Age | Commit message (Collapse) | Author | Files | Lines |
|
The DP component's unbind operation walks through the submodules to
unregister and clean things up. But if the unbind happens because the DP
controller itself is being removed, all the memory for those submodules
has just been freed.
Change the order of these operations to avoid the many use-after-free
that otherwise happens in this code path.
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542166/
Link: https://lore.kernel.org/r/20230612220259.1884381-1-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Using devres to depopulate the aux bus made sure that upon a probe
deferral the EDP panel device would be destroyed and recreated upon next
attempt.
But the struct device which the devres is tied to is the DPUs
(drm_dev->dev), which may be happen after the DP controller is torn
down.
Indications of this can be seen in the commonly seen EDID-hexdump full
of zeros in the log, or the occasional/rare KASAN fault where the
panel's attempt to read the EDID information causes a use after free on
DP resources.
It's tempting to move the devres to the DP controller's struct device,
but the resources used by the device(s) on the aux bus are explicitly
torn down in the error path. The KASAN-reported use-after-free also
remains, as the DP aux "module" explicitly frees its devres-allocated
memory in this code path.
As such, explicitly depopulate the aux bus in the error path, and in the
component unbind path, to avoid these issues.
Fixes: 2b57f726611e ("drm/msm/dp: fix aux-bus EP lifetime")
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/542163/
Link: https://lore.kernel.org/r/20230612220106.1884039-1-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
'msm-next-lumag-dp', 'msm-next-lumag-dsi' and 'msm-next-lumag-mdp5' into msm-next-lumag
Core:
- Add Marijn Suijten as drm/msm reviewer
- Adreno A660 bindings
- SM8350 MDSS bindings fix
DP:
- Removed obsolete USB-PD remains
- Documented DP compatible string for sm8550 platform
DPU:
- Added support for DPU on sm6350 and sm6375 platforms
- Implemented tearcheck support to support vsync on SM150 and newer platforms
- Enabled missing features (DSPP, DSC, split display) on sc8180x, sc8280xp, sm8450
- Enabled writeback on sc7280
- Enabled DSC on msm8998
- Native HDMI output support
- Dropped unused features: regdma, GC, IGC
- Fixed the DSC flush operations
- Simplified QoS handling, removing obsolete and unused features and merging
SSPP and WB code paths
- Reworked dpu_encoder initialisation path
DSI:
- Added support for DSI and 28nm DSI PHY on MSM8226 platform
- Added support for DSI on sm6350 and sm6375 platforms
- Dropped powerup quirks in favour of using pre_enable_prev_first for
downstream bridges
- Fixed 14nm DSI PHY programming
MDP5:
- Added support for display controller on MSM8226 platform
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
The internal_hpd flag is set to true by dp_bridge_hpd_enable() and set to
false by dp_bridge_hpd_disable() to handle GPIO pinmuxed into DP controller
case. HDP related interrupts can not be enabled until internal_hpd is set
to true. At current implementation dp_display_config_hpd() will initialize
DP host controller first followed by enabling HDP related interrupts if
internal_hpd was true at that time. Enable HDP related interrupts depends on
internal_hpd status may leave system with DP driver host is in running state
but without HDP related interrupts being enabled. This will prevent external
display from being detected. Eliminated this dependency by moving HDP related
interrupts enable/disable be done at dp_bridge_hpd_enable/disable() directly
regardless of internal_hpd status.
Changes in V3:
-- dp_catalog_ctrl_hpd_enable() and dp_catalog_ctrl_hpd_disable()
-- rewording ocmmit text
Changes in V4:
-- replace dp_display_config_hpd() with dp_display_host_start()
-- move enable_irq() at dp_display_host_start();
Changes in V5:
-- replace dp_display_host_start() with dp_display_host_init()
Changes in V6:
-- squash remove enable_irq() and disable_irq()
Fixes: cd198caddea7 ("drm/msm/dp: Rely on hpd_enable/disable callbacks")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Leonard Lausen <leonard@lausen.nl> # on sc7180 lazor
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/1684878756-17830-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The dp_power module keeps track of both the DP controller's struct
platform_device and struct device - with the prior pulled out of the
dp_parser module.
Clean up the duplication by dropping the platform_device reference and
just track the passed struct device.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/536939/
Link: https://lore.kernel.org/r/20230515030256.300104-3-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
The clk_bulk API already provides error messages indicating which
specific clock in the request for which the operation failed, further
more these errors are associated with the specific DisplayPort
controller (rather than the shared drm_device). The additional error
messages int he dp_power module does thereby not provide any benefit.
