| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
pll14xx_calc_rate() output the fout clock not the fvco clock
The relation of fvco and fout is:
fout = fvco / (1 << sdiv)
So use correct naming for the clock.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/1703068389-6130-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
Since commit b09c68dc57c9 ("clk: imx: pll14xx: Support dynamic rates"),
the driver has the ability to dynamically compute PLL parameters to
approximate the requested rates. This is not always used, because the
logic is as follows:
- Check if the target rate is hardcoded in the frequency table
- Check if varying only kdiv is possible, so switch over is glitch free
- Compute rate dynamically by iterating over pdiv range
If we skip the frequency table for the 1443x PLL, we find that the
computed values differ to the hardcoded ones. This can be valid if the
hardcoded values guarantee for example an earlier lock-in or if the
divisors are chosen, so that other important rates are more likely to
be reached glitch-free.
For rates (393216000 and 361267200, this doesn't seem to be the case:
They are only approximated by existing parameters (393215995 and
361267196 Hz, respectively) and they aren't reachable glitch-free from
other hardcoded frequencies. Dropping them from the table allows us
to lock-in to these frequencies exactly.
This is immediately noticeable because they are the assigned-clock-rates
for IMX8MN_AUDIO_PLL1 and IMX8MN_AUDIO_PLL2, respectively and a look
into clk_summary so far showed that they were a few Hz short of the target:
imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out 0 0 0 361267196 0 0 50000 N
audio_pll1_out 1 1 0 393215995 0 0 50000 Y
and afterwards:
imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out 0 0 0 361267200 0 0 50000 N
audio_pll1_out 1 1 0 393216000 0 0 50000 Y
This change is equivalent to adding following hardcoded values:
/* rate mdiv pdiv sdiv kdiv */
PLL_1443X_RATE(393216000, 655, 5, 3, 23593),
PLL_1443X_RATE(361267200, 497, 33, 0, -16882),
Fixes: 053a4ffe2988 ("clk: imx: imx8mm: fix audio pll setting")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230807084744.1184791-2-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
The PLL14xx hardware can be found on i.MX8M{M,N,P} SoCs and always come
with a 6-bit pre-divider. Neither the reference manuals nor the
datasheets of these SoCs do mention any restrictions. Furthermore the
current code doesn't respect the restrictions from the comment too.
Therefore drop the restriction and align the max pre-divider (pdiv)
value to 63 to get more accurate frequencies.
Fixes: b09c68dc57c9 ("clk: imx: pll14xx: Support dynamic rates")
Cc: stable@vger.kernel.org
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20230807084744.1184791-1-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
kdiv is a signed 16 bit value in the DEV_CTL1 register. Commit
53990cf9d5b4 ("clk: imx: pll14xx: consolidate rate calculation") changed
the kdiv variable from a short int to just int. When the value read from
the DIV_CTL1 register is assigned directly to an int the sign of the value
is lost resulting in incorrect results when the value is negative. Adding
a s16 cast to the register value fixes the issue.
Fixes: 53990cf9d5b4 ("clk: imx: pll14xx: consolidate rate calculation")
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Link: https://lore.kernel.org/r/20221210203835.9714-1-kgroeneveld@lenbrook.com
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The PLL146x is used to implement SYS_PLL3 on i.MX8MP and can be used
to drive UARTn_ROOT clock. By setting the PLL3 to 320 MHz or 640 MHz,
the PLL3 output can be divided down to supply UARTn_ROOT clock with
precise 64 MHz, which divided down further by 16x oversampling factor
used by the i.MX UART core yields 4 Mbdps baud base for the UART IP.
This is useful e.g. for BCM bluetooth chips, which can operate up to
4 Mbdps.
Add 320 MHz and 640 MHz entries so the PLL can be configured accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221031204838.195292-1-marex@denx.de
|
|
The pll1443x PLL so far only supports rates from a rate table passed
during initialization. Calculating PLL settings dynamically helps audio
applications to get their desired rates, so support for this is added
in this patch.
The strategy to get to the PLL setting for a rate is:
- First try to only adjust kdiv which specifies the fractional part of the PLL.
