summaryrefslogtreecommitdiff
path: root/drivers/idle
AgeCommit message (Collapse)AuthorFilesLines
2021-09-24intel_idle: enable interrupts before C1 on XeonsArtem Bityutskiy1-2/+11
Enable local interrupts before requesting C1 on the last two generations of Intel Xeon platforms: Sky Lake, Cascade Lake, Cooper Lake, Ice Lake. This decreases average C1 interrupt latency by about 5-10%, as measured with the 'wult' tool. The '->enter()' function of the driver enters C-states with local interrupts disabled by executing the 'monitor' and 'mwait' pair of instructions. If an interrupt happens, the CPU exits the C-state and continues executing instructions after 'mwait'. It does not jump to the interrupt handler, because local interrupts are disabled. The cpuidle subsystem enables interrupts a bit later, after doing some housekeeping. With this patch, we enable local interrupts before requesting C1. In this case, if the CPU wakes up because of an interrupt, it will jump to the interrupt handler right away. The cpuidle housekeeping will be done after the pending interrupt(s) are handled. Enabling interrupts before entering a C-state has measurable impact for faster C-states, like C1. Deeper, but slower C-states like C6 do not really benefit from this sort of change, because their latency is a lot higher comparing to the delay added by cpuidle housekeeping. This change was also tested with cyclictest and dbench. In case of Ice Lake, the average cyclictest latency decreased by 5.1%, and the average 'dbench' throughput increased by about 0.8%. Both tests were run for 4 hours with only C1 enabled (all other idle states, including 'POLL', were disabled). CPU frequency was pinned to HFM, and uncore frequency was pinned to the maximum value. The other platforms had similar single-digit percentage improvements. It is worth noting that this patch affects 'cpuidle' statistics a tiny bit. Before this patch, C1 residency did not include the interrupt handling time, but with this patch, it will include it. This is similar to what happens in case of the 'POLL' state, which also runs with interrupts enabled. Suggested-by: Len Brown <len.brown@intel.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2021-06-09intel_idle: Adjust the SKX C6 parameters if PC6 is disabledChen Yu1-0/+33
Because cpuidle assumes worst-case C-state parameters, PC6 parameters are used for describing C6, which is worst-case for requesting CC6. When PC6 is enabled, this is appropriate. But if PC6 is disabled in the BIOS, the exit latency and target residency should be adjusted accordingly. Exit latency: Previously the C6 exit latency was measured as the PC6 exit latency. With PC6 disabled, the C6 exit latency should be the one of CC6. Target residency: With PC6 disabled, the idle duration within [CC6, PC6) would make the idle governor choose C1E over C6. This would cause low energy-efficiency. We should lower the bar to request C6 when PC6 is disabled. To fill this gap, check if PC6 is disabled in the BIOS in the MSR_PKG_CST_CONFIG_CONTROL(0xe2) register. If so, use the CC6 exit latency for C6 and set target_residency to 3 times of the new exit latency. [This is consistent with how intel_idle driver uses _CST to calculate the target_residency.] As a result, the OS would be more likely to choose C6 over C1E when PC6 is disabled, which is reasonable, because if C6 is enabled, it implies that the user cares about energy, so choosing C6 more frequently makes sense. The new CC6 exit latency of 92us was measured with wult[1] on SKX via NIC wakeup as the 99.99th percentile. Also CLX and CPX both have the same CPU model number as SkX, but their CC6 exit latencies are similar to the SKX one, 96us and 89us respectively, so reuse the SKX value for them. There is a concern that it might be better to use a more generic approach instead of optimizing every platform. However, if the required code complexity and different PC6 bit interpretation on different platforms are taken into account, tuning the code per platform seems to be an acceptable tradeoff. Link: https://intel.github.io/wult/ # [1] Suggested-by: Len Brown <len.brown@intel.com> Signed-off-by: Chen Yu <yu.c.chen@intel.com> Reviewed-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> [ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2021-04-08intel_idle: add Iclelake-D supportArtem Bityutskiy1-0/+1
This patch adds Icelake Xeon D support to the intel_idle driver. Since Icelake D and Icelake SP C-state characteristics the same, we use Icelake SP C-states table for Icelake D as well. Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Acked-by: Chen Yu <yu.c.chen@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2021-03-18intel_idle: update ICX C6 dataArtem Bityutskiy1-2/+2