While at it, none of the dp_power handles passed to these functions are
dynamic in nature, so there should not be any need for runtime checking
them. Drop these as well.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/536938/
Link: https://lore.kernel.org/r/20230515030256.300104-2-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Remove most of remains of downstream usbpd code. Mainline kernel uses
different approach for managing Type-C / USB-PD, so this remains unused.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/538270/
Link: https://lore.kernel.org/r/20230520182050.4014143-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
On sc7280 where eDP is the primary display, PSR is causing
IGT breakage even for basic test cases like kms_atomic and
kms_atomic_transition. Most often the issue starts with below
stack so providing that as reference
Call trace:
dpu_encoder_assign_crtc+0x64/0x6c
dpu_crtc_enable+0x188/0x204
drm_atomic_helper_commit_modeset_enables+0xc0/0x274
msm_atomic_commit_tail+0x1a8/0x68c
commit_tail+0xb0/0x160
drm_atomic_helper_commit+0x11c/0x124
drm_atomic_commit+0xb0/0xdc
drm_atomic_connector_commit_dpms+0xf4/0x110
drm_mode_obj_set_property_ioctl+0x16c/0x3b0
drm_connector_property_set_ioctl+0x4c/0x74
drm_ioctl_kernel+0xec/0x15c
drm_ioctl+0x264/0x408
__arm64_sys_ioctl+0x9c/0xd4
invoke_syscall+0x4c/0x110
el0_svc_common+0x94/0xfc
do_el0_svc+0x3c/0xb0
el0_svc+0x2c/0x7c
el0t_64_sync_handler+0x48/0x114
el0t_64_sync+0x190/0x194
---[ end trace 0000000000000000 ]---
[drm-dp] dp_ctrl_push_idle: PUSH_IDLE pattern timedout
Other basic use-cases still seem to work fine hence add a
a module parameter to allow toggling psr enable/disable till
PSR related issues are hashed out with IGT.
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/534420/
Link: https://lore.kernel.org/r/20230427232848.5200-1-quic_abhinavk@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
while binding the code always registers a audio driver, however there
is no corresponding unregistration done in unbind. This leads to multiple
redundant audio platform devices if dp_display_bind and dp_display_unbind
happens multiple times during startup. On X13s platform this resulted in
6 to 9 audio codec device instead of just 3 codec devices for 3 dp ports.
Fix this by unregistering codecs on unbind.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: d13e36d7d222 ("drm/msm/dp: add audio support for Display Port on MSM")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/533324/
Link: https://lore.kernel.org/r/20230421145657.12186-1-srinivas.kandagatla@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
There is a spelling mistake in a drm_dbg_dp message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/526658/
Link: https://lore.kernel.org/r/20230314082050.26331-1-colin.i.king@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
If our interrupt handler gets called and we don't really handle the
interrupt then we should return IRQ_NONE. The current interrupt
handler didn't do this, so let's fix it.
NOTE: for some of the cases it's clear that we should return IRQ_NONE
and some cases it's clear that we should return IRQ_HANDLED. However,
there are a few that fall somewhere in between. Specifically, the
documentation for when to return IRQ_NONE vs. IRQ_HANDLED is probably
best spelled out in the commit message of commit d9e4ad5badf4 ("Document
that IRQ_NONE should be returned when IRQ not actually handled"). That
commit makes it clear that we should return IRQ_HANDLED if we've done
something to make the interrupt stop happening.
The case where it's unclear is, for instance, in dp_aux_isr() after
we've read the interrupt using dp_catalog_aux_get_irq() and confirmed
that "isr" is non-zero. The function dp_catalog_aux_get_irq() not only
reads the interrupts but it also "ack"s all the interrupts that are
returned. For an "unknown" interrupt this has a very good chance of
actually stopping the interrupt from happening. That would mean we've
identified that it's our device and done something to stop them from
happening and should return IRQ_HANDLED. Specifically, it should be
noted that most interrupts that need "ack"ing are ones that are
one-time events and doing an "ack" is enough to clear them. However,
since these interrupts are unknown then, by definition, it's unknown
if "ack"ing them is truly enough to clear them. It's possible that we
also need to remove the original source of the interrupt. In this
case, IRQ_NONE would be a better choice.
Given that returning an occasional IRQ_NONE isn't the absolute end of
the world, however, let's choose that course of action. The IRQ
framework will forgive a few IRQ_NONE returns now and again (and it
won't even log them, which is why we have to log them ourselves). This
means that if we _do_ end hitting an interrupt where "ack"ing isn't
enough the kernel will eventually detect the problem and shut our
device down.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/520660/
Link: https://lore.kernel.org/r/20230126170745.v2.2.I2d7aec2fadb9c237cd0090a47d6a8ba2054bf0f8@changeid
[DB: reformatted commit message to make checkpatch happy]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
The DP AUX interrupt handling was a bit of a mess.
* There were two functions (one for "native" transfers and one for
"i2c" transfers) that were quite similar. It was hard to say how
many of the differences between the two functions were on purpose
and how many of them were just an accident of how they were coded.
* Each function sometimes used "else if" to test for error bits and
sometimes didn't and again it was hard to say if this was on purpose
or just an accident.
* The two functions wouldn't notice whether "unknown" bits were
set. For instance, there seems to be a bit "DP_INTR_PLL_UNLOCKED"
and if it was set there would be no indication.
* The two functions wouldn't notice if more than one error was set.
