Age | Commit message (Collapse) | Author | Files | Lines |
|
commit e42acf104d6e0bd7ccd2f09103d5be5e6d3c637c upstream.
The current release locality code seems to be based on the
misunderstanding that the TPM interrupts when a locality is released:
it doesn't, only when the locality is acquired.
Furthermore, there seems to be no point in waiting for the locality to
be released. All it does is penalize the last TPM user. However, if
there's no next TPM user, this is a pointless wait and if there is a
next TPM user, they'll pay the penalty waiting for the new locality
(or possibly not if it's the same as the old locality).
Fix the code by making release_locality as simple write to release
with no waiting for completion.
Cc: stable@ger.kernel.org
Fixes: 33bafe90824b ("tpm_tis: verify locality released before returning from release_locality")
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d9ae54af1d02a7c0edc55c77d7df2b921e58a87 upstream.
The TPM TIS specification says the TPM signals the acquisition of locality
when the TMP_ACCESS_REQUEST_USE bit goes to one *and* the
TPM_ACCESS_REQUEST_USE bit goes to zero. Currently we only check the
former not the latter, so check both. Adding the check on
TPM_ACCESS_REQUEST_USE should fix the case where the locality is
re-requested before the TPM has released it. In this case the locality may
get released briefly before it is reacquired, which causes all sorts of
problems. However, with the added check, TPM_ACCESS_REQUEST_USE should
remain 1 until the second request for the locality is granted.
Cc: stable@ger.kernel.org
Fixes: 27084efee0c3 ("[PATCH] tpm: driver for next generation TPM chips")
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b154ce11ead925de6a94feb3b0317fafeefa0ebc ]
There is a misconfiguration in the bios of the gpio pin used for the
interrupt in the T490s. When interrupts are enabled in the tpm_tis
driver code this results in an interrupt storm. This was initially
reported when we attempted to enable the interrupt code in the tpm_tis
driver, which previously wasn't setting a flag to enable it. Due to
the reports of the interrupt storm that code was reverted and we went back
to polling instead of using interrupts. Now that we know the T490s problem
is a firmware issue, add code to check if the system is a T490s and
disable interrupts if that is the case. This will allow us to enable
interrupts for everyone else. If the user has a fixed bios they can
force the enabling of interrupts with tpm_tis.interrupts=1 on the
kernel command line.
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8ffd778aff45be760292225049e0141255d4ad6e ]
Mimic the pre-existing ACPI and Device Tree event log behavior by not
creating the binary_bios_measurements file when the EFI TPM event log is
empty.
This fixes the following NULL pointer dereference that can occur when
reading /sys/kernel/security/tpm0/binary_bios_measurements after the
kernel received an empty event log from the firmware:
BUG: kernel NULL pointer dereference, address: 000000000000002c
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 2 PID: 3932 Comm: fwupdtpmevlog Not tainted 5.9.0-00003-g629990edad62 #17
Hardware name: LENOVO 20LCS03L00/20LCS03L00, BIOS N27ET38W (1.24 ) 11/28/2019
RIP: 0010:tpm2_bios_measurements_start+0x3a/0x550
Code: 54 53 48 83 ec 68 48 8b 57 70 48 8b 1e 65 48 8b 04 25 28 00 00 00 48 89 45 d0 31 c0 48 8b 82 c0 06 00 00 48 8b 8a c8 06 00 00 <44> 8b 60 1c 48 89 4d a0 4c 89 e2 49 83 c4 20 48 83 fb 00 75 2a 49
RSP: 0018:ffffa9c901203db0 EFLAGS: 00010246
RAX: 0000000000000010 RBX: 0000000000000000 RCX: 0000000000000010
RDX: ffff8ba1eb99c000 RSI: ffff8ba1e4ce8280 RDI: ffff8ba1e4ce8258
RBP: ffffa9c901203e40 R08: ffffa9c901203dd8 R09: ffff8ba1ec443300
R10: ffffa9c901203e50 R11: 0000000000000000 R12: ffff8ba1e4ce8280
R13: ffffa9c901203ef0 R14: ffffa9c901203ef0 R15: ffff8ba1e4ce8258
FS: 00007f6595460880(0000) GS:ffff8ba1ef880000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000002c CR3: 00000007d8d18003 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
? __kmalloc_node+0x113/0x320
? kvmalloc_node+0x31/0x80
seq_read+0x94/0x420
vfs_read+0xa7/0x190
ksys_read+0xa7/0xe0
__x64_sys_read+0x1a/0x20
do_syscall_64+0x37/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xa9
In this situation, the bios_event_log pointer in the tpm_bios_log struct
was not NULL but was equal to the ZERO_SIZE_PTR (0x10) value. This was
due to the following kmemdup() in tpm_read_log_efi():
int tpm_read_log_efi(struct tpm_chip *chip)
{
...