Change IceLake Xeon C6 latency from 128 us to 170 us. The latency was measured with the "wult" tool and corresponds to the 99.99th percentile when measuring with the "nic" method. Note, the 128 us figure correspond to the median latency, but in intel_idle we use the "worst case" latency figure instead. C6 target residency was increased from 384 us to 600 us, which may result in less C6 residency in some workloads. This value was tested and compared to values 384, and 1000. Value 600 is a reasonable tradeoff between power and performance. Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Acked-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2021-01-22intel_idle: remove definition of DEBUGTom Rix1-1/+1
Defining DEBUG should only be done in development. So remove DEBUG. Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-12-30intel_idle: add SnowRidge C-state tableArtem Bityutskiy1-1/+40
Add C-state table for the SnowRidge SoC which is found on Intel Jacobsville platforms. The following has been changed. 1. C1E latency changed from 10us to 15us. It was measured using the open source "wult" tool (the "nic" method, 15us is the 99.99th percentile). 2. C1E power break even changed from 20us to 25us, which may result in less C1E residency in some workloads. 3. C6 latency changed from 50us to 130us. Measured the same way as C1E. The C6 C-state is supported only by some SnowRidge revisions, so add a C-state table commentary about this. On SnowRidge, C6 support is enumerated via the usual mechanism: "mwait" leaf of the "cpuid" instruction. The 'intel_idle' driver does check this leaf, so even though C6 is present in the table, the driver will only use it if the CPU does support it. Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-12-03intel_idle: Build fixPeter Zijlstra1-14/+14
Because CONFIG_ soup. Fixes: 6e1d2bc675bd ("intel_idle: Fix intel_idle() vs tracing") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20201130115402.GO3040@hirez.programming.kicks-ass.net
2020-11-24intel_idle: Fix intel_idle() vs tracingPeter Zijlstra1-17/+20
cpuidle->enter() callbacks should not call into tracing because RCU has already been disabled. Instead of doing the broadcast thing itself, simply advertise to the cpuidle core that those states stop the timer. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://lkml.kernel.org/r/20201123143510.GR3021@hirez.programming.kicks-ass.net
2020-10-27intel_idle: Fix max_cstate for processor models without C-state tablesChen Yu1-1/+1
Currently intel_idle driver gets the c-state information from ACPI _CST if the processor model is not recognized by it. However the c-state in _CST starts with index 1 which is different from the index in intel_idle driver's internal c-state table. While intel_idle_max_cstate_reached() was previously introduced to deal with intel_idle driver's internal c-state table, re-using this function directly on _CST is incorrect. Fix this by subtracting 1 from the index when checking max_cstate in the _CST case. For example, append intel_idle.max_cstate=1 in boot command line, Before the patch: grep . /sys/devices/system/cpu/cpu0/cpuidle/state*/name POLL After the patch: grep . /sys/devices/system/cpu/cpu0/cpuidle/state*/name /sys/devices/system/cpu/cpu0/cpuidle/state0/name:POLL /sys/devices/system/cpu/cpu0/cpuidle/state1/name:C1_ACPI Fixes: 18734958e9bf ("intel_idle: Use ACPI _CST for processor models without C-state tables") Reported-by: Pengfei Xu <pengfei.xu@intel.com> Cc: 5.6+ <stable@vger.kernel.org> # 5.6+ Signed-off-by: Chen Yu <yu.c.chen@intel.com> [ rjw: Changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-10-16intel_idle: Ignore _CST if control cannot be taken from the platformMel Gorman1-4/+3
e6d4f08a6776 ("intel_idle: Use ACPI _CST on server systems") avoids enabling c-states that have been disabled by the platform with the exception of C1E. Unfortunately, BIOS implementations are not always consistent in terms of how capabilities are advertised and control cannot always be handed over. If control cannot be handed over then intel_idle reports that "ACPI _CST not found or not usable" but does not clear acpi_state_table.count meaning the information is still partially used. This patch ignores ACPI information if CST control cannot be requested from the platform. This was only observed on a number of Haswell platforms that had identical CPUs but not identical BIOS versions. While this problem may be rare overall, 24 separate test cases bisected to this specific commit across 4 separate test machines and is worth addressing. If the situation occurs, the kernel behaves as it did before commit e6d4f08a6776 and uses any c-states that are discovered. The affected test cases were all ones that involved a small number of processes -- exec microbenchmark, pipe microbenchmark, git test suite, netperf, tbench with one client and system call microbenchmark. Each case benefits from being able to use turboboost which is prevented if the lower c-states are unavailable. This