Age | Commit message (Collapse) | Author | Files | Lines |
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have a lot of code refactoring using common helpers and ended up
removing more lines then we're adding this release cycle.
Nothing really stands out, just small updates all over the place.
Core GPIOLIB updates:
- wake-up poll() in user-space on device unbind
- improve fwnode usage
- interrupt domain handling improvements
- correctly handle the ngpios property in gpio-mmio
Driver cleanups:
- remove unneeded calls to platform_set_drvdata() all around the
place
- remove unneeded of_match_ptr() expansions whenever a driver depends
on CONFIG_OF
- remove redundant calls to dev_err_probe() from gpio-omap and
gpio-davinci
Driver improvements:
- use autopointers and guards from cleanup.h in gpio-sim
- shrink code in gpio-sim using some common helpers
- convert the idio family of drivers to using gpio-regmap
- convert gpio-ws16c48 to using gpio-regmap
- use devres to simplify code in gpio-pisosr and gpio-mxc
- update gpio-sifive: support IRQ wake, improve interrupt handling,
allow building as module
- make gpio-ge and gpio-bcm-kona OF-independent (plus some minor
tweaks)
- add support for new models in gpio-pca953x and gpio-ds4520
- add runtime PM support to gpio-mxc
- fix a build warning in gpio-mxs
- add support for adding pin ranges to gpio-mlxbf3
- add counter/timer support to gpio-104-dio-48e
- switch to dynamic GPIO base allocation in gpio-vf610
- minor oneliners here and there
Device-tree bindings updates:
- enable the gpio-line-names property in snps,dw-apb and STMPE GPIO
- document new models in fsl-imx-gpio, ds4520 and pca95xx
- convert the bindings for brcm,kona-gpio to YAML"
* tag 'gpio-updates-for-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (94 commits)
gpio: pca953x: add support for TCA9538
dt-bindings: gpio: pca95xx: document new tca9538 chip
gpio: pca953x: Use i2c_get_match_data()
gpio: mlxbf3: use capital "OR" for multiple licenses in SPDX
gpio: pcf857x: Extend match data support for OF tables
gpio: vf610: switch to dynamic allocat GPIO base
gpiolib: provide and use gpiod_line_state_notify()
gpio: cdev: wake up lineevent poll() on device unbind
gpio: cdev: wake up linereq poll() on device unbind
gpio: cdev: wake up chardev poll() on device unbind
gpiolib: add a second blocking notifier to struct gpio_device
gpio: cdev: open-code to_gpio_chardev_data()
gpiolib: rename the gpio_device notifier
gpio: mlxbf3: Support add_pin_ranges()
gpio: mxc: Use helper function devm_clk_get_optional_enabled()
gpio: pca9570: fix kerneldoc
gpio: sim: simplify code with cleanup helpers
gpio: sim: replace memmove() + strstrip() with skip_spaces() + strim()
gpio: sim: simplify gpio_sim_device_config_live_store()
gpio: mxc: release the parent IRQ in runtime suspend
...
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Convert drivers to use the ->remove_new() callback
- Propagate the removable attribute for the card's device
MMC host:
- Convert drivers to use the ->remove_new() callback
- atmel-mci: Convert to gpio descriptors and cleanup the code
- davinci: Make SDIO irq truly optional
- renesas_sdhi: Register irqs before registering controller
- sdhci: Simplify the sdhci_pltfm_* interface a bit
- sdhci-esdhc-imx: Improve support for the 1.8V errata
- sdhci-of-at91: Add support for the microchip sam9x7 variant
- sdhci-of-dwcmshc: Add support for runtime PM
- sdhci-pci-o2micro: Add support for the new Bayhub GG8 variant
- sdhci-sprd: Add support for SD high-speed mode tuning
- uniphier-sd: Register irqs before registering controller"
* tag 'mmc-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (108 commits)
mmc: atmel-mci: Move card detect gpio polarity quirk to gpiolib
mmc: atmel-mci: move atmel MCI header file
mmc: atmel-mci: Convert to gpio descriptors
mmc: sdhci-sprd: Add SD HS mode online tuning
mmc: core: Add host specific tuning support for SD HS mode
mmc: sdhci-of-dwcmshc: Add runtime PM operations
mmc: sdhci-of-dwcmshc: Add error handling in dwcmshc_resume
mmc: sdhci-esdhc-imx: improve ESDHC_FLAG_ERR010450
mmc: sdhci-pltfm: Rename sdhci_pltfm_register()
mmc: sdhci-pltfm: Remove sdhci_pltfm_unregister()
mmc: sdhci-st: Use sdhci_pltfm_remove()
mmc: sdhci-pxav2: Use sdhci_pltfm_remove()
mmc: sdhci-of-sparx5: Use sdhci_pltfm_remove()
mmc: sdhci-of-hlwd: Use sdhci_pltfm_remove()
mmc: sdhci-of-esdhc: Use sdhci_pltfm_remove()
mmc: sdhci-of-at91: Use sdhci_pltfm_remove()
mmc: sdhci-of-arasan: Use sdhci_pltfm_remove()
mmc: sdhci-iproc: Use sdhci_pltfm_remove()
mmc: sdhci_f_sdh30: Use sdhci_pltfm_remove()
mmc: sdhci-dove: Use sdhci_pltfm_remove()
...
