summaryrefslogtreecommitdiff
path: root/drivers/bluetooth
AgeCommit message (Collapse)AuthorFilesLines
2022-11-03Bluetooth: virtio_bt: Use skb_put to set lengthSoenke Huster1-1/+1
By using skb_put we ensure that skb->tail is set correctly. Currently, skb->tail is always zero, which leads to errors, such as the following page fault in rfcomm_recv_frame: BUG: unable to handle page fault for address: ffffed1021de29ff #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page RIP: 0010:rfcomm_run+0x831/0x4040 (net/bluetooth/rfcomm/core.c:1751) Fixes: afd2daa26c7a ("Bluetooth: Add support for virtio transport driver") Signed-off-by: Soenke Huster <soenke.huster@eknoes.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-19Bluetooth: hci_{ldisc,serdev}: check percpu_init_rwsem() failureTetsuo Handa2-5/+12
syzbot is reporting NULL pointer dereference at hci_uart_tty_close() [1], for rcu_sync_enter() is called without rcu_sync_init() due to hci_uart_tty_open() ignoring percpu_init_rwsem() failure. While we are at it, fix that hci_uart_register_device() ignores percpu_init_rwsem() failure and hci_uart_unregister_device() does not call percpu_free_rwsem(). Link: https://syzkaller.appspot.com/bug?extid=576dfca25381fb6fbc5f [1] Reported-by: syzbot <syzbot+576dfca25381fb6fbc5f@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Fixes: 67d2f8781b9f00d1 ("Bluetooth: hci_ldisc: Allow sleeping while proto locks are held.") Fixes: d73e172816652772 ("Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-14Bluetooth: btusb: Add a new VID/PID 0e8d/0608 for MT7921Daniel Golle1-0/+3
Add a new PID/VID 0e8d/0608 for MT7921K chip found on AMD RZ608 module. From /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0e8d ProdID=0608 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-14Bluetooth: btusb: Add a new PID/VID 13d3/3583 for MT7921Sean Wang1-0/+3
Add VID 13D3 & PID 3583 for MediaTek MT7921 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=03 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3583 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-09Bluetooth: btintel: Mark Intel controller to support LE_STATES quirkKiran K1-9/+8
HarrrisonPeak, CyclonePeak, SnowFieldPeak and SandyPeak controllers are marked to support HCI_QUIRK_LE_STATES. Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-09Bluetooth: btintel: Add support for MagnetorKiran K1-0/+3
Hardware variant for Magnetor core (CNVi) is added. Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-09Bluetooth: btusb: Add a new PID/VID 13d3/3578 for MT7921Chris Lu1-0/+3
Add VID 13D3 & PID 3578 for MediaTek MT7921 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=03 Lev=01 Prnt=01 Port=07 Cnt=03 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3578 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-02Bluetooth: btusb: mediatek: fix WMT failure during runtime suspendSean Wang1-0/+14
WMT cmd/event doesn't follow up the generic HCI cmd/event handling, it needs constantly polling control pipe until the host received the WMT event, thus, we should require to specifically acquire PM counter on the USB to prevent the interface from entering auto suspended while WMT cmd/event in progress. Fixes: a1c49c434e15 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices") Co-developed-by: Jing Cai <jing.cai@mediatek.com> Signed-off-by: Jing Cai <jing.cai@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-01Bluetooth: btusb: Add BT device 0cb8:c549 from RTW8852AE to tablesLarry Finger1-0/+2
A new Bluetooth device for the Realtek RTW8852AE has been noted. This device has the following lsusb output: Bus 001 Device 003: ID 0cb8:c549 Opticis Co., Ltd Bluetooth Radio The pertinent part of /sys/kernel/debug/usb/devices is as follows: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cb8 ProdID=c549 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-01Bluetooth: btusb: Add RTL8761BUV device (Edimax BT-8500)Szabolcs Sipos1-0/+2
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=7392 ProdID=c611 Rev= 2.00 S: Manufacturer=Realtek S: Product=Edimax Bluetooth Adapter S: SerialNumber=XXXXXXXXXXXX C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Szabolcs Sipos <labuwx@balfug.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-01Bluetooth: btusb: RTL8761BUV consistent namingSzabolcs Sipos1-5/+1