may mask real regressions specific to older hardware so it is worth addressing. C-state status before and after the patch 5.9.0-vanilla POLL latency:0 disabled:0 default:enabled 5.9.0-vanilla C1 latency:2 disabled:0 default:enabled 5.9.0-vanilla C1E latency:10 disabled:0 default:enabled 5.9.0-vanilla C3 latency:33 disabled:1 default:disabled 5.9.0-vanilla C6 latency:133 disabled:1 default:disabled 5.9.0-ignore-cst-v1r1 POLL latency:0 disabled:0 default:enabled 5.9.0-ignore-cst-v1r1 C1 latency:2 disabled:0 default:enabled 5.9.0-ignore-cst-v1r1 C1E latency:10 disabled:0 default:enabled 5.9.0-ignore-cst-v1r1 C3 latency:33 disabled:0 default:enabled 5.9.0-ignore-cst-v1r1 C6 latency:133 disabled:0 default:enabled Patch enables C3/C6. Netperf UDP_STREAM netperf-udp 5.5.0 5.9.0 vanilla ignore-cst-v1r1 Hmean send-64 193.41 ( 0.00%) 226.54 * 17.13%* Hmean send-128 392.16 ( 0.00%) 450.54 * 14.89%* Hmean send-256 769.94 ( 0.00%) 881.85 * 14.53%* Hmean send-1024 2994.21 ( 0.00%) 3468.95 * 15.85%* Hmean send-2048 5725.60 ( 0.00%) 6628.99 * 15.78%* Hmean send-3312 8468.36 ( 0.00%) 10288.02 * 21.49%* Hmean send-4096 10135.46 ( 0.00%) 12387.57 * 22.22%* Hmean send-8192 17142.07 ( 0.00%) 19748.11 * 15.20%* Hmean send-16384 28539.71 ( 0.00%) 30084.45 * 5.41%* Fixes: e6d4f08a6776 ("intel_idle: Use ACPI _CST on server systems") Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Cc: 5.6+ <stable@vger.kernel.org> # 5.6+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-10-16intel_idle: mention assumption that WBINVD is not neededAlexander Monakov1-2/+6
Intel SDM does not explicitly say that entering a C-state via MWAIT will implicitly flush CPU caches as appropriate for that C-state. However, documentation for individual Intel CPU generations does mention this behavior. Since intel_idle binds to any Intel CPU with MWAIT, list this assumption of MWAIT behavior. In passing, reword opening comment to make it clear that the driver can load on any old and future Intel CPU with MWAIT. Signed-off-by: Alexander Monakov <amonakov@ispras.ru> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-08-26cpuidle: Make CPUIDLE_FLAG_TLB_FLUSHED genericPeter Zijlstra1-16/+0
This allows moving the leave_mm() call into generic code before rcu_idle_enter(). Gets rid of more trace_*_rcuidle() users. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Marco Elver <elver@google.com> Link: https://lkml.kernel.org/r/20200821085348.369441600@infradead.org
2020-08-04Merge tag 'uninit-macro-v5.9-rc1' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux Pull uninitialized_var() macro removal from Kees Cook: "This is long overdue, and has hidden too many bugs over the years. The series has several "by hand" fixes, and then a trivial treewide replacement. - Clean up non-trivial uses of uninitialized_var() - Update documentation and checkpatch for uninitialized_var() removal - Treewide removal of uninitialized_var()" * tag 'uninit-macro-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: compiler: Remove uninitialized_var() macro treewide: Remove uninitialized_var() usage checkpatch: Remove awareness of uninitialized_var() macro mm/debug_vm_pgtable: Remove uninitialized_var() usage f2fs: Eliminate usage of uninitialized_var() macro media: sur40: Remove uninitialized_var() usage KVM: PPC: Book3S PR: Remove uninitialized_var() usage clk: spear: Remove uninitialized_var() usage clk: st: Remove uninitialized_var() usage spi: davinci: Remove uninitialized_var() usage ide: Remove uninitialized_var() usage rtlwifi: rtl8192cu: Remove uninitialized_var() usage b43: Remove uninitialized_var() usage drbd: Remove uninitialized_var() usage x86/mm/numa: Remove uninitialized_var() usage docs: deprecated.rst: Add uninitialized_var()
2020-07-30intel_idle: Customize IceLake server supportChen Yu1-0/+36
On ICX platform, the C1E auto-promotion is enabled by default. As a result, the CPU might fall into C1E more offen than previous platforms. Besides, the C1E is not exposed to sysfs on ICX, which is inconsistent with previous server platforms. So disable C1E auto-promotion and expose C1E as a separate idle state, so the C1E and C6 can be disabled via sysfs when necessary. Beside C1 and C1E, the exit latency of C6 was measured by a dedicated tool. However the exit latency(41us) exposed by _CST is much smaller than the one we measured(128us). This is probably due to the _CST uses the exit latency when woken up from PC0+C6, rather than PC6+C6 when C6 was measured. Choose the latter as we need the longest latency in theory. Reported-by: kernel test robot <lkp@intel.com> Tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Reviewed-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Chen Yu <yu.c.chen@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-07-29cpuidle: change enter_s2idle() prototypeNeal Liu1-2/+4
