Age | Commit message (Collapse) | Author | Files | Lines |
|
The EDID firmware loading mechanism introduced a few built-in EDIDs that
could be forced on any connector, bypassing the EDIDs it exposes.
While convenient, this limited set of EDIDs doesn't take into account
the connector type, and we can end up with an EDID that is completely
invalid for a given connector.
For example, the edid/800x600.bin file matches the following EDID:
edid-decode (hex):
00 ff ff ff ff ff ff 00 31 d8 00 00 00 00 00 00
05 16 01 03 6d 1b 14 78 ea 5e c0 a4 59 4a 98 25
20 50 54 01 00 00 45 40 01 01 01 01 01 01 01 01
01 01 01 01 01 01 a0 0f 20 00 31 58 1c 20 28 80
14 00 15 d0 10 00 00 1e 00 00 00 ff 00 4c 69 6e
75 78 20 23 30 0a 20 20 20 20 00 00 00 fd 00 3b
3d 24 26 05 00 0a 20 20 20 20 20 20 00 00 00 fc
00 4c 69 6e 75 78 20 53 56 47 41 0a 20 20 00 c2
----------------
Block 0, Base EDID:
EDID Structure Version & Revision: 1.3
Vendor & Product Identification:
Manufacturer: LNX
Model: 0
Made in: week 5 of 2012
Basic Display Parameters & Features:
Analog display
Signal Level Standard: 0.700 : 0.000 : 0.700 V p-p
Blank level equals black level
Sync: Separate Composite Serration
Maximum image size: 27 cm x 20 cm
Gamma: 2.20
DPMS levels: Standby Suspend Off
RGB color display
First detailed timing is the preferred timing
Color Characteristics:
Red : 0.6416, 0.3486
Green: 0.2919, 0.5957
Blue : 0.1474, 0.1250
White: 0.3125, 0.3281
Established Timings I & II:
DMT 0x09: 800x600 60.316541 Hz 4:3 37.879 kHz 40.000000 MHz
Standard Timings:
DMT 0x09: 800x600 60.316541 Hz 4:3 37.879 kHz 40.000000 MHz
Detailed Timing Descriptors:
DTD 1: 800x600 60.316541 Hz 4:3 37.879 kHz 40.000000 MHz (277 mm x 208 mm)
Hfront 40 Hsync 128 Hback 88 Hpol P
Vfront 1 Vsync 4 Vback 23 Vpol P
Display Product Serial Number: 'Linux #0'
Display Range Limits:
Monitor ranges (GTF): 59-61 Hz V, 36-38 kHz H, max dotclock 50 MHz
Display Product Name: 'Linux SVGA'
Checksum: 0xc2
So, an analog monitor EDID. However, if the connector was an HDMI
monitor for example, it breaks the HDMI specification that requires,
among other things, a digital display, the VIC 1 mode and an HDMI Forum
Vendor Specific Data Block in an CTA-861 extension.
We thus end up with a completely invalid EDID, which thus might confuse
HDMI-related code that could parse it.
After some discussions on IRC, we identified mainly two ways to fix
this:
- We can either create more EDIDs for each connector type to provide
a built-in EDID that matches the resolution passed in the name, and
still be a sensible EDID for that connector type;
- Or we can just prevent the EDID to be exposed to userspace if it's
built-in.
Or possibly both.
However, the conclusion was that maybe we just don't need the built-in
EDIDs at all and we should just get rid of them. So here we are.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240221092636.691701-1-mripard@kernel.org
|
|
Since the edid_firmware module parameter was moved from
drm_kms_helper.ko to drm.ko in v4.15, we've had a backwards
compatibility helper in place, with a DRM_NOTE() suggesting to migrate
to drm.edid_firmware. This was added in commit ac6c35a4d8c7 ("drm: add
backwards compatibility support for drm_kms_helper.edid_firmware").