Based on photos available from the FCC, all currently supported RTL8761B series USB dongles have the same chip: RTL8761BUV. rtl8761bu is often used to refer to this chip. rtl8761b sometimes refers to this chip, and other times to its UART variant (RTL8761BTV). +----------------+---------+---------+---------------+ | Dongle | USB VID | USB PID | FCC ID | +----------------+---------+---------+---------------+ | ASUS USB-BT500 | 0x0b05 | 0x190e | MSQ-USBBTJB00 | | TP-Link UB500 | 0x2357 | 0x0604 | 2AXJ4UB500 | | EDUP EP-B3519 | | | 2AHRD-EPB3519 | | EDUP EP-B3536 | | | 2AHRDEP-B3536 | | UGREEN CM390 | | | 2AQI5-CM390 | +----------------+---------+---------+---------------+ Signed-off-by: Szabolcs Sipos <labuwx@balfug.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-01Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3592Max Chou1-0/+2
Add the support ID(0x13D3, 0x3592) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3592 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-08-26Bluetooth: Add VID/PID 0489/e0e0 for MediaTek MT7921Fae1-0/+3
Tested on HP Envy ey0xxx output from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0e0 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Fae <faenkhauser@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-08-04Merge tag 'spdx-6.0-rc1' of ↵Linus Torvalds5-72/+5
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx Pull SPDX updates from Greg KH: "Here is the set of SPDX comment updates for 6.0-rc1. Nothing huge here, just a number of updated SPDX license tags and cleanups based on the review of a number of common patterns in GPLv2 boilerplate text. Also included in here are a few other minor updates, two USB files, and one Documentation file update to get the SPDX lines correct. All of these have been in the linux-next tree for a very long time" * tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits) Documentation: samsung-s3c24xx: Add blank line after SPDX directive x86/crypto: Remove stray comment terminator treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2) treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1) treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE ...
2022-07-23Bluetooth: btusb: Detect if an ACL packet is in fact an ISO packetLuiz Augusto von Dentz1-0/+10
Fix up the packet type if ISO packets are sent over the bulk endpoint. Note: This is a stopgap since the Bluetooth specification currently doesn't define any endpoint to transport ISO packets. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-23Bluetooth: btusb: Add support for ISO packetsLuiz Augusto von Dentz1-0/+14
This enabled btusb driver to properly transmit ISO packets. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: btrtl: Fix typo in commentshaomin Deng1-1/+1
Delete the repeated word "that" in comments. Signed-off-by: shaomin Deng <dengshaomin@cdjrlc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for fake CSRZijun Hu1-1/+0
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting" instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so remove this unnecessary quirk for fake CSR controllers. Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for QCAZijun Hu1-1/+0
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting" instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so remove this unnecessary quirk for QCA controllers. The reason why these two HCI commands are broken for QCA controllers is that feature "Erroneous Data Reporting" is not enabled by their firmware as shown by below log: @ RAW Open: hcitool (privileged) version 2.22 < HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0 > HCI Event: Command Complete (0x0e) plen 68 Read Local Supported Commands (0x04|0x0002) ncmd 1 Status: Success (0x00) Commands: 288 entries ...... Read Default Erroneous Data Reporting (Octet 18 - Bit 2) Write Default Erroneous Data Reporting (Octet 18 - Bit 3) ...... < HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0 > HCI Event: Command Complete (0x0e) plen 4 Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1 Status: Unknown HCI Command (0x01) < HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 > HCI Event: Command Complete (0x0e) plen 12 Read Local Supported Features (0x04|0x0003) ncmd 1 Status: Success (0x00) Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87 3 slot packets ...... Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Tested-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: btusb: Add a new VID/PID 0489/e0e2 for MT7922He Wang1-0/+3
Add VID/PID 0489:e0e2 for MediaTek MT7922 Bluetooth chip. Found and tested with Asus UM5302TA. From /sys/kernel/debug/usb/devices: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0e2 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: He Wang <xw897002528@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: btusb: Set HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for MTKYuri D'Elia1-0/+1
