summaryrefslogtreecommitdiff
path: root/drivers/fsi/fsi-master-aspeed.c
AgeCommit message (Collapse)AuthorFilesLines
2019-11-08fsi: aspeed: Fix OPB0 byte order register valuesAndrew Jeffery1-3/+3
The data byte order selection registers in the APB2OPB primarily expose some internal plumbing necessary to get correct write accesses onto the OPB. OPB write cycles require "data mirroring" across the 32-bit data bus to support variable data width slaves that don't implement "byte enables". For slaves that do implement byte enables the master can signal which bytes on the data bus the slave should consider valid. The data mirroring behaviour is specified by the following table: +-----------------+----------+-----------------------------------+ | | | 32-bit Data Bus | +---------+-------+----------+---------+---------+-------+-------+ | | | | | | | | | ABus | Mn_BE | Request | Dbus | Dbus | Dbus | Dbus | | (30:31) | (0:3) | Transfer | 0:7 | 8:15 | 16:23 | 24:31 | | | | Size | byte0 | byte1 | byte2 | byte3 | +---------+-------+----------+---------+---------+-------+-------+ | 00 | 1111 | fullword | byte0 | byte1 | byte2 | byte3 | +---------+-------+----------+---------+---------+-------+-------+ | 00 | 1110 | halfword | byte0 | byte1 | byte2 | | +---------+-------+----------+---------+---------+-------+-------+ | 01 | 0111 | byte | _byte1_ | byte1 | byte2 | byte3 | +---------+-------+----------+---------+---------+-------+-------+ | 00 | 1100 | halfword | byte0 | byte1 | | | +---------+-------+----------+---------+---------+-------+-------+ | 01 | 0110 | byte | _byte1_ | byte1 | byte2 | | +---------+-------+----------+---------+---------+-------+-------+ | 10 | 0011 | halfword | _byte2_ | _byte3_ | byte2 | byte3 | +---------+-------+----------+---------+---------+-------+-------+ | 00 | 1000 | byte | byte0 | | | | +---------+-------+----------+---------+---------+-------+-------+ | 01 | 0100 | byte | _byte1_ | byte1 | | | +---------+-------+----------+---------+---------+-------+-------+ | 10 | 0010 | byte | _byte2_ | | byte2 | | +---------+-------+----------+---------+---------+-------+-------+ | 11 | 0001 | byte | _byte3_ | _byte3_ | | byte3 | +---------+-------+----------+---------+---------+-------+-------+ Mirrored data values are highlighted by underscores in the Dbus columns. The values in the ABus and Request Transfer Size columns correspond to values in the field names listed in the write data order select register descriptions. Similar configuration registers are exposed for reads which enables the secondary purpose of configuring hardware endian conversions. It appears the data bus byte order is switched around in hardware so set the registers such that we can access the correct values for all widths. The values were determined by experimentation on hardware against fixed CFAM register values to configure the read data order, then in combination with the table above and the register layout documentation in the AST2600 datasheet performing write/read cycles to configure the write data order registers. Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Alistair Popple <alistair@popple.id.au> Link: https://lore.kernel.org/r/20191108051945.7109-12-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-08fsi: aspeed: Add trace pointsJoel Stanley1-0/+22
These trace points help with debugging the FSI master. They show the low level reads, writes and error states of the master. Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20191108051945.7109-11-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-08fsi: Add ast2600 master driverJoel Stanley1-0/+522
The ast2600 BMC has a pair of FSI masters in it, behind an AHB to OPB bridge. The master driver supports reads and writes of full words, half word and byte accesses to remote CFAMs. It can perform very basic error recovery through resetting of the FSI port when an error is detected, and the issuing of breaks and terms. Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Alistair Popple <alistair@popple.id.au> -- v2: - remove debugging - squash in fixes Link: https://lore.kernel.org/r/20191108051945.7109-10-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>