Control Flow Integrity(CFI) is a security mechanism that disallows changes to the original control flow graph of a compiled binary, making it significantly harder to perform such attacks. init_state_node() assign same function callback to different function pointer declarations. static int init_state_node(struct cpuidle_state *idle_state, const struct of_device_id *matches, struct device_node *state_node) { ... idle_state->enter = match_id->data; ... idle_state->enter_s2idle = match_id->data; } Function declarations: struct cpuidle_state { ... int (*enter) (struct cpuidle_device *dev, struct cpuidle_driver *drv, int index); void (*enter_s2idle) (struct cpuidle_device *dev, struct cpuidle_driver *drv, int index); }; In this case, either enter() or enter_s2idle() would cause CFI check failed since they use same callee. Align function prototype of enter() since it needs return value for some use cases. The return value of enter_s2idle() is no need currently. Signed-off-by: Neal Liu <neal.liu@mediatek.com> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-07-16treewide: Remove uninitialized_var() usageKees Cook1-1/+1
Using uninitialized_var() is dangerous as it papers over real bugs[1] (or can in the future), and suppresses unrelated compiler warnings (e.g. "unused variable"). If the compiler thinks it is uninitialized, either simply initialize the variable or make compiler changes. In preparation for removing[2] the[3] macro[4], remove all remaining needless uses with the following script: git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \ xargs perl -pi -e \ 's/\buninitialized_var\(([^\)]+)\)/\1/g; s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;' drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid pathological white-space. No outstanding warnings were found building allmodconfig with GCC 9.3.0 for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64, alpha, and m68k. [1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/ [2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/ [3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/ [4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/ Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5 Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs Signed-off-by: Kees Cook <keescook@chromium.org>
2020-06-29intel_idle: Eliminate redundant static variableRafael J. Wysocki1-8/+3
The value of the lapic_timer_always_reliable static variable in the intel_idle driver reflects the boot_cpu_has(X86_FEATURE_ARAT) value and so it also reflects the static_cpu_has(X86_FEATURE_ARAT) value. Hence, the lapic_timer_always_reliable check in intel_idle() is redundant and apart from this lapic_timer_always_reliable is only used in two places in which boot_cpu_has(X86_FEATURE_ARAT) can be used directly. Eliminate the lapic_timer_always_reliable variable in accordance with the above observations. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-03-31Merge branch 'perf-core-for-linus' of ↵Linus Torvalds1-41/+38
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull perf updates from Ingo Molnar: "The main changes in this cycle were: Kernel side changes: - A couple of x86/cpu cleanups and changes were grandfathered in due to patch dependencies. These clean up the set of CPU model/family matching macros with a consistent namespace and C99 initializer style. - A bunch of updates to various low level PMU drivers: * AMD Family 19h L3 uncore PMU * Intel Tiger Lake uncore support * misc fixes to LBR TOS sampling - optprobe fixes - perf/cgroup: optimize cgroup event sched-in processing - misc cleanups and fixes Tooling side changes are to: - perf {annotate,expr,record,report,stat,test} - perl scripting - libapi, libperf and libtraceevent - vendor events on Intel and S390, ARM cs-etm - Intel PT updates - Documentation changes and updates to core facilities - misc cleanups, fixes and other enhancements" * 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (89 commits) cpufreq/intel_pstate: Fix wrong macro conversion x86/cpu: Cleanup the now unused CPU match macros hwrng: via_rng: Convert to new X86 CPU match macros crypto: Convert to new CPU match macros ASoC: Intel: Convert to new X86 CPU match macros powercap/intel_rapl: Convert to new X86 CPU match macros PCI: intel-mid: Convert to new X86 CPU match macros mmc: sdhci-acpi: Convert to new X86 CPU match macros intel_idle: Convert to new X86 CPU match macros extcon: axp288: Convert to new X86 CPU match macros thermal: Convert to new X86 CPU match macros hwmon: Convert to new X86 CPU match macros platform/x86: Convert to new CPU match macros EDAC: Convert to new X86 CPU match macros cpufreq: Convert to new X86 CPU match macros ACPI: Convert to new X86 CPU match macros x86/platform: Convert to new CPU match macros x86/kernel: Convert to new CPU match macros x86/kvm: Convert to new CPU match macros x86/perf/events: Convert to new CPU match macros ...