/* malloc EventLog space */
log->bios_event_log = kmemdup(log_tbl->log, log_size, GFP_KERNEL);
if (!log->bios_event_log) {
ret = -ENOMEM;
goto out;
}
...
}
When log_size is zero, due to an empty event log from firmware,
ZERO_SIZE_PTR is returned from kmemdup(). Upon a read of the
binary_bios_measurements file, the tpm2_bios_measurements_start()
function does not perform a ZERO_OR_NULL_PTR() check on the
bios_event_log pointer before dereferencing it.
Rather than add a ZERO_OR_NULL_PTR() check in functions that make use of
the bios_event_log pointer, simply avoid creating the
binary_bios_measurements_file as is done in other event log retrieval
backends.
Explicitly ignore all of the events in the final event log when the main
event log is empty. The list of events in the final event log cannot be
accurately parsed without referring to the first event in the main event
log (the event log header) so the final event log is useless in such a
situation.
Fixes: 58cc1e4faf10 ("tpm: parse TPM event logs based on EFI table")
Link: https://lore.kernel.org/linux-integrity/E1FDCCCB-CA51-4AEE-AC83-9CDE995EAE52@canonical.com/
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Reported-by: Mimi Zohar <zohar@linux.ibm.com>
Cc: Thiébaud Weksteen <tweek@google.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d8d74ea3c00214aee1e1826ca18e77944812b9b4 ]
Synchronize with the results from the CRQs before continuing with
the initialization. This avoids trying to send TPM commands while
the rtce buffer has not been allocated, yet.
This patch fixes an existing race condition that may occurr if the
hypervisor does not quickly respond to the VTPM_GET_RTCE_BUFFER_SIZE
request sent during initialization and therefore the ibmvtpm->rtce_buf
has not been allocated at the time the first TPM command is sent.
Fixes: 132f76294744 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3ef193822b25e9ee629974f66dc1ff65167f770c ]
Bug link: https://bugzilla.kernel.org/show_bug.cgi?id=195657
cmd/rsp buffers are expected to be in the same ACPI region.
For Zen+ CPUs BIOS's might report two different regions, some of
them also report region sizes inconsistent with values from TPM
registers.
Memory configuration on ASRock x470 ITX:
db0a0000-dc59efff : Reserved
dc57e000-dc57efff : MSFT0101:00
dc582000-dc582fff : MSFT0101:00
Work around the issue by storing ACPI regions declared for the
device in a fixed array and adding an array for pointers to
corresponding possibly allocated resources in crb_map_io function.
This data was previously held for a single resource
in struct crb_priv (iobase field) and local variable io_res in
crb_map_io function. ACPI resources array is used to find index of
corresponding region for each buffer and make the buffer size
consistent with region's length. Array of pointers to allocated
resources is used to map the region at most once.
Signed-off-by: Ivan Lazeev <ivan.lazeev@gmail.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c4e79d99e6f42b79040f1a33cd4018f5425030b ]
The size of the buffers for storing context's and sessions can vary from
arch to arch as PAGE_SIZE can be anything between 4 kB and 256 kB (the
maximum for PPC64). Define a fixed buffer size set to 16 kB. This should be
enough for most use with three handles (that is how many we allow at the
moment). Parametrize the buffer size while doing this, so that it is easier
to revisit this later on if required.