This setting can be changed without glitches on the output and is therefore
preferred
- When that isn't possible then the rate table is searched for suitable rates,
so for standard rates the same settings are used as without this patch
- As a last resort the best settings are calculated dynamically
The code in this patch is based on patches from Adrian Alonso <adrian.alonso@nxp.com>
and Mads Bligaard Nielsen <bli@bang-olufsen.dk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-9-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
Print all messages from within the pll14xx driver with a common
prefix using pr_fmt. No need to print function names anymore, so
drop them from the messages.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-8-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
clk_pll14xx_round_rate() returns the lowest rate by indexing into
the rate table with the variable i. i is actually pll->rate_count
as this is the value we come out of the loop with. Use pll->rate_count
explicitly to make it a bit more clear what is being done. While at
it fix a typo in the comment. No functional change.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-7-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
In clk_pll1443x_set_rate() 'tmp' is used for the content of different
registers which makes it a bit hard to follow. Use different variables
named after the registers to make it clearer. No functional change
intended.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-6-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
The PLL driver has support for two different PLLs: The pll1416x and
the pll1443x. The latter has support for an additional kdiv value.
recalc_rate can be the same calculation when kdiv is assumed to be zero
for the PLL which doesn't support that value.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-5-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
Linux has these marvelous FIELD_GET/FIELD_PREP macros for easy access
to bitfields in registers. Use them and remove the now unused *_SHIFT
defines.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-4-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
The code tries to mask the bits in SDIV_MASK from 'tmp'. SDIV_MASK
already contains the shifted value, so shifting it again is wrong.
No functional change though as SDIV_SHIFT is zero.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-3-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
The driver has defines for the registers, but they are mostly unused.
Use the defines consistently throughout the driver. While at it rename
DIV_CTL to DIV_CTL0 because that's the name in the reference manual.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-2-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
A semicolon is not needed after a switch statement.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
It is better to explicitly include the required header file rather
then get it through some recursive include.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There are more and more requirements of building SoC specific drivers
as modules, add support for building i.MX common clock driver as module
to meet the requirement.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
In order to allow runtime PM, the device needs to be passed on
to the register function. Audiomix clock controller, used on
i.MX8MP and future platforms, registers a pll14xx and has runtime
PM support.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
When pll type is invalid, ONLY output error message is NOT enough,
should return error immediately.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add new frequency entries to pll1443x table to meet different
display settings requirement.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
'clk-freescale' and 'clk-qoriq' into clk-next
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Fixes for clk controllers on qcom msm8998 SoCs
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Adjust composite clk to new way of describing clk parents
- Add a driver for BCLK of Freescale SAI cores
* clk-imx: (32 commits)
clk: imx: Add support for i.MX8MP clock driver
dt-bindings: imx: Add clock binding doc for i.MX8MP
clk: imx: gate4: Switch imx_clk_gate4_flags() to clk_hw based API
clk: imx: imx8mq: Switch to clk_hw based API
clk: imx: imx8mm: Switch to clk_hw based API
clk: imx: imx8mn: Switch to clk_hw based API
clk: imx: Remove __init for imx_obtain_fixed_clk_hw() API
clk: imx: gate3: Switch to clk_hw based API
clk: imx: add hw API imx_clk_hw_mux2_flags
clk: imx: add imx_unregister_hw_clocks
clk: imx: clk-composite-8m: Switch to clk_hw based API
clk: imx: clk-pll14xx: Switch to clk_hw based API
clk: imx7up: Rename the clks to hws
clk: imx: Rename the imx_clk_divider_gate to imply it's clk_hw based
clk: imx: Rename the imx_clk_pfdv2 to imply it's clk_hw based
clk: imx: Rename the imx_clk_pllv4 to imply it's clk_hw based
clk: imx: Rename sccg and frac pll register to suggest clk_hw
clk: imx: imx7ulp composite: Rename to show is clk_hw based
clk: imx: pllv2: Switch to clk_hw based API
clk: imx: pllv1: Switch to clk_hw based API
...