|
|
The polarity of the card detection gpio is handled by the "cd-inverted"
property in the device tree. Move this inversion logic to gpiolib to avoid
reading the gpio raw value.
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230825095157.76073-4-balamanikandan.gunasundar@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The TCA9538 is an 8 bit version of the already supported TCA9539.
This chip also has interrupt support.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Replace device_get_match_data() and id lookup for retrieving match data
by i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Associate the swnode of the GPIO device's (which is the interrupt
controller here) with the irq domain. Otherwise the interrupt-controller
device attribute is a no-op.
Fixes: cb8c474e79be ("gpio: sim: new testing module")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
If a GPIO simulator device is unbound with interrupts still requested,
we will hit a use-after-free issue in __irq_domain_deactivate_irq(). The
owner of the irq domain must dispose of all mappings before destroying
the domain object.
Fixes: cb8c474e79be ("gpio: sim: new testing module")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The driver has OF match table, but still it uses an ID lookup table for
retrieving match data. Currently, the driver is working on the
assumption that an I2C device registered via OF will always match a
legacy I2C device ID. Extend match data support for OF tables by using
i2c_get_match_data() instead of the ID lookup for both OF/ID matches by
making similar OF/ID tables.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
gpiolib want to get completely rid of static gpiobase allocation,
so switch to dynamic allocat GPIO base, also can avoid warning
message:
[ 1.529974] gpio gpiochip0: Static allocation of GPIO base
is deprecated, use dynamic allocation.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Wrap the calls to blocking_notifier_call_chain() for the line state
notifier with a helper that allows us to use fewer lines of code and
simpler syntax.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add a notifier block to the lineevent_state structure and register it
with the gpio_device's device notifier. Upon reception of an event, wake
up the wait queue so that the user-space be forced out of poll() and
need to go into a new system call which will then fail due to the chip
being gone.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
|
|
Add a notifier block to the linereq structure and register it with the
gpio_device's device notifier. Upon reception of an event, wake up the
wait queue so that the user-space be forced out of poll() and need to go
into a new system call which will then fail due to the chip being gone.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
|
|
Add a notifier block to the gpio_chardev_data structure and register it
with the gpio_device's device notifier. Upon reception of an event, wake
up the wait queue so that the user-space be forced out of poll() and need
to go into a new system call which will then fail due to the chip being
gone.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
|
|
Add a new blocking notifier to struct gpio_device and use it to notify
subscribers about the GPIO device being unregistered from the device
model.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
|
|
This function is a wrapper around container_of(). It's used only once and
we will have a second notifier soon, so instead of having two flavors of
this helper, let's just open-code where needed.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
|
|
Change the generic "notifier" name to "line_state_notifier" in order to
reflect its purpose in preparation for adding a second notifier which
will be used to notify wait queues about device unregistering.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
|
|
Support add_pin_ranges() so that pinctrl_gpio_request() can be called.
The GPIO value is not modified when the user runs the "gpioset" tool.
This is because when gpiochip_generic_request is invoked by the gpio-mlxbf3
driver, "pin_ranges" is empty so it skips "pinctrl_gpio_request()".
pinctrl_gpio_request() is essential in the code flow because it changes the
mux value so that software has control over modifying the GPIO value.
Adding add_pin_ranges() creates a dependency on the pinctrl-mlxbf3.c driver.
Fixes: cd33f216d24 ("gpio: mlxbf3: Add gpio driver support")
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for
prepared and enabled clocks"), devm_clk_get_optional() and
clk_prepare_enable() can now be replaced by
devm_clk_get_optional_enabled() when the driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover,
it is no longer necessary to unprepare and disable the clocks explicitly.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
While renaming one of the fields in the driver data struct, the kerneldoc
was not updated which apparently angers the test robot now.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308171538.nKKUOtbg-lkp@intel.com/
Fixes: a3f7c1d6ddcb ("gpio: pca9570: rename platform_data to chip_data")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Use macros defined in linux/cleanup.h to automate resource lifetime
control in gpio-sim.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
After we remove a GPIO chip that still has some requested descriptors,
gpiod_free_commit() will fail and we will never put the references to the
GPIO device and the owning module in gpiod_free().