This sets HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for MTK controllers since SCO appear to not work when using HCI_OP_ENHANCED_SETUP_SYNC_CONN. Link: https://bugzilla.kernel.org/show_bug.cgi?id=215576 Signed-off-by: Yuri D'Elia <wavexx@thregr.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: hci_bcm: Increase host baudrate for CYW55572 in autobaud modeHakan Jansson1-4/+16
Add device specific data for max baudrate in autobaud mode. This allows the host to use a baudrate higher than "init speed" when loading FW in autobaud mode. The device specific max baudrate in autobaud mode for CYW55572 is set to 921600 bps. Devices without device specific max baudrate in autobaud mode will use init speed as before. If no device specific init speed has been specified, it will default to the bcm_proto default 115200 bps. The increased baud rate improves FW load time. The exact load time will depend on the specific system and FW being used. As a rough indication, the FW load time dropped from ~9s @ 115.2kbps to ~1.7s @ 921.6kbps in one test. Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: hci_bcm: Prevent early baudrate setting in autobaud modeHakan Jansson1-4/+1
Always prevent trying to set device baudrate before calling setup() when using autobaud mode. This was previously happening for devices which had device specific data with member no_early_set_baudrate set to 0. Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: hci_bcm: Add DT compatible for CYW55572Hakan Jansson1-0/+1
CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon. Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3586Hilda Wu1-0/+2
Add the support ID(0x13D3, 0x3586) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3586 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3587Hilda Wu1-0/+2
Add the support ID(0x13D3, 0x3587) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3587 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: btusb: Add Realtek RTL8852C support ID 0x0CB8:0xC558Hilda Wu1-0/+2
Add the support ID(0x0CB8, 0xC558) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cb8 ProdID=c558 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: btusb: Add Realtek RTL8852C support ID 0x04C5:0x1675Hilda Wu1-0/+2
Add the support ID(0x04c5, 0x1675) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04c5 ProdID=1675 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: btusb: Add Realtek RTL8852C support ID 0x04CA:0x4007Hilda Wu1-0/+4
Add the support ID(0x04CA, 0x4007) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=4007 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: Add default wakeup callback for HCI UART driverYing Hsu1-0/+11
Bluetooth HCI devices indicate if they are able to wakeup in the wakeup callback since 'commit 4539ca67fe8e ("Bluetooth: Rename driver .prevent_wake to .wakeup")'. This patch adds a default wakeup callback for Bluetooth HCI UAR devices. It assumes Bluetooth HCI UART devices are wakeable for backward compatibility. For those who need a customized behavior, one can override it before calling hci_uart_register_device(). Fixes: 4539ca67fe8e ("Bluetooth: Rename driver .prevent_wake to .wakeup") Signed-off-by: Ying Hsu <yinghsu@chromium.org> Reviewed-by: Alain Michaud <alainm@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: btmtksdio: Add in-band wakeup supportSean Wang1-0/+15
Commit ce64b3e94919 ("Bluetooth: mt7921s: Support wake on bluetooth") adds the wake on bluethooth via a dedicated GPIO. Extend the wake-on-bluetooth to use the SDIO DAT1 pin (in-band wakeup), when supported by the SDIO host driver. Co-developed-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: hci_bcm: Add BCM4349B1 variantAhmad Fatoum2-0/+3
The BCM4349B1, aka CYW/BCM89359, is a WiFi+BT chip and its Bluetooth portion can be controlled over serial. Two subversions are added for the chip, because ROM firmware reports 002.002.013 (at least for the chips I have here), while depending on patchram firmware revision, either 002.002.013 or 002.002.014 is reported. Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-07-22Bluetooth: hci_intel: Add check for platform_driver_registerJiasheng Jiang1-1/+5
As platform_driver_register() could fail, it should be better to deal with the return value in order to maintain the code consisitency. Fixes: 1ab1f239bf17 ("Bluetooth: hci_intel: Add support for platform driver") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-07-22Bluetooth: hci_bcm: Add support for FW loading in autobaud modeHakan Jansson3-15/+40