* clk-ti:
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
clk: ti: dra7: fix parent for gmac_clkctrl
clk: ti: dra7: add vpe clkctrl data
clk: ti: dra7: add cam clkctrl data
dt-bindings: clock: Move ti-dra7-atl.h to dt-bindings/clock
* clk-xilinx:
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
* clk-nvidia:
clk: tegra20/30: Explicitly set parent clock for Video Decoder
clk: tegra20/30: Don't pre-initialize displays parent clock
clk: tegra: divider: Check UART's divider enable-bit state on rate's recalculation
clk: tegra: clk-dfll: Remove call to pm_runtime_irq_safe()
clk: tegra: Mark fuse clock as critical
* clk-qcom: (35 commits)
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: qcom: Add ipq6018 Global Clock Controller support
clk: qcom: Add DT bindings for ipq6018 gcc clock controller
clk: qcom: gcc-msm8996: Fix parent for CLKREF clocks
clk: qcom: rpmh: Add IPA clock for SC7180
clk: qcom: rpmh: skip undefined clocks when registering
clk: qcom: Add video clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Video clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM VIDEOCC clock bindings
clk: qcom: Add graphics clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Graphics clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM GPUCC clock bindings
clk: qcom: apcs-msm8916: use clk_parent_data to specify the parent
clk: qcom: Add display clock controller driver for SC7180
dt-bindings: clock: Introduce QCOM sc7180 display clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM DISPCC clock bindings
clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration
clk: qcom: alpha-pll: Remove useless read from set rate
...
* clk-freescale:
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
* clk-qoriq:
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
|
|
Switch the imx_clk_pll14xx function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The usage of readl_poll_timeout is wrong, the 3rd parameter(cond)
should be "val & LOCK_STATUS" not "val & LOCK_TIMEOUT_US",
It is not check whether the pll locked, LOCK_STATUS reflects the mask,
not LOCK_TIMEOUT_US.
Fixes: 8646d4dcc7fb ("clk: imx: Add PLLs driver for imx8mm soc")
Cc: <stable@vger.kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
DRAM frequency switches are executed in firmware and can change the
configuration of the DRAM PLL outside linux. Mark these CLKs with
CLK_GET_RATE_NOCACHE so we always read back the PLL config registers and
recalculate rates.
In current DRAM frequency tables on 8mm/8mn only the maximum frequency
uses the PLL so it's always configured in the same way. However reading
back the PLL configuration is the correct behavior and allows additional
setpoints in the future.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix sparse warnings:
drivers/clk/imx/clk-pll14xx.c:44:37:
warning: symbol 'imx_pll1416x_tbl' was not declared. Should it be static?
drivers/clk/imx/clk-pll14xx.c:57:37:
warning: symbol 'imx_pll1443x_tbl' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use common 1413X/1416X PLL clock structure to save a lot
of duplicated code on i.MX8MN clock driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Many i.MX8M SoCs use same 1443X/1416X PLL, such as i.MX8MM,
i.MX8MN and later i.MX8M SoCs, moving these PLL definitions
to pll14xx driver can save a lot of duplicated code on each
platform.
Meanwhile, no need to define PLL clock structure for every
module which uses same type of PLL, e.g., audio/video/dram use
1443X PLL, arm/gpu/vpu/sys use 1416X PLL, define 2 PLL clock
structure for each group is enough.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PLL14xx on imx8m can change the S and K parameter without requiring
a reset and relock of the whole PLL.
Fix clk_pll144xx_mp_change register reading and use it for pll1443 as
well since no reset+relock is required on K changes either.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 8646d4dcc7fb ("clk: imx: Add PLLs driver for imx8mm soc")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
When registering the PLL, unbypass the PLL.
The PLL has two bypass control bit, BYPASS and EXT_BYPASS.
we will expose EXT_BYPASS to clk driver for mux usage, and keep
BYPASS inside pll14xx usage. The PLL has a restriction that
when M/P change, need to RESET/BYPASS pll to avoid glitch, so
we could not expose BYPASS.
To make it easy for clk driver usage, unbypass PLL which does
not hurt current function.
Fixes: 8646d4dcc7fb ("clk: imx: Add PLLs driver for imx8mm soc")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-3-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
According to PLL1443XA and PLL1416X spec,
"When BYPASS is 0 and RESETB is changed from 0 to 1, FOUT starts to
output unstable clock until lock time passes. PLL1416X/PLL1443XA may
generate a glitch at FOUT."
So set BYPASS when RESETB is changed from 0 to 1 to avoid glitch.
In the end of set rate, BYPASS will be cleared.
When prepare clock, also need to take care to avoid glitch. So
we also follow Spec to set BYPASS before RESETB changed from 0 to 1.