More than five years and 30+ kernel releases later, drop the backward
compatibility.
v2: Drop the warnings too
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114151406.61230-1-jani.nikula@intel.com
|
|
We've used a temporary platform device for firmware EDID loading since
it was introduced in commit da0df92b5731 ("drm: allow loading an EDID as
firmware to override broken monitor"), but there's no explanation why.
Using a temporary device does not play well with CONFIG_FW_CACHE=y,
which caches firmware images (e.g. on suspend) so that drivers can
request firmware when the system is not ready for it, and return the
images from the cache (e.g. during resume). This works automatically for
regular devices, but obviously not for a temporarily created device.
Stop using the throwaway platform device, and use the drm device
instead.
Note that this may still be problematic for cases where the display was
plugged in during suspend, and the firmware wasn't loaded and therefore
not cached before suspend.
References: https://lore.kernel.org/r/20220727074152.43059-1-matthieu.charette@gmail.com
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2061
Reported-by: Matthieu CHARETTE <matthieu.charette@gmail.com>
Tested-by: Matthieu CHARETTE <matthieu.charette@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114111709.434979-1-jani.nikula@intel.com
|
|
Conform to device specific logging.
v2: Include [CONNECTOR:%d:%s] (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/14f3a1e55729c9157aae93fc45320d05cc4cc7bc.1666614699.git.jani.nikula@intel.com
|
|
The EDID loader is internal to drm, not for drivers.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d58a59fede286caa8766e0813f4be492a7200287.1666614699.git.jani.nikula@intel.com
|
|
There's a lot going on here, but the main thing is switching the
firmware EDID loader to use struct drm_edid. Unfortunately, it's
difficult to reasonably split to smaller pieces.
Convert the EDID loader to struct drm_edid. There's a functional change
in validation; it no longer tries to fix errors or filter invalid
blocks. It's stricter in this sense. Hopefully this will not be an
issue.
As a by-product, this change also allows HF-EEODB extended EDIDs to be
passed via override/firmware EDID.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e64267c28eca483e83c802bc06ddd149bdcdfc66.1666614699.git.jani.nikula@intel.com
|
|
Follow the usual naming convention by file name.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d6714ae737d789764bd2bdb6e7c9a5f56c99eef3.1666614699.git.jani.nikula@intel.com
|
|
Stop passing around something that's readily available in
connector->name.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/befa53a33f2ea83094027a0e88d155779ad096e1.1666614699.git.jani.nikula@intel.com
|
|
Add helper to check if a drm debug category is enabled. Convert drm core
to use it. No functional changes.
v2: Move unlikely() to drm_debug_enabled() (Eric)
v3: Keep unlikely() when combined with other conditions (Eric)
Cc: Eric Engestrom <eric@engestrom.ch>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Eric Engestrom <eric@engestrom.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001140614.26909-1-jani.nikula@intel.com
|
|
This picks up rc2 for us as well.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3, try #2:
UAPI Changes:
- Add HDR source metadata property.
- Make drm.h compile on GNU/kFreeBSD by including stdint.h
- Clarify how the userspace reviewer has to review new kernel UAPI.
- Clarify that for using new UAPI, merging to drm-next or drm-misc-next should be enough.
Cross-subsystem Changes:
- video/hdmi: Add unpack function for DRM infoframes.
- Device tree bindings:
* Updating a property for Mali Midgard GPUs
* Updating a property for STM32 DSI panel
* Adding support for FriendlyELEC HD702E 800x1280 panel
* Adding support for Evervision VGG804821 800x480 5.0" WVGA TFT panel
* Adding support for the EDT ET035012DM6 3.5" 320x240 QVGA 24-bit RGB TFT.
* Adding support for Three Five displays TFC S9700RTWV43TR-01B 800x480 panel
with resistive touch found on TI's AM335X-EVM.
* Adding support for EDT ETM0430G0DH6 480x272 panel.
- Add OSD101T2587-53TS driver with DT bindings.