Use the presence of a DT property, "brcm,requires-autobaud-mode", to enable startup in autobaud mode. If the property is present, the device is started in autobaud mode by asserting RTS (BT_UART_CTS_N) prior to powering on the device. Also prevent the use of unsupported commands for devices started in autobaud mode. Only a limited subset of HCI commands are supported in autobaud mode. Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading. Autobaud mode can also be required on some boards where the controller device is using a non-standard baud rate in normal mode when first powered on. Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-07-22Bluetooth: hci_qca: Return wakeup for qca_wakeupSai Teja Aluvala1-1/+1
This fixes the return value of qca_wakeup(), since .wakeup work inversely with original .prevent_wake. Fixes: 4539ca67fe8ed (Bluetooth: Rename driver .prevent_wake to .wakeup) Signed-off-by: Sai Teja Aluvala <quic_saluvala@quicinc.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-07-22Bluetooth: btusb: Add support of IMC Networks PID 0x3568Aaron Ma1-0/+3
It is 13d3:3568 for MediaTek MT7922 USB Bluetooth chip. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3568 Rev=01.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=... C: #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-06-10treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULEThomas Gleixner5-72/+5
Based on the normalized pattern: this software file (the file ) is distributed by marvell international ltd under the terms of the gnu general public license version 2 june 1991 (the license ) you may use redistribute and/or modify this file in accordance with the terms and conditions of the license a copy of which is available by writing to the free software foundation inc 51 franklin street fifth floor boston ma 02110-1301 usa or on the worldwide web at http://www gnu org/licenses/old-licenses/gpl-2 0 txt the file is distributed as-is without warranty of any kind and the implied warranties of merchantability or fitness for a particular purpose are expressly disclaimed the license provides additional details about this warranty disclaimer extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference. Reviewed-by: Allison Randal <allison@lohutok.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-05-13Bluetooth: btmtksdio: fix the reset takes too longSean Wang1-0/+5
Sending WMT command during the reset in progress is invalid and would get no response from firmware until the reset is complete, so we ignore the WMT command here to resolve the issue which causes the whole reset process taking too long. Fixes: 8fafe702253d ("Bluetooth: mt7921s: support bluetooth reset mechanism") Co-developed-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-05-13Bluetooth: btmtksdio: fix possible FW initialization failureSean Wang1-8/+8
According to FW advised sequence, mt7921s need to re-acquire privilege immediately after the firmware download is complete before normal running. Otherwise, it is still possible the bus may be stuck in an abnormal status that causes FW initialization failure in the current driver. Fixes: 752aea58489f ("Bluetooth: mt7921s: fix bus hang with wrong privilege") Co-developed-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-05-13Bluetooth: btmtksdio: fix use-after-free at btmtksdio_recv_eventSean Wang1-1/+2
We should not access skb buffer data anymore after hci_recv_frame was called. [ 39.634809] BUG: KASAN: use-after-free in btmtksdio_recv_event+0x1b0 [ 39.634855] Read of size 1 at addr ffffff80cf28a60d by task kworker [ 39.634962] Call trace: [ 39.634974] dump_backtrace+0x0/0x3b8 [ 39.634999] show_stack+0x20/0x2c [ 39.635016] dump_stack_lvl+0x60/0x78 [ 39.635040] print_address_description+0x70/0x2f0 [ 39.635062] kasan_report+0x154/0x194 [ 39.635079] __asan_report_load1_noabort+0x44/0x50 [ 39.635099] btmtksdio_recv_event+0x1b0/0x1c4 [ 39.635129] btmtksdio_txrx_work+0x6cc/0xac4 [ 39.635157] process_one_work+0x560/0xc5c [ 39.635177] worker_thread+0x7ec/0xcc0 [ 39.635195] kthread+0x2d0/0x3d0 [ 39.635215] ret_from_fork+0x10/0x20 [ 39.635247] Allocated by task 0: [ 39.635260] (stack is not available) [ 39.635281] Freed by task 2392: [ 39.635295] kasan_save_stack+0x38/0x68 [ 39.635319] kasan_set_track+0x28/0x3c [ 39.635338] kasan_set_free_info+0x28/0x4c [ 39.635357] ____kasan_slab_free+0x104/0x150 [ 39.635374] __kasan_slab_free+0x18/0x28 [ 39.635391] slab_free_freelist_hook+0x114/0x248 [ 39.635410] kfree+0xf8/0x2b4 [ 39.635427] skb_free_head+0x58/0x98 [ 39.635447] skb_release_data+0x2f4/0x410 [ 39.635464] skb_release_all+0x50/0x60 [ 39.635481] kfree_skb+0xc8/0x25c [ 39.635498] hci_event_packet+0x894/0xca4 [bluetooth] [ 39.635721] hci_rx_work+0x1c8/0x68c [bluetooth] [ 39.635925] process_one_work+0x560/0xc5c [ 39.635951] worker_thread+0x7ec/0xcc0 [ 39.635970] kthread+0x2d0/0x3d0 [ 39.635990] ret_from_fork+0x10/0x20 [ 39.636021] The buggy address belongs to the object at ffffff80cf28a600 which belongs to the cache kmalloc-512 of size 512 [ 39.636039] The buggy address is located 13 bytes inside of 512-byte region [ffffff80cf28a600, ffffff80cf28a800) Fixes: 9aebfd4a2200 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices") Co-developed-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-05-13Bluetooth: btbcm: Add entry for BCM4373A0 UART BluetoothTim Harvey1-0/+1