2020-03-24intel_idle: Convert to new X86 CPU match macrosThomas Gleixner1-41/+38
The new macro set has a consistent namespace and uses C99 initializers instead of the grufty C89 ones. Get rid the of the local macro wrappers for consistency. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lkml.kernel.org/r/20200320131510.193755545@linutronix.de
2020-02-12intel_idle: Update copyright notice, known limitations and versionRafael J. Wysocki1-7/+3
Update the copyright notice in intel_idle.c to cover the recent changes, drop the description of a "known limitation" that is not a limitation any more and bump up the driver version number. No functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-02-12intel_idle: Define CPUIDLE_FLAG_TLB_FLUSHED as BIT(16)Rafael J. Wysocki1-1/+1
Use the BIT() macro for defining CPUIDLE_FLAG_TLB_FLUSHED instead of the hex bit encoding of the same value. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-02-12intel_idle: Clean up kerneldoc comments for multiple functionsRafael J. Wysocki1-19/+21
Turn the description comments of some functions in the intel_idle driver into proper kerneldoc ones and clean them up. No functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-02-12intel_idle: Reorder declarations of static variablesRafael J. Wysocki1-2/+3
Reorder declarations of static variables so that the __initdata ones are declared together. No functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-02-12intel_idle: Annotate init time data structuresRafael J. Wysocki1-39/+39
Add __initdata or __initconst annotations to the static data structures that are only used during the initialization of the driver. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-02-12intel_idle: Add __initdata annotations to init time variablesRafael J. Wysocki1-9/+12
Annotate static variables cpuidle_state_table and mwait_substates with __initdata, because they are only used during the initialization of the driver. Also notice that static variable icpu could be annotated analogously and the structure pointed to by it could be __initconst, but two of its fields are accessed via icpu in intel_idle_cpu_init() and auto_demotion_disable(), so introduce two new static variables, auto_demotion_disable_flags and disable_promotion_to_c1e, to hold the values of these fields, set them during the initialization and use them in those functions instead of accessing the source data structure via icpu. That allows icpu to be annotated with __initdata, so do that, and it will also allow some __initconst annotations to be added subsequently. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-02-12intel_idle: Relocate definitions of cpuidle callbacksRafael J. Wysocki1-79/+75
Move the definitions of intel_idle() and intel_idle_s2idle() before the definitions of cpuidle_state structures referring to them to avoid having to use additional declarations of them (and drop those declarations). No functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-02-12intel_idle: Clean up definitions of cpuidle callbacksRafael J. Wysocki1-12/+27
Add proper kerneldoc descriptions to intel_idle() and intel_idle_s2idle(), annotate the latter with __cpuidle and reorder the declarations of local variables in both of them to reflect the mwait_idle_with_hints() arguments order. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-02-12intel_idle: Simplify LAPIC timer reliability checksRafael J. Wysocki1-14/+13
The lapic_timer_always_reliable variable really takes only two values and some arithmetic in intel_idle() related to comparing it with the target C-state's MWAIT hint value is unnecessary. Simplify the code by replacing lapic_timer_always_reliable with a bool variable lapic_timer_always_reliable and dropping the LAPIC_TIMER_ALWAYS_RELIABLE symbol along with the excess computations in intel_idle(). While at it, add a comment explaining the branch taken in intel_idle() if the LAPIC timer is only reliable in C1 and modify the related debug message in intel_idle_init() accordingly (the modification of this message in the only expected functional impact of the change made here). Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-02-03intel_idle: Introduce 'states_off' module parameterRafael J. Wysocki1-3/+20