Rework this function to:
- not warn on desc == NULL as this is a use-case on which most free
functions silently return
- put the references to desc->gdev and desc->gdev->owner unconditionally
so that the release callback actually gets called when the remaining
references are dropped by external GPIO users
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It seems that sysfs interface implicitly relied on the gpiod_free() to
unexport the line. This is logically incorrect as core gpiolib should
not deal with sysfs so instead of restoring it, let's call
gpiod_unexport() from sysfs code.
Fixes: b0ce9ce408b6 ("gpiolib: Do not unexport GPIO on freeing")
Reported-by: Marek Behún <kabel@kernel.org>
Closes: https://lore.kernel.org/r/20230808102828.4a9eac09@dellmb
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Marek Behún <kabel@kernel.org>
[Bartosz: tweaked the commit message]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Turns out we can avoid the memmove() by using skip_spaces() and strim().
We did that in gpio-consumer, let's do it in gpio-sim.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Simplify the logic when checking the current live value against the user
input.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The WinSystems WS16C48 I/O address region spans offsets 0x0 through 0xA,
which is a total of 11 bytes. Fix the WS16C48_EXTENT define to the
correct value of 11 so that access to necessary device registers is
properly requested in the ws16c48_probe() callback by the
devm_request_region() function call.
Fixes: 2c05a0f29f41 ("gpio: ws16c48: Implement and utilize register structures")
Cc: stable@vger.kernel.org
Cc: Paul Demetrotion <pdemetrotion@winsystems.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Release the parent interrupt request during runtime suspend, allowing
the parent interrupt controller to enter runtime suspend if there are
no active users.
This change may not have a visible impact if the parent controller is
the GIC, but it can enable significant power savings for parent IRQ
controllers like IRQSteer inside a subsystem on i.MX8 SoCs. Releasing
the parent IRQ provides an opportunity for the subsystem to enter suspend
states if there are no active users.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
'devid' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
gpio-mxs.c:274:16: error: cast to smaller integer type 'enum mxs_gpio_id' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use of macro ARRAY_SIZE to calculate array size minimizes
the redundant code and improves code reusability.
This fixes warnings reported by Coccinelle:
drivers/gpio/gpio-imx-scu.c:106:32-33: WARNING: Use ARRAY_SIZE
Signed-off-by: Rajeshwar R Shinde <coolrrsh@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
The WinSystems WS16C48 provides the following registers:
Offset 0x0-0x5: Port 0-5 I/O
Offset 0x6: Int_Pending
Offset 0x7: Page/Lock
Offset 0x8-0xA (Page 1): Pol_0-Pol_2
Offset 0x8-0xA (Page 2): Enab_0-Enab_2
Offset 0x8-0xA (Page 3): Int_ID0-Int_ID2
Port 0-5 I/O provides access to 48 lines of digital I/O across six
registers, each bit position corresponding to the respective line.
Writing a 1 to a respective bit position causes that output pin to sink
current, while writing a 0 to the same bit position causes that output
pin to go to a high-impedance state and allows it to be used an input.
Reads on a port report the inverted state (0 = high, 1 = low) of an I/O
pin when used in input mode. Interrupts are supported on Port 0-2.
Int_Pending is a read-only register that reports the combined state of
the INT_ID0 through INT_ID2 registers; an interrupt pending is indicated
when any of the low three bits are set.
The Page/Lock register provides the following bits:
Bit 0-5: Port 0-5 I/O Lock
Bit 6-7: Page 0-3 Selection
For Bits 0-5, writing a 1 to a respective bit position locks the output
state of the corresponding I/O port. Writing the page number to Bits 6-7
selects that respective register page for use.
Pol_0-Pol_2 are accessible when Page 1 is selected. Writing a 1 to a
respective bit position selects the rising edge detection interrupts for
that input line, while writing a 0 to the same bit position selects the
falling edge detection interrupts.
Enab_0-Enab_2 are accessible when Page 2 is selected. Writing a 1 to a
respective bit position enables interrupts for that input line, while
writing a 0 to that same bit position clears and disables interrupts for
that input line.