Let's fix this by being more consistent / explicit about what we're
doing.
By design this could cause different handling for AUX transfers,
though I'm not actually aware of any bug fixed as a result of
this patch (this patch was created because we simply noticed how odd
the old code was by code inspection). Specific notes here:
1. In the old native transfer case if we got "done + wrong address"
we'd ignore the "wrong address" (because of the "else if"). Now we
won't.
2. In the old native transfer case if we got "done + timeout" we'd
ignore the "timeout" (because of the "else if"). Now we won't.
3. In the old native transfer case we'd see "nack_defer" and translate
it to the error number for "nack". This differed from the i2c
transfer case where "nack_defer" was given the error number for
"nack_defer". This 100% can't matter because the only user of this
error number treats "nack defer" the same as "nack", so it's clear
that the difference between the "native" and "i2c" was pointless
here.
4. In the old i2c transfer case if we got "done" plus any error
besides "nack" or "defer" then we'd ignore the error. Now we don't.
5. If there is more than one error signaled by the hardware it's
possible that we'll report a different one than we used to. I don't
know if this matters. If someone is aware of a case this matters we
should document it and change the code to make it explicit.
6. One quirk we keep (I don't know if this is important) is that in
the i2c transfer case if we see "done + defer" we report that as a
"nack". That seemed too intentional in the old code to just drop.
After this change we will add extra logging, including:
* A warning if we see more than one error bit set.
* A warning if we see an unexpected interrupt.
* A warning if we get an AUX transfer interrupt when shouldn't.
It actually turns out that as a result of this change then at boot we
sometimes see an error:
[drm:dp_aux_isr] *ERROR* Unexpected DP AUX IRQ 0x01000000 when not busy
That means that, during init, we are seeing DP_INTR_PLL_UNLOCKED. For
now I'm going to say that leaving this error reported in the logs is
OK-ish and hopefully it will encourage someone to track down what's
going on at init time.
One last note here is that this change renames one of the interrupt
bits. The bit named "i2c done" clearly was used for native transfers
being done too, so I renamed it to indicate this.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/520658/
Link: https://lore.kernel.org/r/20230126170745.v2.1.I90ffed3ddd21e818ae534f820cb4d6d8638859ab@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
For the PSR to kick in, self_refresh_aware has to be set.
Initialize it based on the PSR support for the eDP interface.
Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/524743/
Link: https://lore.kernel.org/r/1677774797-31063-15-git-send-email-quic_vpolimer@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
The eDP and DP interfaces shared the bridge operations and
the eDP specific changes were implemented under is_edp check.
To add psr support for eDP, we started using a new set of eDP
bridge ops. We are moving the eDP specific code in the
dp_bridge_mode_valid function to a new eDP function,
edp_bridge_mode_valid under the eDP bridge ops.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/524736/
Link: https://lore.kernel.org/r/1677774797-31063-11-git-send-email-quic_vpolimer@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Add support for basic panel self refresh (PSR) feature for eDP.
Add a new interface to set PSR state in the sink from DPU.
Program the eDP controller to issue PSR enter and exit SDP to
the sink.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/524734/
Link: https://lore.kernel.org/r/1677774797-31063-10-git-send-email-quic_vpolimer@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Use atomic variants for DP bridge callback functions so that
the atomic state can be accessed in the interface drivers.
The atomic state will help the driver find out if the display
is in self refresh state.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/524731/
Link: https://lore.kernel.org/r/1677774797-31063-9-git-send-email-quic_vpolimer@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Merge display-related changes targeting Qualcomm DRM MSM driver.
Notable changes:
DPU, DSI, MDSS:
- Support for SM8350, SM8450 SM8550 and SC8280XP platform
Core:
- Added bindings for SM8150 (driver support already present)
DPU:
- Partial support for DSC on SM8150 and SM8250
- Fixed color transformation matrix being lost on suspend/resume
DP:
- Support for DP on SDM845 and SC8280XP platforms
- HPD fixes
- Support for limiting DP link rate via DT property, this enables
support for HBR3 rates.
DSI:
- Validate display modes according to the DSI OPP table
- DSI PHY support for the SM6375 platform
- Fixed byte intf clock selection for 14nm PHYs
MDP5:
- Schema conversion to YAML
Misc fixes as usual
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
During initalization of the DisplayPort controller an EV_HPD_INIT_SETUP
event is generated, but with a delay of 100 units. This delay existed to
circumvent bug in the QMP combo PHY driver, where if the DP part was
powered up before USB, the common properties would not be properly
initialized - and USB wouldn't work.
This issue was resolved in the recent refactoring of the QMP driver,
so it's now possible to remove this delay.
While there is still a timing dependency in the current implementation,
test indicates that it's now possible to boot with an external display
on USB Type-C and have the display power up, without disconnecting and
reconnecting the cable.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/518729/
Link: https://lore.kernel.org/r/20230117172951.2748456-1-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
By default, HBR2 (5.4G) is the max link rate be supported. This patch
uses the actual limit specified by DT and removes the artificial
limitation to 5.4 Gbps. Supporting HBR3 is a consequence of that.