- Add Samsung S6E63M0 panel driver with DT bindings.
- Add VXT VL050-8048NT-C01 800x480 panel with DT bindings.
- Dma-buf:
- Make mmap callback actually optional.
- Documentation updates.
- Fix debugfs refcount inbalance.
- Remove unused sync_dump function.
- Fix device tree bindings in drm-misc-next after a botched merge.
Core Changes:
- Add support for HDR infoframes and related EDID parsing.
- Remove prime sg_table caching, now done inside dma-buf.
- Add shiny new drm_gem_vram helpers for simple VRAM drivers;
with some fixes to the new API on top.
- Small fix to job cleanup without timeout handler.
- Documentation fixes to drm_fourcc.
- Replace lookups of drm_format with struct drm_format_info;
remove functions that become obsolete by this conversion.
- Remove double include in bridge/panel.c and some drivers.
- Remove drmP.h include from drm/edid and drm/dp.
- Fix null pointer deref in drm_fb_helper_hotplug_event().
- Remove most members from drm_fb_helper_crtc, only mode_set is kept.
- Remove race of fb helpers with userspace; only restore mode
when userspace is not master.
- Move legacy setup from drm_file.c to drm_legacy_misc.c
- Rework scheduler job destruction.
- drm/bus was removed, remove from TODO.
- Add __drm_atomic_helper_crtc_reset() to subclass crtc_state,
and convert some drivers to use it (conversion is not complete yet).
- Bump vblank timeout wait to 100 ms for atomic.
- Docbook fix for drm_hdmi_infoframe_set_hdr_metadata.
Driver Changes:
- sun4i: Use DRM_GEM_CMA_VMAP_DRIVER_OPS instead of definining manually.
- v3d: Small cleanups, adding support for compute shaders,
reservation/synchronization fixes and job management refactoring,
fixes MMU and debugfs.
- lima: Fix null pointer in irq handler on startup, set default timeout for scheduled jobs.
- stm/ltdc: Assorted fixes and adding FB modifier support.
- amdgpu: Avoid hw reset if guilty job was already signaled.
- virtio: Add seqno to fences, add trace events, use correct flags for fence allocation.
- Convert AST, bochs, mgag200, vboxvideo, hisilicon to the new drm_gem_vram API.
- sun6i_mipi_dsi: Support DSI GENERIC_SHORT_WRITE_2 transfers.
- bochs: Small fix to use PTR_RET_OR_ZERO and driver unload.
- gma500: header fixes
- cirrus: Remove unused files.
- mediatek: Fix compiler warning after merging the HDR series.
- vc4: Rework binner bo handling.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/052875a5-27ba-3832-60c2-193d950afdff@linux.intel.com
|
|
In drm_load_edid_firmware(), fwstr is allocated by kstrdup(). And fwstr
is dereferenced in the following codes. However, memory allocation
functions such as kstrdup() may fail and returns NULL. Dereferencing
this null pointer may cause the kernel go wrong. Thus we should check
this kstrdup() operation.
Further, if kstrdup() returns NULL, we should return ERR_PTR(-ENOMEM) to
the caller site.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190524023222.GA5302@zhanggen-UX430UQ
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin st fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 50 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091649.499889647@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Continue to get rid of drmP.h. Add minimal includes to build. Sort
includes while at it.
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190506095248.20874-2-jani.nikula@intel.com
|
|
Add drm_kms_helper.edid_firmware module parameter with param ops hooks
to set drm.edid_firmware instead, for backwards compatibility.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170918182003.22238-2-jani.nikula@intel.com
|
|
Make the firmware loader more generic and generally useful.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487344854-18777-2-git-send-email-jani.nikula@intel.com
|
|
Fix egregious typo in comment.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/10576.1464589598@turing-police.cc.vt.edu
|
|
The new helper returns index of the mathing string in an array. We
would use it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make generic_edid_names[] const since it's supposed to be immutable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Allow comma separated filenames in the edid_firmware parameter.
