPM for dealing with this. The ahci_broken_lpm() function contains DMI match info for the 4 models which are known to be affected by this and the DMI BIOS date field for known good BIOS versions. If the BIOS date is older then the one in the table LPM will be disabled and a warning will be printed. Note the BIOS dates are for known good versions, some older versions may work too, but we don't know for sure, the table is using dates from BIOS versions for which users have confirmed that upgrading to that version makes the problem go away. Unfortunately I've been unable to get hold of the reporter who reported that BIOS version 2.35 fixed the problems on the W541 for him. I've been able to verify the DMI_SYS_VENDOR and DMI_PRODUCT_VERSION from an older dmidecode, but I don't know the exact BIOS date as reported in the DMI. Lenovo keeps a changelog with dates in their release notes, but the dates there are the release dates not the build dates which are in DMI. So I've chosen to set the date to which we compare to one day past the release date of the 2.34 BIOS. I plan to fix this with a follow up commit once I've the necessary info. Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-07-02sata_nv: remove redundant pointers sdev0 and sdev1Colin Ian King1-3/+0
Pointers sdev0 and sdev1 are being assigned but are never used hence they are redundant and can be removed. Cleans up clang warnings: warning: variable 'sdev0' set but not used [-Wunused-but-set-variable] warning: variable 'sdev1' set but not used [-Wunused-but-set-variable] Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-06-20scsi: libsas: dynamically allocate and free ata hostJason Yan2-2/+3
Commit 2623c7a5f2 ("libata: add refcounting to ata_host") v4.17+ introduced refcounting to ata_host and will increase or decrease the refcount when adding or deleting transport ATA port. Now the ata host for libsas is embedded in domain_device, and the ->kref member is not initialized. Afer we add ata transport class, ata_host_get() will be called when adding transport ATA port and a warning will be triggered as below: refcount_t: increment on 0; use-after-free. WARNING: CPU: 2 PID: 103 at lib/refcount.c:153 refcount_inc+0x40/0x48 ...... Call trace: refcount_inc+0x40/0x48 ata_host_get+0x10/0x18 ata_tport_add+0x40/0x120 ata_sas_tport_add+0xc/0x14 sas_ata_init+0x7c/0xc8 sas_discover_domain+0x380/0x53c process_one_work+0x12c/0x288 worker_thread+0x58/0x3f0 kthread+0xfc/0x128 ret_from_fork+0x10/0x18 And also when removing transport ATA port ata_host_put() will be called and another similar warning will be triggered. If the refcount decreased to zero, the ata host will be freed. But this ata host is only part of domain_device, it cannot be freed directly. So we have to change this embedded static ata host to a dynamically allocated ata host and initialize the ->kref member. To use ata_host_get() and ata_host_put() in libsas, we need to move the declaration of these functions to the public libata.h and export them. Fixes: b6240a4df018 ("scsi: libsas: add transport class for ATA devices") Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Taras Kondratiuk <takondra@cisco.com> CC: Tejun Heo <tj@kernel.org> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-06-19sata_fsl: remove dead code in tag retrievalJens Axboe1-6/+0
We can never pass in the internal tag to this helper, it'll always be the hardware tag. So there's no need to check and do an internal translation of that tag. Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-06-19sata_fsl: convert to command iteratorJens Axboe1-2/+1
We need to iterate all commands, including the internal one, for ATAPI error handling. Fixes: 28361c403683 ("libata: add extra internal command") Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-06-19libata: convert eh to command iteratorsJens Axboe1-25/+16
Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-06-18ata: pata_pxa: remove the dmaengine compat needRobert Jarzmik1-9/+1
As the pxa architecture switched towards the dmaengine slave map, the old compatibility mechanism to acquire the dma requestor line number and priority are not needed anymore. This patch simplifies the dma resource acquisition, using the more generic function dma_request_slave_channel(). Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
2018-06-18ata: ahci_mvebu: ahci_mvebu_stop_engine() can be staticWei Yongjun1-1/+1
Fixes the following sparse warning: drivers/ata/ahci_mvebu.c:85:5: warning: symbol 'ahci_mvebu_stop_engine' was not declared. Should it be static? Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-06-18libahci: Fix possible Spectre-v1 pmp indexing in ahci_led_store()John Garry1-2/+5
Currently smatch warns of possible Spectre-V1 issue in ahci_led_store(): drivers/ata/libahci.c:1150 ahci_led_store() warn: potential spectre issue 'pp->em_priv' (local cap) Userspace controls @pmp from following callchain: em_message->store() ->ata_scsi_em_message_store() -->ap->ops->em_store() --->ahci_led_store() After the mask+shift @pmp is effectively an 8b value, which is used to index into an array of length 8, so sanitize the array index. Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-06-18ata: ahci_platform: allow disabling of hotplug to save powerSamuel Morris2-19/+74
A number of resources remain powered to support hotplug. On platforms I've worked with, allowing the ahci_platform to suspend saves about 150mW. This patch enables rpm and allows the device to be auto-suspended through sysfs. Signed-off-by: Samuel Morris <samorris@lexmark.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-06-18ata: ahci: rpm_put port on port_stop to match rpm_get in port_startSamuel Morris1-0/+2