In certain system configurations it may not be desirable to use some C-states assumed to be available by intel_idle and the driver needs to be prevented from using them even before the cpuidle sysfs interface becomes accessible to user space. Currently, the only way to achieve that is by setting the 'max_cstate' module parameter to a value lower than the index of the shallowest of the C-states in question, but that may be overly intrusive, because it effectively makes all of the idle states deeper than the 'max_cstate' one go away (and the C-state to avoid may be in the middle of the range normally regarded as available). To allow that limitation to be overcome, introduce a new module parameter called 'states_off' to represent a list of idle states to be disabled by default in the form of a bitmask and update the documentation to cover it. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-02-03intel_idle: Introduce 'use_acpi' module parameterRafael J. Wysocki1-2/+9
For diagnostics, it is generally useful to be able to make intel_idle take the system's ACPI tables into consideration even if that is not required for the processor model in there, so introduce a new module parameter, 'use_acpi', to make that happen and update the documentation to cover it. While at it, fix the 'no_acpi' module parameter name in the documentation. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-01-28Merge branch 'x86-cpu-for-linus' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 cpu-features updates from Ingo Molnar: "The biggest change in this cycle was a large series from Sean Christopherson to clean up the handling of VMX features. This both fixes bugs/inconsistencies and makes the code more coherent and future-proof. There are also two cleanups and a minor TSX syslog messages enhancement" * 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits) x86/cpu: Remove redundant cpu_detect_cache_sizes() call x86/cpu: Print "VMX disabled" error message iff KVM is enabled KVM: VMX: Allow KVM_INTEL when building for Centaur and/or Zhaoxin CPUs perf/x86: Provide stubs of KVM helpers for non-Intel CPUs KVM: VMX: Use VMX_FEATURE_* flags to define VMCS control bits KVM: VMX: Check for full VMX support when verifying CPU compatibility KVM: VMX: Use VMX feature flag to query BIOS enabling KVM: VMX: Drop initialization of IA32_FEAT_CTL MSR x86/cpufeatures: Add flag to track whether MSR IA32_FEAT_CTL is configured x86/cpu: Set synthetic VMX cpufeatures during init_ia32_feat_ctl() x86/cpu: Print VMX flags in /proc/cpuinfo using VMX_FEATURES_* x86/cpu: Detect VMX features on Intel, Centaur and Zhaoxin CPUs x86/vmx: Introduce VMX_FEATURES_* x86/cpu: Clear VMX feature flag if VMX is not fully enabled x86/zhaoxin: Use common IA32_FEAT_CTL MSR initialization x86/centaur: Use common IA32_FEAT_CTL MSR initialization x86/mce: WARN once if IA32_FEAT_CTL MSR is left unlocked x86/intel: Initialize IA32_FEAT_CTL MSR at boot tools/x86: Sync msr-index.h from kernel sources selftests, kvm: Replace manual MSR defs with common msr-index.h ...
2020-01-23intel_idle: Clean up irtl_2_usec()Rafael J. Wysocki1-8/+10
Move the irtl_ns_units[] definition into irtl_2_usec() which is the only user of it, use div_u64() for the division in there (as the divisor is small enough) and use the NSEC_PER_USEC symbol for the divisor. Also convert the irtl_2_usec() comment to a proper kerneldo one. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-01-23intel_idle: Move 3 functions closer to their callersRafael J. Wysocki1-33/+34
Move intel_idle_verify_cstate(), auto_demotion_disable() and c1e_promotion_disable() closer to their callers. While at it, annotate intel_idle_verify_cstate() with __init, as it is only used during the initialization of the driver. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-01-23intel_idle: Annotate initialization code and data structuresRafael J. Wysocki1-13/+14
Annotate the functions that are only used at the initialization time with __init and the data structures used by them with __initdata or __initconst. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-01-23intel_idle: Move and clean up intel_idle_cpuidle_devices_uninit()Rafael J. Wysocki1-15/+11
Move intel_idle_cpuidle_devices_uninit() closer to its caller, intel_idle_init(), add the __init modifier to its header, drop a redundant local variable from it and fix up its kerneldoc comment. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-01-23intel_idle: Rearrange intel_idle_cpuidle_driver_init()Rafael J. Wysocki1-18/+6
Notice that intel_idle_state_table_update() only needs to be called if icpu is not NULL, so fold it into intel_idle_init_cstates_icpu(), and pass a pointer to the driver object to intel_idle_cpuidle_driver_init() as an argument instead of referencing it locally in there. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-01-23intel_idle: Clean up NULL pointer check in intel_idle_init()Rafael J. Wysocki1-1/+1
Instead of comparing intel_idle_cpuidle_devices with NULL apply the "!" (not) operator to it when checking it against NULL. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-01-23intel_idle: Fold intel_idle_probe() into intel_idle_init()Rafael J. Wysocki1-55/+42