Changes in v2:
-- add max link rate from dtsi
Changes in v3:
-- parser max_data_lanes and max_dp_link_rate from dp_out endpoint
Changes in v4:
-- delete unnecessary pr_err
Changes in v5:
-- split parser function into different patch
Changes in v9:
-- revised commit test
Changes in v13:
-- repalced "properity" with "property"
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/516097/
Link: https://lore.kernel.org/r/1672163103-31254-6-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
from link-frequencies property of dp_out endpoint
Changes in v6:
-- second patch after split parser patch into two patches
Changes in v7:
-- without checking cnt against DP_MAX_NUM_DP_LANES to retrieve link rate
Changes in v9:
-- separate parser link-frequencies out of data-lanes
Changes in v10:
-- add dp_parser_link_frequencies()
Changes in v11:
-- return 0 if(!endpoint)
Changes in v12:
-- replace khz with kbytes at dp_parser.h
Changes in v14:
-- replace "parser" with "parse" at commit subject
-- use do_div() for 64 bits division
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/516100/
Link: https://lore.kernel.org/r/1672163103-31254-5-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Add capability to parser data-lanes as property of dp_out endpoint.
Also retain the original capability to parser data-lanes as property
of mdss_dp node to handle legacy case.
Changes in v6:
-- first patch after split parser patch into two
Changes in v7:
-- check "data-lanes" from endpoint first
Changes in v14:
-- replace "parser" with "parse" at commit subject
-- add matching brackets at dp_parser_misc()
Changes in v15:
-- concise dp_parser_misc()
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/516096/
Link: https://lore.kernel.org/r/1672163103-31254-4-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
The DisplayPort controller's hot-plug mechanism is based on pinmuxing a
physical signal on a GPIO pin into the controller. This is not always
possible, either because there aren't dedicated GPIOs available or
because the hot-plug signal is a virtual notification, in cases such as
USB Type-C.
For these cases, by implementing the hpd_notify() callback for the
DisplayPort controller's drm_bridge, a downstream drm_bridge
(next_bridge) can be used to track and signal the connection status
changes.
This makes it possible to use downstream drm_bridges such as
display-connector or any virtual mechanism, as long as they are
implemented as a drm_bridge.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[bjorn: Drop connector->fwnode assignment and dev from struct msm_dp]
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/514410/
Link: https://lore.kernel.org/r/20221207220012.16529-10-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
The DisplayPort controller's internal HPD interrupt handling is used for
cases where the HPD signal is connected to a GPIO which is pinmuxed into
the DisplayPort controller. In other configurations the HPD notification
might be delivered by the DRM framework from an associated bridge.
This difference is not appropriately represented by the "is_edp"
boolean, but is properly represented by the frameworks invocation of the
hpd_enable() and hpd_disable() callbacks. Switch the current condition
to rely on these callbacks instead.
This ensures appropriate handling of the three cases; no bridge
connected, a bridge without DRM_BRIDGE_OP_HPD and a bridge with
DRM_BRIDGE_OP_HPD.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/514414/
Link: https://lore.kernel.org/r/20221207220012.16529-9-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
The Qualcomm SDM845 platform has a single DisplayPort controller, with
the same design as SC7180, so add support for this by reusing the SC7180
definition.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/514395/
Link: https://lore.kernel.org/r/20221207220012.16529-8-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
The SC8280XP platform has four DisplayPort controllers, per MDSS
instance, all with widebus support.
The first two are defined to be DisplayPort only, while the latter pair
(of each instance) can be either DisplayPort or Embedded DisplayPort.
The two sets are tied to the possible compatibels.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/514394/
Link: https://lore.kernel.org/r/20221207220012.16529-7-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
In the SC8280XP platform there are two identical MDSS instances, each
with the same set of DisplayPort instances, at different addresses.
By not relying on the index to define the instance id it's possible to
describe them both in the same table and hence have a single compatible.
While at it, flatten the cfg/desc structure so that the match data is
just an array of descs.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/514397/
Link: https://lore.kernel.org/r/20221207220012.16529-6-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
There are 3 possible interrupt sources are handled by DP controller,
HPDstatus, Controller state changes and Aux read/write transaction.
At every irq, DP controller have to check isr status of every interrupt
sources and service the interrupt if its isr status bits shows interrupts
are pending. There is potential race condition may happen at current aux
isr handler implementation since it is always complete dp_aux_cmd_fifo_tx()
even irq is not for aux read or write transaction. This may cause aux read
transaction return premature if host aux data read is in the middle of
waiting for sink to complete transferring data to host while irq happen.
This will cause host's receiving buffer contains unexpected data. This
patch fixes this problem by checking aux isr and return immediately at
aux isr handler if there are no any isr status bits set.