Cc: stable@vger.kernel.org
Reported-by: Stefan Berger <stefanb@linux.ibm.com>
Fixes: 745b361e989a ("tpm: infrastructure for TPM spaces")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ccf6fb858e17a8f8a914a1c6444d277cfedfeae6 ]
Found by smatch:
drivers/char/tpm/tpm_tis_core.c:1088 tpm_tis_core_init() warn:
variable dereferenced before check 'chip->ops' (see line 979)
'chip->ops' is assigned in the beginning of function
in tpmm_chip_alloc->tpm_chip_alloc
and is used before first possible goto to error path.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit eba5cf3dcb844c82f54d4a857e124824e252206d upstream.
tpm_ibmvtpm_send() can fail during PowerVM Live Partition Mobility resume
with an H_CLOSED return from ibmvtpm_send_crq(). The PAPR says, 'The
"partner partition suspended" transport event disables the associated CRQ
such that any H_SEND_CRQ hcall() to the associated CRQ returns H_Closed
until the CRQ has been explicitly enabled using the H_ENABLE_CRQ hcall.'
This patch adds a check in tpm_ibmvtpm_send() for an H_CLOSED return from
ibmvtpm_send_crq() and in that case calls tpm_ibmvtpm_resume() and
retries the ibmvtpm_send_crq() once.
Cc: stable@vger.kernel.org # 3.7.x
Fixes: 132f76294744 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Reported-by: Linh Pham <phaml@us.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: George Wilson <gcwilson@linux.ibm.com>
Tested-by: Linh Pham <phaml@us.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b160c94be5d2816b62c8ac338605668304242959 upstream.
Call disable_interrupts() if we have to revert to polling in order not to
unnecessarily reserve the IRQ for the life-cycle of the driver.
Cc: stable@vger.kernel.org # 4.5.x
Reported-by: Hans de Goede <hdegoede@redhat.com>
Fixes: e3837e74a06d ("tpm_tis: Refactor the interrupt setup")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f9bf8adb55cd5a357b247a16aafddf8c97b276e0 upstream.
If .next function does not change position index,
following .show function will repeat output related
to current position index.
For /sys/kernel/security/tpm0/binary_bios_measurements:
1) read after lseek beyound end of file generates whole last line.
2) read after lseek to middle of last line generates
expected end of last line and unexpected whole last line once again.
Cc: stable@vger.kernel.org # 4.19.x
Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d7a47b96ed1102551eb7325f97937e276fb91045 upstream.
If .next function does not change position index,
following .show function will repeat output related
to current position index.
In case of /sys/kernel/security/tpm0/ascii_bios_measurements
and binary_bios_measurements:
1) read after lseek beyound end of file generates whole last line.
2) read after lseek to middle of last line generates
expected end of last line and unexpected whole last line once again.
Cc: stable@vger.kernel.org # 4.19.x
Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 805fa88e0780b7ce1cc9b649dd91a0a7164c6eb4 upstream.
If a TPM is in disabled state, it's reasonable for it to have an empty
log. Bailing out of probe in this case means that the PPI interface
isn't available, so there's no way to then enable the TPM from the OS.
In general it seems reasonable to ignore log errors - they shouldn't
interfere with any other TPM functionality.
Signed-off-by: Matthew Garrett <matthewgarrett@google.com>
Cc: stable@vger.kernel.org # 4.19.x
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1689114acc5e89a196fec6d732dae3e48edb6ad upstream.
devm_kcalloc() can fail and return NULL so we need to check for that.
Cc: stable@vger.kernel.org
Fixes: 58472f5cd4f6f ("tpm: validate TPM 2.0 commands")
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db4d8cb9c9f2af71c4d087817160d866ed572cc9 upstream
TPM 2.0 Shutdown involve sending TPM2_Shutdown to TPM chip and disabling
future TPM operations. TPM 1.2 behavior was different, future TPM
operations weren't disabled, causing rare issues. This patch ensures
that future TPM operations are disabled.
Fixes: d1bd4a792d39 ("tpm: Issue a TPM2_Shutdown for TPM2 devices.")
Cc: stable@vger.kernel.org
Signed-off-by: Vadim Sukhomlinov <sukhomlinov@google.com>
[dianders: resolved merge conflicts with mainline]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 2677ca98ae377517930c183248221f69f771c921 upstream
Use tpm_try_get_ops() in tpm-sysfs.c so that we can consider moving
other decorations (locking, localities, power management for example)
inside it. This direction can be of course taken only after other call
sites for tpm_transmit() have been treated in the same way.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8ab547a2dcfac6ec184a5e036e1093eb3f7a215c ]
* Rename TPM_BUFSIZE defined in drivers/char/tpm/st33zp24/st33zp24.h to
ST33ZP24_BUFSIZE.