There is no particular reason why intel_idle_probe() needs to be a separate function and folding it into intel_idle_init() causes the code to be somewhat easier to follow, so do just that. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-01-23intel_idle: Eliminate __setup_broadcast_timer()Rafael J. Wysocki1-9/+1
The __setup_broadcast_timer() static function is only called in one place and "true" is passed to it as the argument in there, so effectively it is a wrapper arround tick_broadcast_enable(). To simplify the code, call tick_broadcast_enable() directly instead of __setup_broadcast_timer() and drop the latter. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-01-13x86/msr-index: Clean up bit defines for IA32_FEATURE_CONTROL MSRSean Christopherson1-1/+1
As pointed out by Boris, the defines for bits in IA32_FEATURE_CONTROL are quite a mouthful, especially the VMX bits which must differentiate between enabling VMX inside and outside SMX (TXT) operation. Rename the MSR and its bit defines to abbreviate FEATURE_CONTROL as FEAT_CTL to make them a little friendlier on the eyes. Arguably, the MSR itself should keep the full IA32_FEATURE_CONTROL name to match Intel's SDM, but a future patch will add a dedicated Kconfig, file and functions for the MSR. Using the full name for those assets is rather unwieldy, so bite the bullet and use IA32_FEAT_CTL so that its nomenclature is consistent throughout the kernel. Opportunistically, fix a few other annoyances with the defines: - Relocate the bit defines so that they immediately follow the MSR define, e.g. aren't mistaken as belonging to MISC_FEATURE_CONTROL. - Add whitespace around the block of feature control defines to make it clear they're all related. - Use BIT() instead of manually encoding the bit shift. - Use "VMX" instead of "VMXON" to match the SDM. - Append "_ENABLED" to the LMCE (Local Machine Check Exception) bit to be consistent with the kernel's verbiage used for all other feature control bits. Note, the SDM refers to the LMCE bit as LMCE_ON, likely to differentiate it from IA32_MCG_EXT_CTL.LMCE_EN. Ignore the (literal) one-off usage of _ON, the SDM is simply "wrong". Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20191221044513.21680-2-sean.j.christopherson@intel.com
2019-12-27intel_idle: Use ACPI _CST on server systemsRafael J. Wysocki1-20/+50
In many cases, especially on server systems, it is desirable to avoid enabling C-states that have been disabled in the platform firmware (BIOS) setup, except for C1E. As a rule, the C-states disabled this way are not listed by ACPI _CST, so if that is used by intel_idle along with the specific table of C-states that it has for the given processor, the C-states disabled through the platform firmware will not be enabled by default by intel_idle. Accordingly, set the use_acpi flag (introduced previously) in all server processor profiles defined in intel_idle (so as to make it use ACPI _CST to decide which C-states to enable by default) and set the CPUIDLE_FLAG_ALWAYS_ENABLE flag (also introduced previously) for C1E in all C-states tables in intel_idle that contain C1 too (so that C1E is enabled regardless of whether or not it is listed by ACPI _CST). Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-12-27intel_idle: Add module parameter to prevent ACPI _CST from being usedRafael J. Wysocki1-0/+9
Add a new module parameter called "no_acpi" to the intel_idle driver to allow the driver to be prevented from using ACPI _CST via kernel command line. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-12-27intel_idle: Allow ACPI _CST to be used for selected known processorsRafael J. Wysocki1-3/+42
Update the intel_idle driver to get the C-states information from ACPI _CST in some cases in which the processor is known to the driver, as long as that information is available and the new use_acpi flag is set in the profile of the processor in question. In the cases when there is a specific table of C-states for the given processor in the driver, that table is used as the primary source of information on the available C-states, but if ACPI _CST is present, the C-states that are not listed by it will not be enabled by default (they still can be enabled later by user space via sysfs, though). The new CPUIDLE_FLAG_ALWAYS_ENABLE flag can be used for marking C-states that should be enabled by default even if they are not listed by ACPI _CST. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-12-27intel_idle: Use ACPI _CST for processor models without C-state tablesRafael J. Wysocki1-28/+162