Current there is a bug report regrading eDP edid corruption happen during
system booting up. After lengthy debugging to found that VIDEO_READY
interrupt was continuously firing during system booting up which cause
dp_aux_isr() to complete dp_aux_cmd_fifo_tx() prematurely to retrieve data
from aux hardware buffer which is not yet contains complete data transfer
from sink. This cause edid corruption.
Follows are the signature at kernel logs when problem happen,
EDID has corrupt header
panel-simple-dp-aux aux-aea0000.edp: Couldn't identify panel via EDID
Changes in v2:
-- do complete if (ret == IRQ_HANDLED) ay dp-aux_isr()
-- add more commit text
Changes in v3:
-- add Stephen suggested
-- dp_aux_isr() return IRQ_XXX back to caller
-- dp_ctrl_isr() return IRQ_XXX back to caller
Changes in v4:
-- split into two patches
Changes in v5:
-- delete empty line between tags
Changes in v6:
-- remove extra "that" and fixed line more than 75 char at commit text
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/516121/
Link: https://lore.kernel.org/r/1672193785-11003-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
https://gitlab.freedesktop.org/lumag/msm into drm-next
drm/msm updates for 6.2
Core:
- MSM_INFO_GET_FLAGS support
- Cleaned up MSM IOMMU wrapper code
DPU:
- Added support for XR30 and P010 image formats
- Reworked MDSS/DPU schema, added SM8250 MDSS bindings
- Added Qualcomm SM6115 support
DP:
- Dropped unsane sanity checks
DSI:
- Fix calculation of DSC pps payload
DSI PHY:
- DSI PHY support for QCM2290
HDMI:
- Reworked dev init path
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221126102141.721353-1-dmitry.baryshkov@linaro.org
|
|
Linux 6.1-rc6
This is needed for drm-misc-next and tegra.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107192545.9896-5-ville.syrjala@linux.intel.com
|
|
Drop the overly defensive modeset sanity checks of function parameters
which have already been checked or used by the callers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/502674/
Link: https://lore.kernel.org/r/20220913085320.8577-10-johan+linaro@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Bring sink out of D3 (power down) mode into D0 (normal operation) mode
by setting DP_SET_POWER_D0 bit to DP_SET_POWER dpcd register. This
patch will retry 3 times if written to DP_SET_POWER register failed.
Changes in v5:
-- split into two patches
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/502536/
Link: https://lore.kernel.org/r/1662999830-13916-4-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
drm_dp_dpcd_readb() will return 1 to indicate one byte had been read
successfully. This patch replace variable "err" with "len" have more
correct meaning.
changes in v5:
-- split into 3 patches
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/502533/
Link: https://lore.kernel.org/r/1662999830-13916-3-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
DOWNSPREAD_CTRL (0x107) shall be cleared to 0 upon power-on reset or an
upstream device disconnect. This patch will enforce this rule by always
cleared DOWNSPREAD_CTRL register to 0 before start link training. At rare
case that DP MSA timing parameters may be mis-interpreted by the sink
which causes audio sampling rate be calculated wrongly and cause audio
did not work at sink if DOWNSPREAD_CTRL register is not cleared to 0.
Changes in v2:
1) fix spelling at commit text
2) merge ssc variable into encoding[0]
Changes in v3:
-- correct spelling of DOWNSPREAD_CTRL
-- replace err with len of ssize_t
Changes in v4:
-- split into 2 patches
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Patchwork: https://patchwork.freedesktop.org/patch/502532/
Link: https://lore.kernel.org/r/1662999830-13916-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
Device-managed resources allocated post component bind must be tied to
the lifetime of the aggregate DRM device or they will not necessarily be
released when binding of the aggregate device is deferred.
This can lead resource leaks or failure to bind the aggregate device
when binding is later retried and a second attempt to allocate the
resources is made.
For the DP bridges, previously allocated bridges will leak on probe
deferral.
Fix this by amending the DP parser interface and tying the lifetime of
the bridge device to the DRM device rather than DP platform device.
Fixes: c3bf8e21b38a ("drm/msm/dp: Add eDP support via aux_bus")
Cc: stable@vger.kernel.org # 5.19
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/502667/
Link: https://lore.kernel.org/r/20220913085320.8577-8-johan+linaro@kernel.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
Device-managed resources allocated post component bind must be tied to
the lifetime of the aggregate DRM device or they will not necessarily be
released when binding of the aggregate device is deferred.
This can lead resource leaks or failure to bind the aggregate device
when binding is later retried and a second attempt to allocate the
resources is made.
For the DP aux-bus, an attempt to populate the bus a second time will
simply fail ("DP AUX EP device already populated").
Fix this by tying the lifetime of the EP device to the DRM device rather
than DP controller platform device.
Fixes: c3bf8e21b38a ("drm/msm/dp: Add eDP support via aux_bus")
Cc: stable@vger.kernel.org # 5.19
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/502672/
Link: https://lore.kernel.org/r/20220913085320.8577-7-johan+linaro@kernel.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
Device-managed resources allocated post component bind must be tied to
the lifetime of the aggregate DRM device or they will not necessarily be
released when binding of the aggregate device is deferred.