This change balances out the final ahci_port_resume in port_start to ensure reference counts are correct after port stop. Signed-off-by: Samuel Morris <samorris@lexmark.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2018-06-13treewide: devm_kzalloc() -> devm_kcalloc()Kees Cook1-4/+4
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc(). This patch replaces cases of: devm_kzalloc(handle, a * b, gfp) with: devm_kcalloc(handle, a * b, gfp) as well as handling cases of: devm_kzalloc(handle, a * b * c, gfp) with: devm_kzalloc(handle, array3_size(a, b, c), gfp) as it's slightly less ugly than: devm_kcalloc(handle, array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: devm_kzalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. Some manual whitespace fixes were needed in this patch, as Coccinelle really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...". The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( devm_kzalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | devm_kzalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( devm_kzalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ - devm_kzalloc + devm_kcalloc (HANDLE, - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( devm_kzalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression HANDLE; expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, sizeof(THING) * C2, ...) | devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...) | devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, C1 * C2, ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * E2 + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * (E2) + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-13treewide: kzalloc() -> kcalloc()Kees Cook2-2/+2
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-10Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds1-0/+12
Pull SCSI updates from James Bottomley: "This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc, xfcp, hisi_sas, cxlflash, qla2xxx. In the absence of Nic, we're also taking target updates which are mostly minor except for the tcmu refactor. The only real core change to worry about is the removal of high page bouncing (in sas, storvsc and iscsi). This has been well tested and no problems have shown up so far" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (268 commits) scsi: lpfc: update driver version to 12.0.0.4 scsi: lpfc: Fix port initialization failure. scsi: lpfc: Fix 16gb hbas failing cq create. scsi: lpfc: Fix crash in blk_mq layer when executing modprobe -r lpfc scsi: lpfc: correct oversubscription of nvme io requests for an adapter scsi: lpfc: Fix MDS diagnostics failure (Rx < Tx) scsi: hisi_sas: Mark PHY as in reset for nexus reset scsi: hisi_sas: Fix return value when get_free_slot() failed scsi: hisi_sas: Terminate STP reject quickly for v2 hw scsi: hisi_sas: Add v2 hw force PHY function for internal ATA command scsi: hisi_sas: Include TMF elements in struct hisi_sas_slot scsi: hisi_sas: Try wait commands before before controller reset scsi: hisi_sas: Init disks after controller reset scsi: hisi_sas: Create a scsi_host_template per HW module scsi: hisi_sas: Reset disks when discovered scsi: hisi_sas: Add LED feature for v3 hw scsi: hisi_sas: Change common allocation mode of device id scsi: hisi_sas: change slot index allocation mode scsi: hisi_sas: Introduce hisi_sas_phy_set_linkrate() scsi: hisi_sas: fix a typo in hisi_sas_task_prep() ...
2018-06-06Merge branch 'for-4.18' of ↵Linus Torvalds12-151/+166
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata updates from Tejun Heo: - libata has always been limiting the maximum queue depth to 31, with one entry set aside mostly for historical reasons. This didn't use to make much difference but Jens found out that modern hard drives can actually perform measurably better with the extra one queue depth. Jens updated libata core so that it can make use of full 32 queue depth - Damien updated command retry logic in error handling so that it doesn't unnecessarily retry when upper layer (SCSI) is gonna handle them - A couple misc changes * 'for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: sata_fsl: use the right type for tag bitshift ahci: enable full queue depth of 32 libata: don't clamp queue depth to ATA_MAX_QUEUE - 1 libata: add extra internal command sata_nv: set host can_queue count appropriately libata: remove assumption that ATA_MAX_QUEUE - 1 is the max libata: use ata_tag_internal() consistently libata: bump ->qc_active to a 64-bit type libata: convert core and drivers to ->hw_tag usage libata: introduce notion of separate hardware tags libata: Fix command retry decision libata: Honor RQF_QUIET flag libata: Make ata_dev_set_mode() less verbose libata: Fix ata_err_string() libata: Fix comment typo in ata_eh_analyze_tf() sata_nv: don't use block layer bounce buffer ata: hpt37x: Convert to use match_string() helper
2018-06-06Merge branch 'for-4.17-fixes' of ↵Linus Torvalds2-4/+1
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata fixes from Tejun Heo: "These two are fixes which missed v4.17. One is to remove an incorrect power management blacklist entry and the other to fix a cdb buffer overrun which has been there for a very long time" * 'for-4.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: libata: Drop SanDisk SD7UB3Q*G1001 NOLPM quirk libata: zpodd: small read overflow in eject_tray()