Int_ID0-Int_ID2 are accessible when Page 3 is selected. A respective bit
when read as a 1 indicates that an edge of the polarity set in the
corresponding polarity register was detected for the corresponding input
line. Writing any value to this register clears all pending interrupts
for the register.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/f59de81e80f7198bcfa9a15615c459c38b5d0e08.1680708357.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
For the PCIe-IDIO-24 series of devices, the following BARs are
available:
BAR[0]: memory mapped PEX8311
BAR[1]: I/O mapped PEX8311
BAR[2]: I/O mapped card registers
There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS
lines (which may be configured for either output or input). The GPIO
lines are exposed by the following card registers:
Base +0x0-0x2 (Read/Write): FET Outputs
Base +0xB (Read/Write): TTL/CMOS
Base +0x4-0x6 (Read): Isolated Inputs
Base +0x7 (Read): TTL/CMOS
In order for the device to support interrupts, the PLX PEX8311 internal
PCI wire interrupt and local interrupt input must first be enabled.
The following card registers for Change-Of-State may be used:
Base +0x8-0xA (Read): COS Status Inputs
Base +0x8-0xA (Write): COS Clear Inputs
Base +0xB (Read): COS Status TTL/CMOS
Base +0xB (Write): COS Clear TTL/CMOS
Base +0xE (Read/Write): COS Enable
The COS Enable register is used to enable/disable interrupts and
configure the interrupt levels; each bit maps to a group of eight inputs
as described below:
Bit 0: IRQ EN Rising Edge IN0-7
Bit 1: IRQ EN Rising Edge IN8-15
Bit 2: IRQ EN Rising Edge IN16-23
Bit 3: IRQ EN Rising Edge TTL0-7
Bit 4: IRQ EN Falling Edge IN0-7
Bit 5: IRQ EN Falling Edge IN8-15
Bit 6: IRQ EN Falling Edge IN16-23
Bit 7: IRQ EN Falling Edge TTL0-7
An interrupt is asserted when a change-of-state matching the interrupt
level configuration respective for a particular group of eight inputs
with enabled COS is detected.
The COS Status registers may be read to determine which inputs have
changed; if interrupts were enabled, an IRQ will be generated for the
set bits in these registers. Writing the value read from the COS Status
register back to the respective COS Clear register will clear just those
interrupts.
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
All idio-16 library consumers have migrated to the new interface
leveraging the gpio-regmap API. Legacy interface functions and code are
removed as no longer needed.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/651cff1cc3eb57b455a8048121cf6a4d4367f018.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver. Migrate the pci-idio-16 module to the new
idio-16 library interface leveraging the gpio-regmap API.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/5ba5405c64aca984d5cf3bdbdffa04c325e5a147.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver. Migrate the 104-idio-16 module to the new
idio-16 library interface leveraging the gpio-regmap API.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/1f24a1f18c9a9daa4983713e0a5b53e838d624a8.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
By leveraging the regmap API, the idio-16 library is reduced to simply a
devm_idio_16_regmap_register() function and a configuration structure
struct idio_16_regmap_config.
Legacy functions and code will be removed once all consumers have
migrated to the new idio-16 library interface.
For IDIO-16 devices we have the following IRQ registers:
Base Address +1 (Write): Clear Interrupt
Base Address +2 (Read): Enable Interrupt
Base Address +2 (Write): Disable Interrupt
An interrupt is asserted whenever a change-of-state is detected on any
of the inputs. Any write to 0x2 will disable interrupts, while any read
will enable interrupts. Interrupts are cleared by a write to 0x1.
For 104-IDIO-16 devices, there is no IRQ status register, so software
has to assume that if an interrupt is raised then it was for the
104-IDIO-16 device.
For PCI-IDIO-16 devices, there is an additional IRQ register:
Base Address +6 (Read): Interrupt Status
Interrupt status can be read from 0x6 where bit 2 set indicates that an
IRQ has been generated.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b45081958ab53dfa697f4a8b15f1bfba46718068.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
When comparing strings passed to us from configfs, we can pass the page
argument directly to sysfs_streq() and avoid manual string trimming.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here, and __maybe_unused can also be removed.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here, and __maybe_unused can also be removed.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The driver depends on CONFIG_OF, so it is not necessary to use CONFIG_OF
and of_match_ptr() here, we remove them all.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The driver depends on CONFIG_OF, so it is not necessary to use
CONFIG_OF and of_match_ptr() here, so we remove them all.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it. Hence we remove of_match_ptr().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it. Hence we remove of_match_ptr().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it. Hence we remove of_match_ptr().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here. We remove both CONFIG_OF and of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it. Hence we remove of_match_ptr().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Since commit a85a6c86c25b ("driver core: platform: Clarify that IRQ 0
is invalid"), there is no possible for platform_get_irq() to return 0.
And the return value of platform_get_irq() is more sensible
to show the error reason.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Simulated chips use a mutex for synchronization in driver callbacks so
they must not be called from interrupt context. Set the can_sleep field
of the GPIO chip to true to force users to only use threaded irqs.
Fixes: cb8c474e79be ("gpio: sim: new testing module")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|