This is specifically true for the DP IRQ, which will otherwise remain
requested so that the next bind attempt fails when requesting the IRQ a
second time.
Since commit c3bf8e21b38a ("drm/msm/dp: Add eDP support via aux_bus")
this can happen when the aux-bus panel driver has not yet been loaded so
that probe is deferred.
Fix this by tying the device-managed lifetime of the DP IRQ to the DRM
device so that it is released when bind fails.
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Cc: stable@vger.kernel.org # 5.10
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/502679/
Link: https://lore.kernel.org/r/20220913085320.8577-6-johan+linaro@kernel.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
Add the missing sanity check on the bridge counter to avoid corrupting
data beyond the fixed-sized bridge array in case there are ever more
than eight bridges.
Fixes: 8a3b4c17f863 ("drm/msm/dp: employ bridge mechanism for display enable and disable")
Cc: stable@vger.kernel.org # 5.17
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/502664/
Link: https://lore.kernel.org/r/20220913085320.8577-3-johan+linaro@kernel.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
DRM commit_tails() will disable downstream crtc/encoder/bridge if
both disable crtc is required and crtc->active is set before pushing
a new frame downstream.
There is a rare case that user space display manager issue an extra
screen update immediately followed by close DRM device while down
stream display interface is disabled. This extra screen update will
timeout due to the downstream interface is disabled but will cause
crtc->active be set. Hence the followed commit_tails() called by
drm_release() will pass the disable downstream crtc/encoder/bridge
conditions checking even downstream interface is disabled.
This cause the crash to happen at dp_bridge_disable() due to it trying
to access the main link register to push the idle pattern out while main
link clocks is disabled.
This patch adds atomic_check to prevent the extra frame will not
be pushed down if display interface is down so that crtc->active
will not be set neither. This will fail the conditions checking
of disabling down stream crtc/encoder/bridge which prevent
drm_release() from calling dp_bridge_disable() so that crash
at dp_bridge_disable() prevented.
There is no protection in the DRM framework to check if the display
pipeline has been already disabled before trying again. The only
check is the crtc_state->active but this is controlled by usermode
using UAPI. Hence if the usermode sets this and then crashes, the
driver needs to protect against double disable.
SError Interrupt on CPU7, code 0x00000000be000411 -- SError
CPU: 7 PID: 3878 Comm: Xorg Not tainted 5.19.0-stb-cbq #19
Hardware name: Google Lazor (rev3 - 8) (DT)
pstate: a04000c9 (NzCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __cmpxchg_case_acq_32+0x14/0x2c
lr : do_raw_spin_lock+0xa4/0xdc
sp : ffffffc01092b6a0
x29: ffffffc01092b6a0 x28: 0000000000000028 x27: 0000000000000038
x26: 0000000000000004 x25: ffffffd2973dce48 x24: 0000000000000000
x23: 00000000ffffffff x22: 00000000ffffffff x21: ffffffd2978d0008
x20: ffffffd2978d0008 x19: ffffff80ff759fc0 x18: 0000000000000000
x17: 004800a501260460 x16: 0441043b04600438 x15: 04380000089807d0
x14: 07b0089807800780 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000438 x10: 00000000000007d0 x9 : ffffffd2973e09e4
x8 : ffffff8092d53300 x7 : ffffff808902e8b8 x6 : 0000000000000001
x5 : ffffff808902e880 x4 : 0000000000000000 x3 : ffffff80ff759fc0
x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffffff80ff759fc0
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 7 PID: 3878 Comm: Xorg Not tainted 5.19.0-stb-cbq #19
Hardware name: Google Lazor (rev3 - 8) (DT)
Call trace:
dump_backtrace.part.0+0xbc/0xe4
show_stack+0x24/0x70
dump_stack_lvl+0x68/0x84
dump_stack+0x18/0x34
panic+0x14c/0x32c
nmi_panic+0x58/0x7c
arm64_serror_panic+0x78/0x84
do_serror+0x40/0x64
el1h_64_error_handler+0x30/0x48
el1h_64_error+0x68/0x6c
__cmpxchg_case_acq_32+0x14/0x2c
_raw_spin_lock_irqsave+0x38/0x4c
lock_timer_base+0x40/0x78
__mod_timer+0xf4/0x25c
schedule_timeout+0xd4/0xfc
__wait_for_common+0xac/0x140
wait_for_completion_timeout+0x2c/0x54
dp_ctrl_push_idle+0x40/0x88
dp_bridge_disable+0x24/0x30
drm_atomic_bridge_chain_disable+0x90/0xbc
drm_atomic_helper_commit_modeset_disables+0x198/0x444
msm_atomic_commit_tail+0x1d0/0x374
commit_tail+0x80/0x108
drm_atomic_helper_commit+0x118/0x11c
drm_atomic_commit+0xb4/0xe0
drm_client_modeset_commit_atomic+0x184/0x224
drm_client_modeset_commit_locked+0x58/0x160
drm_client_modeset_commit+0x3c/0x64
__drm_fb_helper_restore_fbdev_mode_unlocked+0x98/0xac
drm_fb_helper_set_par+0x74/0x80