For example:
edid_firmware=eDP-1:edid/1280x480.bin,DP-2:edid/1920x1080.bin
v2: Use strsep() to simplify parsing of comma seperated string. (Matt)
Move initial bail before strdup. (Matt)
v3: Changed conditionals after while loop to make more readable (Jani)
Updated kernel-parameters.txt to reflect changes (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
[danvet: Flatten else control flow and appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Displayport compliance test 4.2.2.6 requires that a source device be capable of
detecting a corrupt EDID. The test specification states that the sink device
sets up the EDID with an invalid checksum. To do this, the sink sets up an
invalid EDID header, expecting the source device to generate the checksum and
compare it to the value stored in the last byte of the block data.
Unfortunately, the DRM EDID reading and parsing functions are actually too good
in this case; the header is fixed before the checksum is computed and thus the
test never sees the invalid checksum. This results in a failure to pass the
compliance test.
To correct this issue, when the EDID code detects that the header is invalid,
a flag is set to indicate that the EDID is corrupted. In this case, it sets
edid_corrupt flag and continues with its fix-up code. This flag is also set in
the case of a more seriously damaged header (fixup score less than the
threshold). For consistency, the edid_corrupt flag is also set when the
checksum is invalid as well.
V2:
- Removed the static bool global
- Added a bool to the drm_connector struct to reaplce the static one for
holding the status of raw edid header corruption detection
- Modified the function signature of the is_valid function to take an
additional parameter to store the corruption detected value
- Fixed the other callers of the above is_valid function
V3:
- Updated the commit message to be more clear about what and why this
patch does what it does.
- Added comment in code to clarify the operations there
- Removed compliance variable and check_link_status update; those
have been moved to a later patch
- Removed variable assignment from the bottom of the test handler
V4:
- Removed i915 tag from subject line as the patch is not i915-specific
V5:
- Moved code causing a compilation error to this patch where the variable
is actually declared
- Maintained blank lines / spacing so as to not contaminate the patch
V6:
- Removed extra debug messages
- Added documentation to for the added parameter on drm_edid_block_valid
- Fixed more whitespace issues in check_link_status
- Added a clear of the header_corrupt flag to the end of the test handler
in intel_dp.c
- Changed the usage of the new function prototype in several places to use
NULL where it is not needed by compliance testing
V7:
- Updated to account for long_pulse flag propagation
V8:
- Removed clearing of header_corrupt flag from the test handler in intel_dp.c
- Added clearing of header_corrupt flag in the drm_edid_block_valid function
V9:
- Renamed header_corrupt flag to edid_corrupt to more accurately reflect its
value and purpose
- Updated commit message
V10:
- Updated for versioning and patch swizzle
- Revised the title to more accurately reflect the nature and contents of
the patch
- Fixed formatting/whitespace problems
- Added set flag when computed checksum is invalid
Signed-off-by: Todd Previte <tprevite@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If the user supplies EDID through firmware or debugfs override, the
driver callbacks are bypassed and the connector ELD does not get
updated, and audio fails. Set ELD for firmware and debugfs EDIDs too.
There should be no harm in gratuitously doing this for non HDMI/DP
connectors, as it's still up to the driver to use the ELD, if any.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82349
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=80691
Reported-by: Emil <emilsvennesson@gmail.com>
Reported-by: Rob Engle <grenoble@gmail.com>
Tested-by: Jolan Luff <jolan@gormsby.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
"release_firmware"
The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Generated using semantic patch:
@@
expression E;
@@
- drm_get_connector_name(E)
+ E->name
[airlied: regenerated]
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The 800x600 (SVGA) screen resolution was lacking in the set of
built-in selectable EDID screen resolutions that can be used to
repair misbehaving monitor firmware.
This patch adds the related data set and expands the documentation.