And add a check if the RESETB is already 0, directly return 0;
Fixes: 8646d4dcc7fb ("clk: imx: Add PLLs driver for imx8mm soc")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-2-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
'clk-imx' into clk-next
- Qualcomm QCS404 CDSP clk support
- Qualcomm QCS404 Turing clk support
- Mediatek MT8183 clock support
- Mediatek MT8516 clock support
- Milbeaut M10V clk controller support
* clk-renesas:
clk: renesas: rcar-gen3: Remove unused variable
clk: renesas: rcar-gen3: Fix cpg_sd_clock_round_rate() return value
clk: renesas: r8a77980: Fix RPC-IF module clock's parent
clk: renesas: rcar-gen3: Rename DRIF clocks
clk: renesas: rcar-gen3: Correct parent clock of Audio-DMAC
clk: renesas: rcar-gen3: Correct parent clock of SYS-DMAC
clk: renesas: rcar-gen3: Correct parent clock of HS-USB
clk: renesas: rcar-gen3: Correct parent clock of EHCI/OHCI
clk: renesas: r8a774c0: Add Z2 clock
clk: renesas: r8a77990: Add Z2 clock
clk: renesas: rcar-gen3: Support Z and Z2 clocks with high frequency parents
math64: New DIV64_U64_ROUND_CLOSEST helper
clk: renesas: rcar-gen3: Remove CLK_TYPE_GEN3_Z2
clk: renesas: rcar-gen3: Parameterise Z and Z2 clock offset
clk: renesas: rcar-gen3: Parameterise Z and Z2 clock fixed divisor
clk: renesas: r9a06g032: Add missing PCI USB clock
clk: renesas: r7s9210: Always use readl()
clk: renesas: rcar-gen3: Pass name/offset to cpg_sd_clk_register()
* clk-qcom:
clk: qcom: Skip halt checks on gcc_pcie_0_pipe_clk for 8998
clk: qcom: Add QCS404 TuringCC
clk: qcom: branch: Add AON clock ops
dt-bindings: clock: Introduce Qualcomm Turing Clock controller
clk: qcom: gcc-qcs404: Add CDSP related clocks and resets
* clk-mtk:
clk: mediatek: add clock driver for MT8516
dt-bindings: mediatek: apmixedsys: add support for MT8516
dt-bindings: mediatek: infracfg: add support for MT8516
dt-bindings: mediatek: topckgen: add support for MT8516
clk: mediatek: Allow changing PLL rate when it is off
clk: mediatek: Add MT8183 clock support
clk: mediatek: Add configurable pcw_chg_reg to mtk_pll_data
clk: mediatek: Add dt-bindings for MT8183 clocks
dt-bindings: ARM: Mediatek: Document bindings for MT8183
clk: mediatek: Add configurable pcwibits and fmin to mtk_pll_data
clk: mediatek: Add new clkmux register API
clk: mediatek: Disable tuner_en before change PLL rate
* clk-milbeaut:
clock: milbeaut: Add Milbeaut M10V clock controller
dt-bindings: clock: milbeaut: add Milbeaut clock description
* clk-imx:
clk: imx: correct pfdv2 gate_bit/vld_bit operations
clk: imx: clk-pllv3: mark expected switch fall-throughs
clk: imx8mq: Add dsi_ipg_div
clk: imx: pllv4: add fractional-N pll support
clk: imx: keep uart clock on during system boot
clk: imx: correct i.MX7D AV PLL num/denom offset
clk: imx6sll: Fix mispelling uart4_serial as serail
clk: imx: pll14xx: drop unused variable
clk: imx: rename clk-imx51-imx53.c to clk-imx5.c
clk: imx5: Fix i.MX50 ESDHC clock registers
clk: imx5: Fix i.MX50 mainbus clock registers
clk: imx: Remove unused imx_get_clk_hw_fixed
dt-bindings: clock: imx7ulp: remove SNVS clock
clk: imx7ulp: remove snvs clock
|
|
It does not make sense to only get value from pll->base and assign
to a local variable when recalc_rate.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Code which initializes the "clk_init_data.ops" checks pll->rate_table
before that field is ever assigned to so it always picks
"clk_pll1416x_min_ops".
This breaks dynamic rate rounding for features such as cpufreq.
Fix by checking pll_clk->rate_table instead, here pll_clk refers to
the constant initialization data coming from per-soc clk driver.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 8646d4dcc7fb ("clk: imx: Add PLLs driver for imx8mm soc")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
New PLLs are introduced on i.MX8M Mini SOC.
PLL1416X is Integer PLL, PLL1443X is a Frac PLL.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