* Rename TPM_BUFSIZE defined in drivers/char/tpm/tpm_i2c_infineon.c to
TPM_I2C_INFINEON_BUFSIZE.
* Rename TPM_RETRY in tpm_i2c_nuvoton to TPM_I2C_RETRIES.
* Remove TPM_HEADER_SIZE from tpm_i2c_nuvoton.
Cc: stable@vger.kernel.org
Fixes: bf38b8710892 ("tpm/tpm_i2c_stm_st33: Split tpm_i2c_tpm_st33 in 2 layers (core + phy)")
Fixes: aad628c1d91a ("char/tpm: Add new driver for Infineon I2C TIS TPM")
Fixes: 32d33b29ba07 ("TPM: Retry SaveState command in suspend path")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b9d0a85d6b2e76630cfd4c475ee3af4109bfd87a upstream
calc_tpm2_event_size() has an invalid signature because
it returns a 'size_t' where as its signature says that
it returns 'int'.
Cc: <stable@vger.kernel.org>
Fixes: 4d23cc323cdb ("tpm: add securityfs support for TPM 2.0 firmware event log")
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 442601e87a4769a8daba4976ec3afa5222ca211d ]
Return -E2BIG when the transfer is incomplete. The upper layer does
not retry, so not doing that is incorrect behaviour.
Cc: stable@vger.kernel.org
Fixes: a2871c62e186 ("tpm: Add support for Atmel I2C TPMs")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f5595f5baa30e009bf54d0d7653a9a0cc465be60 upstream.
The send() callback should never return length as it does not in every
driver except tpm_crb in the success case. The reason is that the main
transmit functionality only cares about whether the transmit was
successful or not and ignores the count completely.
Suggested-by: Stefan Berger <stefanb@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d7a850fdc1a2e4d2adbc95cc0fc962974725e88 upstream.
The current approach to read first 6 bytes from the response and then tail
of the response, can cause the 2nd memcpy_fromio() to do an unaligned read
(e.g. read 32-bit word from address aligned to a 16-bits), depending on how
memcpy_fromio() is implemented. If this happens, the read will fail and the
memory controller will fill the read with 1's.
This was triggered by 170d13ca3a2f, which should be probably refined to
check and react to the address alignment. Before that commit, on x86
memcpy_fromio() turned out to be memcpy(). By a luck GCC has done the right
thing (from tpm_crb's perspective) for us so far, but we should not rely on
that. Thus, it makes sense to fix this also in tpm_crb, not least because
the fix can be then backported to stable kernels and make them more robust
when compiled in differing environments.
Cc: stable@vger.kernel.org
Cc: James Morris <jmorris@namei.org>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Fixes: 30fc8d138e91 ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2ba5780ce30549cf57929b01d8cba6fe656e31c5 upstream.
tpm_i2c_nuvoton calculated commands duration using TPM 1.x
values via tpm_calc_ordinal_duration() also for TPM 2.x chips.
Call tpm2_calc_ordinal_duration() for retrieving ordinal
duration for TPM 2.X chips.
Cc: stable@vger.kernel.org
Cc: Nayna Jain <nayna@linux.vnet.ibm.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com> (For TPM 2.0)
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 01f54664a4db0d612de0ece8e0022f21f9374e9b upstream.
First, rename out_no_locality to out_locality for bailing out on
both tpm_cmd_ready() and tpm_request_locality() failure.
Second, ignore the return value of go_to_idle() as it may override
the return value of the actual tpm operation, the go_to_idle() error
will be caught on any consequent command.
Last, fix the wrong 'goto out', that jumped back instead of forward.
Cc: stable@vger.kernel.org
Fixes: 627448e85c76 ("tpm: separate cmd_ready/go_idle from runtime_pm")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84b59f6487d82d3ab4247a099aba66d4d17e8b08 upstream.
When checking whether the response is large enough to be able to contain
the received random bytes in tpm_get_random() and tpm2_get_random(),
they fail to take account the header size, which should be added to the
minimum size. This commit fixes this issue.
Cc: stable@vger.kernel.org
Fixes: c659af78eb7b ("tpm: Check size of response before accessing data")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e487a0f52301293152a6f8c4e217f2a11dd808e3 upstream.