Note that the SVGA bit occupies a different byte to all the existing
users of the established timing bits forcing a rework of the
ESTABLISHED_TIMINGS_BITS macro.
Tested new EDID on an aged (and misbehaving) industrial LCD panel;
existing EDIDs still pass edid-decode's checksum checks.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: linux-doc@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Always use "void *" for arbitrary memory buffers, as this allows to drop
casts in assignments.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
If the firmware is not builtin and userspace is not yet running, we can
stall the boot process for a minute whilst the firmware loader times
out. This is contrary to expectations of providing a builtin EDID!
In the process, we can rearrange the code to make the error handling
more resilient and prevent gcc warning about unitialised variables along
the error paths.
v2: Load builtins first, fix gcc second (Jani) and cosmetics (Ville).
v3: Verify that we do not read beyond the end of the fwdata (Ville)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Use "const char *" instead of "char *" in order to avoid this warning:
drivers/gpu/drm/drm_edid_load.c: In function ‘drm_load_edid_firmware’:
drivers/gpu/drm/drm_edid_load.c:245:25: warning: initialization discards ‘const’ qualifier from pointer target type [enabled by default]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The 1600x1200 (UXGA) screen resolution was lacking in the set of
built-in selectable EDID screen resolutions that can be used to
repair misbehaving monitor firmware.
This patch adds the related data set and expands the documentation.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
|
|
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
|
|
Limit printing bad edid information at one time per connector.
Connector that are connected to a bad monitor/kvm will likely
stay connected to the same bad monitor/kvm and it makes no
sense to keep printing the bad edid message.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Neither the drm core nor any of the drivers really need the raw_edid field
of struct drm_display_info for anything. Instead of being useful, it
creates confusion about who is responsible for freeing the memory it points
to and setting the field to NULL afterwards, leading to memory leaks and
dangling pointers.
Remove the raw_edid field, and fix drivers as necessary.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Do not leak memory by updating pointer with potentially
NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
this fixes a report that the new load code needed to be updated for
ajax's validity changes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Broken monitors and/or broken graphic boards may send erroneous or no
EDID data. This also applies to broken KVM devices that are unable to
correctly forward the EDID data of the connected monitor but invent
their own fantasy data.
This patch allows to specify an EDID data set to be used instead of
probing the monitor for it. It contains built-in data sets of frequently
used screen resolutions. In addition, a particular EDID data set may be
provided in the /lib/firmware directory and loaded via the firmware
interface. The name is passed to the kernel as module parameter of the
drm_kms_helper module either when loaded
options drm_kms_helper edid_firmware=edid/1280x1024.bin
or as kernel commandline parameter
drm_kms_helper.edid_firmware=edid/1280x1024.bin
It is also possible to restrict the usage of a specified EDID data set
to a particular connector. This is done by prepending the name of the
connector to the name of the EDID data set using the syntax
edid_firmware=[<connector>:]<edid>
such as, for example,
edid_firmware=DVI-I-1:edid/1920x1080.bin
in which case no other connector will be affected.
The built-in data sets are
Resolution Name
--------------------------------
1024x768 edid/1024x768.bin
1280x1024 edid/1280x1024.bin
1680x1050 edid/1680x1050.bin
1920x1080 edid/1920x1080.bin
They are ignored, if a file with the same name is available in the
/lib/firmware directory.
The built-in EDID data sets are based on standard timings that may not
apply to a particular monitor and even crash it. Ideally, EDID data of
the connected monitor should be used. They may be obtained through the
drm/cardX/cardX-<connector>/edid entry in the /sys/devices PCI directory
of a correctly working graphics adapter.
It is even possible to specify the name of an EDID data set on-the-fly
via the /sys/module interface, e.g.
echo edid/myedid.bin >/sys/module/drm_kms_helper/parameters/edid_firmware
The new screen mode is considered when the related kernel function is
called for the first time after the change. Such calls are made when the
X server is started or when the display settings dialog is opened in an
already running X server.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|