Modify the intel_idle driver to get the C-states information from ACPI _CST if the processor model is not recognized by it. The processor is still required to support MWAIT and the information from ACPI _CST will only be used if all of the C-states listed by _CST are of the ACPI_CSTATE_FFH type (which means that they are expected to be entered via MWAIT). Moreover, the driver assumes that the _CST information is the same for all CPUs in the system, so it is sufficient to evaluate _CST for one of them and extract the common list of C-states from there. Also _CST is evaluated once at the system initialization time and the driver does not respond to _CST change notifications (that can be changed in the future). The main functional difference between intel_idle with this change and the ACPI processor driver is that the former sets the target residency to be equal to the exit latency (provided by _CST) for C1-type C-states and to 3 times the exit latency value for the other C-state types, whereas the latter obtains the target residency by multiplying the exit latency by the same number (2 by default) for all C-state types. Therefore it is expected that in general using the former instead of the latter on the same system will lead to improved energy-efficiency. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-12-27intel_idle: Refactor intel_idle_cpuidle_driver_init()Rafael J. Wysocki1-24/+25
Move the C-state verification and checks from intel_idle_cpuidle_driver_init() to a separate function, intel_idle_verify_cstate(), and make the former call it after checking the CPUIDLE_FLAG_UNUSABLE state flag. Also combine the drv->states[] updates with the incrementation of drv->state_count. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-11-29cpuidle: Drop disabled field from struct cpuidle_stateRafael J. Wysocki1-3/+3
After recent cpuidle updates the "disabled" field in struct cpuidle_state is only used by two drivers (intel_idle and shmobile cpuidle) for marking unusable idle states, but that may as well be achieved with the help of a state flag, so define an "unusable" idle state flag, CPUIDLE_FLAG_UNUSABLE, make the drivers in question use it instead of the "disabled" field and make the core set CPUIDLE_STATE_DISABLED_BY_DRIVER for the idle states with that flag set. After the above changes, the "disabled" field in struct cpuidle_state is not used any more, so drop it. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-08-28x86/intel: Aggregate microserver namingPeter Zijlstra1-4/+4
Currently big microservers have _XEON_D while small microservers have _X, Make it uniformly: _D. for i in `git grep -l "\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*_\(X\|XEON_D\)"` do sed -i -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*ATOM.*\)_X/\1_D/g' \ -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*\)_XEON_D/\1_D/g' ${i} done Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Tony Luck <tony.luck@intel.com> Cc: x86@kernel.org Cc: Dave Hansen <dave.hansen@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Link: https://lkml.kernel.org/r/20190827195122.677152989@infradead.org
2019-08-28x86/intel: Aggregate big core graphics namingPeter Zijlstra1-2/+2
Currently big core clients with extra graphics on have: - _G - _GT3E Make it uniformly: _G for i in `git grep -l "\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*_GT3E"` do sed -i -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*\)_GT3E/\1_G/g' ${i} done Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Tony Luck <tony.luck@intel.com> Cc: x86@kernel.org Cc: Dave Hansen <dave.hansen@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Link: https://lkml.kernel.org/r/20190827195122.622802314@infradead.org
2019-08-28x86/intel: Aggregate big core mobile namingPeter Zijlstra1-3/+3
Currently big core mobile chips have either: - _L - _ULT - _MOBILE Make it uniformly: _L. for i in `git grep -l "\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*_\(MOBILE\|ULT\)"` do sed -i -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*\)_\(MOBILE\|ULT\)/\1_L/g' ${i} done Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Tony Luck <tony.luck@intel.com> Cc: x86@kernel.org Cc: Dave Hansen <dave.hansen@intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190827195122.568978530@infradead.org
2019-08-28x86/intel: Aggregate big core client namingPeter Zijlstra1-5/+5
Currently the big core client models either have: - no OPTDIFF - _CORE - _DESKTOP Make it uniformly: 'no OPTDIFF'. for i in `git grep -l "\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*_\(CORE\|DESKTOP\)"` do sed -i -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*\)_\(CORE\|DESKTOP\)/\1/g' ${i} done Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Tony Luck <tony.luck@intel.com> Cc: x86@kernel.org Cc: Dave Hansen <dave.hansen@intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190827195122.513945586@infradead.org