Functionality of the xen-tpmfront driver was lost secondary to
the introduction of xenbus multi-page support in commit ccc9d90a9a8b
("xenbus_client: Extend interface to support multi-page ring").
In this commit pointer to location of where the shared page address
is stored was being passed to the xenbus_grant_ring() function rather
then the address of the shared page itself. This resulted in a situation
where the driver would attach to the vtpm-stubdom but any attempt
to send a command to the stub domain would timeout.
A diagnostic finding for this regression is the following error
message being generated when the xen-tpmfront driver probes for a
device:
<3>vtpm vtpm-0: tpm_transmit: tpm_send: error -62
<3>vtpm vtpm-0: A TPM error (-62) occurred attempting to determine
the timeouts
This fix is relevant to all kernels from 4.1 forward which is the
release in which multi-page xenbus support was introduced.
Daniel De Graaf formulated the fix by code inspection after the
regression point was located.
Fixes: ccc9d90a9a8b ("xenbus_client: Extend interface to support multi-page ring")
Signed-off-by: Dr. Greg Wettstein <greg@enjellic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[boris: Updated commit message, added Fixes tag]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
[ Upstream commit 0d6d0d62d9505a9816716aa484ebd0b04c795063 ]
For TPM 1.2 chips the system setup utility allows to set the TPM device in
one of the following states:
* Active: Security chip is functional
* Inactive: Security chip is visible, but is not functional
* Disabled: Security chip is hidden and is not functional
When choosing the "Inactive" state, the TPM 1.2 device is enumerated and
registered, but sending TPM commands fail with either TPM_DEACTIVATED or
TPM_DISABLED depending if the firmware deactivated or disabled the TPM.
Since these TPM 1.2 error codes don't have special treatment, inactivating
the TPM leads to a very noisy kernel log buffer that shows messages like
the following:
tpm_tis 00:05: 1.2 TPM (device-id 0x0, rev-id 78)
tpm tpm0: A TPM error (6) occurred attempting to read a pcr value
tpm tpm0: TPM is disabled/deactivated (0x6)
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting to read a pcr value
ima: No TPM chip found, activating TPM-bypass! (rc=6)
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting get random
Let's just suppress error log messages for the TPM_{DEACTIVATED,DISABLED}
return codes, since this is expected when the TPM 1.2 is set to Inactive.
In that case the kernel log is cleaner and less confusing for users, i.e:
tpm_tis 00:05: 1.2 TPM (device-id 0x0, rev-id 78)
tpm tpm0: TPM is disabled/deactivated (0x6)
ima: No TPM chip found, activating TPM-bypass! (rc=6)
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As TPM_TRANSMIT_RAW always requires also not to take locks for obvious
reasons (deadlock), this commit renames the flag as TPM_TRANSMIT_NESTED
and prevents taking tpm_mutex when the flag is given to tpm_transmit().
Suggested-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Convert tpm_find_get_ops() to use tpm_default_chip() in case no chip
is passed in.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Implement tpm_default_chip() to find the first TPM chip and return it to
the caller while increasing the reference count on its device. This
function can be used by other subsystems, such as IMA, to find the system's
default TPM chip and use it for all subsequent TPM operations.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Rename tpm_chip_find_get() to tpm_find_get_ops() to more closely match
the tpm_put_ops() counter part.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Adds plumbing required for drivers based on tpm_tis to set hwrng quality.
Signed-off-by: Louis Collard <louiscollard@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
The userpace expects to read the number of bytes stated in the header.
Returning the size of the buffer instead would be unexpected.
Cc: stable@vger.kernel.org
Fixes: 095531f891e6 ("tpm: return a TPM_RC_COMMAND_CODE response if command is not implemented")
Signed-off-by: Ricardo Schwarzmeier <Ricardo.Schwarzmeier@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Fix tpm ptt initialization error:
tpm tpm0: A TPM error (378) occurred get tpm pcr allocation.
We cannot use go_idle cmd_ready commands via runtime_pm handles
as with the introduction of localities this is no longer an optional
feature, while runtime pm can be not enabled.
Though cmd_ready/go_idle provides a power saving, it's also a part of
TPM2 protocol and should be called explicitly.
This patch exposes cmd_read/go_idle via tpm class ops and removes
runtime pm support as it is not used by any driver.