drm_fb_helper_hotplug_event+0xdc/0xe0
__drm_fb_helper_restore_fbdev_mode_unlocked+0x7c/0xac
drm_fb_helper_restore_fbdev_mode_unlocked+0x20/0x2c
drm_fb_helper_lastclose+0x20/0x2c
drm_lastclose+0x44/0x6c
drm_release+0x88/0xd4
__fput+0x104/0x220
____fput+0x1c/0x28
task_work_run+0x8c/0x100
do_exit+0x450/0x8d0
do_group_exit+0x40/0xac
__wake_up_parent+0x0/0x38
invoke_syscall+0x84/0x11c
el0_svc_common.constprop.0+0xb8/0xe4
do_el0_svc+0x8c/0xb8
el0_svc+0x2c/0x54
el0t_64_sync_handler+0x120/0x1c0
el0t_64_sync+0x190/0x194
SMP: stopping secondary CPUs
Kernel Offset: 0x128e800000 from 0xffffffc008000000
PHYS_OFFSET: 0x80000000
CPU features: 0x800,00c2a015,19801c82
Memory Limit: none
Changes in v2:
-- add more commit text
Changes in v3:
-- add comments into dp_bridge_atomic_check()
Changes in v4:
-- rewording the comment into dp_bridge_atomic_check()
Changes in v5:
-- removed quote x at end of commit text
Changes in v6:
-- removed quote x at end of comment in dp_bridge_atomic_check()
Fixes: 8a3b4c17f863 ("drm/msm/dp: employ bridge mechanism for display enable and disable")
Reported-by: Leonard Lausen <leonard@lausen.nl>
Suggested-by: Rob Clark <robdclark@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/17
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/505331/
Link: https://lore.kernel.org/r/1664408211-25314-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
At current implementation there is an extra 0 at 1.62G link rate which
cause no correct pixel_div selected for 1.62G link rate to calculate
mvid and nvid. This patch delete the extra 0 to have mvid and nvid be
calculated correctly.
Changes in v2:
-- fix Fixes tag's text
Changes in v3:
-- fix misspelling of "Reviewed-by"
Fixes: 937f941ca06f ("drm/msm/dp: Use qmp phy for DP PLL and PHY")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/499328/
Link: https://lore.kernel.org/r/1661372150-3764-1-git-send-email-quic_khsieh@quicinc.com
[DB: rewrapped commit message]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Build robots complain
smatch warnings:
drivers/gpu/drm/msm/dp/dp_link.c:969 dp_link_process_link_status_update() warn: inconsistent indenting
Fix it along with a trailing space from the same commit.
Cc: Kuogee Hsieh <quic_khsieh@quicinc.com>
Fixes: ea530388e64b ("drm/msm/dp: skip checking LINK_STATUS_UPDATED bit")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/498954/
Link: https://lore.kernel.org/r/20220823212302.1744145-1-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
This API isn't really more than a couple lines now that we don't store
the pixel_rate to the struct member. Inline it into the caller.
Cc: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/490775/
Link: https://lore.kernel.org/r/20220623002540.871994-4-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
This struct member is stored to in the function that calls the function
which uses it. That's possible with a function argument instead of
storing to a struct member. Pass the pixel_rate as an argument instead
to simplify the code. Note that dp_ctrl_link_maintenance() was storing
the pixel_rate but never using it so we just remove the assignment from
there.
Cc: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/490772/
Link: https://lore.kernel.org/r/20220623002540.871994-3-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Let's move these functions around to avoid having to forward declare
dp_ctrl_on_stream_phy_test_report(). Also remove
dp_ctrl_reinitialize_mainlink() forward declaration because we're doing
that sort of task.
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/490771/
Link: https://lore.kernel.org/r/20220623002540.871994-2-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Data Symbols scrambled is required for tps4 at link training 2.
Therefore SCRAMBLING_DISABLE bit should not be set for tps4 to
work.
RECOVERED_CLOCK_OUT_EN is for enable simple EYE test for jitter
measurement with minimal equipment for embedded applications purpose
and is not required to be set during normal operation. Current
implementation always have RECOVERED_CLOCK_OUT_EN bit set which
cause SCRAMBLING_DISABLE bit wrongly set at tps4 which prevent
tps4 from working.
This patch delete setting RECOVERED_CLOCK_OUT_EN to fix
SCRAMBLING_DISABLE be wrongly set at tps4.
Changes in v2:
-- fix Fixes tag
Changes in v3:
-- revise commit text
Changes in v4:
-- fix commit text newline
Changes in v5:
-- fix commit text line over 75 chars
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/497194/
Link: https://lore.kernel.org/r/1660258670-4200-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the large set of char and misc and other driver subsystem
changes for 6.0-rc1.