This patch adds the device ID for the BCM4373A0 module, found e.g. in the Infineon (Cypress) CYW4373E chip. The required firmware file is named 'BCM4373A0.hcd'. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-05-13Bluetooth: btusb: Add a new PID/VID 0489/e0c8 for MT7921Sean Wang1-0/+3
Add VID 0489 & PID e0c8 for MediaTek MT7921 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=13 Cnt=03 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0c8 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-05-13Bluetooth: btusb: Add 0x0bda:0x8771 Realtek 8761BUV devicesIsmael Luceno1-0/+4
Identifies as just "Realtek Semiconductor Corp. Bluetooth Radio"; it's used in many adapters, e.g.: - UGREEN CM390 - C-TECH BTD-01 - Orico BTA-508 - KS-is KS-457 Device description at /sys/kernel/debug/usb/devices: T: Bus=03 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=8771 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C239987 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Ismael Luceno <ismael@iodev.co.uk> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-05-13Bluetooth: btusb: Set HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for QCAZijun Hu1-0/+1
Set HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for QCA controllers since they answer HCI_OP_READ_DEF_ERR_DATA_REPORTING with error code "UNKNOWN HCI COMMAND" as shown below: [ 580.517552] Bluetooth: hci0: unexpected cc 0x0c5a length: 1 < 2 [ 580.517660] Bluetooth: hci0: Opcode 0x c5a failed: -38 hcitool -i hci0 cmd 0x03 0x5a < HCI Command: ogf 0x03, ocf 0x005a, plen 0 > HCI Event: 0x0e plen 4 01 5A 0C 01 btmon log: < HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0 > HCI Event: Command Complete (0x0e) plen 4 Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1 Status: Unknown HCI Command (0x01) Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-05-13Bluetooth: btusb: add support for Qualcomm WCN785xZijun Hu1-2/+8
Qualcomm WCN785x has PID/VID 0cf3/e700 as shown by /sys/kernel/debug/usb/devices: T: Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 8 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e700 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-05-13Bluetooth: btrtl: Add support for RTL8852CMax Chou1-0/+13
Add the support for RTL8852C BT controller on USB interface. The necessary firmware file will be submitted to linux-firmware. Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-05-13Bluetooth: btusb: Set HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for QCALuiz Augusto von Dentz1-0/+5
This sets HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for QCA controllers since SCO appear to not work when using HCI_OP_ENHANCED_SETUP_SYNC_CONN. Link: https://bugzilla.kernel.org/show_bug.cgi?id=215576 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-05-13Bluetooth: hci_qca: Use del_timer_sync() before freeingSteven Rostedt1-2/+2
While looking at a crash report on a timer list being corrupted, which usually happens when a timer is freed while still active. This is commonly triggered by code calling del_timer() instead of del_timer_sync() just before freeing. One possible culprit is the hci_qca driver, which does exactly that. Eric mentioned that wake_retrans_timer could be rearmed via the work queue, so also move the destruction of the work queue before del_timer_sync(). Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: stable@vger.kernel.org Fixes: 0ff252c1976da ("Bluetooth: hciuart: Add support QCA chipset for UART") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-05-13Bluetooth: btintel: Constify static struct regmap_busRikard Falkeborn1-1/+1
The only usage of regmap_ibt is to (after the regmap_init() macro is expanded), pass its address to __regmap_init(), which takes a pointer to const struct regmap_bus as input. Make it const to allow the compiler to put it in read-only memory. Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-05-13Bluetooth: mt7921s: Fix the incorrect pointer checkSean Wang1-1/+1
Fix the incorrect pointer check on ven_data. Fixes: f41b91fa1783 ("Bluetooth: mt7921s: Add .btmtk_get_codec_config_data") Co-developed-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>