When calling from nested context always use both flags:
TPM_TRANSMIT_UNLOCKED and TPM_TRANSMIT_RAW. Both are needed to resolve
tpm spaces and locality request recursive calls to tpm_transmit().
TPM_TRANSMIT_RAW should never be used standalone as it will fail
on double locking. While TPM_TRANSMIT_UNLOCKED standalone should be
called from non-recursive locked contexts.
New wrappers are added tpm_cmd_ready() and tpm_go_idle() to
streamline tpm_try_transmit code.
tpm_crb no longer needs own power saving functions and can drop using
tpm_pm_suspend/resume.
This patch cannot be really separated from the locality fix.
Fixes: 888d867df441 (tpm: cmd_ready command can be issued only after granting locality)
Cc: stable@vger.kernel.org
Fixes: 888d867df441 (tpm: cmd_ready command can be issued only after granting locality)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
An SPI TPM device managed directly on an embedded board using
the SPI bus and some GPIO or similar line as IRQ handler will
pass the IRQn from the TPM device associated with the SPI
device. This is already handled by the SPI core, so make sure
to pass this down to the core as well.
(The TPM core habit of using -1 to signal no IRQ is dubious
(as IRQ 0 is NO_IRQ) but I do not want to mess with that
semantic in this patch.)
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
In order to make struct tpm_buf the first class object for constructing
TPM commands, migrate tpm2_get_random() to use it. In addition, removed
remaining references to struct tpm2_cmd. All of them use it to acquire
the length of the response, which can be achieved by using
tpm_buf_length().
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Nayna Jain<nayna@linux.vnet.ibm.com>
|
|
In order to make struct tpm_buf the first class object for constructing TPM
commands, migrate tpm2_get_tpm_pt() to use it.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Tested-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
|
|
In order to make struct tpm_buf the first class object for constructing TPM
commands, migrate tpm2_probe() to use it.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Jay Freyensee <why2jjj.linux@gmail.com>
Reviewed-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Tested-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
|
|
In order to make struct tpm_buf the first class object for constructing TPM
commands, migrated tpm2_shutdown() to use it.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Tested-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
|
|
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc().
This patch replaces cases of:
devm_kzalloc(handle, a * b, gfp)
with:
devm_kcalloc(handle, a * b, gfp)
as well as handling cases of:
devm_kzalloc(handle, a * b * c, gfp)
with:
devm_kzalloc(handle, array3_size(a, b, c), gfp)
as it's slightly less ugly than:
devm_kcalloc(handle, array_size(a, b), c, gfp)
This does, however, attempt to ignore constant size factors like:
devm_kzalloc(handle, 4 * 1024, gfp)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
Some manual whitespace fixes were needed in this patch, as Coccinelle
really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...".
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
expression HANDLE;
type TYPE;
expression THING, E;
@@
(
devm_kzalloc(HANDLE,
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
devm_kzalloc(HANDLE,
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression HANDLE;
expression COUNT;
typedef u8;
typedef __u8;
@@
(
devm_kzalloc(HANDLE,
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(char) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
expression HANDLE;
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)
// 2-factor product, only identifiers.
@@
expression HANDLE;
identifier SIZE, COUNT;
@@
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- SIZE * COUNT
+ COUNT, SIZE
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression HANDLE;
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
devm_kzalloc(HANDLE,
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression HANDLE;
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
expression HANDLE;
identifier STRIDE, SIZE, COUNT;
@@
(
devm_kzalloc(HANDLE,
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression HANDLE;
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
devm_kzalloc(HANDLE,
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression HANDLE;
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@
(
devm_kzalloc(HANDLE, sizeof(THING) * C2, ...)
|
devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...)
|
devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
devm_kzalloc(HANDLE, C1 * C2, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- (E1) * E2
+ E1, E2
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- (E1) * (E2)
+ E1, E2
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- E1 * E2
+ E1, E2
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
There is a race condition in tpm_common_write function allowing
two threads on the same /dev/tpm<N>, or two different applications
on the same /dev/tpmrm<N> to overwrite each other commands/responses.
Fixed this by taking the priv->buffer_mutex early in the function.