Highlights include:
- large set of IIO driver updates, additions, and cleanups
- new habanalabs device support added (loads of register maps much
like GPUs have)
- soundwire driver updates
- phy driver updates
- slimbus driver updates
- tiny virt driver fixes and updates
- misc driver fixes and updates
- interconnect driver updates
- hwtracing driver updates
- fpga driver updates
- extcon driver updates
- firmware driver updates
- counter driver update
- mhi driver fixes and updates
- binder driver fixes and updates
- speakup driver fixes
All of these have been in linux-next for a while without any reported
problems"
* tag 'char-misc-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (634 commits)
drivers: lkdtm: fix clang -Wformat warning
char: remove VR41XX related char driver
misc: Mark MICROCODE_MINOR unused
spmi: trace: fix stack-out-of-bound access in SPMI tracing functions
dt-bindings: iio: adc: Add compatible for MT8188
iio: light: isl29028: Fix the warning in isl29028_remove()
iio: accel: sca3300: Extend the trigger buffer from 16 to 32 bytes
iio: fix iio_format_avail_range() printing for none IIO_VAL_INT
iio: adc: max1027: unlock on error path in max1027_read_single_value()
iio: proximity: sx9324: add empty line in front of bullet list
iio: magnetometer: hmc5843: Remove duplicate 'the'
iio: magn: yas530: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: magnetometer: ak8974: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: veml6030: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: vcnl4035: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: vcnl4000: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: tsl2591: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr()
iio: light: tsl2583: Use DEFINE_RUNTIME_DEV_PM_OPS and pm_ptr()
iio: light: isl29028: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr()
iio: light: gp2ap002: Switch to DEFINE_RUNTIME_DEV_PM_OPS and pm_ptr()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy-for-5.20
- New support:
- Samsung FSD ufs phy
- Mediatek MT8365 dsi and tphy support
- Amlogic G12A Analog D-PHY driver
- Mediatek MT8188 tphy support
- Mediatek PCIe phy driver
- Cadence J721e DPHY support
- Qualcomm IPQ8074 PCIe Gen3 PHY support
- Nvidia Tegra PCIe PIPE2UPHY support
- Updates:
- Split of Qualcomm combo qmp phy driver to ufs, usb, pcie phy
drivers and associated cleanup of these drivers
* tag 'phy-for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (115 commits)
dt-bindings: phy: mediatek: tphy: add compatible for mt8188
phy: rockchip-inno-usb2: Ignore OTG IRQs in host mode
phy: qcom-qmp-usb: statify qmp_phy_vreg_l
phy: stm32: fix error return in stm32_usbphyc_phy_init
phy: phy-mtk-dp: change mtk_dp_phy_driver to static
phy: freescale: Add i.MX8qm Mixel LVDS PHY support
dt-bindings: phy: Add Freescale i.MX8qm Mixel LVDS PHY binding
dt-bindings: vendor-prefixes: Add prefix for Mixel, Inc.
phy: cadence-torrent: Remove unused `regmap` field from state struct
phy: cadence: Sierra: Remove unused `regmap` field from state struct
phy: samsung-ufs: ufs: change phy on/off control
phy: samsung-ufs: convert phy clk usage to clk_bulk API
phy: qcom-qmp-usb: define QPHY_V2_PCS_PLL_LOCK_CHK_DLY_TIME register
phy: qcom-qmp-usb: replace FLL layout writes for msm8996
phy: qcom-qmp: pcs-pcie-v4: add missing registers
phy: qcom-qmp: pcs-v3: add missing registers
phy: qcom-qmp: qserdes-com-v5: add missing registers
phy: qcom-qmp: qserdes-com-v4: add missing registers
phy: qcom-qmp: qserdes-com-v3: add missing registers
phy: qcom-qmp: qserdes-com: add missing registers
...
|
|
https://gitlab.freedesktop.org/drm/msm into drm-next
Next for v5.20
GPU:
- a619 support
- Fix for unclocked GMU register access
- Devcore dump enhancements
Core:
- client utilization via fdinfo support
- fix fence rollover issue
- gem: Lockdep false-positive warning fix
- gem: Switch to pfn mappings
DPU:
- constification of HW catalog
- support for using encoder as CRC source
- WB support on sc7180
- WB resolution fixes
DP:
- dropped custom bulk clock implementation
- made dp_bridge_mode_valid() return MODE_CLOCK_HIGH where applicable
- fix link retraining on resolution change
MDP5:
- MSM8953 perf data
HDMI:
- YAML'ification of schema
- dropped obsolete GPIO support
- misc cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtuqswBGPw-kCYzJvckK2RR1XTeUEgaXwVG_mvpbv3gPA@mail.gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into drm-next
Backmerge in rc6 so I can merge msm next easier.
Linux 5.19-rc6
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Vdda regulators are related to both eDP and DP phy so that it should be
managed at eDP and DP phy driver instead of controller. This patch removes
vdda regulators related functions out of eDP/DP controller.
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1657038556-2231-4-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|