Also converted the priv->data_pending from atomic to a regular size_t
type. There is no need for it to be atomic since it is only touched
under the protection of the priv->buffer_mutex.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
The TPM burstcount and status commands are supposed to return very
quickly [2][3]. This patch further reduces the TPM poll sleep time to usecs
in get_burstcount() and wait_for_tpm_stat() by calling usleep_range()
directly.
After this change, performance on a system[1] with a TPM 1.2 with an 8 byte
burstcount for 1000 extends improved from ~10.7 sec to ~7 sec.
[1] All tests are performed on an x86 based, locked down, single purpose
closed system. It has Infineon TPM 1.2 using LPC Bus.
[2] From the TCG Specification "TCG PC Client Specific TPM Interface
Specification (TIS), Family 1.2":
"NOTE : It takes roughly 330 ns per byte transfer on LPC. 256 bytes would
take 84 us, which is a long time to stall the CPU. Chipsets may not be
designed to post this much data to LPC; therefore, the CPU itself is
stalled for much of this time. Sending 1 kB would take 350 μs. Therefore,
even if the TPM_STS_x.burstCount field is a high value, software SHOULD
be interruptible during this period."
[3] From the TCG Specification 2.0, "TCG PC Client Platform TPM Profile
(PTP) Specification":
"It takes roughly 330 ns per byte transfer on LPC. 256 bytes would take
84 us. Chipsets may not be designed to post this much data to LPC;
therefore, the CPU itself is stalled for much of this time. Sending 1 kB
would take 350 us. Therefore, even if the TPM_STS_x.burstCount field is a
high value, software should be interruptible during this period. For SPI,
assuming 20MHz clock and 64-byte transfers, it would take about 120 usec
to move 256B of data. Sending 1kB would take about 500 usec. If the
transactions are done using 4 bytes at a time, then it would take about
1 msec. to transfer 1kB of data."
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Jay Freyensee <why2jjj.linux@gmail.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Use kmemdup rather than duplicating its implementation.
Signed-off-by: Ji-Hun Kim <ji_hun.kim@samsung.com>
Reviewed-by: James Morris <james.morris@microsoft.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
|
|
Use kmemdup rather than duplicating its implementation.
Signed-off-by: Ji-Hun Kim <ji_hun.kim@samsung.com>
Reviewed-by: James Morris <james.morris@microsoft.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
If load context command returns with TPM2_RC_HANDLE or TPM2_RC_REFERENCE_H0
then we have use after free in line 114 and double free in 117.
Fixes: 4d57856a21ed2 ("tpm2: add session handle context saving and restoring to the space code")
Cc: stable@vger.kernel.org
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off--by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
tpm_try_transmit currently checks TPM status every 5 msecs between
send and recv. It does so in a loop for the maximum timeout as defined
in the TPM Interface Specification. However, the TPM may return before
5 msecs. Thus the polling interval for each iteration can be reduced,
which improves overall performance. This patch changes the polling sleep
time from 5 msecs to 1 msec.
Additionally, this patch renames TPM_POLL_SLEEP to TPM_TIMEOUT_POLL and
moves it to tpm.h as an enum value.
After this change, performance on a system[1] with a TPM 1.2 with an 8 byte
burstcount for 1000 extends improved from ~14 sec to ~10.7 sec.
[1] All tests are performed on an x86 based, locked down, single purpose
closed system. It has Infineon TPM 1.2 using LPC Bus.
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Acked-by: Jay Freyensee <why2jjj.linux@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
For certain tpm chips releasing locality can take long enough that a
subsequent call to request_locality will see the locality as being active
when the access register is read in check_locality. So check that the
locality has been released before returning from release_locality.
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Reported-by: Laurent Bigonville <bigon@debian.org>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Laurent Bigonville <bigon@debian.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
In crb_map_io() function, __crb_request_locality() is called prior
to crb_cmd_ready(), but if one of the consecutive function fails
the flow bails out instead of trying to relinquish locality.
This patch adds goto jump to __crb_relinquish_locality() on the error path.
Fixes: 888d867df441 (tpm: cmd_ready command can be issued only after granting locality)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Fix spelling mistake, rename ST33ZP24_TISREGISTER_UKNOWN to
ST33ZP24_TISREGISTER_UNKNOWN
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Reduce the size of tpm.h by moving eventlog declarations to a separate
header.
Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|